2 questions: X et bash
Re-bonjour.
Voici ces 2 questions:
1) pourquoi ais-je les lignes suivantes dans /var/log/XFree86.0.log
(II) SIS(0): Supported additional Video Mode:
(II) SIS(0): clock: 108.0 MHz Image Size: 306 x 230 mm
(II) SIS(0): h_active: 1280 h_sync: 1328 h_sync_end 1440 h_blank_end
1688 h_border: 0
(II) SIS(0): v_active: 1024 v_sync: 1025 v_sync_end 1028 v_blanking:
1066 v_border: 0
(II) SIS(0): Serial No: HD 000116
(II) SIS(0): Monitor name: PHILIPS 107E
(II) SIS(0): Ranges: V min: 50 V max: 120 Hz, H min: 30 H max: 70 kHz,
PixClock max 110 MHz
(--) SIS(0): End of CRT1 DDC monitor info ******************************
(==) SIS(0): Min pixel clock is 12 MHz
(--) SIS(0): Max pixel clock is 390 MHz
(II) SIS(0): Replaced entire mode list with built-in modes
(II) SIS(0): "Unknown reason" in the following list means that the mode
(II) SIS(0): is not supported on the chipset/bridge/current output
device.
(II) SIS(0): philips 107e: Using hsync range of 30.00-70.00 kHz
(II) SIS(0): philips 107e: Using vrefresh range of 50.00-120.00 Hz
(II) SIS(0): Clock range: 12.00 to 390.00 MHz
(II) SIS(0): Not using default mode "800x600" (hsync out of range)
(II) SIS(0): Not using default mode "800x600" (hsync out of range)
(II) SIS(0): Not using default mode "640x480" (hsync out of range)
(II) SIS(0): Not using default mode "640x480" (hsync out of range)
(II) SIS(0): Not using default mode "1024x768" (hsync out of range)
(II) SIS(0): Not using default mode "1024x768" (hsync out of range)
(II) SIS(0): Not using default mode "1280x1024" (hsync out of range)
(II) SIS(0): Not using default mode "1280x1024" (hsync out of range)
(II) SIS(0): Not using default mode "1600x1200" (hsync out of range)
(II) SIS(0): Not using default mode "1600x1200" (hsync out of range)
(II) SIS(0): Not using default mode "1600x1200" (hsync out of range)
(II) SIS(0): Not using default mode "1600x1200" (hsync out of range)
(II) SIS(0): Not using default mode "1600x1200" (hsync out of range)
(II) SIS(0): Not using default mode "1600x1200" (hsync out of range)
(II) SIS(0): Not using default mode "1600x1200" (hsync out of range)
(II) SIS(0): Not using default mode "1920x1440" (hsync out of range)
(II) SIS(0): Not using default mode "1920x1440" (hsync out of range)
(II) SIS(0): Not using default mode "1920x1440" (hsync out of range)
(II) SIS(0): Not using default mode "1920x1440" (hsync out of range)
(II) SIS(0): Not using default mode "1920x1440" (hsync out of range)
(II) SIS(0): Not using default mode "1920x1440" (hsync out of range)
(II) SIS(0): Not using default mode "2048x1536" (hsync out of range)
(II) SIS(0): Not using default mode "2048x1536" (hsync out of range)
(II) SIS(0): Not using default mode "2048x1536" (hsync out of range)
(II) SIS(0): Not using default mode "2048x1536" (hsync out of range)
(II) SIS(0): Not using default mode "2048x1536" (hsync out of range)
(II) SIS(0): Not using default mode "1280x720" (hsync out of range)
(II) SIS(0): Not using default mode "1280x720" (hsync out of range)
(II) SIS(0): Not using default mode "1280x960" (hsync out of range)
(WW) (1400x1050,philips 107e) mode clock 122.896MHz exceeds DDC maximum
110MHz
(II) SIS(0): Not using default mode "1400x1050" (hsync out of range)
(II) SIS(0): Not using default mode "1152x864" (hsync out of range)
(--) SIS(0): Virtual size is 1280x1024 (pitch 1280)
(**) SIS(0): Default mode "1280x1024": 107.9 MHz, 63.9 kHz, 59.9 Hz
(II) SIS(0): Modeline "1280x1024" 107.86 1280 1328 1440 1688 1024
1025 1028 1066 +hsync +vsync
(**) SIS(0): Default mode "800x600": 68.2 MHz, 63.6 kHz, 100.0 Hz
(II) SIS(0): Modeline "800x600" 68.18 800 848 936 1072 600 601 604
636 +hsync +vsync
(**) SIS(0): Default mode "640x480": 52.4 MHz, 61.7 kHz, 119.9 Hz
(II) SIS(0): Modeline "640x480" 52.35 640 680 744 848 480 481 484
515 -hsync -vsync
(++) SIS(0): DPI set to (100, 100)
C'est les "hsync out of range" qui me tarabustent; et je peux charger X
sans problème en 1240x1024.
2) Comment faire dans le bash pour avoir avec 'less' le % restant à lire
dans un fichier texte? Car c'est bien pratique.
Merci
--
Pour me répondre, enlever le 'anti-spam' de l'adresse, merci.
Reply to: