Tout d'abord bonjour et désolé par avance si je ne suis pas assez
précis (c'est mon premier post sur un forum linuxien et je suis
débutant).
Donc j'ai un problème lorsque j'essaie de monter ma clé USB :
*mount -t vfat /dev/sda1 /mnt/CleUSB
mount: /dev/sda1 n'est pas un périphérique valide de type bloc*
(tiens je viens de remarquer que j'ai le même message si je ne branche
pas la clé huhu^^)
La commande file /dev/sda1 me retourne :
*/dev/sda1: block special (8/1)
*
Je précise que la clé marchait correctement sous windows avant donc le
problème ne vient pas de là.
Je vous copie la partie concernée de dmsg au cas où :
*usbcore: registered new driver usbfs
usbcore: registered new driver hub
USB Universal Host Controller Interface driver v2.2
uhci_hcd 0000:00:10.0: VIA Technologies, Inc. VT82xxxxx UHCI USB 1.1
Controller
uhci_hcd 0000:00:10.0: irq 21, io base 0xd800
uhci_hcd 0000:00:10.0: new USB bus registered, assigned bus number 1
hub 1-0:1.0: USB hub found
hub 1-0:1.0: 2 ports detected
uhci_hcd 0000:00:10.1: VIA Technologies, Inc. VT82xxxxx UHCI USB 1.1
Controller (#2)
uhci_hcd 0000:00:10.1: irq 21, io base 0xdc00
uhci_hcd 0000:00:10.1: new USB bus registered, assigned bus number 2
hub 2-0:1.0: USB hub found
hub 2-0:1.0: 2 ports detected
uhci_hcd 0000:00:10.2: VIA Technologies, Inc. VT82xxxxx UHCI USB 1.1
Controller (#3)
uhci_hcd 0000:00:10.2: irq 21, io base 0xe000
uhci_hcd 0000:00:10.2: new USB bus registered, assigned bus number 3
hub 3-0:1.0: USB hub found
hub 3-0:1.0: 2 ports detected
usb 1-2: new full speed USB device using uhci_hcd and address 2
ehci_hcd 0000:00:10.3: VIA Technologies, Inc. USB 2.0
ehci_hcd 0000:00:10.3: irq 21, pci mem 0xdb011000
ehci_hcd 0000:00:10.3: new USB bus registered, assigned bus number 4
ehci_hcd 0000:00:10.3: USB 2.0 initialized, EHCI 1.00, driver 26 Oct 2004
hub 4-0:1.0: USB hub found
hub 4-0:1.0: 6 ports detected
usb 1-2: USB disconnect, address 2
via82xx: Assuming DXS channels with 48k fixed sample rate.
Please try dxs_support=1 or dxs_support=4 option
and report if it works on your machine.
PCI: Setting latency timer of device 0000:00:11.5 to 64
usb 4-4: new high speed USB device using ehci_hcd and address 3
hub 4-4:1.0: USB hub found
hub 4-4:1.0: 2 ports detected
usb 1-2: new full speed USB device using uhci_hcd and address 3
usb 4-4.1: new high speed USB device using ehci_hcd and address 5
SCSI subsystem initialized
Initializing USB Mass Storage driver...
usb 4-4.2: new high speed USB device using ehci_hcd and address 6
usb-storage: USB Mass Storage device detected
usb-storage: -- associate_dev
usb-storage: Vendor: 0x0caf, Product: 0x2517, Revision: 0x0001
usb-storage: Interface Subclass: 0x05, Protocol: 0x50
usb-storage: Vendor: TSE Inc., Product: USB Mass Storage Device
usb-storage: Transport: Bulk
usb-storage: Protocol: 8070i
usb-storage: usb_stor_control_msg: rq=fe rqtype=a1 value=0000 index=00
len=1
usb-storage: GetMaxLUN command result is 1, data is 0
scsi0 : SCSI emulation for USB Mass Storage devices
usbcore: registered new driver usb-storage
USB Mass Storage support registered.
usb-storage: *** thread sleeping.
usb-storage: device found at 5
usb-storage: waiting for device to settle before scanning
usb 3-1: new full speed USB device using uhci_hcd and address 2
usb-storage: USB Mass Storage device detected
usb-storage: -- associate_dev
usb-storage: Vendor: 0x1019, Product: 0x0c55, Revision: 0x0100
usb-storage: Interface Subclass: 0x06, Protocol: 0x50
usb-storage: Vendor: Generic , Product: USB Storage Device
usb-storage: Transport: Bulk
usb-storage: Protocol: Transparent SCSI
usb-storage: usb_stor_control_msg: rq=fe rqtype=a1 value=0000 index=00
len=1
usb-storage: GetMaxLUN command result is 1, data is 3
usb-storage: Sending UCR-61S2B initialization packet...
usb-storage: usb_stor_bulk_transfer_buf: xfer 31 bytes
usb-storage: Status code 0; transferred 31/31
usb-storage: -- transfer complete
usb-storage: Getting status packet...
usb-storage: usb_stor_bulk_transfer_buf: xfer 13 bytes
eth0: link up, 100Mbps, full-duplex, lpa 0x45E1
usb-storage: queuecommand called
usb-storage: *** thread awakened.
usb-storage: Command INQUIRY (6 bytes)
usb-storage: 12 00 00 00 24 00
usb-storage: Bulk Command S 0x43425355 T 0x1 L 36 F 128 Trg 0 LUN 0 CL 12
usb-storage: usb_stor_bulk_transfer_buf: xfer 31 bytes
usb-storage: Status code -71; transferred 0/31
usb-storage: -- unknown error
usb-storage: Bulk command transfer result=4
usb-storage: -- transport indicates error, resetting
usb-storage: usb_stor_Bulk_reset called
usb-storage: usb_stor_control_msg: rq=ff rqtype=21 value=0000 index=00
len=0
usb-storage: Soft reset failed: -71
usb-storage: scsi cmd done, result=0x70000
usb-storage: *** thread sleeping.
usb-storage: queuecommand called
usb-storage: *** thread awakened.
usb-storage: Command INQUIRY (6 bytes)
usb-storage: 12 00 00 00 24 00
usb-storage: Bulk Command S 0x43425355 T 0x2 L 36 F 128 Trg 0 LUN 0 CL 12
usb-storage: usb_stor_bulk_transfer_buf: xfer 31 bytes
usb-storage: Status code -71; transferred 0/31
usb-storage: -- unknown error
usb-storage: Bulk command transfer result=4
usb-storage: -- transport indicates error, resetting
usb-storage: usb_stor_Bulk_reset called
usb-storage: usb_stor_control_msg: rq=ff rqtype=21 value=0000 index=00
len=0
usb-storage: Soft reset failed: -71
usb-storage: scsi cmd done, result=0x70000
usb-storage: *** thread sleeping.
usb-storage: queuecommand called
usb-storage: *** thread awakened.
usb-storage: Command INQUIRY (6 bytes)
usb-storage: 12 00 00 00 24 00
usb-storage: Bulk Command S 0x43425355 T 0x3 L 36 F 128 Trg 0 LUN 0 CL 12
usb-storage: usb_stor_bulk_transfer_buf: xfer 31 bytes
usb-storage: Status code -71; transferred 0/31
usb-storage: -- unknown error
usb-storage: Bulk command transfer result=4
usb-storage: -- transport indicates error, resetting
usb-storage: usb_stor_Bulk_reset called
usb-storage: usb_stor_control_msg: rq=ff rqtype=21 value=0000 index=00
len=0
usb-storage: Soft reset failed: -71
usb-storage: scsi cmd done, result=0x70000
usb-storage: *** thread sleeping.
usb-storage: queuecommand called
usb-storage: *** thread awakened.
usb-storage: Bad target number (1:0)
usb-storage: scsi cmd done, result=0x40000
usb-storage: *** thread sleeping.
usb-storage: queuecommand called
usb-storage: *** thread awakened.
usb-storage: Bad target number (2:0)
usb-storage: scsi cmd done, result=0x40000
usb-storage: *** thread sleeping.
usb-storage: queuecommand called
usb-storage: *** thread awakened.
usb-storage: Bad target number (3:0)
usb-storage: scsi cmd done, result=0x40000
usb-storage: *** thread sleeping.
usb-storage: queuecommand called
usb-storage: *** thread awakened.
usb-storage: Bad target number (4:0)
usb-storage: scsi cmd done, result=0x40000
usb-storage: *** thread sleeping.
usb-storage: queuecommand called
usb-storage: *** thread awakened.
usb-storage: Bad target number (5:0)
usb-storage: scsi cmd done, result=0x40000
usb-storage: *** thread sleeping.
usb-storage: queuecommand called
usb-storage: *** thread awakened.
usb-storage: Bad target number (6:0)
usb-storage: scsi cmd done, result=0x40000
usb-storage: *** thread sleeping.
usb-storage: queuecommand called
usb-storage: *** thread awakened.
usb-storage: Bad target number (7:0)
usb-storage: scsi cmd done, result=0x40000
usb-storage: *** thread sleeping.
usb-storage: device scan complete
*
J'en profite au cas où certains d'entre vous aurait un début de
réponse : Savez-vous comment ça se passe pour les portables
(téléphones) avec sortie USB (pour transférer les photos prises par
exemple) sur un motorola? Sous windows il fallait un driver pour
considérer le portable comme un modem mais est-ce la même chose sous
Linux ou le portable est-il considéré comme une clé USB (ce serait
l'idéal)?
Merci d'avance :)
RTyler
P.S. : n'hésitez pas à me demander les informations que j'aurais
oublié de poster pour la bonne compréhension du problème (inutile de
me demander mon mot de passe root ça ne marche pas :-p)