sil 3112: hardware raid oder software raid?
Hallo,
ich versuche verzweifelt, bei meinem Board
(Gigabyte GA-7N400 Pro2 mit SIL 3112 SATA-RAID)
ein raid aufzusetzen.
Mein System erkennt meine zwei SATA-Platten
als /dev/sda und /dev/sdb. Im Bios habe ich
Raid1 eingestellt und eine der Platten
gespiegelt (Das Bios bietet dafuer eine
Option, dann wird aus der zweiten Platte
eine exakte Kopie der ersten).
Leider werden trotzdem beide Platten von System
behandelt wie zwei SCSI-Platten. Wenn ich auf
/dev/sdaX was aendere, zieht die entsprechende
Partition auf /dev/sdbX nicht automatisch mit.
Ich verwende Kernel 2.6.8-1-k7 mit einer aktuellen
Sarge.
Waere schoen, wenn mir jemand sagen koennte, wie
ich diesen Raid-Controller nutzen kann. Ist es
nun eigentlich ein Hardware-Raid oder ein Software
Raid? Wenn Hardware, warum sehe ich dann 2 Platten?
Danke im Voraus.
Martin
Hier noch ein paar Zusatz-Informationen (lsmod/lcpci/uname/dmesg):
martin@raidinstall:~$ sudo lsmod
Module Size Used by
raid1 17536 0
md 49544 1 raid1
ipv6 262340 8
amd74xx 14108 1
shpchp 100780 0
pciehp 97388 0
pci_hotplug 34352 2 shpchp,pciehp
snd_intel8x0 36140 0
snd_ac97_codec 69572 1 snd_intel8x0
snd_pcm 97480 1 snd_intel8x0
snd_timer 25540 1 snd_pcm
snd_page_alloc 11720 2 snd_intel8x0,snd_pcm
snd_mpu401_uart 8000 1 snd_intel8x0
snd_rawmidi 25380 1 snd_mpu401_uart
snd_seq_device 8264 1 snd_rawmidi
snd 57380 7
snd_intel8x0,snd_ac97_codec,snd_pcm,snd_timer,snd_mpu401_uart,snd_rawmidi,snd_seq_device
tsdev 7360 0
mousedev 10444 1
joydev 9856 0
usbhid 32000 0
ohci_hcd 21380 0
nvidia_agp 7836 1
agpgart 34536 1 nvidia_agp
analog 11872 0
gameport 4736 2 snd_intel8x0,analog
parport_pc 35328 0
parport 41544 1 parport_pc
floppy 60304 0
pcspkr 3688 0
evdev 9600 0
ehci_hcd 31364 0
usbcore 118308 5 usbhid,ohci_hcd,ehci_hcd
i810_audio 37204 0
ac97_codec 18700 1 i810_audio
soundcore 10400 2 snd,i810_audio
r8169 17604 0
crc32 4352 1 r8169
capability 4616 0
commoncap 7296 1 capability
ide_generic 1472 0
ide_cd 42528 0
ide_core 138788 3 amd74xx,ide_generic,ide_cd
cdrom 40284 1 ide_cd
rtc 12728 0
ext2 71720 1
ext3 126760 2
jbd 61784 1 ext3
mbcache 9220 2 ext2,ext3
sd_mod 21632 5
sata_sil 8004 4
libata 41348 1 sata_sil
scsi_mod 124620 2 sd_mod,libata
unix 28596 114
font 8448 0
vesafb 6688 0
cfbcopyarea 3776 1 vesafb
cfbimgblt 3072 1 vesafb
cfbfillrect 3712 1 vesafb
martin@raidinstall:~$ sudo lspci
0000:00:00.0 Host bridge: nVidia Corporation nForce2 AGP (different
version?) (rev c1)
0000:00:00.1 RAM memory: nVidia Corporation nForce2 Memory Controller 1 (rev
c1)
0000:00:00.2 RAM memory: nVidia Corporation nForce2 Memory Controller 4 (rev
c1)
0000:00:00.3 RAM memory: nVidia Corporation nForce2 Memory Controller 3 (rev
c1)
0000:00:00.4 RAM memory: nVidia Corporation nForce2 Memory Controller 2 (rev
c1)
0000:00:00.5 RAM memory: nVidia Corporation nForce2 Memory Controller 5 (rev
c1)
0000:00:01.0 ISA bridge: nVidia Corporation nForce2 ISA Bridge (rev a4)
0000:00:01.1 SMBus: nVidia Corporation nForce2 SMBus (MCP) (rev a2)
0000:00:02.0 USB Controller: nVidia Corporation nForce2 USB Controller (rev
a4)
0000:00:02.1 USB Controller: nVidia Corporation nForce2 USB Controller (rev
a4)
0000:00:02.2 USB Controller: nVidia Corporation nForce2 USB Controller (rev
a4)
0000:00:06.0 Multimedia audio controller: nVidia Corporation nForce2 AC97
Audio Controler (MCP) (rev a1)
0000:00:08.0 PCI bridge: nVidia Corporation nForce2 External PCI Bridge (rev
a3)
0000:00:09.0 IDE interface: nVidia Corporation nForce2 IDE (rev a2)
0000:00:1e.0 PCI bridge: nVidia Corporation nForce2 AGP (rev c1)
0000:01:0b.0 Ethernet controller: Realtek Semiconductor Co., Ltd. RTL-8169
Gigabit Ethernet (rev 10)
0000:01:0d.0 RAID bus controller: Silicon Image, Inc. (formerly CMD
Technology Inc) SiI 3512 [SATALink/SATARaid] Serial ATA Controller (rev 01)
0000:02:00.0 VGA compatible controller: nVidia Corporation NV34 [GeForce FX
5200] (rev a1)
martin@raidinstall:~$ sudo fdisk -l /dev/sd?
Disk /dev/sda: 82.3 GB, 82348277760 bytes
255 heads, 63 sectors/track, 10011 cylinders
Units = cylinders of 16065 * 512 = 8225280 bytes
Device Boot Start End Blocks Id System
/dev/sda1 * 1 4 32098+ 83 Linux
/dev/sda2 5 10011 80381227+ 5 Extended
/dev/sda5 5 1220 9767488+ 83 Linux
/dev/sda6 1221 7299 48829536 83 Linux
/dev/sda7 7300 7548 2000061 82 Linux swap
/dev/sda8 7549 10011 19784016 83 Linux
Disk /dev/sdb: 82.3 GB, 82348277760 bytes
255 heads, 63 sectors/track, 10011 cylinders
Units = cylinders of 16065 * 512 = 8225280 bytes
Device Boot Start End Blocks Id System
/dev/sdb1 * 1 4 32098+ 83 Linux
/dev/sdb2 5 10011 80381227+ 5 Extended
/dev/sdb5 5 1220 9767488+ 83 Linux
/dev/sdb6 1221 7299 48829536 83 Linux
/dev/sdb7 7300 7548 2000061 82 Linux swap
/dev/sdb8 7549 10011 19784016 83 Linux
martin@raidinstall:~$ uname -a
Linux raidinstall 2.6.8-1-k7 #1 Sat Aug 28 13:44:52 EDT 2004 i686 GNU/Linux
martin@raidinstall:~$ dmesg
24k reserved, 694k data, 148k init, 131008k highmem)
Checking if this processor honours the WP bit even in supervisor mode... Ok.
Calibrating delay loop... 3792.89 BogoMIPS
Security Scaffold v1.0.0 initialized
Mount-cache hash table entries: 512 (order: 0, 4096 bytes)
CPU: After generic identify, caps: 0383fbff c1c3fbff 00000000 00000000
CPU: After vendor identify, caps: 0383fbff c1c3fbff 00000000 00000000
CPU: L1 I Cache: 64K (64 bytes/line), D cache 64K (64 bytes/line)
CPU: L2 Cache: 512K (64 bytes/line)
CPU: After all inits, caps: 0383fbff c1c3fbff 00000000 00000020
Intel machine check architecture supported.
Intel machine check reporting enabled on CPU#0.
CPU: AMD Athlon(tm) XP 2600+ stepping 00
Enabling fast FPU save and restore... done.
Enabling unmasked SIMD FPU exception support... done.
Checking 'hlt' instruction... OK.
enabled ExtINT on CPU#0
ESR value before enabling vector: 00000000
ESR value after enabling vector: 00000000
ENABLING IO-APIC IRQs
init IO_APIC IRQs
IO-APIC (apicid-pin) 2-0, 2-16, 2-17, 2-18, 2-19, 2-20, 2-21, 2-22, 2-23
not connected.
..TIMER: vector=0x31 pin1=2 pin2=-1
..MP-BIOS bug: 8254 timer not connected to IO-APIC
...trying to set up timer (IRQ0) through the 8259A ... failed.
...trying to set up timer as Virtual Wire IRQ... failed.
...trying to set up timer as ExtINT IRQ... works.
Using local APIC timer interrupts.
calibrating APIC timer ...
..... CPU clock speed is 1912.0829 MHz.
..... host bus clock speed is 332.0665 MHz.
checking if image is initramfs...it isn't (ungzip failed); looks like an
initrd
Freeing initrd memory: 4592k freed
NET: Registered protocol family 16
PCI: PCI BIOS revision 2.10 entry at 0xfaf70, last bus=2
PCI: Using configuration type 1
mtrr: v2.0 (20020519)
ACPI: Subsystem revision 20040326
ACPI: Interpreter enabled
ACPI: Using IOAPIC for interrupt routing
ACPI: PCI Root Bridge [PCI0] (00:00)
PCI: Probing PCI hardware (bus 00)
ACPI: PCI Interrupt Routing Table [\_SB_.PCI0._PRT]
ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.HUB0._PRT]
ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.AGPB._PRT]
ACPI: PCI Interrupt Link [LNK1] (IRQs 3 4 5 6 7 9 *10 11 12 14 15)
ACPI: PCI Interrupt Link [LNK2] (IRQs 3 4 5 6 7 9 10 11 12 14 15) *0,
disabled.
ACPI: PCI Interrupt Link [LNK3] (IRQs 3 4 5 6 7 9 10 *11 12 14 15)
ACPI: PCI Interrupt Link [LNK4] (IRQs 3 4 *5 6 7 9 10 11 12 14 15)
ACPI: PCI Interrupt Link [LNK5] (IRQs 3 4 5 6 7 9 10 11 12 14 15) *0,
disabled.
ACPI: PCI Interrupt Link [LUBA] (IRQs 3 4 *5 6 7 9 10 11 12 14 15)
ACPI: PCI Interrupt Link [LUBB] (IRQs 3 4 5 6 7 9 *10 11 12 14 15)
ACPI: PCI Interrupt Link [LMAC] (IRQs 3 4 5 6 7 9 10 11 12 14 15) *0,
disabled.
ACPI: PCI Interrupt Link [LAPU] (IRQs 3 4 5 6 7 9 10 11 12 14 15) *0,
disabled.
ACPI: PCI Interrupt Link [LACI] (IRQs 3 4 5 6 7 *9 10 11 12 14 15)
ACPI: PCI Interrupt Link [LMCI] (IRQs 3 4 5 6 7 9 10 11 12 14 15) *0,
disabled.
ACPI: PCI Interrupt Link [LSMB] (IRQs 3 4 5 6 7 *9 10 11 12 14 15)
ACPI: PCI Interrupt Link [LUB2] (IRQs 3 4 5 6 7 9 10 *11 12 14 15)
ACPI: PCI Interrupt Link [LFIR] (IRQs 3 4 5 6 7 9 10 11 12 14 15) *0,
disabled.
ACPI: PCI Interrupt Link [L3CM] (IRQs 3 4 5 6 7 9 10 11 12 14 15) *0,
disabled.
ACPI: PCI Interrupt Link [LIDE] (IRQs 3 4 5 6 7 9 10 11 12 14 15) *0,
disabled.
ACPI: PCI Interrupt Link [APC1] (IRQs *16), disabled.
ACPI: PCI Interrupt Link [APC2] (IRQs *17), disabled.
ACPI: PCI Interrupt Link [APC3] (IRQs *18), disabled.
ACPI: PCI Interrupt Link [APC4] (IRQs *19), disabled.
ACPI: PCI Interrupt Link [APC5] (IRQs *16), disabled.
ACPI: PCI Interrupt Link [APCF] (IRQs 20 21 22) *0, disabled.
ACPI: PCI Interrupt Link [APCG] (IRQs 20 21 22) *0, disabled.
ACPI: PCI Interrupt Link [APCH] (IRQs 20 21 22) *0, disabled.
ACPI: PCI Interrupt Link [APCI] (IRQs 20 21 22) *0, disabled.
ACPI: PCI Interrupt Link [APCJ] (IRQs 20 21 22) *0, disabled.
ACPI: PCI Interrupt Link [APCK] (IRQs 20 21 22) *0, disabled.
ACPI: PCI Interrupt Link [APCS] (IRQs *23), disabled.
ACPI: PCI Interrupt Link [APCL] (IRQs 20 21 22) *0, disabled.
ACPI: PCI Interrupt Link [APCM] (IRQs 20 21 22) *0, disabled.
ACPI: PCI Interrupt Link [AP3C] (IRQs 20 21 22) *0, disabled.
ACPI: PCI Interrupt Link [APCZ] (IRQs 20 21 22) *0, disabled.
Linux Plug and Play Support v0.97 (c) Adam Belay
PnPBIOS: Scanning system for PnP BIOS support...
PnPBIOS: Found PnP BIOS installation structure at 0xc00fb9d0
PnPBIOS: PnP BIOS version 1.0, entry 0xf0000:0xba00, dseg 0xf0000
PnPBIOS: 15 nodes reported by PnP BIOS; 15 recorded by driver
PCI: Using ACPI for IRQ routing
ACPI: PCI Interrupt Link [APCS] enabled at IRQ 23
ACPI: PCI interrupt 0000:00:01.1[A] -> GSI 23 (level, high) -> IRQ 169
ACPI: PCI Interrupt Link [APCF] enabled at IRQ 22
ACPI: PCI interrupt 0000:00:02.0[A] -> GSI 22 (level, high) -> IRQ 177
ACPI: PCI Interrupt Link [APCG] enabled at IRQ 21
ACPI: PCI interrupt 0000:00:02.1[B] -> GSI 21 (level, high) -> IRQ 185
ACPI: PCI Interrupt Link [APCL] enabled at IRQ 20
ACPI: PCI interrupt 0000:00:02.2[C] -> GSI 20 (level, high) -> IRQ 193
ACPI: PCI Interrupt Link [APCJ] enabled at IRQ 22
ACPI: PCI interrupt 0000:00:06.0[A] -> GSI 22 (level, high) -> IRQ 177
ACPI: PCI Interrupt Link [APC1] enabled at IRQ 16
ACPI: PCI interrupt 0000:01:0b.0[A] -> GSI 16 (level, high) -> IRQ 201
ACPI: PCI Interrupt Link [APC3] enabled at IRQ 18
ACPI: PCI interrupt 0000:01:0d.0[A] -> GSI 18 (level, high) -> IRQ 209
ACPI: PCI Interrupt Link [APC4] enabled at IRQ 19
ACPI: PCI interrupt 0000:02:00.0[A] -> GSI 19 (level, high) -> IRQ 217
number of MP IRQ sources: 15.
number of IO-APIC #2 registers: 24.
testing the IO APIC.......................
IO APIC #2......
.... register #00: 02000000
....... : physical APIC id: 02
....... : Delivery Type: 0
....... : LTS : 0
.... register #01: 00170011
....... : max redirection entries: 0017
....... : PRQ implemented: 0
....... : IO APIC version: 0011
.... register #02: 00000000
....... : arbitration: 00
.... IRQ redirection table:
NR Log Phy Mask Trig IRR Pol Stat Dest Deli Vect:
00 000 00 1 0 0 0 0 0 0 00
01 001 01 0 0 0 0 0 1 1 39
02 000 00 1 0 0 0 0 0 0 00
03 001 01 0 0 0 0 0 1 1 41
04 001 01 0 0 0 0 0 1 1 49
05 001 01 0 0 0 0 0 1 1 51
06 001 01 0 0 0 0 0 1 1 59
07 001 01 1 0 0 0 0 1 1 61
08 001 01 0 0 0 0 0 1 1 69
09 001 01 0 1 0 0 0 1 1 71
0a 001 01 0 0 0 0 0 1 1 79
0b 001 01 0 0 0 0 0 1 1 81
0c 001 01 0 0 0 0 0 1 1 89
0d 001 01 0 0 0 0 0 1 1 91
0e 001 01 0 0 0 0 0 1 1 99
0f 001 01 0 0 0 0 0 1 1 A1
10 001 01 1 1 0 0 0 1 1 C9
11 000 00 1 0 0 0 0 0 0 00
12 001 01 1 1 0 0 0 1 1 D1
13 001 01 1 1 0 0 0 1 1 D9
14 001 01 1 1 0 0 0 1 1 C1
15 001 01 1 1 0 0 0 1 1 B9
16 001 01 1 1 0 0 0 1 1 B1
17 001 01 1 1 0 0 0 1 1 A9
Using vector-based indexing
IRQ to pin mappings:
IRQ0 -> 0:2
IRQ1 -> 0:1
IRQ3 -> 0:3
IRQ4 -> 0:4
IRQ5 -> 0:5
IRQ6 -> 0:6
IRQ7 -> 0:7
IRQ8 -> 0:8
IRQ9 -> 0:9
IRQ10 -> 0:10
IRQ11 -> 0:11
IRQ12 -> 0:12
IRQ13 -> 0:13
IRQ14 -> 0:14
IRQ15 -> 0:15
IRQ201 -> 0:16
IRQ209 -> 0:18
IRQ217 -> 0:19
IRQ193 -> 0:20
IRQ185 -> 0:21
IRQ177 -> 0:22
IRQ169 -> 0:23
.................................... done.
highmem bounce pool size: 64 pages
VFS: Disk quotas dquot_6.5.1
Dquot-cache hash table entries: 1024 (order 0, 4096 bytes)
devfs: 2004-01-31 Richard Gooch (rgooch@atnf.csiro.au)
devfs: boot_options: 0x0
Initializing Cryptographic API
isapnp: Scanning for PnP cards...
isapnp: No Plug & Play device found
Serial: 8250/16550 driver $Revision: 1.90 $ 48 ports, IRQ sharing enabled
ttyS0 at I/O 0x3f8 (irq = 4) is a 16550A
ttyS1 at I/O 0x2f8 (irq = 3) is a 16550A
RAMDISK driver initialized: 16 RAM disks of 8192K size 1024 blocksize
serio: i8042 AUX port at 0x60,0x64 irq 12
serio: i8042 KBD port at 0x60,0x64 irq 1
input: AT Translated Set 2 keyboard on isa0060/serio0
NET: Registered protocol family 2
IP: routing cache hash table of 8192 buckets, 64Kbytes
TCP: Hash tables configured (established 262144 bind 65536)
NET: Registered protocol family 8
NET: Registered protocol family 20
ACPI: (supports S0 S1 S4 S5)
RAMDISK: cramfs filesystem found at block 0
RAMDISK: Loading 4592 blocks [1 disk] into ram disk... done.
VFS: Mounted root (cramfs filesystem) readonly.
Freeing unused kernel memory: 148k freed
vesafb: probe of vesafb0 failed with error -6
NET: Registered protocol family 1
SCSI subsystem initialized
libata version 1.02 loaded.
sata_sil version 0.54
ACPI: PCI interrupt 0000:01:0d.0[A] -> GSI 18 (level, high) -> IRQ 209
ata1: SATA max UDMA/100 cmd 0xF881E080 ctl 0xF881E08A bmdma 0xF881E000 irq
209
ata2: SATA max UDMA/100 cmd 0xF881E0C0 ctl 0xF881E0CA bmdma 0xF881E008 irq
209
ata1: dev 0 cfg 49:2f00 82:74eb 83:7fea 84:4023 85:74e8 86:3c02 87:4023
88:203f
ata1: dev 0 ATA, max UDMA/100, 160836480 sectors: lba48
ata1: dev 0 configured for UDMA/100
scsi0 : sata_sil
ata2: dev 0 cfg 49:2f00 82:74eb 83:7fea 84:4023 85:74e8 86:3c02 87:4023
88:203f
ata2: dev 0 ATA, max UDMA/100, 160836480 sectors: lba48
ata2: dev 0 configured for UDMA/100
scsi1 : sata_sil
Using anticipatory io scheduler
Vendor: ATA Model: HDS722580VLSA80 Rev: V32O
Type: Direct-Access ANSI SCSI revision: 05
Vendor: ATA Model: HDS722580VLSA80 Rev: V32O
Type: Direct-Access ANSI SCSI revision: 05
SCSI device sda: 160836480 512-byte hdwr sectors (82348 MB)
SCSI device sda: drive cache: write back
/dev/scsi/host0/bus0/target0/lun0: p1 p2 < p5 p6 p7 p8 >
Attached scsi disk sda at scsi0, channel 0, id 0, lun 0
SCSI device sdb: 160836480 512-byte hdwr sectors (82348 MB)
SCSI device sdb: drive cache: write back
/dev/scsi/host1/bus0/target0/lun0: p1 p2 < p5 p6 p7 p8 >
Attached scsi disk sdb at scsi1, channel 0, id 0, lun 0
kjournald starting. Commit interval 5 seconds
EXT3-fs: mounted filesystem with ordered data mode.
Adding 2000048k swap on /dev/sda7. Priority:-1 extents:1
EXT3 FS on sda5, internal journal
Real Time Clock Driver v1.12
Uniform Multi-Platform E-IDE driver Revision: 7.00alpha2
ide: Assuming 33MHz system bus speed for PIO modes; override with idebus=xx
hda: RICOH CD-R/RW MP7200A, ATAPI CD/DVD-ROM drive
ide0 at 0x1f0-0x1f7,0x3f6 on irq 14
hda: ATAPI 40X CD-ROM CD-R/RW drive, 2048kB Cache
Uniform CD-ROM driver Revision: 3.20
Capability LSM initialized
kjournald starting. Commit interval 5 seconds
EXT3 FS on sda6, internal journal
EXT3-fs: mounted filesystem with ordered data mode.
r8169 Gigabit Ethernet driver 1.2 loaded
ACPI: PCI interrupt 0000:01:0b.0[A] -> GSI 16 (level, high) -> IRQ 201
eth0: Identified chip type is 'RTL8169s/8110s'.
eth0: RTL8169 at 0xf883b000, 00:0f:ea:32:69:31, IRQ 201
eth0: Auto-negotiation Enabled.
eth0: 100Mbps Full-duplex operation.
Intel 810 + AC97 Audio, version 1.01, 14:00:59 Aug 28 2004
ACPI: PCI interrupt 0000:00:06.0[A] -> GSI 22 (level, high) -> IRQ 177
PCI: Setting latency timer of device 0000:00:06.0 to 64
i810: NVIDIA nForce Audio found at IO 0xd800 and 0xd400, MEM 0x0000 and
0x0000, IRQ 177
i810_audio: Audio Controller supports 6 channels.
i810_audio: Defaulting to base 2 channel mode.
i810_audio: Resetting connection 0
ac97_codec: AC97 codec, id: ALG96 (Unknown)
i810_audio: only 48Khz playback available.
i810_audio: AC'97 codec 0 Unable to map surround DAC's (or DAC's not
present), total channels = 2
usbcore: registered new driver usbfs
usbcore: registered new driver hub
ACPI: PCI interrupt 0000:00:02.2[C] -> GSI 20 (level, high) -> IRQ 193
ehci_hcd 0000:00:02.2: nVidia Corporation nForce2 USB Controller
PCI: Setting latency timer of device 0000:00:02.2 to 64
ehci_hcd 0000:00:02.2: irq 193, pci mem f883d000
ehci_hcd 0000:00:02.2: new USB bus registered, assigned bus number 1
PCI: cache line size of 64 is not supported by device 0000:00:02.2
ehci_hcd 0000:00:02.2: USB 2.0 enabled, EHCI 1.00, driver 2004-May-10
hub 1-0:1.0: USB hub found
hub 1-0:1.0: 6 ports detected
input: PC Speaker
inserting floppy driver for 2.6.8-1-k7
Floppy drive(s): fd0 is 1.44M
FDC 0 is a post-1991 82077
parport: PnPBIOS parport detected.
parport0: PC-style at 0x378 (0x778), irq 7, dma 3
[PCSPP,TRISTATE,COMPAT,ECP,DMA]
Linux agpgart interface v0.100 (c) Dave Jones
agpgart: Detected NVIDIA nForce2 chipset
agpgart: Maximum main memory to use for agp memory: 941M
agpgart: AGP aperture is 64M @ 0xd8000000
ohci_hcd: 2004 Feb 02 USB 1.1 'Open' Host Controller (OHCI) Driver (PCI)
ohci_hcd: block sizes: ed 64 td 64
ACPI: PCI interrupt 0000:00:02.0[A] -> GSI 22 (level, high) -> IRQ 177
ohci_hcd 0000:00:02.0: nVidia Corporation nForce2 USB Controller
PCI: Setting latency timer of device 0000:00:02.0 to 64
ohci_hcd 0000:00:02.0: irq 177, pci mem f885c000
ohci_hcd 0000:00:02.0: new USB bus registered, assigned bus number 2
hub 2-0:1.0: USB hub found
hub 2-0:1.0: 3 ports detected
ACPI: PCI interrupt 0000:00:02.1[B] -> GSI 21 (level, high) -> IRQ 185
ohci_hcd 0000:00:02.1: nVidia Corporation nForce2 USB Controller (#2)
PCI: Setting latency timer of device 0000:00:02.1 to 64
ohci_hcd 0000:00:02.1: irq 185, pci mem f8a01000
ohci_hcd 0000:00:02.1: new USB bus registered, assigned bus number 3
hub 3-0:1.0: USB hub found
hub 3-0:1.0: 3 ports detected
usb 3-1: new low speed USB device using address 2
usbcore: registered new driver hiddev
input: USB HID v1.10 Mouse [Logitech USB-PS/2 Optical Mouse] on
usb-0000:00:02.1-1
usbcore: registered new driver usbhid
drivers/usb/input/hid-core.c: v2.0:USB HID core driver
mice: PS/2 mouse device common for all mice
ts: Compaq touchscreen protocol output
cpci_hotplug: CompactPCI Hot Plug Core version: 0.2
pci_hotplug: PCI Hot Plug PCI Core version: 0.5
pciehp: PCI Express Hot Plug Controller Driver version: 0.4
shpchp: shpc_init : shpc_cap_offset == 0
shpchp: shpc_init : shpc_cap_offset == 0
shpchp: Standard Hot Plug PCI Controller Driver version: 0.4
NFORCE2: IDE controller at PCI slot 0000:00:09.0
NFORCE2: chipset revision 162
NFORCE2: not 100% native mode: will probe irqs later
NFORCE2: 0000:00:09.0 (rev a2) UDMA133 controller
NFORCE2: port 0x01f0 already claimed by ide0
ide1: BM-DMA at 0xf008-0xf00f, BIOS settings: hdc:DMA, hdd:DMA
NET: Registered protocol family 10
Disabled Privacy Extensions on device c02f8de0(lo)
IPv6 over IPv4 tunneling driver
eth0: no IPv6 routers present
kjournald starting. Commit interval 5 seconds
EXT3 FS on sdb5, internal journal
EXT3-fs: mounted filesystem with ordered data mode.
md: md driver 0.90.0 MAX_MD_DEVS=256, MD_SB_DISKS=27
md: raid1 personality registered as nr 3
--
martin.henne at web.de
Reply to: