AW: hde wird nicht erkannt
Hallo,
Ein paar Informationen habe ich noch.
Ich habe die dmesg Ausgaben vom knoppix24-boot und debian24-boot verglichen
und festgestellt, dass bei debian die Erkennung der IDE-Laufwerke vor der
Erkennung der Kontroller kommt.
Ausserdem vermisse ich beim debian boot den "Partition check".
Anbei die beiden dmesg-Ausgaben.
Kann die Reihenfolge beim Booten des Kernels irgendwo eingestellt werden?
Danke,
Robert
Linux version 2.4.27-ct-1 (root@debuild) (gcc version 3.3.4 (Debian 1:3.3.4-13)) #1 Sat Jan 15 16:14:04 UTC 2005
BIOS-provided physical RAM map:
BIOS-e820: 0000000000000000 - 000000000009e800 (usable)
BIOS-e820: 000000000009e800 - 00000000000a0000 (reserved)
BIOS-e820: 00000000000f0000 - 0000000000100000 (reserved)
BIOS-e820: 0000000000100000 - 0000000007ffd000 (usable)
BIOS-e820: 0000000007ffd000 - 0000000007fff000 (ACPI data)
BIOS-e820: 0000000007fff000 - 0000000008000000 (ACPI NVS)
BIOS-e820: 00000000ffff0000 - 0000000100000000 (reserved)
0MB HIGHMEM available.
127MB LOWMEM available.
On node 0 totalpages: 32765
zone(0): 4096 pages.
zone(1): 28669 pages.
zone(2): 0 pages.
ACPI disabled because your bios is from 98 and too old
You can enable it with acpi=force
Kernel command line: root=/dev/sda6 ro
Local APIC disabled by BIOS -- reenabling.
Found and enabled local APIC!
Initializing CPU#0
Detected 350.798 MHz processor.
Console: colour VGA+ 80x25
Calibrating delay loop... 699.59 BogoMIPS
Memory: 122952k/131060k available (1242k kernel code, 7716k reserved, 478k data, 120k init, 0k highmem)
Dentry cache hash table entries: 16384 (order: 5, 131072 bytes)
Inode cache hash table entries: 8192 (order: 4, 65536 bytes)
Mount cache hash table entries: 512 (order: 0, 4096 bytes)
Buffer cache hash table entries: 4096 (order: 2, 16384 bytes)
Page-cache hash table entries: 32768 (order: 5, 131072 bytes)
CPU: L1 I cache: 16K, L1 D cache: 16K
CPU: L2 cache: 512K
Intel machine check architecture supported.
Intel machine check reporting enabled on CPU#0.
CPU: After generic, caps: 0183fbff 00000000 00000000 00000000
CPU: Common caps: 0183fbff 00000000 00000000 00000000
CPU: Intel Pentium II (Deschutes) stepping 02
Enabling fast FPU save and restore... done.
Checking 'hlt' instruction... OK.
ACPI: IRQ9 SCI: Edge set to Level Trigger.
POSIX conformance testing by UNIFIX
enabled ExtINT on CPU#0
ESR value before enabling vector: 00000000
ESR value after enabling vector: 00000000
Using local APIC timer interrupts.
calibrating APIC timer ...
..... CPU clock speed is 350.7898 MHz.
..... host bus clock speed is 100.2252 MHz.
cpu: 0, clocks: 1002252, slice: 501126
CPU0<T0:1002240,T1:501104,D:10,S:501126,C:1002252>
mtrr: v1.40 (20010327) Richard Gooch (rgooch@atnf.csiro.au)
mtrr: detected mtrr type: Intel
ACPI: Subsystem revision 20040326
ACPI: Interpreter disabled.
PCI: PCI BIOS revision 2.10 entry at 0xf0750, last bus=1
PCI: Using configuration type 1
PCI: Probing PCI hardware
PCI: Probing PCI hardware (bus 00)
PCI: Using IRQ router PIIX/ICH [8086/7110] at 00:04.0
PCI: Found IRQ 5 for device 00:04.2
PCI: Sharing IRQ 5 with 00:06.0
Limiting direct PCI/PCI transfers.
Linux NET4.0 for Linux 2.4
Based upon Swansea University Computer Society NET3.039
Initializing RT netlink socket
apm: BIOS version 1.2 Flags 0x0b (Driver version 1.16)
Starting kswapd
VFS: Disk quotas vdquot_6.5.1
devfs: v1.12c (20020818) Richard Gooch (rgooch@atnf.csiro.au)
devfs: boot_options: 0x0
pty: 256 Unix98 ptys configured
Serial driver version 5.05c (2001-07-08) with HUB-6 MANY_PORTS MULTIPORT SHARE_IRQ SERIAL_PCI enabled
ttyS00 at 0x03f8 (irq = 4) is a 16550A
ttyS01 at 0x02f8 (irq = 3) is a 16550A
Real Time Clock Driver v1.10f
RAMDISK driver initialized: 16 RAM disks of 8192K size 1024 blocksize
Initializing Cryptographic API
NET4: Linux TCP/IP 1.0 for NET4.0
IP: routing cache hash table of 512 buckets, 4Kbytes
TCP: Hash tables configured (established 8192 bind 16384)
Linux IP multicast router 0.06 plus PIM-SM
RAMDISK: cramfs filesystem found at block 0
RAMDISK: Loading 4020 blocks [1 disk] into ram disk... |/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\done.
Freeing initrd memory: 4020k freed
VFS: Mounted root (cramfs filesystem).
Freeing unused kernel memory: 120k freed
NET4: Unix domain sockets 1.0/SMP for Linux NET4.0.
SCSI subsystem driver Revision: 1.00
PCI: Found IRQ 5 for device 00:06.0
PCI: Sharing IRQ 5 with 00:04.2
scsi0 : Adaptec AIC7XXX EISA/VLB/PCI SCSI HBA DRIVER, Rev 6.2.36
<Adaptec aic7890/91 Ultra2 SCSI adapter>
aic7890/91: Ultra2 Wide Channel A, SCSI Id=7, 32/253 SCBs
blk: queue c7ff3374, I/O limit 4095Mb (mask 0xffffffff)
(scsi0:A:0): 80.000MB/s transfers (40.000MHz, offset 15, 16bit)
Vendor: IBM Model: DDRS-39130D Rev: DC1B
Type: Direct-Access ANSI SCSI revision: 02
blk: queue c7ff3474, I/O limit 4095Mb (mask 0xffffffff)
scsi0:A:0:0: Tagged Queuing enabled. Depth 32
Attached scsi disk sda at scsi0, channel 0, id 0, lun 0
SCSI device sda: 17850000 512-byte hdwr sectors (9139 MB)
Partition check:
/dev/scsi/host0/bus0/target0/lun0: p2 < p5 p6 p7 p8 >
Journalled Block Device driver loaded
kjournald starting. Commit interval 5 seconds
EXT3-fs: mounted filesystem with ordered data mode.
kjournald starting. Commit interval 5 seconds
EXT3-fs: mounted filesystem with ordered data mode.
Adding Swap: 377488k swap-space (priority -1)
EXT3 FS 2.4-0.9.19, 19 August 2002 on sd(8,6), internal journal
Uniform Multi-Platform E-IDE driver Revision: 7.00beta4-2.4
ide: Assuming 33MHz system bus speed for PIO modes; override with idebus=xx
hda: WDC WD307AA-00BAA0, ATA DISK drive
hdb: TOSHIBA DVD-ROM SD-M1202, ATAPI CD/DVD-ROM drive
hdd: PLEXTOR CD-R PX-W1210A, ATAPI CD/DVD-ROM drive
ide0 at 0x1f0-0x1f7,0x3f6 on irq 14
ide1 at 0x170-0x177,0x376 on irq 15
hdb: attached ide-cdrom driver.
hdb: ATAPI 32X DVD-ROM drive, 256kB Cache
Uniform CD-ROM driver Revision: 3.12
hdd: attached ide-cdrom driver.
hdd: ATAPI 32X CD-ROM CD-R/RW drive, 2048kB Cache
hda: attached ide-disk driver.
hda: 60074784 sectors (30758 MB) w/2048KiB Cache, CHS=59598/16/63
/dev/ide/host0/bus0/target0/lun0: p2 p3 < p5 >
kjournald starting. Commit interval 5 seconds
EXT3 FS 2.4-0.9.19, 19 August 2002 on sd(8,8), internal journal
EXT3-fs: mounted filesystem with ordered data mode.
kjournald starting. Commit interval 5 seconds
EXT3 FS 2.4-0.9.19, 19 August 2002 on sd(8,7), internal journal
EXT3-fs: mounted filesystem with ordered data mode.
Linux agpgart interface v0.99 (c) Jeff Hartmann
agpgart: Maximum main memory to use for agp memory: 94M
agpgart: Detected Intel 440BX chipset
agpgart: AGP aperture is 64M @ 0xe4000000
dmfe: Davicom DM9xxx net driver, version 1.36.4 (2002-01-17)
PCI: Found IRQ 11 for device 00:0c.0
eth0: Davicom DM9102 at pci00:0c.0, 00:08:a1:2c:76:fb, irq 11.
PIIX4: IDE controller at PCI slot 00:04.1
PIIX4: chipset revision 1
PIIX4: not 100% native mode: will probe irqs later
ide0: BM-DMA at 0xd800-0xd807, BIOS settings: hda:DMA, hdb:DMA
ide1: BM-DMA at 0xd808-0xd80f, BIOS settings: hdc:pio, hdd:DMA
PDC20268: IDE controller at PCI slot 00:0a.0
PCI: Found IRQ 10 for device 00:0a.0
PDC20268: chipset revision 2
PDC20268: not 100% native mode: will probe irqs later
ide2: BM-DMA at 0xa400-0xa407, BIOS settings: hde:pio, hdf:pio
ide3: BM-DMA at 0xa408-0xa40f, BIOS settings: hdg:pio, hdh:pio
scsi1 : SCSI host adapter emulation for IDE ATAPI devices
usb.c: registered new driver usbdevfs
usb.c: registered new driver hub
usb-uhci.c: $Revision: 1.275 $ time 16:28:01 Jan 15 2005
usb-uhci.c: High bandwidth mode enabled
PCI: Found IRQ 5 for device 00:04.2
PCI: Sharing IRQ 5 with 00:06.0
usb-uhci.c: USB UHCI at I/O 0xd400, IRQ 5
usb-uhci.c: Detected 2 ports
usb.c: new USB bus registered, assigned bus number 1
hub.c: USB hub found
hub.c: 2 ports detected
usb-uhci.c: v1.275:USB Universal Host Controller Interface driver
Linux Tulip driver version 0.9.15-pre12 (Aug 9, 2002)
uhci.c: USB Universal Host Controller Interface driver v1.1
Linux version 2.4.23-xfs (root@Knoppix) (gcc version 2.95.4 20011002 (Debian prerelease)) #1 SMP Mi Dez 10 22:25:03 CET 2003
BIOS-provided physical RAM map:
BIOS-e820: 0000000000000000 - 000000000009e800 (usable)
BIOS-e820: 000000000009e800 - 00000000000a0000 (reserved)
BIOS-e820: 00000000000f0000 - 0000000000100000 (reserved)
BIOS-e820: 0000000000100000 - 0000000007ffd000 (usable)
BIOS-e820: 0000000007ffd000 - 0000000007fff000 (ACPI data)
BIOS-e820: 0000000007fff000 - 0000000008000000 (ACPI NVS)
BIOS-e820: 00000000ffff0000 - 0000000100000000 (reserved)
0MB HIGHMEM available.
127MB LOWMEM available.
On node 0 totalpages: 32765
zone(0): 4096 pages.
zone(1): 28669 pages.
zone(2): 0 pages.
ACPI disabled because your bios is from 98 and too old
You can enable it with acpi=force
Kernel command line: ramdisk_size=100000 init=/etc/init lang=de apm=power-off hda=scsi hdb=scsi hdc=scsi hdd=scsi hde=scsi hdf=scsi hdg=scsi hdh=scsi vga=791 initrd=minirt24.gz nomce quiet BOOT_IMAGE=knoppix BOOT_IMAGE=linux24
ide_setup: hda=scsi
ide_setup: hdb=scsi
ide_setup: hdc=scsi
ide_setup: hdd=scsi
ide_setup: hde=scsi
ide_setup: hdf=scsi
ide_setup: hdg=scsi
ide_setup: hdh=scsi
Local APIC disabled by BIOS -- reenabling.
Found and enabled local APIC!
Initializing CPU#0
Detected 350.803 MHz processor.
Console: colour dummy device 80x25
Calibrating delay loop... 699.59 BogoMIPS
Memory: 125948k/131060k available (1278k kernel code, 4720k reserved, 547k data, 136k init, 0k highmem)
Dentry cache hash table entries: 16384 (order: 5, 131072 bytes)
Inode cache hash table entries: 8192 (order: 4, 65536 bytes)
Mount cache hash table entries: 512 (order: 0, 4096 bytes)
Buffer cache hash table entries: 4096 (order: 2, 16384 bytes)
Page-cache hash table entries: 32768 (order: 5, 131072 bytes)
CPU: L1 I cache: 16K, L1 D cache: 16K
CPU: L2 cache: 512K
CPU: After generic, caps: 0183fbff 00000000 00000000 00000000
CPU: Common caps: 0183fbff 00000000 00000000 00000000
Enabling fast FPU save and restore... done.
Checking 'hlt' instruction... OK.
Checking for popad bug... OK.
POSIX conformance testing by UNIFIX
mtrr: v1.40 (20010327) Richard Gooch (rgooch@atnf.csiro.au)
mtrr: detected mtrr type: Intel
CPU: L1 I cache: 16K, L1 D cache: 16K
CPU: L2 cache: 512K
CPU: After generic, caps: 0183fbff 00000000 00000000 00000000
CPU: Common caps: 0183fbff 00000000 00000000 00000000
CPU0: Intel Pentium II (Deschutes) stepping 02
per-CPU timeslice cutoff: 1463.72 usecs.
SMP motherboard not detected.
enabled ExtINT on CPU#0
ESR value before enabling vector: 00000000
ESR value after enabling vector: 00000000
Using local APIC timer interrupts.
calibrating APIC timer ...
..... CPU clock speed is 350.7930 MHz.
..... host bus clock speed is 100.2262 MHz.
cpu: 0, clocks: 1002262, slice: 501131
CPU0<T0:1002256,T1:501120,D:5,S:501131,C:1002262>
Waiting on wait_init_idle (map = 0x0)
All processors have done init_idle
PCI: PCI BIOS revision 2.10 entry at 0xf0750, last bus=1
PCI: Using configuration type 1
PCI: Probing PCI hardware
PCI: Probing PCI hardware (bus 00)
PCI: Using IRQ router PIIX/ICH [8086/7110] at 00:04.0
PCI: Found IRQ 5 for device 00:04.2
PCI: Sharing IRQ 5 with 00:06.0
Limiting direct PCI/PCI transfers.
isapnp: Scanning for PnP cards...
isapnp: No Plug & Play device found
Linux NET4.0 for Linux 2.4
Based upon Swansea University Computer Society NET3.039
Initializing RT netlink socket
Starting kswapd
VFS: Disk quotas vdquot_6.5.1
vesafb: framebuffer at 0xe3000000, mapped to 0xc880d000, size 3072k
vesafb: mode is 1024x768x16, linelength=2048, pages=0
vesafb: protected mode interface info at c000:041a
vesafb: scrolling: redraw
vesafb: directcolor: size=0:5:6:5, shift=0:11:5:0
Console: switching to colour frame buffer device 128x48
fb0: VESA VGA frame buffer device
pty: 256 Unix98 ptys configured
Floppy drive(s): fd0 is 1.44M
FDC 0 is a post-1991 82077
RAMDISK driver initialized: 16 RAM disks of 100000K size 1024 blocksize
Uniform Multi-Platform E-IDE driver Revision: 7.00beta4-2.4
ide: Assuming 33MHz system bus speed for PIO modes; override with idebus=xx
PIIX4: IDE controller at PCI slot 00:04.1
PIIX4: chipset revision 1
PIIX4: not 100% native mode: will probe irqs later
ide0: BM-DMA at 0xd800-0xd807, BIOS settings: hda:DMA, hdb:DMA
ide1: BM-DMA at 0xd808-0xd80f, BIOS settings: hdc:pio, hdd:DMA
PDC20268: IDE controller at PCI slot 00:0a.0
PCI: Found IRQ 10 for device 00:0a.0
PDC20268: chipset revision 2
PDC20268: not 100% native mode: will probe irqs later
ide2: BM-DMA at 0xa400-0xa407, BIOS settings: hde:pio, hdf:pio
ide3: BM-DMA at 0xa408-0xa40f, BIOS settings: hdg:pio, hdh:pio
hda: WDC WD307AA-00BAA0, ATA DISK drive
hdb: TOSHIBA DVD-ROM SD-M1202, ATAPI CD/DVD-ROM drive
hdd: PLEXTOR CD-R PX-W1210A, ATAPI CD/DVD-ROM drive
hde: Maxtor 6B200P0, ATA DISK drive
ide0 at 0x1f0-0x1f7,0x3f6 on irq 14
ide1 at 0x170-0x177,0x376 on irq 15
ide2 at 0xb800-0xb807,0xb402 on irq 10
hda: attached ide-disk driver.
hda: host protected area => 1
hda: 60074784 sectors (30758 MB) w/2048KiB Cache, CHS=3739/255/63
hde: attached ide-disk driver.
hde: host protected area => 1
hde: 398297088 sectors (203928 MB) w/8192KiB Cache, CHS=24792/255/63
ide-cd: passing drive hdb to ide-scsi emulation.
ide-cd: passing drive hdd to ide-scsi emulation.
hdb: attached ide-scsi driver.
hdd: attached ide-scsi driver.
Partition check:
hda: hda2 hda3 < hda5 >
hde: hde1 < hde5 hde6 >
ide: late registration of driver.
Promise Fasttrak(tm) Softwareraid driver 0.03beta: No raid array found
Highpoint HPT370 Softwareraid driver for linux version 0.02
Guestimating sector 60073759 for superblock
Guestimating sector 398267159 for superblock
driver for Silicon Image(tm) Medley(tm) hardware version 0.0.1: No raid array found
SCSI subsystem driver Revision: 1.00
scsi0 : SCSI host adapter emulation for IDE ATAPI devices
Vendor: TOSHIBA Model: DVD-ROM SD-M1202 Rev: 1020
Type: CD-ROM ANSI SCSI revision: 02
Vendor: PLEXTOR Model: CD-R PX-W1210A Rev: 1.01
Type: CD-ROM ANSI SCSI revision: 02
Attached scsi CD-ROM sr0 at scsi0, channel 0, id 0, lun 0
Attached scsi CD-ROM sr1 at scsi0, channel 0, id 1, lun 0
sr0: scsi3-mmc drive: 32x/32x cd/rw xa/form2 cdda tray
Uniform CD-ROM driver Revision: 3.12
sr1: scsi3-mmc drive: 32x/32x writer cd/rw xa/form2 cdda tray
Initializing Cryptographic API
NET4: Linux TCP/IP 1.0 for NET4.0
IP Protocols: ICMP, UDP, TCP, IGMP
IP: routing cache hash table of 512 buckets, 4Kbytes
TCP: Hash tables configured (established 8192 bind 8192)
NET4: Unix domain sockets 1.0/SMP for Linux NET4.0.
RAMDISK: Compressed image found at block 0
Freeing initrd memory: 717k freed
EXT2-fs warning: checktime reached, running e2fsck is recommended
VFS: Mounted root (ext2 filesystem).
kmod: failed to exec /sbin/modprobe -s -k sysfs, errno = 2
PCI: Found IRQ 5 for device 00:06.0
PCI: Sharing IRQ 5 with 00:04.2
scsi1 : Adaptec AIC7XXX EISA/VLB/PCI SCSI HBA DRIVER, Rev 6.2.36
<Adaptec aic7890/91 Ultra2 SCSI adapter>
aic7890/91: Ultra2 Wide Channel A, SCSI Id=7, 32/253 SCBs
(scsi1:A:0): 80.000MB/s transfers (40.000MHz, offset 15, 16bit)
Vendor: IBM Model: DDRS-39130D Rev: DC1B
Type: Direct-Access ANSI SCSI revision: 02
scsi1:A:0:0: Tagged Queuing enabled. Depth 253
Attached scsi disk sda at scsi1, channel 0, id 0, lun 0
SCSI device sda: 17850000 512-byte hdwr sectors (9139 MB)
sda: sda2 < sda5 sda6 sda7 sda8 >
NCR53c406a: no available ports found
aec671x_detect:
PCI: Enabling device 00:06.0 (0016 -> 0017)
PCI: Found IRQ 5 for device 00:06.0
PCI: Sharing IRQ 5 with 00:04.2
scsi1: PCI error Interrupt at seqaddr = 0x9
scsi1: Signaled a Target Abort
scsi: <fdomain> Detection failed (no card)
GDT: Storage RAID Controller Driver. Version: 2.05
GDT: Found 0 PCI Storage RAID Controllers
megaraid: v1.18k (Release Date: Thu Aug 28 10:05:11 EDT 2003)
megaraid: no BIOS enabled.
DC390: 0 adapters found
Failed initialization of WD-7000 SCSI card!
usb.c: registered new driver usbdevfs
usb.c: registered new driver hub
usb-uhci.c: $Revision: 1.275 $ time 22:39:59 Dec 10 2003
usb-uhci.c: High bandwidth mode enabled
PCI: Found IRQ 5 for device 00:04.2
PCI: Sharing IRQ 5 with 00:06.0
usb-uhci.c: USB UHCI at I/O 0xd400, IRQ 5
usb-uhci.c: Detected 2 ports
usb.c: new USB bus registered, assigned bus number 1
hub.c: USB hub found
hub.c: 2 ports detected
usb-uhci.c: v1.275:USB Universal Host Controller Interface driver
Initializing USB Mass Storage driver...
usb.c: registered new driver usb-storage
USB Mass Storage support registered.
blk: queue c033ec00, I/O limit 4095Mb (mask 0xffffffff)
blk: queue c033f4d8, I/O limit 4095Mb (mask 0xffffffff)
ISO 9660 Extensions: Microsoft Joliet Level 3
kmod: failed to exec /sbin/modprobe -s -k nls_iso8859-1, errno = 2
kmod: failed to exec /sbin/modprobe -s -k nls_iso8859-1, errno = 2
ISO 9660 Extensions: RRIP_1991A
cloop: Initializing cloop v2.00
cloop: /cdrom/KNOPPIX/KNOPPIX: 29683 blocks, 65536 bytes/block, largest block is 65562 bytes.
cloop: loaded (max 8 devices)
ISO 9660 Extensions: RRIP_1991A
Freeing unused kernel memory: 136k freed
Real Time Clock Driver v1.10e
apm: BIOS version 1.2 Flags 0x0b (Driver version 1.16)
Linux Kernel Card Services 3.1.22
options: [pci] [cardbus] [pm]
Intel ISA PCIC probe: not found.
Databook TCIC-2 PCMCIA probe: not found.
usbdevfs: remount parameter error
uhci.c: USB Universal Host Controller Interface driver v1.1
Serial driver version 5.05c (2001-07-08) with MANY_PORTS SHARE_IRQ SERIAL_PCI ISAPNP enabled
ttyS00 at 0x03f8 (irq = 4) is a 16550A
ttyS01 at 0x02f8 (irq = 3) is a 16550A
parport0: PC-style at 0x378 (0x778) [PCSPP,TRISTATE,EPP]
parport0: irq 7 detected
dmfe: Davicom DM9xxx net driver, version 1.36.4 (2002-01-17)
PCI: Found IRQ 11 for device 00:0c.0
eth0: Davicom DM9102 at pci00:0c.0, 00:08:a1:2c:76:fb, irq 11.
Linux agpgart interface v0.99 (c) Jeff Hartmann
agpgart: Maximum main memory to use for agp memory: 94M
agpgart: Detected Intel 440BX chipset
agpgart: AGP aperture is 64M @ 0xe4000000
FAT: Did not find valid FSINFO signature.
Found signature1 0xea4c29fa signature2 0x2a3b0872 sector=20148.
VFS: Can't find a valid FAT filesystem on dev 03:02.
FAT: Did not find valid FSINFO signature.
Found signature1 0xea4c29fa signature2 0x2a3b0872 sector=20148.
VFS: Can't find a valid FAT filesystem on dev 03:02.
NTFS driver v1.1.22 [Flags: R/W MODULE]
Adding Swap: 377488k swap-space (priority -1)
Reply to: