Re: Wifi in Lenny einrichten
Am Freitag, 26. November 2010 schrieb Siegfrid Brandstätter:
> Hallo Debianer,
>
> leider habe ich keine Ahnung wie ich vorgehen soll um das Wifi in
> einem Laptop mit Lenny einzurichten. Google hat mich mit viel Infos
> eingedeckt, aber ich bin total verunsichert was und wie ich es
> anwenden soll.
>
Was ich noch vergessen habe, es handelt sich um ein "Noname Gerät"
in der Seite des Vertreibers steht:
Connections:
· LAN 10/100 M Ethernet Controller
· Wi-Fi IEEE 802.11b/g/n
· 2 USB 2.0 Ports
· 1 mini HDMI port
· Card Reader
· Bluetooth
> Mit dmesg habe ich gefunden: "RTL8102e"und ?"WiFi USB Dongle"?
>
> 2.899284] r8169 Gigabit Ethernet driver 2.2LK-NAPI loaded
> [ 2.899430] ACPI: PCI Interrupt 0000:02:00.0[A] -> GSI 16 (level,
> low) -> IRQ 16
> [ 2.899615] PCI: Setting latency timer of device 0000:02:00.0 to
> 64 [ 2.901464] eth0: RTL8102e at 0xf8854000, 00:e0:4c:12:3c:6a,
> XID 34a00000 IRQ 222
> [ 2.945680] No dock devices found.
> [ 3.001001] SCSI subsystem initialized
> [ 3.093257] libata version 3.00 loaded.
> [ 3.162226] Uniform Multi-Platform E-IDE driver
> [ 3.162226] ide: Assuming 33MHz system bus speed for PIO modes;
> override with idebus=xx
> [ 3.172190] ICH7: IDE controller (0x8086:0x27df rev 0x02) at PCI
> slot 0000:00:1f.1
> [ 3.172190] ACPI: PCI Interrupt 0000:00:1f.1[B] -> GSI 19 (level,
> low) -> IRQ 19
> [ 3.172190] ICH7: not 100% native mode: will probe irqs later
> [ 3.172190] ICH7: IDE port disabled
> [ 3.172190] ide0: BM-DMA at 0x1810-0x1817
> [ 3.172190] Probing IDE interface ide0...
> [ 3.554723] usb 5-3: new high speed USB device using ehci_hcd and
> address 3
>
>
>
> 4.204868] usb 5-5: configuration #1 chosen from 1 choice
> [ 4.204868] usb 5-5: New USB device found, idVendor=05e1,
> idProduct=0100
> [ 4.204868] usb 5-5: New USB device strings: Mfr=1, Product=2,
> SerialNumber=3
> [ 4.204868] usb 5-5: Product: WiFi USB Dongle
> [ 4.204868] usb 5-5: Manufacturer: Syntek Semi Co..
> [ 4.204868] usb 5-5: SerialNumber: Manufacture
> [ 4.293129] scsi 0:0:0:0: Direct-Access ATA FUJITSU
> MHZ2160B 0000 PQ: 0 ANSI: 5
> [ 4.346683] Driver 'sd' needs updating - please use bus_type
> methods
>
> # iwconfig
>
> no wirless extensions mit lo und eth0
>
> # iwlist scanning
>
> lo u. eth0 Interface doesn't support scanning
>
>
> Wäre schön wenn mir wer helfen könnte, Danke schön im voraus!
>
--
Einen Schönen Gruß,
Sigi
Reply to: