Re: externe USB-Platte
Am Samstag, 21. Juni 2008 13:47 schrieb Dirk Paul Finkeldey:
> Bernd Kloss wrote:
> >Etch
> >KDE 3.5.5
> >
> >Hallo,
> >
> > ich habe mehrere intakte 60 GB-2,5-Zoll Festplatten, die ich über USB an
> > den Linux-Server anschließe.
> >Die Platten sind mit einer primären Partition und FAT32 angelegt, damit
> > ich auch unter XP zugreifen kann.
> >
> >Wenn ich eine Platte anschließe, wird sie auch richtig erkannt.
> >
> >/dev/sdb5 on /media/disk type vfat
> >(rw,noexec,nosuid,nodev,noatime,uid=9011,utf8,shortname=lower)
> >
> >Fdisk meldet:
> >
> >Disk /dev/sda5: 59.9 GB, 59995160064 bytes
> >255 heads, 63 sectors/track, 7293 cylinders
> >Units = cylinders of 16065 * 512 = 8225280 bytes
> > Device Boot Start End Blocks Id System
> >
> >nichts.
> >Egal, ob ich die Platte als User mit KDE verwende oder sie als root von
> > Hand mounte.
> >Das Kopieren von Files geht meist. Häufig kommt die Meldung "verzögert"
> > und dann dauert es 3-4 Stunden bis 2 GB kopiert sind. Der Rechner ist im
> > Leerlauf.
> >Manchmal kann ich alte Dateien ohne Probleme köschen, manchmal lässt mich
> > die Maschine bestimmte Dateien nicht löschen, erst nach mehrfachem ab-
> > und anklemmen.
>
> Was sagen hwinfo und dmesg ?
>
> >Warum ist das das so und was kann ich dagegen machen?
>
> Könnte ein defect der Platten oder ein Problem mit dem Interface sein.
>
> > Danke für Tipps und Grüße
> >
> >Bernd Kloss
>
> Mit freundlichen Grüßen Dirk Finkeldey
Immer das gleich, egal, wie die Platte reagiert.
Bei dmesg kommen viele Fehlermeldungen, von denen ich nicht weiß, was sie
bedeuten, aber immer gleiches Muster, egal, welche der vier Platten ich
anhänge.
Gruß
Bernd
DMESG:
sb 4-6: new high speed USB device using ehci_hcd and address 3
usb 4-6: configuration #1 chosen from 1 choice
Initializing USB Mass Storage driver...
scsi1 : SCSI emulation for USB Mass Storage devices
usbcore: registered new driver usb-storage
USB Mass Storage support registered.
usb-storage: device found at 3
usb-storage: waiting for device to settle before scanning
Vendor: HTE54106 Model: 0G9AT00 Rev: 0811
Type: Direct-Access ANSI SCSI revision: 00
usb-storage: device scan complete
SCSI device sda: 117210240 512-byte hdwr sectors (60012 MB)
sda: test WP failed, assume Write Enabled
sda: assuming drive cache: write through
SCSI device sda: 117210240 512-byte hdwr sectors (60012 MB)
sda: test WP failed, assume Write Enabled
sda: assuming drive cache: write through
sda: sda1 < sda5 >
sd 1:0:0:0: Attached scsi disk sda
usb 4-6: reset high speed USB device using ehci_hcd and address 3
usb 4-6: USB disconnect, address 3
usb 4-6: new high speed USB device using ehci_hcd and address 4
usb 4-6: configuration #1 chosen from 1 choice
scsi2 : SCSI emulation for USB Mass Storage devices
usb-storage: device found at 4
usb-storage: waiting for device to settle before scanning
Vendor: HTE54106 Model: 0G9AT00 Rev: 0811
Type: Direct-Access ANSI SCSI revision: 00
SCSI device sdb: 117210240 512-byte hdwr sectors (60012 MB)
sdb: test WP failed, assume Write Enabled
sdb: assuming drive cache: write through
SCSI device sdb: 117210240 512-byte hdwr sectors (60012 MB)
sdb: test WP failed, assume Write Enabled
sdb: assuming drive cache: write through
sdb: sdb1 < sdb5 >
sd 2:0:0:0: Attached scsi disk sdb
usb-storage: device scan complete
scsi 1:0:0:0: rejecting I/O to dead device
scsi 1:0:0:0: rejecting I/O to dead device
...
FAT: Directory bread(block 57251) failed
scsi 1:0:0:0: rejecting I/O to dead device
*************************************************
HWINFO:
50: SCSI 200.0: 10600 Disk
[Created at block.218]
UDI: /org/freedesktop/Hal/devices/storage_serial_HTE54106_0G9AT00
Unique ID: aCV0.65vJnGtOb_E
Parent ID: f5xu.WfFmyaDsnJD
SysFS ID: /block/sdb
SysFS BusID: 2:0:0:0
SysFS Device
Link: /devices/pci0000:00/0000:00:10.3/usb4/4-6/4-6:1.0/host2/target2:0:0/2:0:0:0
Hardware Class: disk
Model: "HTE54106 0G9AT00"
Vendor: usb 0x05e3 "HTE54106"
Device: usb 0x0702 "0G9AT00"
Revision: "0811"
Driver: "usb-storage", "sd"
Driver Modules: "usb_storage"
Device File: /dev/sdb (/dev/sg0)
Device
Files: /dev/sdb, /dev/disk/by-id/usb-HTE54106_0G9AT00, /dev/disk/by-path/pci-0000:00:10.3-usb-0:6:1.0-scsi-0:0:0:0
Device Number: block 8:16-8:31 (char 21:0)
Features: Hotpluggable
Geometry (Logical): CHS 7296/255/63
Size: 117210240 sectors a 512 bytes
Speed: 480 Mbps
Module Alias: "usb:v05E3p0702d0033dc00dsc00dp00ic08isc06ip50"
Driver Info #0:
Driver Status: usb_storage is active
Driver Activation Cmd: "modprobe usb_storage"
Config Status: cfg=new, avail=yes, need=no, active=unknown
Attached to: #22 (USB Controller)
51: None 00.0: 11300 Partition
[Created at block.387]
UDI: /org/freedesktop/Hal/devices/volume_part1_size_1024
Unique ID: 6Kfz.SE1wIdpsiiC
Parent ID: aCV0.65vJnGtOb_E
SysFS ID: /block/sdb/sdb1
Hardware Class: partition
Model: "Partition"
Device File: /dev/sdb1
Device
Files: /dev/sdb1, /dev/disk/by-id/usb-HTE54106_0G9AT00-part1, /dev/disk/by-path/pci-0000:00:10.3-usb-0:6:1.0-scsi-0:0:0:0-part1
Config Status: cfg=new, avail=yes, need=no, active=unknown
Attached to: #50 (Disk)
52: None 00.0: 11300 Partition
[Created at block.387]
UDI: /org/freedesktop/Hal/devices/volume_uuid_47C9_77E9
Unique ID: w1gE.SE1wIdpsiiC
Parent ID: aCV0.65vJnGtOb_E
SysFS ID: /block/sdb/sdb5
Hardware Class: partition
Model: "Partition"
Device File: /dev/sdb5
Device
Files: /dev/sdb5, /dev/disk/by-id/usb-HTE54106_0G9AT00-part5, /dev/disk/by-path/pci-0000:00:10.3-usb-0:6:1.0-scsi-0:0:0:0-part5, /dev/disk/by-uuid/47C9-77E9
Config Status: cfg=new, avail=yes, need=no, active=unknown
Attached to: #50 (Disk)
Reply to: