Re: [Re: Sarge, usb, 2.6.3]
Re salut...
Voici les traces du kernel lors d'un branchement de ma cle usb qui
fonctionne...
------------------------------------------------------------------------------------------
Jun 17 23:07:34 localhost kernel: usb 1-1: new full speed USB device
using address 4
Jun 17 23:07:35 localhost kernel: scsi2 : SCSI emulation for USB Mass
Storage devices
Jun 17 23:07:35 localhost kernel: Vendor: Model: USB DISK
2.0 Rev: 1.15
Jun 17 23:07:35 localhost kernel: Type:
Direct-Access ANSI SCSI revision: 02
Jun 17 23:07:35 localhost usb.agent[3339]: usb-storage: already loaded
Jun 17 23:07:35 localhost kernel: SCSI device sda: 253952 512-byte hdwr
sectors (130 MB)
Jun 17 23:07:35 localhost kernel: sda: assuming Write Enabled
Jun 17 23:07:35 localhost kernel: /dev/scsi/host2/bus0/target0/lun0: p1
Jun 17 23:07:35 localhost kernel: Attached scsi removable disk sda at
scsi2, channel 0, id 0, lun 0
Jun 17 23:07:36 localhost scsi.agent[3371]: disk at
/devices/pci0000:00/0000:00:07.2/usb1/1-1/1-1:1.0/host2/2:0:0:0
Jun 17 23:08:16 localhost kernel: usb 1-1: USB disconnect, address 4
------------------------------------------------------------------------------------------
et voic les traces de mon appareil photo numerique qui plante lors du
montage...
------------------------------------------------------------------------------------------
Jun 17 23:09:25 localhost kernel: usb 1-2: new full speed USB device
using address 5
Jun 17 23:09:26 localhost kernel: scsi3 : SCSI emulation for USB Mass
Storage devices
Jun 17 23:09:26 localhost kernel: Vendor: Fujifilm Model: FinePix
1400Zoom Rev: 1000
Jun 17 23:09:26 localhost kernel: Type:
Direct-Access ANSI SCSI revision: 02
Jun 17 23:09:26 localhost usb.agent[3466]: usb-storage: already loaded
Jun 17 23:09:32 localhost kernel: sda : READ CAPACITY failed.
Jun 17 23:09:32 localhost kernel: sda : status=0, message=00, host=7,
driver=00
Jun 17 23:09:32 localhost kernel: sda : sense not available.
Jun 17 23:09:32 localhost kernel: sda: assuming Write Enabled
Jun 17 23:09:32 localhost kernel: sda : READ CAPACITY failed.
Jun 17 23:09:32 localhost kernel: sda : status=0, message=00, host=7,
driver=00
Jun 17 23:09:32 localhost kernel: sda : sense not available.
Jun 17 23:09:32 localhost kernel: sda: assuming Write Enabled
Jun 17 23:09:32 localhost kernel: sda : READ CAPACITY failed.
Jun 17 23:09:32 localhost kernel: sda : status=0, message=00, host=7,
driver=00
Jun 17 23:09:32 localhost kernel: sda : sense not available.
Jun 17 23:09:32 localhost kernel: sda: assuming Write Enabled
Jun 17 23:09:32 localhost kernel:
/dev/scsi/host3/bus0/target0/lun0:<3>Buffer I/O error on device sda,
logical block 0
Jun 17 23:09:32 localhost kernel: unable to read partition table
Jun 17 23:09:32 localhost kernel:
/dev/scsi/host3/bus0/target0/lun0:<3>Buffer I/O error on device sda,
logical block 0
Jun 17 23:09:32 localhost kernel: unable to read partition table
Jun 17 23:09:32 localhost kernel: Attached scsi removable disk sda at
scsi3, channel 0, id 0, lun 0
Jun 17 23:09:33 localhost scsi.agent[3500]: disk at
/devices/pci0000:00/0000:00:07.2/usb1/1-2/1-2:1.0/host3/3:0:0:0
------------------------------------------------------------------------------------------
Les messages d'erruers sont les suivants... et j'arrive pas à comprendre....
Jun 17 23:09:32 localhost kernel: sda : READ CAPACITY failed.
JJun 17 23:09:32 localhost kernel: sda : READ CAPACITY failed.
un 17 23:09:32 localhost kernel: sda : READ CAPACITY failed.
Dans le /proc/scsi/scsi j'ai bien mon APN
------------------------------------------------------------------------------------------
# cat /proc/scsi/scsi
Attached devices:
Host: scsi5 Channel: 00 Id: 00 Lun: 00
Vendor: Fujifilm Model: FinePix 1400Zoom Rev: 1000
Type: Direct-Access ANSI SCSI revision: 02
------------------------------------------------------------------------------------------
merci de votre aide, bonne soirée
david
Reply to: