Bug#219375: installation-reports - Hard drive not detected
Package: installation-reports
Debian-installer-version: October 2003. (I don't know how to get the version from the cd in my hand!)
uname -a: Linux (none) 2.4.22-1-386 #5 Sun Sep 28 13:21:31 EST 2003 i686 unknown
prompt: BusyBox v1.00-pre3 (2003.09.36-13:15+000) Built-in shell (ash)
Method: Burned and booted from "/dev/hdc" http://gluck.debian.org/cdimage/testing/netinst/i386/sarge-i386-netinst.iso
boot=linux (default) (not using "boot: net")
Processor: Pentium III 300MHz
Root Device: IBM-DPTA-372050, UDMA 4, aka "/dev/hde"
Mother board: 07/05/2000-i440BX-W83977-2A69KA1UC-TH
Award bios v4.51PG
Award Plug and play bios extension v1.0A
-> Detected DVD ROM Hitachi on secondary master
HPT366 bios ver 1.25
-> Primary Master C: IBM-DPTA-372050 .... UDMA 4
Adaptec AHA-2940 BIOS v1.21
-> SCSI 4:0 plextor CD-R PX-W1210S
Output of lspci: (long version because of problems with ide0/ide1/ide2/ide3).
---------------------
00:00.0 Host bridge: Intel Corp. 440BX/ZX/DX - 82443BX/ZX/DX Host bridge (rev 03)
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
Status: Cap+ 66Mhz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort+ >SERR- <PERR-
Latency: 32
Region 0: Memory at d0000000 (32-bit, prefetchable) [size=64M]
Capabilities: [a0] AGP version 1.0
Status: RQ=32 Iso- ArqSz=0 Cal=0 SBA+ ITACoh- GART64- HTrans- 64bit- FW- AGP3- Rate=x1,x2
Command: RQ=1 ArqSz=0 Cal=0 SBA+ AGP+ GART64- 64bit- FW- Rate=x2
00:01.0 PCI bridge: Intel Corp. 440BX/ZX/DX - 82443BX/ZX/DX AGP bridge (rev 03) (prog-if 00 [Normal decode])
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR+ FastB2B-
Status: Cap- 66Mhz+ UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
Latency: 64
Bus: primary=00, secondary=01, subordinate=01, sec-latency=32
I/O behind bridge: 00009000-00009fff
Memory behind bridge: d8000000-d9ffffff
Prefetchable memory behind bridge: d4000000-d7ffffff
BridgeCtl: Parity- SERR- NoISA- VGA+ MAbort- >Reset- FastB2B+
00:07.0 ISA bridge: Intel Corp. 82371AB/EB/MB PIIX4 ISA (rev 02)
Control: I/O+ Mem+ BusMaster+ SpecCycle+ MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
Status: Cap- 66Mhz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
Latency: 0
00:07.1 IDE interface: Intel Corp. 82371AB/EB/MB PIIX4 IDE (rev 01) (prog-if 80 [Master])
Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
Status: Cap- 66Mhz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
Latency: 32
Region 4: I/O ports at f000 [size=16]
00:07.2 USB Controller: Intel Corp. 82371AB/EB/MB PIIX4 USB (rev 01) (prog-if 00 [UHCI])
Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
Status: Cap- 66Mhz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
Latency: 32
Interrupt: pin D routed to IRQ 9
Region 4: I/O ports at a000 [size=32]
00:07.3 Bridge: Intel Corp. 82371AB/EB/MB PIIX4 ACPI (rev 02)
Control: I/O+ Mem+ BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
Status: Cap- 66Mhz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
Interrupt: pin ? routed to IRQ 9
00:09.0 Ethernet controller: Realtek Semiconductor Co., Ltd. RTL-8139/8139C/8139C+ (rev 10)
Subsystem: Realtek Semiconductor Co., Ltd. RT8139
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
Status: Cap+ 66Mhz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
Latency: 32 (8000ns min, 16000ns max)
Interrupt: pin A routed to IRQ 9
Region 0: I/O ports at a400 [size=256]
Region 1: Memory at db000000 (32-bit, non-prefetchable) [size=256]
Expansion ROM at <unassigned> [disabled] [size=64K]
Capabilities: [50] Power Management version 2
Flags: PMEClk- DSI- D1+ D2+ AuxCurrent=375mA PME(D0-,D1+,D2+,D3hot+,D3cold+)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-
00:0b.0 Multimedia video controller: Brooktree Corporation Bt848 Video Capture (rev 12)
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
Status: Cap- 66Mhz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
Latency: 32 (4000ns min, 10000ns max)
Interrupt: pin A routed to IRQ 11
Region 0: Memory at db001000 (32-bit, prefetchable) [size=4K]
00:0d.0 Multimedia audio controller: Ensoniq ES1371 [AudioPCI-97] (rev 08)
Subsystem: Ensoniq Creative Sound Blaster AudioPCI64V, AudioPCI128
Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR+ FastB2B-
Status: Cap+ 66Mhz- UDF- FastB2B- ParErr- DEVSEL=slow >TAbort- <TAbort- <MAbort- >SERR- <PERR-
Latency: 32 (3000ns min, 32000ns max)
Interrupt: pin A routed to IRQ 9
Region 0: I/O ports at a800 [size=64]
Capabilities: [dc] Power Management version 1
Flags: PMEClk- DSI+ D1- D2+ AuxCurrent=0mA PME(D0-,D1-,D2-,D3hot-,D3cold-)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-
00:0f.0 SCSI storage controller: Adaptec AHA-2940/2940W / AIC-7871 (rev 03)
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
Status: Cap- 66Mhz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
Latency: 32 (2000ns min, 2000ns max), Cache Line Size: 0x08 (32 bytes)
Interrupt: pin A routed to IRQ 10
Region 0: I/O ports at ac00 [disabled] [size=256]
Region 1: Memory at db002000 (32-bit, non-prefetchable) [size=4K]
Expansion ROM at <unassigned> [disabled] [size=64K]
00:13.0 Unknown mass storage controller: Triones Technologies, Inc. HPT366/368/370/370A/372 (rev 01)
Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
Status: Cap- 66Mhz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
Latency: 120 (2000ns min, 2000ns max), Cache Line Size: 0x08 (32 bytes)
Interrupt: pin A routed to IRQ 11
Region 0: I/O ports at b000 [size=8]
Region 1: I/O ports at b400 [size=4]
Region 4: I/O ports at b800 [size=256]
Expansion ROM at <unassigned> [disabled] [size=128K]
00:13.1 Unknown mass storage controller: Triones Technologies, Inc. HPT366/368/370/370A/372 (rev 01)
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
Status: Cap- 66Mhz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
Latency: 120 (2000ns min, 2000ns max), Cache Line Size: 0x08 (32 bytes)
Interrupt: pin B routed to IRQ 11
Region 0: I/O ports at bc00 [size=8]
Region 1: I/O ports at c000 [size=4]
Region 4: I/O ports at c400 [size=256]
01:00.0 VGA compatible controller: ATI Technologies Inc Rage 128 RF/SG AGP (prog-if 00 [VGA])
Subsystem: ATI Technologies Inc: Unknown device 0048
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping+ SERR- FastB2B-
Status: Cap+ 66Mhz+ UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
Latency: 32 (2000ns min), Cache Line Size: 0x08 (32 bytes)
Interrupt: pin A routed to IRQ 10
Region 0: Memory at d4000000 (32-bit, prefetchable) [size=64M]
Region 1: I/O ports at 9000 [size=256]
Region 2: Memory at d9000000 (32-bit, non-prefetchable) [size=16K]
Expansion ROM at <unassigned> [disabled] [size=128K]
Capabilities: [50] AGP version 2.0
Status: RQ=32 Iso- ArqSz=0 Cal=0 SBA+ ITACoh- GART64- HTrans- 64bit- FW- AGP3- Rate=x1,x2
Command: RQ=32 ArqSz=0 Cal=0 SBA+ AGP+ GART64- 64bit- FW- Rate=x2
Capabilities: [5c] Power Management version 1
Flags: PMEClk- DSI- D1+ D2- AuxCurrent=0mA PME(D0-,D1-,D2-,D3hot-,D3cold-)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-
---------------------
Base System Installation Checklist:
Initial boot worked: [O]
Configure network HW: [O]
Config network: [O]
Detect CD: [O]
Load installer modules: [O]
Detect hard drives: [E]
Partition hard drives: [ ]
Create file systems: [ ]
Mount partitions: [ ]
Install base system: [ ]
Install boot loader: [ ]
Reboot: [ ]
[O] = OK, [E] = Error (please elaborate below), [ ] = didn't try it
Comments/Problems:
My hard drive was not detected because of conflicts between basic ide (ide0/ide1 with cdrom) and extended ide (htp366 aka ide2/ide3 with hard drive).
I kept trying for many hours and finally found that workaround:
- When prompted for language "Choose this to proceed in English (USA)" (and not later!), switch to console (Alt+F2)
- Enter this
insmod ide-code
insmod ide-disk
insmod piix
insmod htp366
- Resume normal installation
If you insmod piix and htp366 when you really need it "Hard drive not found", then the hard drive is not detected.
After you boot a downloaded debian pre-built kernel, you can forget all that. Everything works fine! :)
It's a pity it can't be that simple after burning the CD!
FYI, I tried to install 2.6.0-test9: htp366 decided to load before piix, so that ide0/ide1 and ide2/ide3 are switched. It doesn't boot... But that's another story... :(
Reply to: