Hallo, ich verwende etch mit 2.6.12-1-686, die Pakete sind auf dem Stand von heute, 09.01.06. Bei der Verwendung eines "Store 'n' Go" von Verbatim (512MB) läuft alles erst einmal sehr gut los: 8< --------------------------------------------------------------- >8 l305:~# tail -f /var/log/syslog usb 1-1: new high speed USB device using ehci_hcd and address 5 scsi2 : SCSI emulation for USB Mass Storage devices usb-storage: device found at 5 usb-storage: waiting for device to settle before scanning Vendor: VBTM Model: Store 'n' Go Rev: 1.04 Type: Direct-Access ANSI SCSI revision: 00 SCSI device sda: 1001472 512-byte hdwr sectors (513 MB) sda: Write Protect is off sda: Mode Sense: 23 00 00 00 sda: assuming drive cache: write through SCSI device sda: 1001472 512-byte hdwr sectors (513 MB) sda: Write Protect is off sda: Mode Sense: 23 00 00 00 sda: assuming drive cache: write through /dev/scsi/host2/bus0/target0/lun0: [CUMANA/ADFS] p1<5>Attached scsi removable disk sda at scsi2, channel 0, id 0, lun 0 usb-storage: device scan complete 8< --------------------------------------------------------------- >8 Dann jedoch endet es weniger schön: 8< --------------------------------------------------------------- >8 printk: 4 messages suppressed. Buffer I/O error on device sda1, logical block 508378384 Buffer I/O error on device sda1, logical block 508378384 Buffer I/O error on device sda1, logical block 508378412 last message repeated 5 times Buffer I/O error on device sda1, logical block 508378405 Buffer I/O error on device sda1, logical block 508378405 usb 1-1: USB disconnect, address 5 l305:~# 8< --------------------------------------------------------------- >8 Die Ausgabe von fdisk weist deutliche Fehlinterpretationen auf: 8< --------------------------------------------------------------- >8 l305:~# fdisk -l Disk /dev/hda: ... ... Partition table entries are not in disk order Disk /dev/sda: 512 MB, 512753664 bytes 16 heads, 32 sectors/track, 1956 cylinders Units = cylinders of 512 * 512 = 262144 bytes Device Boot Start End Blocks Id System /dev/sda1 * 1 1956 500720 e W95 FAT16 (LBA) Disk /dev/sda1: 2082.3 GB, 2082317979648 bytes 16 heads, 32 sectors/track, 7943412 cylinders Units = cylinders of 512 * 512 = 262144 bytes Device Boot Start End Blocks Id System /dev/sda1p1 * 1 1956 500720 e W95 FAT16 (LBA) l305:~# 8< --------------------------------------------------------------- >8 Solche Ausgaben gibt es auf diversen Mailing-Listen zu sehen, meist wird suggeriert, die Hardware wäre hinüber. Falls das stimmt, erkennen Knoppix und S.u.S.E. unter Verwendung von /dev/uba bzw. unter Vermeidung von udev den Stift korrekt, auch MS-Windows kann damit umgehen. Auch ein Hinweis[1], mit sfdisk die Partition-ID von 0xe auf 0x6 zu ändern brachte keinen Erfolg. Meine Suche u.a. in LKML ergab auch nichts. Kann mir bitte jemand sagen, was ich falsch mache oder übersehe? Ich stelle gern weitere Informationen zur Verfügung. [1] http://www.dclug.org.uk/archive/2005/04/msg00117.html -- Alexander Mader <alexander.mader@niles.de> GPG public key: http://mader.seppi.de/pubkey-dienst.asc
Attachment:
smime.p7s
Description: S/MIME Cryptographic Signature