orinoco et mode monitor
Hi,
Je suis un jeune administarteur reseau et je dois dire que je rencontre
quelques problemes avec l'install dans mon systeme d'une carte orinoco
gold.Et je dois bien vous avouer que j aurais grand besoin de l'aide
quelqu'un qui aurait fait cela.
J ai un toshiba laptop 2450 et un kernel 2.6.14
2.6.14 #1 SMP Fri Jan 20 11:34:25 CET 2006 i686 GNU/Linux
J utilise les drivers 0.15RC2 et si mes recherches ne sont pas
infondées, le patch mod emonitor est dedans.
This is the resul of dmesg | grep orinoco
orinoco 0.15rc2 (David Gibson <hermes@gibson.dropbear.id.au>, Pavel
Roskin <proski@gnu.org>, et al)
orinoco_cs 0.15rc2 (David Gibson <hermes@gibson.dropbear.id.au>, Pavel
Roskin <proski@gnu.org>, et al)
Je pensais que c etait un bon debut mais je me suis trompé.
This is the result of lsmod :
Module Size Used by
snd_pcm_oss 56864 0
snd_mixer_oss 22912 4 snd_pcm_oss
orinoco_cs 18056 1
pcmcia 44588 5 orinoco_cs
joydev 13760 0
parport_pc 45380 0
parport 41288 1 parport_pc
yenta_socket 31116 6
rsrc_nonstatic 17536 1 yenta_socket
pcmcia_core 48408 3 pcmcia,yenta_socket,rsrc_nonstatic
Voila le resultat de iwconfig :
eth1 IEEE 802.11-DS ESSID:"My_Network" Nickname:"Seth"
Mode:Managed Bit Rate:11 Mb/s
RTS thr:off
Encryption key:7365-6375-31 Security mode:open
Link Quality:0 Signal level:134 Noise level:134
Rx invalid nwid:0 invalid crypt:0 invalid misc:0
Un ifconfig eth1 m'a donné ca :
eth1 Lien encap:Ethernet HWaddr 00:02:2D:38:5B:F6
inet adr:192.168.1.12 Bcast:192.168.1.255
Masque:255.255.255.0
BROADCAST PROMISC MULTICAST MTU:1500 Metric:1
RX packets:0 errors:0 dropped:0 overruns:0 frame:0
TX packets:0 errors:0 dropped:0 overruns:0 carrier:0
collisions:0 lg file transmission:1000
RX bytes:0 (0.0 b) TX bytes:0 (0.0 b)
Interruption:3 Adresse de base:0xc100
Mais le resultat de cette commande : airmon start eth1 me donne ca
eth1 HermesI orinocoSIOCSIFFLAGS: Périphérique ou
ressource occupé
(monitor mode enabled)
Et lorsque je lance kismet, j obtiens plutot ca :
Server options: none
Client options: none
Starting server...
Waiting for server to start before starting UI...
Suid priv-dropping disabled. This may not be secure.
No specific sources given to be enabled, all will be enabled.
Enabling channel hopping.
Enabling channel splitting.
Source 0 (HermesI): Enabling monitor mode for orinoco source interface
eth1 channel 10...
FATAL: channel get ioctl failed 16:Device or resource busy
Et en conclusion le resultat de iwpriv me donne ca :
eth1 Available private ioctls :
force_reset (8BE0) : set 0 & get 0
card_reset (8BE1) : set 0 & get 0
set_port3 (8BE2) : set 1 int & get 0
get_port3 (8BE3) : set 0 & get 1 int
set_preamble (8BE4) : set 1 int & get 0
get_preamble (8BE5) : set 0 & get 1 int
set_ibssport (8BE6) : set 1 int & get 0
get_ibssport (8BE7) : set 0 & get 1 int
get_rid (8BE9) : set 0 & get 1024 byte
Quelqu un a deja rencontré se probleme ? Pourriez vous m aider a trouver
une solution. Lorsque j utilise Whax, tout se passe impeccable et la
carte est parfaitement reconnue et bien gérée. Que puis je faire ?
Please help me to solve it ! I prefer to use Debian !!
Thanks for you help !!!
best regards
PP
Reply to: