Re: Problene beim Einbau einer 3. Netzwerkkarte
Am Fr, den 26.11.2004 schrieb Gernot Galli um 18:55:
> Hier noch die Ausgabe von lspci und dmseg | grep eth
> lspci gibt folgendes aus
>
> 00:09.0 Ethernet controller: VIA Technologies, Inc.: Unknown device 3106
> (rev 8b)
> Subsystem: VIA Technologies, Inc.: Unknown device 0105
> Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop-
> ParErr- Stepp
> Status: Cap+ 66Mhz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort-
> <TAbort-
> Latency: 32 (750ns min, 2000ns max), cache line size 08
> Interrupt: pin A routed to IRQ 11
> Region 0: I/O ports at e400 [size=256]
> Region 1: Memory at dea00000 (32-bit, non-prefetchable)
> [size=256]
> Capabilities: [44] Power Management version 2
> Flags: PMEClk- DSI- D1+ D2+ AuxCurrent=0mA PME(D0+,D1
> +,D2+,D3hot+
> Status: D0 PME-Enable- DSel=0 DScale=0 PME-
>
> 00:0b.0 Ethernet controller: Realtek Semiconductor Co., Ltd.
> RTL-8029(AS)
> Control: I/O+ Mem+ BusMaster- SpecCycle- MemWINV- VGASnoop-
> ParErr- Stepp
> Status: Cap- 66Mhz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort-
> <TAbort-
> Interrupt: pin A routed to IRQ 12
> Region 0: I/O ports at e800 [size=32]
>
> 00:11.0 Ethernet controller: VIA Technologies, Inc.: Unknown device 3106
> (rev 8b)
> Subsystem: VIA Technologies, Inc.: Unknown device 0105
> Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop-
> ParErr- Stepp
> Status: Cap+ 66Mhz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort-
> <TAbort-
> Latency: 32 (750ns min, 2000ns max), cache line size 08
> Interrupt: pin A routed to IRQ 11
> Region 0: I/O ports at ec00 [size=256]
> Region 1: Memory at dea01000 (32-bit, non-prefetchable)
> [size=256]
> Capabilities: [44] Power Management version 2
> Flags: PMEClk- DSI- D1+ D2+ AuxCurrent=0mA PME(D0+,D1
> +,D2+,D3hot+
> Status: D0 PME-Enable- DSel=0 DScale=0 PME-
>
> dmseg | grep eth:
>
> eth0: RealTek RTL-8029 found at 0xe800, IRQ 12, 00:E0:7D:77:26:5E.
> eth1: VIA VT6105 Rhine-III at 0xdea00000, 00:40:f4:b1:59:37, IRQ 11.
> eth1: MII PHY found at address 1, status 0x7869 advertising 05e1 Link
> 41e1.
> eth2: VIA VT6105 Rhine-III at 0xdea01000, 00:40:f4:b1:4a:93, IRQ 11.
> eth2: MII PHY found at address 1, status 0x7869 advertising 05e1 Link
[...]
Gernot,
beide VIA-Karten nutzen IRQ11. Das kann, muss aber nicht, ein Problem
sein. (Empfehlung: Evtl. Steckpl. aendern, BIOS
Einstellung/Systemkonfiguration anpassen)
dmesg lieferte Dir die Zugehörigkeit der Mac-Adresse zur jeweiligen
Karte wie z.B. eth1 hat MAC Adresse 00:40:f4:b1:59:37
Welche MAC Adresse mit welcher IP-Adresse korresponiert kannst Du
Ueberpruefen mit arp
arp 192.168.10.1 sollte liefern: 00:40:f4:b1:59:37
arp 192.168.20.1 sollte liefern: 00:40:f4:b1:4a:93
Schoene Gruesse aus der Lueneburger Heide
Werner
Reply to: