Matrox G200 i DRI
Hej mam pytanko (potrzebuje jakiegos drogowskazu) - czyalem doc'e i liste, ale
sie zgubilem
kernel 2.4.19, xy 4.2.1, matrox g200
pytanie - jak powinno sie obiawiac dzialanie DRI/OpenGL - bo np glxinfo pokazuje
direct rendering: No
czyli ze nie ma wsparcia - tak?
Z rzeczy waznych:
Kernel przy starcie:
Linux agpgart interface v0.99 (c) Jeff Hartmann
agpgart: Maximum main memory to use for agp memory: 439M
agpgart: Detected Intel 440BX chipset
agpgart: AGP aperture is 8M @ 0xe7800000
[drm] AGP 0.99 on Intel 440BX @ 0xe7800000 8MB
[drm] Initialized mga 3.0.2 20010321 on minor 0
czyli wszystko oki
Xy przy starcie (laduja DRI)
(II) LoadModule: "dri"
(II) Loading /usr/X11R6/lib/modules/extensions/libdri.a
(II) Module dri: vendor="The XFree86 Project"
...
(II) MGA(0): [drm] bpp: 16 depth: 16
(II) MGA(0): [drm] Sarea 2200+664: 2864
drmOpenDevice: minor is 0
drmOpenDevice: node name is /dev/dri/card0
drmOpenDevice: open result is 6, (OK)
drmOpenDevice: minor is 0
drmOpenDevice: node name is /dev/dri/card0
drmOpenDevice: open result is 6, (OK)
drmOpenDevice: minor is 0
drmOpenDevice: node name is /dev/dri/card0
drmOpenDevice: open result is 6, (OK)
drmGetBusid returned ''
(II) MGA(0): [drm] created "mga" driver at busid "PCI:1:0:0"
(II) MGA(0): [drm] added 8192 byte SAREA at 0xe188e000
(II) MGA(0): [drm] mapped SAREA 0xe188e000 to 0x40018000
(II) MGA(0): [drm] framebuffer handle = 0xe6000000
(II) MGA(0): [drm] added 1 reserved context for kernel
(II) MGA(0): [agp] Mode 0x1f000201 [AGP 0x8086/0x7190; Card 0x102b/0x0521]
(II) MGA(0): [drm] Disabling AGP 2x PLL encoding
(II) MGA(0): [agp] 12288 kB allocated with handle 0xe1891000
(EE) MGA(0): [agp] Could not bind memory
(EE) MGA(0): [drm] failed to remove DRM signal handler
(II) MGA(0): [drm] removed 1 reserved context for kernel
DRIUnlock called when not locked
(II) MGA(0): [drm] unmapping 8192 bytes of SAREA 0xe188e000 at 0x40018000
... Pytanie jesli glxinfo pokazuje faktycznie brak wsparcie dla OpenGL to co
jest zle (w czesci z XFree86.log) i co ewentualnie trzeba zmienic. Robilem wsio
jak pisza w README.DRI, pozniej sciagnalem nowe DRI (zrodla) i finalnie
sterowniki ze strony matroxa (+matrox hal) i ciagle nic. Glxgears daje mi 140fps
(PIII 800mhz) - ale wszystko odpala sie software mode.
uff to chyba wszystko - jak ktos moze (i ma chwilke) by cos odpisac to bede
dzwieczny.
Pozdrawiam
--
Adrian (Sauron) Siemieniak /,/ .. Who can destroy The Thing,
sauron{at}rpg{dot}pl /`/ controls The Thing ... (DUNE)
Reply to: