cdrdao funktioniert nicht mehr
Da mit diesem Brenner, warum auch immer, nur cdrdao RWs brauchbar löscht und
dies jahrelang, aber sehr selten verwendet, funktioniert, hat, habe ich zur
Zeit ein Syntax-Problem, bei dem ich anstehe. Wie spreche ich den Brenner mit
"IDs" an und nicht mit hdx?
uname -r
2.6.15-1-686
/usr/local/bin/cdrecord-prodvd -s -scanbus dev=ATA
Cdrecord-ProDVD-Clone 2.01b31 (i686-pc-linux-gnu) Copyright (C) 1995-2004 J�g
Schilling
Unlocked features:
Limited features:
scsidev: 'ATA'
devname: 'ATA'
scsibus: -2 target: -2 lun: -2
Warning: Using badly designed ATAPI via /dev/hd* interface.
Linux sg driver version: 3.5.27
Using libscg version 'schily-0.8'.
...
scsibus1:
1,0,0 100) 'ATAPI ' 'CD-RW 48XMax ' '180D' Removable CD-ROM
1,1,0 101) *
1,2,0 102) *
1,3,0 103) *
1,4,0 104) *
1,5,0 105) *
1,6,0 106) *
1,7,0 107) *
/usr/bin/cdrdao blank --device ATA:1,0,0 --driver generic-mmc --blank-mode
full
Cdrdao version 1.1.9 - (C) Andreas Mueller <andreas@daneb.de>
SCSI interface library - (C) Joerg Schilling
Paranoia DAE library - (C) Monty
Check http://cdrdao.sourceforge.net/drives.html#dt for current driver tables.
ERROR: Cannot open SCSI device 'ATA:1,0,0': Cannot open '/dev/hda'
Supported SCSI transports for this platform:
Transport name: sg
Transport descr.: Generic transport independent SCSI
Transp. layer ind.:
Target specifier: bus,target,lun
Target example: 1,2,0
SCSI Bus scanning: supported
Open via UNIX device: not supported
Transport name: pg
Transport descr.: SCSI transport for ATAPI over Parallel Port
Transp. layer ind.:
Target specifier: bus,target,lun
Target example: 1,2,0
SCSI Bus scanning: supported
Open via UNIX device: not supported
Transport name: ATA
Transport descr.: ATA Packet specific SCSI transport
Transp. layer ind.: ATAPI:
Target specifier: bus,target,lun
Target example: ATAPI:1,2,0
SCSI Bus scanning: supported
Open via UNIX device: not supported
Transport name: ATA
Transport descr.: ATA Packet specific SCSI transport using sg interface
Transp. layer ind.: ATA:
Target specifier: bus,target,lun
Target example: 1,2,0
SCSI Bus scanning: supported
Open via UNIX device: not supported
ERROR: Please use option '--device [proto:]bus,id,lun', e.g. --device 0,6,0 or
--device ATAPI:0,0,0
ERROR: Cannot setup device ATA:1,0,0.
/usr/bin/cdrdao blank --device ATAPI:1,0,0 --driver generic-mmc --blank-mode
full
Cdrdao version 1.1.9 - (C) Andreas Mueller <andreas@daneb.de>
SCSI interface library - (C) Joerg Schilling
Paranoia DAE library - (C) Monty
Check http://cdrdao.sourceforge.net/drives.html#dt for current driver tables.
Using libscg version 'schily-0.8'
ATAPI:1,0,0: ATAPI CD-RW 48XMax Rev: 180D
Using driver: Generic SCSI-3/MMC - Version 2.0 (options 0x0000)
Blanking disk...
ERROR: Cannot erase CD-RW.
ERROR: Blanking failed.
/usr/bin/cdrdao blank --device /dev/hdc --driver generic-mmc --blank-mode full
Cdrdao version 1.1.9 - (C) Andreas Mueller <andreas@daneb.de>
SCSI interface library - (C) Joerg Schilling
Paranoia DAE library - (C) Monty
Check http://cdrdao.sourceforge.net/drives.html#dt for current driver tables.
Using libscg version 'schily-0.8'
/dev/hdc: ATAPI CD-RW 48XMax Rev: 180D
Using driver: Generic SCSI-3/MMC - Version 2.0 (options 0x0000)
Blanking disk...
Blanking time: 434 seconds
Al
Reply to: