FibreChannel qla2300-Adapter mit hoeheren LUNs verwenden
Hallo,
ich versuche verzweifelt eine qla2300fl Karte unter Debian (woody) zum
Laufen zu bekommen. Das Modul habe ich von Qlogic herunter geladen und
nach Anleitung die Makefiles für den Kernel 2.4.20 angepasst und Kernel
neu übersetzt. Die zugehörige SAN Disk hat die LUN 10 was sich auch
nicht direkt ändern läßt, da am Controller nur noch die höheren LUNs
(> 8) verfügbar sind und ich keinen Zugriff auf den Controller habe.
Die Karte findet die Festplatten des Controllers, kann sie aber nicht
ansprechen. Ich vermute es liegt an der zu hohen LUN.
In lilo.conf ist append="max_scsi_luns=256 eingefügt. Interessant ist
dabei, daß das qla-Modul nach 8 LUNs abzubrechen scheint. Trotzdem
findet es die freigeschaltete Platte sde
das isp Modul von www.feral.com hat die gleichen Symptome, zählt aber
die vohandenen 16 LUNs durch (ist so im BIOS des Adapters eingestellt)
Hat jemand Erfahrungen oder Ideen?
Dank und Gruß juergen
PS
folgend noch der Output von modprobe qla2300 und modprobe isp_mod
modprobe qla2300 ergibt folgenden output
Jul 15 15:16:02 lisa kernel: qla2x00_set_info starts at address =
f88c5060
Jul 15 15:16:02 lisa kernel: qla2x00: Found VID=1077 DID=2300
SSVID=1077 SSDID=9
Jul 15 15:16:02 lisa kernel: scsi2: Found a QLA2300 @ bus 3, device
0x1, irq 24, iobase 0x3000
Jul 15 15:16:02 lisa kernel: scsi(2): Allocated 4096 SRB(s)
Jul 15 15:16:02 lisa kernel: scsi(2): Configure NVRAM parameters...
Jul 15 15:16:02 lisa kernel: scsi(2): 64 Bit PCI Addressing Enabled
Jul 15 15:16:02 lisa kernel: scsi(2): Verifying loaded RISC code...
Jul 15 15:16:02 lisa kernel: scsi(2): Verifying chip...
Jul 15 15:16:02 lisa kernel: scsi(2): Waiting for LIP to complete...
Jul 15 15:16:03 lisa kernel: scsi(2): LOOP UP detected
Jul 15 15:16:03 lisa kernel: scsi2: Topology - (F_Port), Host Loop
address 0xffff
Jul 15 15:16:05 lisa kernel: scsi2: Topology - (F_Port), Host Loop
address 0xffff
Jul 15 15:16:06 lisa kernel: scsi2 : QLogic QLA2300 PCI to Fibre Channel
Host Adapter: bus 3 device 1 irq 24
Jul 15 15:16:06 lisa kernel: Firmware version: 3.01.13, Driver
version 6.1b5
Jul 15 15:16:06 lisa kernel: Vendor: IBM Model: ProFibre PSEUDO
Rev: 5900
Jul 15 15:16:06 lisa kernel: Type: Direct-Access
ANSI SCSI revision: 02
Jul 15 15:16:06 lisa kernel: Vendor: IBM Model: ProFibre PSEUDO
Rev: 5900
Jul 15 15:16:06 lisa kernel: Type: Direct-Access
ANSI SCSI revision: 02
Jul 15 15:16:06 lisa kernel: Vendor: IBM Model: ProFibre PSEUDO
Rev: 5900
Jul 15 15:16:06 lisa kernel: Type: Direct-Access
ANSI SCSI revision: 02
Jul 15 15:16:06 lisa kernel: Vendor: IBM Model: ProFibre PSEUDO
Rev: 5900
Jul 15 15:16:06 lisa kernel: Type: Direct-Access
ANSI SCSI revision: 02
Jul 15 15:16:06 lisa kernel: Vendor: IBM Model: ProFibre PSEUDO
Rev: 5900
Jul 15 15:16:06 lisa kernel: Type: Direct-Access
ANSI SCSI revision: 02
Jul 15 15:16:06 lisa kernel: Vendor: IBM Model: ProFibre PSEUDO
Rev: 5900
Jul 15 15:16:06 lisa kernel: Type: Direct-Access
ANSI SCSI revision: 02
Jul 15 15:16:06 lisa kernel: Vendor: IBM Model: ProFibre PSEUDO
Rev: 5900
Jul 15 15:16:06 lisa kernel: Type: Direct-Access
ANSI SCSI revision: 02
Jul 15 15:16:06 lisa kernel: Vendor: IBM Model: ProFibre PSEUDO
Rev: 5900
Jul 15 15:16:06 lisa kernel: Type: Direct-Access
ANSI SCSI revision: 02
Jul 15 15:16:06 lisa kernel: Vendor: IBM Model: ProFibre PSEUDO
Rev: 5900
Jul 15 15:16:06 lisa kernel: Type: Direct-Access
ANSI SCSI revision: 02
Jul 15 15:16:06 lisa kernel: scsi(2:0:0:0): Enabled tagged queuing,
queue depth 16.
Jul 15 15:16:06 lisa kernel: scsi(2:0:0:1): Enabled tagged queuing,
queue depth 16.
Jul 15 15:16:06 lisa kernel: scsi(2:0:0:2): Enabled tagged queuing,
queue depth 16.
Jul 15 15:16:06 lisa kernel: scsi(2:0:0:3): Enabled tagged queuing,
queue depth 16.
Jul 15 15:16:06 lisa kernel: scsi(2:0:0:4): Enabled tagged queuing,
queue depth 16.
Jul 15 15:16:06 lisa kernel: scsi(2:0:0:5): Enabled tagged queuing,
queue depth 16.
Jul 15 15:16:06 lisa kernel: scsi(2:0:0:6): Enabled tagged queuing,
queue depth 16.
Jul 15 15:16:06 lisa kernel: scsi(2:0:0:7): Enabled tagged queuing,
queue depth 16.
Jul 15 15:16:06 lisa kernel: scsi(2:0:1:0): Enabled tagged queuing,
queue depth 16.
Jul 15 15:16:06 lisa kernel: Attached scsi disk sde at scsi2, channel 0,
id 0, lun 0
Jul 15 15:16:06 lisa kernel: Attached scsi disk sdf at scsi2, channel 0,
id 0, lun 1
Jul 15 15:16:06 lisa kernel: Attached scsi disk sdg at scsi2, channel 0,
id 0, lun 2
Jul 15 15:16:06 lisa kernel: Attached scsi disk sdh at scsi2, channel 0,
id 0, lun 3
Jul 15 15:16:06 lisa kernel: Attached scsi disk sdi at scsi2, channel 0,
id 0, lun 4
Jul 15 15:16:06 lisa kernel: Attached scsi disk sdj at scsi2, channel 0,
id 0, lun 5
Jul 15 15:16:06 lisa kernel: Attached scsi disk sdk at scsi2, channel 0,
id 0, lun 6
Jul 15 15:16:06 lisa kernel: Attached scsi disk sdl at scsi2, channel 0,
id 0, lun 7
Jul 15 15:16:06 lisa kernel: Attached scsi disk sdm at scsi2, channel 0,
id 1, lun 0
Jul 15 15:16:06 lisa kernel: sde : READ CAPACITY failed.
Jul 15 15:16:06 lisa kernel: sde : status = 1, message = 00, host = 0,
driver = 08
Jul 15 15:16:06 lisa kernel: Current sd00:00: sns = 70 5
Jul 15 15:16:06 lisa kernel: ASC=25 ASCQ= 0
Jul 15 15:16:06 lisa kernel: Raw sense data:0x70 0x00 0x05 0x00 0x00
0x00 0x00 0x0a 0x00 0x00 0x00 0x00 0x25 0x00 0x00 0x00 0x00 0x00
Jul 15 15:16:06 lisa kernel: sde : block size assumed to be 512 bytes,
disk size 1GB.
Jul 15 15:16:06 lisa kernel: sde: I/O error: dev 08:40, sector 0
Jul 15 15:16:06 lisa kernel: I/O error: dev 08:40, sector 0
Jul 15 15:16:06 lisa kernel: unable to read partition table
Jul 15 15:16:06 lisa kernel: sdm : READ CAPACITY failed.
Jul 15 15:16:06 lisa kernel: sdm : status = 1, message = 00, host = 0,
driver = 08
Jul 15 15:16:06 lisa kernel: Current sd00:00: sns = 70 5
Jul 15 15:16:06 lisa kernel: ASC=25 ASCQ= 0
Jul 15 15:16:06 lisa kernel: Raw sense data:0x70 0x00 0x05 0x00 0x00
0x00 0x00 0x0a 0x00 0x00 0x00 0x00 0x25 0x00 0x00 0x00 0x00 0x00
Jul 15 15:16:06 lisa kernel: sdm : block size assumed to be 512 bytes,
disk size 1GB.
Jul 15 15:16:06 lisa kernel: sdm: I/O error: dev 08:c0, sector 0
Jul 15 15:16:06 lisa kernel: I/O error: dev 08:c0, sector 0
Jul 15 15:16:06 lisa kernel: unable to read partition table
output von modprobe isp_mod
Jul 15 16:11:59 lisa kernel: ISP SCSI and Fibre Channel Host Adapter
Driver
Jul 15 16:11:59 lisa kernel: Linux Platform Version 2.1
Jul 15 16:11:59 lisa kernel: Common Core Code Version 2.7
Jul 15 16:11:59 lisa kernel: Built on Jul 15 2003, 14:14:21
Jul 15 16:11:59 lisa kernel: isp0: Board Type 2300, Chip Revision 0x1,
loaded F/W Revision 3.1.20
Jul 15 16:11:59 lisa kernel: isp0: Installed in 64-Bit PCI slot
Jul 15 16:11:59 lisa kernel: isp0: Last F/W revision was 3.1.13
Jul 15 16:11:59 lisa kernel: isp0: NVRAM Port WWN 0x210000e08b0b52f9
Jul 15 16:11:59 lisa kernel: scsi2 : Driver for a Qlogic ISP 2300 Host
Adapter
Jul 15 16:11:59 lisa kernel: blk: queue f7a43a18, I/O limit 4294967295Mb
(mask 0xffffffffffffffff)
Jul 15 16:11:59 lisa kernel: isp0: Loop ID 255, AL_PA 0x0, Port ID
0xb0100, Loop State 0x2, Topology 'F Port'
Jul 15 16:12:00 lisa kernel: Vendor: IBM Model: ProFibre PSEUDO
Rev: 5900
Jul 15 16:12:00 lisa kernel: Type: Direct-Access
ANSI SCSI revision: 02
Jul 15 16:12:00 lisa kernel: blk: queue f7a43e18, I/O limit 4294967295Mb
(mask 0xffffffffffffffff)
Jul 15 16:12:00 lisa kernel: Vendor: IBM Model: ProFibre PSEUDO
Rev: 5900
Jul 15 16:12:00 lisa kernel: Type: Direct-Access
ANSI SCSI revision: 02
Jul 15 16:12:00 lisa kernel: blk: queue f7a43c18, I/O limit 4294967295Mb
(mask 0xffffffffffffffff)
Jul 15 16:12:00 lisa kernel: Vendor: IBM Model: ProFibre PSEUDO
Rev: 5900
Jul 15 16:12:00 lisa kernel: Type: Direct-Access
ANSI SCSI revision: 02
Jul 15 16:12:00 lisa kernel: blk: queue f75c8c18, I/O limit 4294967295Mb
(mask 0xffffffffffffffff)
Jul 15 16:12:00 lisa kernel: Vendor: IBM Model: ProFibre PSEUDO
Rev: 5900
Jul 15 16:12:00 lisa kernel: Type: Direct-Access
ANSI SCSI revision: 02
Jul 15 16:12:00 lisa kernel: blk: queue f75c8e18, I/O limit 4294967295Mb
(mask 0xffffffffffffffff)
Jul 15 16:12:00 lisa kernel: Vendor: IBM Model: ProFibre PSEUDO
Rev: 5900
Jul 15 16:12:00 lisa kernel: Type: Direct-Access
ANSI SCSI revision: 02
Jul 15 16:12:00 lisa kernel: blk: queue f760bc18, I/O limit 4294967295Mb
(mask 0xffffffffffffffff)
Jul 15 16:12:00 lisa kernel: Vendor: IBM Model: ProFibre PSEUDO
Rev: 5900
Jul 15 16:12:00 lisa kernel: Type: Direct-Access
ANSI SCSI revision: 02
Jul 15 16:12:00 lisa kernel: blk: queue f760ba18, I/O limit 4294967295Mb
(mask 0xffffffffffffffff)
Jul 15 16:12:00 lisa kernel: Vendor: IBM Model: ProFibre PSEUDO
Rev: 5900
Jul 15 16:12:00 lisa kernel: Type: Direct-Access
ANSI SCSI revision: 02
Jul 15 16:12:00 lisa kernel: blk: queue f760b818, I/O limit 4294967295Mb
(mask 0xffffffffffffffff)
Jul 15 16:12:00 lisa kernel: Vendor: IBM Model: ProFibre PSEUDO
Rev: 5900
Jul 15 16:12:00 lisa kernel: Type: Direct-Access
ANSI SCSI revision: 02
Jul 15 16:12:00 lisa kernel: blk: queue f760b618, I/O limit 4294967295Mb
(mask 0xffffffffffffffff)
Jul 15 16:12:00 lisa kernel: Vendor: IBM Model: ProFibre PSEUDO
Rev: 5900
Jul 15 16:12:00 lisa kernel: Type: Direct-Access
ANSI SCSI revision: 02
Jul 15 16:12:00 lisa kernel: blk: queue f760b418, I/O limit 4294967295Mb
(mask 0xffffffffffffffff)
Jul 15 16:12:00 lisa kernel: Vendor: IBM Model: ProFibre PSEUDO
Rev: 5900
Jul 15 16:12:00 lisa kernel: Type: Direct-Access
ANSI SCSI revision: 02
Jul 15 16:12:00 lisa kernel: blk: queue f760b218, I/O limit 4294967295Mb
(mask 0xffffffffffffffff)
Jul 15 16:12:00 lisa kernel: Vendor: IBM Model: ProFibre PSEUDO
Rev: 5900
Jul 15 16:12:00 lisa kernel: Type: Direct-Access
ANSI SCSI revision: 02
Jul 15 16:12:00 lisa kernel: blk: queue f760b018, I/O limit 4294967295Mb
(mask 0xffffffffffffffff)
Jul 15 16:12:00 lisa kernel: Vendor: IBM Model: ProFibre PSEUDO
Rev: 5900
Jul 15 16:12:00 lisa kernel: Type: Direct-Access
ANSI SCSI revision: 02
Jul 15 16:12:00 lisa kernel: blk: queue f760be18, I/O limit 4294967295Mb
(mask 0xffffffffffffffff)
Jul 15 16:12:00 lisa kernel: Vendor: IBM Model: ProFibre PSEUDO
Rev: 5900
Jul 15 16:12:00 lisa kernel: Type: Direct-Access
ANSI SCSI revision: 02
Jul 15 16:12:00 lisa kernel: blk: queue f75b7a18, I/O limit 4294967295Mb
(mask 0xffffffffffffffff)
Jul 15 16:12:00 lisa kernel: Vendor: IBM Model: ProFibre PSEUDO
Rev: 5900
Jul 15 16:12:00 lisa kernel: Type: Direct-Access
ANSI SCSI revision: 02
Jul 15 16:12:00 lisa kernel: blk: queue f75b7c18, I/O limit 4294967295Mb
(mask 0xffffffffffffffff)
Jul 15 16:12:00 lisa kernel: Vendor: IBM Model: ProFibre PSEUDO
Rev: 5900
Jul 15 16:12:00 lisa kernel: Type: Direct-Access
ANSI SCSI revision: 02
Jul 15 16:12:00 lisa kernel: blk: queue f75b7e18, I/O limit 4294967295Mb
(mask 0xffffffffffffffff)
Jul 15 16:12:00 lisa kernel: Vendor: IBM Model: ProFibre PSEUDO
Rev: 5900
Jul 15 16:12:00 lisa kernel: Type: Direct-Access
ANSI SCSI revision: 02
Jul 15 16:12:00 lisa kernel: blk: queue f75b7018, I/O limit 4294967295Mb
(mask 0xffffffffffffffff)
Jul 15 16:12:00 lisa kernel: Attached scsi disk sde at scsi2, channel 0,
id 0, lun 0
Jul 15 16:12:00 lisa kernel: Attached scsi disk sdf at scsi2, channel 0,
id 0, lun 1
Jul 15 16:12:00 lisa kernel: Attached scsi disk sdg at scsi2, channel 0,
id 0, lun 2
Jul 15 16:12:00 lisa kernel: Attached scsi disk sdh at scsi2, channel 0,
id 0, lun 3
Jul 15 16:12:00 lisa kernel: Attached scsi disk sdi at scsi2, channel 0,
id 0, lun 4
Jul 15 16:12:00 lisa kernel: Attached scsi disk sdj at scsi2, channel 0,
id 0, lun 5
Jul 15 16:12:00 lisa kernel: Attached scsi disk sdk at scsi2, channel 0,
id 0, lun 6
Jul 15 16:12:00 lisa kernel: Attached scsi disk sdl at scsi2, channel 0,
id 0, lun 7
Jul 15 16:12:00 lisa kernel: Attached scsi disk sdm at scsi2, channel 0,
id 1, lun 0
Jul 15 16:12:00 lisa kernel: Attached scsi disk sdn at scsi2, channel 0,
id 1, lun 1
Jul 15 16:12:00 lisa kernel: Attached scsi disk sdo at scsi2, channel 0,
id 1, lun 2
Jul 15 16:12:00 lisa kernel: Attached scsi disk sdp at scsi2, channel 0,
id 1, lun 3
Jul 15 16:12:00 lisa kernel: Attached scsi disk sdq at scsi2, channel 0,
id 1, lun 4
Jul 15 16:12:00 lisa kernel: Attached scsi disk sdr at scsi2, channel 0,
id 1, lun 5
Jul 15 16:12:00 lisa kernel: Attached scsi disk sds at scsi2, channel 0,
id 1, lun 6
Jul 15 16:12:00 lisa kernel: Attached scsi disk sdt at scsi2, channel 0,
id 1, lun 7
Jul 15 16:12:00 lisa kernel: sde : READ CAPACITY failed.
Jul 15 16:12:00 lisa kernel: sde : status = 1, message = 00, host = 0,
driver = 08
Jul 15 16:12:00 lisa kernel: Current sd00:00: sns = 70 5
Jul 15 16:12:00 lisa kernel: ASC=25 ASCQ= 0
Jul 15 16:12:00 lisa kernel: Raw sense data:0x70 0x00 0x05 0x00 0x00
0x00 0x00 0x0a 0x00 0x00 0x00 0x00 0x25 0x00 0x00 0x00 0x00 0x00
Jul 15 16:12:00 lisa kernel: sde : block size assumed to be 512 bytes,
disk size 1GB.
Jul 15 16:12:00 lisa kernel: sde: I/O error: dev 08:40, sector 0
Jul 15 16:12:00 lisa kernel: I/O error: dev 08:40, sector 0
Jul 15 16:12:00 lisa kernel: unable to read partition table
Jul 15 16:12:00 lisa kernel: sdm : READ CAPACITY failed.
Jul 15 16:12:00 lisa kernel: sdm : status = 1, message = 00, host = 0,
driver = 08
Jul 15 16:12:00 lisa kernel: Current sd00:00: sns = 70 5
Jul 15 16:12:00 lisa kernel: ASC=25 ASCQ= 0
Jul 15 16:12:00 lisa kernel: Raw sense data:0x70 0x00 0x05 0x00 0x00
0x00 0x00 0x0a 0x00 0x00 0x00 0x00 0x25 0x00 0x00 0x00 0x00 0x00
Jul 15 16:12:00 lisa kernel: sdm : block size assumed to be 512 bytes,
disk size 1GB.
Jul 15 16:12:00 lisa kernel: sdm: I/O error: dev 08:c0, sector 0
Jul 15 16:12:00 lisa kernel: I/O error: dev 08:c0, sector 0
Jul 15 16:12:00 lisa kernel: unable to read partition table
Jul 15 16:12:01 lisa kernel: isp0: Loop ID 255, AL_PA 0x0, Port ID
0xb0100, Loop State 0x2, Topology 'F Port'
Jul 15 16:12:01 lisa kernel: isp0: Retained login of Target 0 (Loop ID
0x0) Port 0x60000
Jul 15 16:12:01 lisa kernel: isp0: Retained login of Target 1 (Loop ID
0x1) Port 0x60200
Reply to: