Sarge, usb, 2.6.3
Bonjour la liste... je viens d'installer une sarge avec un noyau 2.6.3
et je voudrasi acceder à mon appareil photo numerique (apn) via l'usb...
par contre j'accede bien à ma clef usb sur /dev/sda1
voici le resultat quand je tnete de monter le port usb de mon apn....
---------------------------------------------------------------------------------------------------------------------------------------------------------------------
# mount /dev/sda /mnt/usb/
mount: /dev/sda is not a valid block device
# mount /dev/sda1 /mnt/usb/
mount: /dev/sda1 is not a valid block device
---------------------------------------------------------------------------------------------------------------------------------------------------------------------
Merci de votre aide et bonne journée
voici les infos :
Messages du noyau
---------------------------------------------------------------------------------------------------------------------------------------------------------------------
Jun 9 09:14:16 localhost kernel: usb 1-2: new full speed USB device
using address 3
Jun 9 09:14:16 localhost kernel: scsi1 : SCSI emulation for USB Mass
Storage devices
Jun 9 09:14:16 localhost kernel: Vendor: Fujifilm Model: FinePix
1400Zoom Rev: 1000
Jun 9 09:14:16 localhost kernel: Type:
Direct-Access ANSI SCSI revision: 02
Jun 9 09:14:17 localhost usb.agent[2592]: usb-storage: already loaded
Jun 9 09:14:23 localhost kernel: sda : READ CAPACITY failed.
Jun 9 09:14:23 localhost kernel: sda : status=0, message=00, host=7,
driver=00
Jun 9 09:14:23 localhost kernel: sda : sense not available.
Jun 9 09:14:23 localhost kernel: sda: assuming Write Enabled
Jun 9 09:14:23 localhost kernel: sda : READ CAPACITY failed.
Jun 9 09:14:23 localhost kernel: sda : status=0, message=00, host=7,
driver=00
Jun 9 09:14:23 localhost kernel: sda : sense not available.
Jun 9 09:14:23 localhost kernel: sda: assuming Write Enabled
Jun 9 09:14:23 localhost kernel: sda : READ CAPACITY failed.
Jun 9 09:14:23 localhost kernel: sda : status=0, message=00, host=7,
driver=00
Jun 9 09:14:23 localhost kernel: sda : sense not available.
Jun 9 09:14:23 localhost kernel: sda: assuming Write Enabled
Jun 9 09:14:23 localhost kernel:
/dev/scsi/host1/bus0/target0/lun0:<3>Buffer I/O error on device sda,
logical block 0
Jun 9 09:14:23 localhost kernel: unable to read partition table
Jun 9 09:14:23 localhost kernel:
/dev/scsi/host1/bus0/target0/lun0:<3>Buffer I/O error on device sda,
logical block 0
Jun 9 09:14:23 localhost kernel: unable to read partition table
Jun 9 09:14:23 localhost kernel: Attached scsi removable disk sda at
scsi1, channel 0, id 0, lun 0
Jun 9 09:14:23 localhost scsi.agent[2615]: disk at
/devices/pci0000:00/0000:00:07.2/usb1/1-2/1-2:1.0/host1/1:0:0:0
---------------------------------------------------------------------------------------------------------------------------------------------------------------------
Les modules
---------------------------------------------------------------------------------------------------------------------------------------------------------------------
# lsmod | grep usb
usb_storage 58432 0
scsi_mod 109112 2 sd_mod,usb_storage
usbcore 94044 4 usb_storage,uhci_hcd
ide_core 141804 6
usb_storage,ide_cd,ide_disk,ide_generic,ide_detect,via82cxxx
# lsmod | grep scsi
scsi_mod 109112 2 sd_mod,usb_storage
---------------------------------------------------------------------------------------------------------------------------------------------------------------------
Reply to: