Re: Probleme carte Wifi chipset zydas
Bonjour à tous,
Voila ma config reseau:
n'ayant pas de carte filaire sur mon portable (IBM Thinkpad x21 (carte reseau foutu)) j'ai donc acheté une carte pcmcia D-link (rj45) qui est déclaré comme eth0 ensuite ayant un reseau wifi chez moi j'ai acheté une carte wifi Netgear pcmcia WG511 compatible uniquement avec ndiswrapper, cette carte est déclaré en wlan0, et enfin je souhaiterai pouvoir utiliser ma carte wifi a base Zydas.
Suivant ton conseil j'ai fais un "rmmod ndiswrapper" et un "modprobe -v zd1211 && modprobe -v zd1211b && depmod -a" pour relancer tout cela.
Sa m'a donné:
9:09 root@gabz-IBM-deb /home/gabz# lsmod
Module Size Used by
zd1211b 280704 0
zd1211 279776 0
ehci_hcd 25192 0
nfsd 82344 13
exportfs 4960 1 nfsd
lockd 53672 2 nfsd
sunrpc 131620 8 nfsd,lockd
agpgart 29244 0
usbhid 25764 0
ide_cd 35296 0
cdrom 32016 1 ide_cd
ide_cs 9440 1
uhci_hcd 26640 0
pcmcia 34324 1 ide_cs
shpchp 37312 0
usbcore 109152 6 zd1211b,zd1211,ehci_hcd,usbhid,uhci_hcd
pci_hotplug 24308 1 shpchp
(auparavant j'avais débrancher les cartes reseau et je n'ai réinséré que la carte a base Zydas)
Cela me donne:
9:09 root@gabz-IBM-deb /home/gabz# dmesg
Linux version 2.6.16-geekonors (root@gabz-IBM-deb) (gcc version 4.0.3 (Debian 4. 0.3-1)) #7 Sun Apr 9 14:22:34 CEST 2006
BIOS-provided physical RAM map:
BIOS-e820: 0000000000000000 - 000000000009f800 (usable)
BIOS-e820: 000000000009f800 - 00000000000a0000 (reserved)
BIOS-e820: 00000000000dd400 - 0000000000100000 (reserved)
BIOS-e820: 0000000000100000 - 000000000bff0000 (usable)
BIOS-e820: 000000000bff0000 - 000000000bffec00 (ACPI data)
BIOS-e820: 000000000bffec00 - 000000000c000000 (ACPI NVS)
BIOS-e820: 00000000fff80000 - 0000000100000000 (reserved)
191MB LOWMEM available.
On node 0 totalpages: 49136
DMA zone: 4096 pages, LIFO batch:0
DMA32 zone: 0 pages, LIFO batch:0
Normal zone: 45040 pages, LIFO batch:7
HighMem zone: 0 pages, LIFO batch:0
DMI 2.3 present.
Allocating PCI resources starting at 10000000 (gap: 0c000000:f3f80000)
Built 1 zonelists
Kernel command line: root=/dev/hda1 ro
Local APIC disabled by BIOS -- you can enable it with "lapic"
mapped APIC to ffffd000 (01181000)
Enabling fast FPU save and restore... done.
Enabling unmasked SIMD FPU exception support... done.
Initializing CPU#0
PID hash table entries: 1024 (order: 10, 16384 bytes)
Detected 497.893 MHz processor.
Using tsc for high-res timesource
Console: colour VGA+ 80x25
Dentry cache hash table entries: 32768 (order: 5, 131072 bytes)
Inode-cache hash table entries: 16384 (order: 4, 65536 bytes)
Memory: 192020k/196544k available (1440k kernel code, 4044k reserved, 579k data, 116k init, 0k highmem)
Checking if this processor honours the WP bit even in supervisor mode... Ok.
Calibrating delay using timer specific routine.. 951.50 BogoMIPS (lpj=1903002)
Mount-cache hash table entries: 512
CPU: After generic identify, caps: 0383f9ff 00000000 00000000 00000000 00000000 00000000 00000000
CPU: After vendor identify, caps: 0383f9ff 00000000 00000000 00000000 00000000 0 0000000 00000000
CPU: L1 I cache: 16K, L1 D cache: 16K
CPU: L2 cache: 256K
CPU: After all inits, caps: 0383f9ff 00000000 00000000 00000040 00000000 0000000 0 00000000
Intel machine check architecture supported.
Intel machine check reporting enabled on CPU#0.
CPU: Intel Pentium III (Coppermine) stepping 06
Checking 'hlt' instruction... OK.
NET: Registered protocol family 16
PCI: PCI BIOS revision 2.10 entry at 0xfd94f, last bus=7
PCI: Using configuration type 1
SCSI subsystem initialized
PCI: Probing PCI hardware
PCI: Probing PCI hardware (bus 00)
PCI quirk: region 1000-103f claimed by PIIX4 ACPI
PCI quirk: region 1040-104f claimed by PIIX4 SMB
PIIX4 devres I PIO at 03f0-03f7
PIIX4 devres J PIO at 002e-002f
Boot video device is 0000:01:00.0
PCI: Discovered primary peer bus 08 [IRQ]
PCI: Using IRQ router PIIX/ICH [8086/7110] at 0000:00:07.0
PCI: Bridge: 0000:00:01.0
IO window: 3000-3fff
MEM window: f4100000-f5ffffff
PREFETCH window: 18000000-180fffff
PCI: Bus 2, cardbus bridge: 0000:00:08.0
IO window: 00001400-000014ff
IO window: 00001c00-00001cff
PREFETCH window: 10000000-11ffffff
MEM window: 12000000-13ffffff
PCI: Bus 6, cardbus bridge: 0000:00:08.1
IO window: 00002400-000024ff
IO window: 00002800-000028ff
PREFETCH window: 14000000-15ffffff
MEM window: 16000000-17ffffff
PCI: Found IRQ 11 for device 0000:00:08.0
PCI: Sharing IRQ 11 with 0000:00:0b.0
PCI: Sharing IRQ 11 with 0000:01:00.0
PCI: Found IRQ 11 for device 0000:00:08.1
Machine check exception polling timer started.
IBM machine detected. Enabling interrupts during APM calls.
apm: BIOS version 1.2 Flags 0x03 (Driver version 1.16ac)
Initializing Cryptographic API
io scheduler noop registered
io scheduler anticipatory registered (default)
io scheduler deadline registered
io scheduler cfq registered
Limiting direct PCI/PCI transfers.
serio: i8042 AUX port at 0x60,0x64 irq 12
serio: i8042 KBD port at 0x60,0x64 irq 1
ipw2100: Intel(R) PRO/Wireless 2100 Network Driver, 1.1.3
ipw2100: Copyright(c) 2003-2005 Intel Corporation
ipw2200: Intel(R) PRO/Wireless 2200/2915 Network Driver, git-1.0.8
ipw2200: Copyright(c) 2003-2005 Intel Corporation
STRIP: Version 1.3A-STUART.CHESHIRE (unlimited channels)
orinoco 0.15rc3 (David Gibson <hermes@gibson.dropbear.id.au>, Pavel Roskin <pros ki@gnu.org>, et al)
orinoco_plx 0.15rc3 (Pavel Roskin <proski@gnu.org>, David Gibson <hermes@gibson. dropbear.id.au>, Daniel Barlow <dan@telent.net>)
orinoco_pci 0.15rc3 (Pavel Roskin <proski@gnu.org>, David Gibson <hermes@gibson. dropbear.id.au> & Jean Tourrilhes <jt@hpl.hp.com>)
orinoco_tmd 0.15rc3 (Joerg Dorchain <joerg@dorchain.net>)
orinoco_nortel 0.15rc3 (Tobias Hoffmann & Christoph Jungegger <disdos@traum404.d e>)
airo: Probing for PCI adapters
airo: Finished probing for PCI adapters
Loaded prism54 driver, version 1.2
Uniform Multi-Platform E-IDE driver Revision: 7.00alpha2
ide: Assuming 33MHz system bus speed for PIO modes; override with idebus=xx
Probing IDE interface ide0...
hda: HITACHI_DK23BA-10B, ATA DISK drive
Probing IDE interface ide1...
ide0 at 0x1f0-0x1f7,0x3f6 on irq 14
hda: max request size: 128KiB
hda: 19640880 sectors (10056 MB) w/512KiB Cache, CHS=20784/15/63
hda: cache flushes not supported
hda: hda1 hda2 < hda5 >
PCI: Found IRQ 11 for device 0000:00:08.0
PCI: Sharing IRQ 11 with 0000:00:0b.0
PCI: Sharing IRQ 11 with 0000:01:00.0
Yenta: CardBus bridge found at 0000:00:08.0 [1014:0185]
Yenta: ISA IRQ mask 0x06b8, PCI irq 11
Socket status: 30000820
PCI: Found IRQ 11 for device 0000:00:08.1
Yenta: CardBus bridge found at 0000:00:08.1 [1014:0185]
Yenta: ISA IRQ mask 0x06b8, PCI irq 11
Socket status: 30000810
mice: PS/2 mouse device common for all mice
NET: Registered protocol family 2
input: AT Translated Set 2 keyboard as /class/input/input0
IP route cache hash table entries: 2048 (order: 1, 8192 bytes)
TCP established hash table entries: 8192 (order: 3, 32768 bytes)
TCP bind hash table entries: 8192 (order: 3, 32768 bytes)
TCP: Hash tables configured (established 8192 bind 8192)
TCP reno registered
TCP bic registered
NET: Registered protocol family 1
NET: Registered protocol family 17
ieee80211: 802.11 data/management/control stack, git-1.1.7
ieee80211: Copyright (C) 2004-2005 Intel Corporation <jketreno@linux.intel.com>
ieee80211_crypt: registered algorithm 'NULL'
ieee80211_crypt: registered algorithm 'WEP'
Using IPI Shortcut mode
EXT3-fs: INFO: recovery required on readonly filesystem.
EXT3-fs: write access will be enabled during recovery.
pccard: CardBus card inserted into slot 0
kjournald starting. Commit interval 5 seconds
EXT3-fs: recovery complete.
EXT3-fs: mounted filesystem with ordered data mode.
VFS: Mounted root (ext3 filesystem) readonly.
Freeing unused kernel memory: 116k freed
IBM TrackPoint firmware: 0x0e, buttons: 3/3
pccard: PCMCIA card inserted into slot 1
input: TPPS/2 IBM TrackPoint as /class/input/input1
pci_hotplug: PCI Hot Plug PCI Core version: 0.5
usbcore: registered new driver usbfs
usbcore: registered new driver hub
shpchp: Standard Hot Plug PCI Controller Driver version: 0.4
USB Universal Host Controller Interface driver v2.3
PCI: Found IRQ 11 for device 0000:00:07.2
uhci_hcd 0000:00:07.2: UHCI Host Controller
uhci_hcd 0000:00:07.2: new USB bus registered, assigned bus number 1
uhci_hcd 0000:00:07.2: irq 11, io base 0x00001820
usb usb1: configuration #1 chosen from 1 choice
hub 1-0:1.0: USB hub found
hub 1-0:1.0: 2 ports detected
usb 1-1: new full speed USB device using uhci_hcd and address 2
usb 1-1: configuration #1 chosen from 1 choice
cs: memory probe 0x0c0000-0x0fffff:<6>hub 1-1:1.0: USB hub found
hub 1-1:1.0: 2 ports detected
excluding 0xc0000-0xcffff 0xd8000-0xfffff
cs: memory probe 0x60000000-0x60ffffff: clean.
cs: memory probe 0xa0000000-0xa0ffffff: clean.
pcmcia: registering new device pcmcia1.0
usb 1-1.1: new full speed USB device using uhci_hcd and address 3
Probing IDE interface ide1...
hdc: SanDisk SDCFB-8, CFA DISK drive
ide1 at 0x100-0x107,0x10e on irq 11
hdc: max request size: 128KiB
hdc: 15680 sectors (8 MB) w/1KiB Cache, CHS=245/2/32
hdc: hdc1
ide-cs: hdc: Vcc = 3.3, Vpp = 0.0
Adding 433712k swap on /dev/hda5. Priority:-1 extents:1 across:433712k
EXT3 FS on hda1, internal journal
usb 1-1.1: device descriptor read/64, error -110
ndiswrapper version 1.13 loaded (preempt=no,smp=no)
ndiswrapper: driver wg511v2 () loaded
PCI: Enabling device 0000:02:00.0 (0000 -> 0002)
PCI: Setting latency timer of device 0000:02:00.0 to 64
ndiswrapper: using irq 11
wlan0: vendor: ''
wlan0: ndiswrapper ethernet device 00:14:6c:2d:2c:9d using driver wg511v2, 11AB: 1FAA:1385:4E00.5.conf
wlan0: encryption modes supported: WEP; TKIP with WPA
pcmcia: Detected deprecated PCMCIA ioctl usage.
pcmcia: This interface will soon be removed from the kernel; please expect break age unless you upgrade to new tools.
pcmcia: see http://www.kernel.org/pub/linux/utils/kernel/pcmcia/pcmcia.html for details.
cs: memory probe 0x0c0000-0x0fffff: excluding 0xc0000-0xc7fff 0xf0000-0xfffff
cs: memory probe 0x60000000-0x60ffffff: excluding 0x60000000-0x600fffff
cs: memory probe 0xa0000000-0xa0ffffff: clean.
usb 1-1.1: device descriptor read/64, error -110
usb 1-1.1: new full speed USB device using uhci_hcd and address 4
usb 1-1.1: device descriptor read/64, error -110
usb 1-1.1: device descriptor read/64, error -110
usb 1-1.1: new full speed USB device using uhci_hcd and address 5
usb 1-1.1: device not accepting address 5, error -110
usb 1-1.1: new full speed USB device using uhci_hcd and address 6
usb 1-1.1: device not accepting address 6, error -110
usb 1-1.2: new low speed USB device using uhci_hcd and address 7
usb 1-1.2: configuration #1 chosen from 1 choice
input: HID 062a:0001 as /class/input/input2
input: USB HID v1.10 Mouse [HID 062a:0001] on usb-0000:00:07.2-1.2
usbcore: registered new driver usbhid
drivers/usb/input/hid-core.c: v2.6:USB HID core driver
Linux agpgart interface v0.101 (c) Dave Jones
Installing knfsd (copyright (C) 1996 okir@monad.swb.de).
usb 1-1.1: new full speed USB device using uhci_hcd and address 8
usb 1-1.1: configuration #1 chosen from 1 choice
_____ ____ _ ____
|__ / _| _ \ / \ / ___|
/ / | | | | | |/ _ \ \___ \
/ /| |_| | |_| / ___ \ ___) |
/____\__, |____/_/ \_\____/
|___/
zd1211 - version 2.5.0.0
Release Ver = 4330
zd1211:bulk out: wMaxPacketSize = 40
zd1211:bulk in: wMaxPacketSize = 40
zd1211:interrupt in: wMaxPacketSize = 40
zd1211:interrupt in: int_interval = 1
zd1211:bulk out: wMaxPacketSize = 40
EEPORM Ver = 4330
zd1211:USB Download Boot code success
zd1211:MAC address = 00:0e:2e:50:78:fb
zd1211:AddrEntryTable = f7d4
zd1211:RF_Mode = 00000004
PA type: 0
AiroHa AL2230RF
zd1211:Pure B-Mode
zd1211:File opening did not success
zd1211:AllowedChannel = 000007ff
zd1211:LinkLEDn = 200
AllowedChannel = 000107ff
Region:48
zd1205: (exit) zd1205_config, /root/ZD1211LnxDrv_2_6_0_0/src/zd1205.c line 2493
zd1205: (exit) zd1205_init, /root/ZD1211LnxDrv_2_6_0_0/src/zd1205.c line 7977
usbcore: registered new driver zd1211
_____ ____ _ ____
|__ / _| _ \ / \ / ___|
/ / | | | | | |/ _ \ \___ \
/ /| |_| | |_| / ___ \ ___) |
/____\__, |____/_/ \_\____/
|___/
ZD1211B - version 2.5.0.0
usbcore: registered new driver zd1211b
ndiswrapper: device wlan0 removed
ndiswrapper version 1.13 loaded (preempt=no,smp=no)
ndiswrapper: driver wg511v2 () loaded
PCI: Setting latency timer of device 0000:02:00.0 to 64
ndiswrapper: using irq 11
wlan0: vendor: ''
wlan0: ndiswrapper ethernet device 00:14:6c:2d:2c:9d using driver wg511v2, 11AB: 1FAA:1385:4E00.5.conf
wlan0: encryption modes supported: WEP; TKIP with WPA
eth0 (WE) : Driver using old /proc/net/wireless support, please fix driver !
spurious 8259A interrupt: IRQ7.
ndiswrapper: device wlan0 removed
usbcore: deregistering driver zd1211
zd1211:USB ST Code = -108
usbcore: deregistering driver zd1211b
_____ ____ _ ____
|__ / _| _ \ / \ / ___|
/ / | | | | | |/ _ \ \___ \
/ /| |_| | |_| / ___ \ ___) |
/____\__, |____/_/ \_\____/
|___/
zd1211 - version 2.5.0.0
Release Ver = 4330
zd1211:bulk out: wMaxPacketSize = 40
zd1211:bulk in: wMaxPacketSize = 40
zd1211:interrupt in: wMaxPacketSize = 40
zd1211:interrupt in: int_interval = 1
zd1211:bulk out: wMaxPacketSize = 40
EEPORM Ver = 4330
zd1211:USB Download Boot code success
usb_set_configuration() failed
zd1211: probe of 1-1.1:1.0 failed with error -5
usbcore: registered new driver zd1211
_____ ____ _ ____
|__ / _| _ \ / \ / ___|
/ / | | | | | |/ _ \ \___ \
/ /| |_| | |_| / ___ \ ___) |
/____\__, |____/_/ \_\____/
|___/
ZD1211B - version 2.5.0.0
usbcore: registered new driver zd1211b
usb 1-1.1: USB disconnect, address 8
usbcore: deregistering driver zd1211b
usbcore: deregistering driver zd1211
usb 1-1.1: new full speed USB device using uhci_hcd and address 9
usb 1-1.1: configuration #1 chosen from 1 choice
_____ ____ _ ____
|__ / _| _ \ / \ / ___|
/ / | | | | | |/ _ \ \___ \
/ /| |_| | |_| / ___ \ ___) |
/____\__, |____/_/ \_\____/
|___/
zd1211 - version 2.5.0.0
Release Ver = 4330
zd1211:bulk out: wMaxPacketSize = 40
zd1211:bulk in: wMaxPacketSize = 40
zd1211:interrupt in: wMaxPacketSize = 40
zd1211:interrupt in: int_interval = 1
zd1211:bulk out: wMaxPacketSize = 40
EEPORM Ver = 4330
zd1211:USB Download Boot code success
zd1211:MAC address = 00:0e:2e:50:78:fb
zd1211:AddrEntryTable = f7d4
zd1211:RF_Mode = 00000004
PA type: 0
AiroHa AL2230RF
zd1211:Pure B-Mode
zd1211:File opening did not success
zd1211:AllowedChannel = 000007ff
zd1211:LinkLEDn = 200
AllowedChannel = 000107ff
Region:48
zd1205: (exit) zd1205_config, /root/ZD1211LnxDrv_2_6_0_0/src/zd1205.c line 2493
zd1205: (exit) zd1205_init, /root/ZD1211LnxDrv_2_6_0_0/src/zd1205.c line 7977
usbcore: registered new driver zd1211
_____ ____ _ ____
|__ / _| _ \ / \ / ___|
/ / | | | | | |/ _ \ \___ \
/ /| |_| | |_| / ___ \ ___) |
/____\__, |____/_/ \_\____/
|___/
ZD1211B - version 2.5.0.0
usbcore: registered new driver zd1211b
Voila donc il me semble que le modules est correctement inséré mais quand je fais un :
9:19 root@gabz-IBM-deb /home/gabz# airmon
usage: /usr/sbin/airmon <start|stop> <interface> [channel]
Interface Chipset Driver
Donc po de carte wifi!!?
Aidez moi Pliz
--
Pensez à lire la FAQ de la liste avant de poser une question :
http://wiki.debian.net/?DebianFrench
Pensez à rajouter le mot ``spam'' dans vos champs "From" et "Reply-To:"
To UNSUBSCRIBE, email to debian-user-french-REQUEST@lists.debian.org
with a subject of "unsubscribe". Trouble? Contact listmaster@lists.debian.org
Reply to: