Ответ: Страшное зависание системы от работы CD-привода
Вот такой ужос:
dmesg
[ 0.000000] Initializing cgroup subsys cpuset
[ 0.000000] Initializing cgroup subsys cpu
[ 0.000000] Linux version 2.6.26-1-686 (Debian 2.6.26-13)
(waldi@debian.org) (gcc version 4.1.3 20080704 (prerelease) (Debian
4.1.2-24)) #1 SMP Sat Jan 10 18:29:31 UTC 2009
[ 0.000000] BIOS-provided physical RAM map:
[ 0.000000] BIOS-e820: 0000000000000000 - 000000000009fc00 (usable)
[ 0.000000] BIOS-e820: 000000000009fc00 - 00000000000a0000 (reserved)
[ 0.000000] BIOS-e820: 00000000000e0000 - 0000000000100000 (reserved)
[ 0.000000] BIOS-e820: 0000000000100000 - 0000000006ff0000 (usable)
[ 0.000000] BIOS-e820: 0000000006ff0000 - 0000000006ffffc0 (ACPI data)
[ 0.000000] BIOS-e820: 0000000006ffffc0 - 0000000007000000 (ACPI NVS)
[ 0.000000] BIOS-e820: 00000000fff80000 - 0000000100000000 (reserved)
[ 0.000000] 0MB HIGHMEM available.
[ 0.000000] 111MB LOWMEM available.
[ 0.000000] Entering add_active_range(0, 0, 28656) 0 entries of 256 used
[ 0.000000] Zone PFN ranges:
[ 0.000000] DMA 0 -> 4096
[ 0.000000] Normal 4096 -> 28656
[ 0.000000] HighMem 28656 -> 28656
[ 0.000000] Movable zone start PFN for each node
[ 0.000000] early_node_map[1] active PFN ranges
[ 0.000000] 0: 0 -> 28656
[ 0.000000] On node 0 totalpages: 28656
[ 0.000000] DMA zone: 32 pages used for memmap
[ 0.000000] DMA zone: 0 pages reserved
[ 0.000000] DMA zone: 4064 pages, LIFO batch:0
[ 0.000000] Normal zone: 192 pages used for memmap
[ 0.000000] Normal zone: 24368 pages, LIFO batch:3
[ 0.000000] HighMem zone: 0 pages used for memmap
[ 0.000000] Movable zone: 0 pages used for memmap
[ 0.000000] DMI 2.3 present.
[ 0.000000] ACPI: RSDP 000E5010, 0014 (r0 OID_00)
[ 0.000000] ACPI: RSDT 06FFFBC0, 0030 (r1 INSYDE RSDT_000 1
_CSI 10101)
[ 0.000000] ACPI: FACP 06FFFAC0, 0074 (r1 INSYDE FACP_000 100
_CSI 10101)
[ 0.000000] ACPI Warning (tbfadt-0442): Optional field "Gpe1Block"
has zero address or length: 0000000000001050/0 [20080321]
[ 0.000000] ACPI: DSDT 06FFB470, 464E (r1 FUJITS EF3 416
MSFT 100000D)
[ 0.000000] ACPI: FACS 06FFFFC0, 0040
[ 0.000000] ACPI: BOOT 06FFFB50, 0028 (r1 INSYDE SYS_BOOT 100
_CSI 10101)
[ 0.000000] ACPI: DBGP 06FFFB80, 0034 (r1 INSYDE DBGP_000 100
_CSI 10101)
[ 0.000000] ACPI: DMI detected: Fujitsu Siemens
[ 0.000000] ACPI: PM-Timer IO Port: 0x1008
[ 0.000000] Allocating PCI resources starting at 10000000 (gap:
07000000:f8f80000)
[ 0.000000] PM: Registered nosave memory: 000000000009f000 - 00000000000a0000
[ 0.000000] PM: Registered nosave memory: 00000000000a0000 - 00000000000e0000
[ 0.000000] PM: Registered nosave memory: 00000000000e0000 - 0000000000100000
[ 0.000000] SMP: Allowing 0 CPUs, 0 hotplug CPUs
[ 0.000000] PERCPU: Allocating 37960 bytes of per cpu data
[ 0.000000] NR_CPUS: 8, nr_cpu_ids: 1
[ 0.000000] Built 1 zonelists in Zone order, mobility grouping on.
Total pages: 28432
[ 0.000000] Kernel command line: root=/dev/mapper/bariyat-root ro quiet
[ 0.000000] Local APIC disabled by BIOS -- you can enable it with "lapic"
[ 0.000000] mapped APIC to ffffb000 (010ec000)
[ 0.000000] Enabling fast FPU save and restore... done.
[ 0.000000] Enabling unmasked SIMD FPU exception support... done.
[ 0.000000] Initializing CPU#0
[ 0.000000] PID hash table entries: 512 (order: 9, 2048 bytes)
[ 0.000000] Detected 1069.106 MHz processor.
[ 0.004000] Console: colour VGA+ 80x25
[ 0.004000] console [tty0] enabled
[ 0.004000] Dentry cache hash table entries: 16384 (order: 4, 65536 bytes)
[ 0.004000] Inode-cache hash table entries: 8192 (order: 3, 32768 bytes)
[ 0.004000] Memory: 103032k/114624k available (1769k kernel code,
11140k reserved, 752k data, 244k init, 0k highmem)
[ 0.004000] virtual kernel memory layout:
[ 0.004000] fixmap : 0xfff4c000 - 0xfffff000 ( 716 kB)
[ 0.004000] pkmap : 0xff800000 - 0xffc00000 (4096 kB)
[ 0.004000] vmalloc : 0xc7800000 - 0xff7fe000 ( 895 MB)
[ 0.004000] lowmem : 0xc0000000 - 0xc6ff0000 ( 111 MB)
[ 0.004000] .init : 0xc037f000 - 0xc03bc000 ( 244 kB)
[ 0.004000] .data : 0xc02ba4ab - 0xc0376620 ( 752 kB)
[ 0.004000] .text : 0xc0100000 - 0xc02ba4ab (1769 kB)
[ 0.004000] Checking if this processor honours the WP bit even in
supervisor mode...Ok.
[ 0.004000] CPA: page pool initialized 1 of 1 pages preallocated
[ 0.084221] Calibrating delay using timer specific routine..
2140.89 BogoMIPS (lpj=4281793)
[ 0.084298] Security Framework initialized
[ 0.084311] SELinux: Disabled at boot.
[ 0.084318] Capability LSM initialized
[ 0.084353] Mount-cache hash table entries: 512
[ 0.084631] Initializing cgroup subsys ns
[ 0.084640] Initializing cgroup subsys cpuacct
[ 0.084646] Initializing cgroup subsys devices
[ 0.084684] CPU: L1 I cache: 16K, L1 D cache: 16K
[ 0.084691] CPU: L2 cache: 256K
[ 0.084698] Intel machine check architecture supported.
[ 0.084706] Intel machine check reporting enabled on CPU#0.
[ 0.084727] Checking 'hlt' instruction... OK.
[ 0.100541] SMP alternatives: switching to UP code
[ 0.109029] Freeing SMP alternatives: 16k freed
[ 0.109043] ACPI: Core revision 20080321
[ 0.118789] ACPI: setting ELCR to 0200 (from 0400)
[ 0.124038] weird, boot CPU (#0) not listedby the BIOS.
[ 0.124044] SMP motherboard not detected.
[ 0.124049] Local APIC not detected. Using dummy APIC emulation.
[ 0.124054] SMP disabled
[ 0.124185] Brought up 1 CPUs
[ 0.124192] Total of 1 processors activated (2140.89 BogoMIPS).
[ 0.124211] CPU0 attaching sched-domain:
[ 0.124217] domain 0: span 0
[ 0.124222] groups: 0
[ 0.124736] net_namespace: 660 bytes
[ 0.124756] Booting paravirtualized kernel on bare hardware
[ 0.125343] NET: Registered protocol family 16
[ 0.125881] ACPI: bus type pci registered
[ 0.126156] PCI: PCI BIOS revision 2.10 entry at 0xe8944, last bus=1
[ 0.126163] PCI: Using configuration type 1 for base access
[ 0.126188] Setting up standard PCI resources
[ 0.131235] ACPI: EC: Look up EC in DSDT
[ 0.852031] ACPI: Interpreter enabled
[ 0.852031] ACPI: (supports S0 S3 S4 S5)
[ 0.852031] ACPI: Using PIC for interrupt routing
[ 0.852031] ACPI: EC: non-query interrupt received, switching to
interrupt mode
[ 0.879224] ACPI: EC: GPE = 0x1, I/O: command/status = 0x66, data = 0x62
[ 0.879235] ACPI: EC: driver started in interrupt mode
[ 0.879345] ACPI: PCI Root Bridge [PCI0] (0000:00)
[ 0.880226] ACPI: PCI Interrupt Routing Table [\_SB_.PCI0._PRT]
[ 0.891962] ACPI: PCI Interrupt Link [LNKA] (IRQs 3 4 7 9 14 15) *10
[ 0.892340] ACPI: PCI Interrupt Link [LNKB] (IRQs 3 4 7 *9 14 15)
[ 0.892596] ACPI: PCI Interrupt Link [LNKC] (IRQs 3 4 7 *10 14 15)
[ 0.892853] ACPI: PCI Interrupt Link [LNKD] (IRQs 3 4 7 *9 14 15)
[ 0.893188] ACPI: Power Resource [PFAN] (off)
[ 0.893357] Linux Plug and Play Support v0.97 (c) Adam Belay
[ 0.893436] pnp: PnP ACPI init
[ 0.893462] ACPI: bus type pnp registered
[ 0.905118] PCI: setting IRQ 13 as level-triggered
[ 0.909589] pnp: PnP ACPI: found 13 devices
[ 0.909599] ACPI: ACPI bus type pnp unregistered
[ 0.909610] PnPBIOS: Disabled by ACPI PNP
[ 0.910308] PCI: Using ACPI for IRQ routing
[ 0.910776] ACPI: RTC can wake from S4
[ 0.910862] system 00:03: iomem range 0xfffc0000-0xffffffff could
not be reserved
[ 0.910886] system 00:05: ioport range 0x4d0-0x4d1 has been reserved
[ 0.910893] system 00:05: ioport range 0x1000-0x107f has been reserved
[ 0.910899] system 00:05: ioport range 0x1400-0x147f has been reserved
[ 0.941940] PCI: Bridge: 0000:00:01.0
[ 0.941947] IO window: c000-dfff
[ 0.941954] MEM window: 0xe0000000-0xefffffff
[ 0.941961] PREFETCH window: 0x0000000090000000-0x000000009fffffff
[ 0.941969] PCI: Bus 2, cardbus bridge: 0000:00:0a.0
[ 0.941974] IO window: 0x00001800-0x000018ff
[ 0.941981] IO window: 0x00001c00-0x00001cff
[ 0.941987] PREFETCH window: 0x10000000-0x13ffffff
[ 0.941992] MEM window: 0x14000000-0x17ffffff
[ 0.941999] PCI: Bus 6, cardbus bridge: 0000:00:0a.1
[ 0.942003] IO window: 0x00002000-0x000020ff
[ 0.942009] IO window: 0x00002400-0x000024ff
[ 0.942015] PREFETCH window: 0x18000000-0x1bffffff
[ 0.942021] MEM window: 0x1c000000-0x1fffffff
[ 0.942058] PCI: Setting latency timer of device 0000:00:01.0 to 64
[ 0.942707] ACPI: PCI Interrupt Link [LNKA] enabled at IRQ 9
[ 0.942715] PCI: setting IRQ 9 as level-triggered
[ 0.942720] ACPI: PCI Interrupt 0000:00:0a.0[A] -> Link [LNKA] ->
GSI 9 (level, low) -> IRQ 9
[ 0.943091] ACPI: PCI Interrupt Link [LNKB] enabled at IRQ 9
[ 0.943096] ACPI: PCI Interrupt 0000:00:0a.1[B] -> Link [LNKB] ->
GSI 9 (level, low) -> IRQ 9
[ 0.943181] NET: Registered protocol family 2
[ 0.943467] IP route cache hash table entries: 1024 (order: 0, 4096 bytes)
[ 0.943953] TCP established hash table entries: 4096 (order: 3, 32768 bytes)
[ 0.944102] TCP bind hash table entries: 4096 (order: 3, 32768 bytes)
[ 0.944208] TCP: Hash tables configured (established 4096 bind 4096)
[ 0.944215] TCP reno registered
[ 0.944416] NET: Registered protocol family 1
[ 0.944711] checking if image is initramfs...<7>Switched to high
resolution mode on CPU 0
[ 1.511647] it is
[ 2.218180] Freeing initrd memory: 6832k freed
[ 2.218714] Simple Boot Flag at 0x37 set to 0x1
[ 2.219670] audit: initializing netlink socket (disabled)
[ 2.219708] type=2000 audit(1237373091.216:1): initialized
[ 2.219965] Total HugeTLB memory allocated, 0
[ 2.220243] VFS: Disk quotas dquot_6.5.1
[ 2.220315] Dquot-cache hash table entries: 1024 (order 0, 4096 bytes)
[ 2.220414] msgmni has been set to 214
[ 2.220749] Block layer SCSI generic (bsg) driver version 0.4
loaded (major 253)
[ 2.220758] io scheduler noop registered
[ 2.220763] io scheduler anticipatory registered
[ 2.220767] io scheduler deadline registered
[ 2.220794] io scheduler cfq registered (default)
[ 2.220818] PCI: VIA PCI bridge detected.Disabling DAC.
[ 2.220883] pci 0000:01:00.0: Boot video device
[ 2.221642] isapnp: Scanning for PnP cards...
[ 2.575562] isapnp: No Plug & Play device found
[ 2.582697] Serial: 8250/16550 driver $Revision: 1.90 $ 4 ports,
IRQ sharing enabled
[ 2.582928] serial8250: ttyS0 at I/O 0x3f8 (irq = 4) is a 16550A
[ 2.583840] 00:0b: ttyS0 at I/O 0x3f8 (irq = 4) is a 16550A
[ 2.587306] brd: module loaded
[ 2.587569] PNP: PS/2 Controller [PNP0303:KBC,PNP0f13:PS2M] at
0x60,0x64 irq 1,12
[ 2.604895] i8042.c: Detected active multiplexing controller, rev 1.1.
[ 2.615851] serio: i8042 KBD port at 0x60,0x64 irq 1
[ 2.615864] serio: i8042 AUX0 port at 0x60,0x64 irq 12
[ 2.615870] serio: i8042 AUX1 port at 0x60,0x64 irq 12
[ 2.615876] serio: i8042 AUX2 port at 0x60,0x64 irq 12
[ 2.615890] serio: i8042 AUX3 port at 0x60,0x64 irq 12
[ 2.616401] mice: PS/2 mouse device common for all mice
[ 2.616875] rtc_cmos 00:01: rtc core: registered rtc_cmos as rtc0
[ 2.616875] rtc0: alarms up to one year, y3k
[ 2.616875] cpuidle: using governor ladder
[ 2.616875] cpuidle: using governor menu
[ 2.616875] No iBFT detected.
[ 2.617962] TCP cubic registered
[ 2.617970] NET: Registered protocol family 17
[ 2.617985] Using IPI No-Shortcut mode
[ 2.618566] registered taskstats version 1
[ 2.618855] rtc_cmos 00:01: setting system clock to 2009-03-18
10:44:52 UTC (1237373092)
[ 2.619289] Freeing unused kernel memory: 244k freed
[ 2.653769] input: AT Translated Set 2 keyboard as /class/input/input0
[ 2.830552] ACPI: Transitioning device [FAN0] to D3
[ 2.830697] ACPI: PNP0C0B:00 is registered as cooling_device0
[ 2.830709] ACPI: Fan [FAN0] (off)
[ 2.845395] ACPI: CPU0 (power states: C1[C1] C2[C2])
[ 2.845515] ACPI: ACPI0007:00 is registered as cooling_device1
[ 2.845525] ACPI: Processor [CPU0] (supports 16 throttling states)
[ 2.850706] Marking TSC unstable due to: TSC halts in idle.
[ 2.852163] ACPI: LNXTHERM:01 is registered as thermal_zone0
[ 2.853776] ACPI: Thermal Zone [TZN0] (35 C)
[ 3.745063] ACPI: PCI Interrupt 0000:00:0b.0[A] -> Link [LNKA] ->
GSI 9 (level, low) -> IRQ 9
[ 3.794991] ohci1394: fw-host0: OHCI-1394 1.1 (PCI): IRQ=[9]
MMIO=[f0000000-f00007ff] Max Packet=[2048] IR/IT contexts=[4/8]
[ 3.875646] 8139too Fast Ethernet driver 0.9.28
[ 4.084323] ACPI: PCI Interrupt Link [LNKC] enabled at IRQ 10
[ 4.084334] PCI: setting IRQ 10 as level-triggered
[ 4.084341] ACPI: PCI Interrupt 0000:00:0d.0[A] -> Link [LNKC] ->
GSI 10 (level, low) -> IRQ 10
[ 4.085116] eth0: RealTek RTL8139 at 0xe300, 00:e0:00:97:51:d9, IRQ 10
[ 4.085122] eth0: Identified 8139 chip type 'RTL-8139C'
[ 4.090033] 8139cp: 10/100 PCI Ethernet driver v1.3 (Mar 22, 2004)
[ 4.244329] ACPI: ACPI Dock Station Driver
[ 4.637717] SCSI subsystem initialized
[ 4.672926] usbcore: registered new interface driver usbfs
[ 4.672984] usbcore: registered new interface driver hub
[ 4.673058] usbcore: registered new device driver usb
[ 4.676578] USB Universal Host Controller Interface driver v3.0
[ 4.677247] ACPI: PCI Interrupt Link [LNKD] enabled at IRQ 9
[ 4.677256] ACPI: PCI Interrupt 0000:00:11.2[D] -> Link [LNKD] ->
GSI 9 (level, low) -> IRQ 9
[ 4.677280] uhci_hcd 0000:00:11.2: UHCI Host Controller
[ 4.677574] uhci_hcd 0000:00:11.2: new USB bus registered, assigned
bus number 1
[ 4.677621] uhci_hcd 0000:00:11.2: irq 9, io base 0x00001200
[ 4.677848] usb usb1: configuration #1 chosen from 1 choice
[ 4.677914] hub 1-0:1.0: USB hub found
[ 4.677932] hub 1-0:1.0: 2 ports detected
[ 4.780418] usb usb1: New USB device found, idVendor=1d6b, idProduct=0001
[ 4.780429] usb usb1: New USB device strings: Mfr=3, Product=2,
SerialNumber=1
[ 4.780435] usb usb1: Product: UHCI Host Controller
[ 4.780440] usb usb1: Manufacturer: Linux 2.6.26-1-686 uhci_hcd
[ 4.780445] usb usb1: SerialNumber: 0000:00:11.2
[ 4.780541] ACPI: PCI Interrupt 0000:00:11.3[D] -> Link [LNKD] ->
GSI 9 (level, low) -> IRQ 9
[ 4.780565] uhci_hcd 0000:00:11.3: UHCI Host Controller
[ 4.780629] uhci_hcd 0000:00:11.3: new USB bus registered, assigned
bus number 2
[ 4.780673] uhci_hcd 0000:00:11.3: irq 9, io base 0x00001300
[ 4.780861] usb usb2: configuration #1 chosen from 1 choice
[ 4.780932] hub 2-0:1.0: USB hub found
[ 4.780950] hub 2-0:1.0: 2 ports detected
[ 4.832591] libata version 3.00 loaded.
[ 4.884410] usb usb2: New USB device found, idVendor=1d6b, idProduct=0001
[ 4.884422] usb usb2: New USB device strings: Mfr=3, Product=2,
SerialNumber=1
[ 4.884428] usb usb2: Product: UHCI Host Controller
[ 4.884432] usb usb2: Manufacturer: Linux 2.6.26-1-686 uhci_hcd
[ 4.884437] usb usb2: SerialNumber: 0000:00:11.3
[ 4.940083] Uniform Multi-Platform E-IDE driver
[ 4.940097] ide: Assuming 33MHz system bus speed for PIO modes;
override with idebus=xx
[ 4.942083] VP_IDE: IDE controller (0x1106:0x0571 rev 0x06) at PCI
slot 0000:00:11.1
[ 4.942131] VP_IDE: not 100% native mode: will probe irqs later
[ 4.942164] VP_IDE: VIA vt8231 (rev 10) IDE UDMA100 controller on
pci0000:00:11.1
[ 4.942180] ide0: BM-DMA at 0x1100-0x1107
[ 4.942194] ide1: BM-DMA at 0x1108-0x110f
[ 4.942202] Probing IDE interface ide0...
[ 4.985194] Floppy drive(s): fd0 is 1.44M
[ 5.007052] FDC 0 is a post-1991 82077
[ 5.352345] ieee1394: Host added: ID:BUS[0-00:1023] GUID[00000e10000447fc]
[ 5.356297] hda: IC25N020ATCS04-0, ATA DISK drive
[ 6.028154] hda: host max PIO5 wanted PIO255(auto-tune) selected PIO4
[ 6.028394] hda: UDMA/100 mode selected
[ 6.028606] Probing IDE interface ide1...
[ 6.892227] hdc: QSI CD-ROM SCR-242, ATAPI CD/DVD-ROM drive
[ 7.228115] hdc: host max PIO5 wanted PIO255(auto-tune) selected PIO4
[ 7.228180] hdc: UDMA/33 mode selected
[ 7.228279] ide0 at 0x1f0-0x1f7,0x3f6 on irq 14
[ 7.250440] ide1 at 0x170-0x177,0x376 on irq 15
[ 7.330537] hda: max request size: 128KiB
[ 7.333103] hda: 39070080 sectors (20003 MB) w/1768KiB Cache, CHS=38760/16/63
[ 7.333118] hda: cache flushes not supported
[ 7.333238] hda: hda1 hda2
[ 7.349595] hdc: ATAPI 24X CD-ROM drive, 128kB Cache
[ 7.349611] Uniform CD-ROM driver Revision: 3.20
[ 7.543901] device-mapper: uevent: version 1.0.3
[ 7.546320] device-mapper: ioctl: 4.13.0-ioctl (2007-10-18)
initialised: dm-devel@redhat.com
[ 7.965105] PM: Starting manual resume from disk
[ 8.064125] kjournald starting. Commit interval 5 seconds
[ 8.064164] EXT3-fs: mounted filesystem with ordered data mode.
[ 10.493947] udevd version 125 started
[ 12.850192] Linux agpgart interface v0.103
[ 12.905920] agpgart: Detected VIA ProSavage PM133/PL133/PN133 chipset
[ 12.909936] agpgart: AGP aperture is 64M @ 0xa0000000
[ 12.994082] Yenta: CardBus bridge found at 0000:00:0a.0 [10cf:10e7]
[ 12.994107] Yenta O2: res at 0x94/0xD4: ea/00
[ 12.994111] Yenta O2: enabling read prefetch/write burst
[ 13.012611] pci_hotplug: PCI Hot Plug PCI Core version: 0.5
[ 13.121001] Yenta: ISA IRQ mask 0x0820, PCI irq 9
[ 13.121011] Socket status: 30000006
[ 13.121675] Yenta: CardBus bridge found at 0000:00:0a.1 [10cf:10e7]
[ 13.170771] parport_pc: VIA 686A/8231 detected
[ 13.170780] parport_pc: probing current configuration
[ 13.170799] parport_pc: Current parallel port base: 0x378
[ 13.170878] parport0: PC-style at 0x378 (0x778), irq 7 [PCSPP,TRISTATE]
[ 13.248892] Yenta: ISA IRQ mask 0x0820, PCI irq 9
[ 13.248900] Socket status: 30000006
[ 13.253379] shpchp: Standard Hot Plug PCI Controller Driver version: 0.4
[ 13.269193] parport_pc: VIA parallel port: io=0x378, irq=7
[ 13.646627] NET: Registered protocol family 23
[ 13.771146] vt8231 0000:00:11.4: base address not set - upgrade
BIOS or use force_addr=0xaddr
[ 14.031558] input: Power Button (FF) as /class/input/input1
[ 14.056281] ACPI: Power Button (FF) [PWRF]
[ 14.056447] input: Lid Switch as /class/input/input2
[ 14.077370] ACPI: Lid Switch [LID]
[ 14.077538] input: Power Button (CM) as /class/input/input3
[ 14.104685] ACPI: Power Button (CM) [PBTN]
[ 14.141943] ACPI: AC Adapter [ADP0] (on-line)
[ 14.365111] ACPI: Battery Slot [BAT0] (battery present)
[ 14.921999] input: Video Bus as /class/input/input4
[ 14.964516] ACPI: Video Device [VGA0] (multi-head: yes rom: no post: no)
[ 16.746751] input: PC Speaker as /class/input/input5
[ 18.246172] Synaptics Touchpad, model: 1, fw: 5.9, id: 0x1b4cb1,
caps: 0x88479b/0x0
[ 18.246186] serio: Synaptics pass-through port at isa0060/serio4/input0
[ 18.315842] input: SynPS/2 Synaptics TouchPad as /class/input/input6
[ 18.525571] cs: IO port probe 0x100-0x3af: clean.
[ 18.527101] cs: IO port probe 0x3e0-0x4ff: clean.
[ 18.527742] cs: IO port probe 0x820-0x8ff: clean.
[ 18.528350] cs: IO port probe 0xc00-0xcf7: clean.
[ 18.529275] cs: IO port probe 0x100-0x3af: clean.
[ 18.530782] cs: IO port probe 0x3e0-0x4ff: clean.
[ 18.531421] cs: IO port probe 0x820-0x8ff: clean.
[ 18.531972] cs: IO port probe 0xc00-0xcf7: clean.
[ 18.532737] cs: IO port probe 0xa00-0xaff: clean.
[ 18.533432] cs: IO port probe 0xa00-0xaff: clean.
[ 19.045795] ACPI: PCI Interrupt 0000:00:11.6[C] -> Link [LNKC] ->
GSI 10 (level, low) -> IRQ 10
[ 19.796045] PCI: Setting latency timer of device 0000:00:11.6 to 64
[ 20.404101] MC'97 0 converters and GPIO not ready (0x1)
[ 20.405489] ACPI: PCI Interrupt 0000:00:11.5[C] -> Link [LNKC] ->
GSI 10 (level, low) -> IRQ 10
[ 20.405642] PCI: Setting latency timer of device 0000:00:11.5 to 64
[ 22.270093] EXT3 FS on dm-0, internal journal
[ 22.668564] loop: module loaded
[ 25.869814] kjournald starting. Commit interval 5 seconds
[ 25.870446] EXT3 FS on dm-5, internal journal
[ 25.870446] EXT3-fs: mounted filesystem with ordered data mode.
[ 25.928408] kjournald starting. Commit interval 5 seconds
[ 25.928778] EXT3 FS on dm-4, internal journal
[ 25.928778] EXT3-fs: mounted filesystem with ordered data mode.
[ 25.991913] kjournald starting. Commit interval 5 seconds
[ 25.992523] EXT3 FS on dm-1, internal journal
[ 25.992523] EXT3-fs: mounted filesystem with ordered data mode.
[ 26.049939] kjournald starting. Commit interval 5 seconds
[ 26.104946] EXT3 FS on dm-2, internal journal
[ 26.104961] EXT3-fs: mounted filesystem with ordered data mode.
[ 26.624319] Adding 319480k swap on /dev/mapper/bariyat-swap_1.
Priority:-1 extents:1 across:319480k
[ 30.616934] eth0: link up, 100Mbps, full-duplex, lpa 0x41E1
[ 36.115851] NET: Registered protocol family 10
[ 36.116905] lo: Disabled Privacy Extensions
[ 37.954818] lp0: using parport0 (interrupt-driven).
[ 37.990095] ppdev: user-space parallel port driver
[ 46.360030] eth0: no IPv6 routers present
[ 71.201841] Bluetooth: Core ver 2.11
[ 71.205894] NET: Registered protocol family 31
[ 71.205907] Bluetooth: HCI device and connection manager initialized
[ 71.205915] Bluetooth: HCI socket layer initialized
[ 71.374593] Bluetooth: L2CAP ver 2.9
[ 71.374605] Bluetooth: L2CAP socket layer initialized
[ 71.455766] Bluetooth: RFCOMM socket layer initialized
[ 71.455804] Bluetooth: RFCOMM TTY layer initialized
[ 71.455809] Bluetooth: RFCOMM ver 1.8
[ 78.735055] [drm] Initialized drm 1.1.0 20060810
[ 78.763663] ACPI: PCI Interrupt 0000:01:00.0[A] -> Link [LNKA] ->
GSI 9 (level, low) -> IRQ 9
[ 78.764147] [drm] Initialized savage 2.4.1 20050313 on minor 0
[ 78.765155] mtrr: base(0x92000000) is not aligned on a
size(0x5000000) boundary
[ 78.765820] agpgart: Found an AGP 2.0 compliant device at 0000:00:00.0.
[ 78.765851] agpgart: Putting AGP V2 device at 0000:00:00.0 into 0x mode
[ 78.765913] agpgart: Putting AGP V2 device at 0000:01:00.0 into 0x mode
[ 89.268085] eth0: no IPv6 routers present
[ 1799.390586] eth0: link down
[ 1806.056772] eth0: link up, 100Mbps, full-duplex, lpa 0x41E1
[ 1806.056772] ADDRCONF(NETDEV_CHANGE): eth0: link becomes ready
[ 1811.518169] eth0: link up, 100Mbps, full-duplex, lpa 0x41E1
[ 1812.840653] eth0: link down
[ 1814.654899] eth0: link up, 100Mbps, full-duplex, lpa 0x41E1
[ 1814.655063] ADDRCONF(NETDEV_CHANGE): eth0: link becomes ready
[ 1883.312032] eth0: no IPv6 routers present
[ 2072.085075] eth0: link down
[ 2073.751411] eth0: link up, 100Mbps, full-duplex, lpa 0x41E1
[ 2073.751623] ADDRCONF(NETDEV_CHANGE): eth0: link becomes ready
[ 2084.324035] eth0: no IPv6 routers present
[ 2096.279133] eth0: link up, 100Mbps, full-duplex, lpa 0x41E1
[ 2116.340042] eth0: no IPv6 routers present
[ 6863.137813] UDF-fs: No VRS found
[ 6863.175302] ISO 9660 Extensions: Microsoft Joliet Level 1
[ 6863.291234] ISOFS: changing to secondary root
[ 7655.568048] usb 1-1: new full speed USB device using uhci_hcd and address 2
[ 7655.729760] usb 1-1: configuration #1 chosen from 1 choice
[ 7655.731328] usb 1-1: New USB device found, idVendor=3538, idProduct=0054
[ 7655.731328] usb 1-1: New USB device strings: Mfr=1, Product=2, SerialNumber=3
[ 7655.731328] usb 1-1: Product: PQI USB Flash Drive
[ 7655.731328] usb 1-1: Manufacturer: PQI
[ 7655.731328] usb 1-1: SerialNumber: 00000000001C96
[ 7660.903713] Initializing USB Mass Storage driver...
[ 7660.907777] scsi0 : SCSI emulation for USB Mass Storage devices
[ 7660.908298] usbcore: registered new interface driver usb-storage
[ 7660.908311] USB Mass Storage support registered.
[ 7660.908425] usb-storage: device found at 2
[ 7660.908434] usb-storage: waiting for device to settle before scanning
[ 7665.909491] usb-storage: device scan complete
[ 7665.912299] scsi 0:0:0:0: Direct-Access Generic USB Flash Disk
0.00 PQ: 0 ANSI: 2
[ 7666.174245] Driver 'sd' needs updating - please use bus_type methods
[ 7666.182421] sd 0:0:0:0: [sda] 15794175 512-byte hardware sectors (8087 MB)
[ 7666.185422] sd 0:0:0:0: [sda] Write Protect is off
[ 7666.185438] sd 0:0:0:0: [sda] Mode Sense: 00 00 00 00
[ 7666.185444] sd 0:0:0:0: [sda] Assuming drive cache: write through
[ 7666.196602] sd 0:0:0:0: [sda] 15794175 512-byte hardware sectors (8087 MB)
[ 7666.198761] sd 0:0:0:0: [sda] Write Protect is off
[ 7666.198761] sd 0:0:0:0: [sda] Mode Sense: 00 00 00 00
[ 7666.198761] sd 0:0:0:0: [sda] Assuming drive cache: write through
[ 7666.198761] sda: sda1
[ 7666.277943] sd 0:0:0:0: [sda] Attached SCSI removable disk
[ 7682.748663] FAT: utf8 is not a recommended IO charset for FAT
filesystems, filesystem will be case sensitive!
[ 8109.313255] mtrr: base(0x92000000) is not aligned on a
size(0x5000000) boundary
[ 8109.314016] mtrr: base(0x92000000) is not aligned on a
size(0x5000000) boundary
[ 8109.314204] mtrr: base(0x92000000) is not aligned on a
size(0x5000000) boundary
[ 8109.314844] agpgart: Found an AGP 2.0 compliant device at 0000:00:00.0.
[ 8109.314880] agpgart: Putting AGP V2 device at 0000:00:00.0 into 0x mode
[ 8109.314942] agpgart: Putting AGP V2 device at 0000:01:00.0 into 0x mode
[ 8354.128958] UDF-fs: No VRS found
[ 8354.166089] ISO 9660 Extensions: Microsoft Joliet Level 1
[ 8354.179420] ISOFS: changing to secondary root
[ 8434.916849] mtrr: base(0x92000000) is not aligned on a
size(0x5000000) boundary
[ 8434.917953] mtrr: base(0x92000000) is not aligned on a
size(0x5000000) boundary
[ 8434.918275] mtrr: base(0x92000000) is not aligned on a
size(0x5000000) boundary
[ 8434.918901] agpgart: Found an AGP 2.0 compliant device at 0000:00:00.0.
[ 8434.918941] agpgart: Putting AGP V2 device at 0000:00:00.0 into 0x mode
[ 8434.919004] agpgart: Putting AGP V2 device at 0000:01:00.0 into 0x mode
[ 8556.415962] FAT: utf8 is not a recommended IO charset for FAT
filesystems, filesystem will be case sensitive!
[ 8612.819036] mtrr: base(0x92000000) is not aligned on a
size(0x5000000) boundary
[ 8612.819641] mtrr: base(0x92000000) is not aligned on a
size(0x5000000) boundary
[ 8612.819810] mtrr: base(0x92000000) is not aligned on a
size(0x5000000) boundary
[ 8612.820427] agpgart: Found an AGP 2.0 compliant device at 0000:00:00.0.
[ 8612.820459] agpgart: Putting AGP V2 device at 0000:00:00.0 into 0x mode
[ 8612.820521] agpgart: Putting AGP V2 device at 0000:01:00.0 into 0x mode
[ 9301.408094] usb 1-1: USB disconnect, address 2
[ 9382.880048] usb 1-1: new full speed USB device using uhci_hcd and address 3
[ 9383.041966] usb 1-1: configuration #1 chosen from 1 choice
[ 9383.044395] scsi1 : SCSI emulation for USB Mass Storage devices
[ 9383.045428] usb 1-1: New USB device found, idVendor=3538, idProduct=0054
[ 9383.045441] usb 1-1: New USB device strings: Mfr=1, Product=2, SerialNumber=3
[ 9383.045448] usb 1-1: Product: PQI USB Flash Drive
[ 9383.045452] usb 1-1: Manufacturer: PQI
[ 9383.045456] usb 1-1: SerialNumber: 00000000001C96
[ 9383.046490] usb-storage: device found at 3
[ 9383.046499] usb-storage: waiting for device to settle before scanning
[ 9388.045340] usb-storage: device scan complete
[ 9388.048170] scsi 1:0:0:0: Direct-Access Generic USB Flash Disk
0.00 PQ: 0 ANSI: 2
[ 9388.093270] sd 1:0:0:0: [sda] 15794175 512-byte hardware sectors (8087 MB)
[ 9388.096274] sd 1:0:0:0: [sda] Write Protect is off
[ 9388.096289] sd 1:0:0:0: [sda] Mode Sense: 00 00 00 00
[ 9388.096295] sd 1:0:0:0: [sda] Assuming drive cache: write through
[ 9388.108252] sd 1:0:0:0: [sda] 15794175 512-byte hardware sectors (8087 MB)
[ 9388.111261] sd 1:0:0:0: [sda] Write Protect is off
[ 9388.111277] sd 1:0:0:0: [sda] Mode Sense: 00 00 00 00
[ 9388.111283] sd 1:0:0:0: [sda] Assuming drive cache: write through
[ 9388.111309] sda: sda1
[ 9388.189002] sd 1:0:0:0: [sda] Attached SCSI removable disk
[ 9673.448708] FAT: utf8 is not a recommended IO charset for FAT
filesystems, filesystem will be case sensitive!
[ 9726.451661] usb 1-1: USB disconnect, address 3
[ 9726.452593] scsi 1:0:0:0: rejecting I/O to dead device
[ 9726.452617] scsi 1:0:0:0: rejecting I/O to dead device
[ 9726.452631] scsi 1:0:0:0: rejecting I/O to dead device
[ 9726.452641] scsi 1:0:0:0: [sda] READ CAPACITY failed
[ 9726.452646] scsi 1:0:0:0: [sda] Result: hostbyte=DID_NO_CONNECT
driverbyte=DRIVER_OK,SUGGEST_OK
[ 9726.452655] scsi 1:0:0:0: [sda] Sense not available.
[ 9726.452667] scsi 1:0:0:0: rejecting I/O to dead device
[ 9726.452678] scsi 1:0:0:0: [sda] Write Protect is off
[ 9726.452684] scsi 1:0:0:0: [sda] Mode Sense: 00 00 00 00
[ 9726.452689] scsi 1:0:0:0: [sda] Assuming drive cache: write through
[ 9726.452708] scsi 1:0:0:0: rejecting I/O to dead device
[ 9726.452721] scsi 1:0:0:0: rejecting I/O to dead device
[ 9726.452735] scsi 1:0:0:0: rejecting I/O to dead device
[ 9726.452749] scsi 1:0:0:0: rejecting I/O to dead device
[ 9726.452758] scsi 1:0:0:0: [sda] READ CAPACITY failed
[ 9726.452763] scsi 1:0:0:0: [sda] Result: hostbyte=DID_NO_CONNECT
driverbyte=DRIVER_OK,SUGGEST_OK
[ 9726.452770] scsi 1:0:0:0: [sda] Sense not available.
[ 9726.452780] scsi 1:0:0:0: rejecting I/O to dead device
[ 9726.452790] scsi 1:0:0:0: [sda] Write Protect is off
[ 9726.452795] scsi 1:0:0:0: [sda] Mode Sense: 00 00 00 00
[ 9726.452800] scsi 1:0:0:0: [sda] Assuming drive cache: write through
[ 9739.712055] usb 1-1: new full speed USB device using uhci_hcd and address 4
[ 9739.873177] usb 1-1: configuration #1 chosen from 1 choice
[ 9739.879342] scsi2 : SCSI emulation for USB Mass Storage devices
[ 9739.888627] usb 1-1: New USB device found, idVendor=3538, idProduct=0054
[ 9739.888644] usb 1-1: New USB device strings: Mfr=1, Product=2, SerialNumber=3
[ 9739.888650] usb 1-1: Product: PQI USB Flash Drive
[ 9739.888655] usb 1-1: Manufacturer: PQI
[ 9739.888659] usb 1-1: SerialNumber: 00000000001C96
[ 9739.889769] usb-storage: device found at 4
[ 9739.889782] usb-storage: waiting for device to settle before scanning
[ 9744.889381] usb-storage: device scan complete
[ 9744.893348] scsi 2:0:0:0: Direct-Access Generic USB Flash Disk
0.00 PQ: 0 ANSI: 2
[ 9744.941265] sd 2:0:0:0: [sda] 15794175 512-byte hardware sectors (8087 MB)
[ 9744.944278] sd 2:0:0:0: [sda] Write Protect is off
[ 9744.944293] sd 2:0:0:0: [sda] Mode Sense: 00 00 00 00
[ 9744.944351] sd 2:0:0:0: [sda] Assuming drive cache: write through
[ 9744.956296] sd 2:0:0:0: [sda] 15794175 512-byte hardware sectors (8087 MB)
[ 9744.959263] sd 2:0:0:0: [sda] Write Protect is off
[ 9744.959280] sd 2:0:0:0: [sda] Mode Sense: 00 00 00 00
[ 9744.959286] sd 2:0:0:0: [sda] Assuming drive cache: write through
[ 9744.959312] sda: sda1
[ 9745.038287] sd 2:0:0:0: [sda] Attached SCSI removable disk
[ 9759.514883] FAT: utf8 is not a recommended IO charset for FAT
filesystems, filesystem will be case sensitive!
[10262.904076] usb 1-1: USB disconnect, address 4
[13913.669088] mtrr: base(0x92000000) is not aligned on a
size(0x5000000) boundary
[13913.669875] mtrr: base(0x92000000) is not aligned on a
size(0x5000000) boundary
[13913.670069] mtrr: base(0x92000000) is not aligned on a
size(0x5000000) boundary
[13913.670712] agpgart: Found an AGP 2.0 compliant device at 0000:00:00.0.
[13913.670747] agpgart: Putting AGP V2 device at 0000:00:00.0 into 0x mode
[13913.670810] agpgart: Putting AGP V2 device at 0000:01:00.0 into 0x mode
[14512.896146] mtrr: base(0x92000000) is not aligned on a
size(0x5000000) boundary
[14512.897018] mtrr: base(0x92000000) is not aligned on a
size(0x5000000) boundary
[14512.897302] mtrr: base(0x92000000) is not aligned on a
size(0x5000000) boundary
[14512.897939] agpgart: Found an AGP 2.0 compliant device at 0000:00:00.0.
[14512.897980] agpgart: Putting AGP V2 device at 0000:00:00.0 into 0x mode
[14512.898043] agpgart: Putting AGP V2 device at 0000:01:00.0 into 0x mode
[14777.896115] mtrr: base(0x92000000) is not aligned on a
size(0x5000000) boundary
[14777.896979] mtrr: base(0x92000000) is not aligned on a
size(0x5000000) boundary
[14777.897258] mtrr: base(0x92000000) is not aligned on a
size(0x5000000) boundary
[14777.897912] agpgart: Found an AGP 2.0 compliant device at 0000:00:00.0.
[14777.897956] agpgart: Putting AGP V2 device at 0000:00:00.0 into 0x mode
[14777.898018] agpgart: Putting AGP V2 device at 0000:01:00.0 into 0x mode
[15414.211048] mtrr: base(0x92000000) is not aligned on a
size(0x5000000) boundary
[15414.211747] mtrr: base(0x92000000) is not aligned on a
size(0x5000000) boundary
[15414.212005] mtrr: base(0x92000000) is not aligned on a
size(0x5000000) boundary
[15414.212700] agpgart: Found an AGP 2.0 compliant device at 0000:00:00.0.
[15414.212741] agpgart: Putting AGP V2 device at 0000:00:00.0 into 0x mode
[15414.212803] agpgart: Putting AGP V2 device at 0000:01:00.0 into 0x mode
[15898.929448] dumpcap uses obsolete (PF_INET,SOCK_PACKET)
[16079.944694] UDF-fs: No VRS found
[16079.965885] ISO 9660 Extensions: Microsoft Joliet Level 3
[16079.982194] ISOFS: changing to secondary root
P.S. Учитывая, что у меня ноут, вряд ли я смогу проверить, как что-то
там внутри физически соединено
18.03.09, Andrey Nikitin<andrey.d.nikitin@gmail.com> написал(а):
> В сообщении от 18 марта 2009 James Brown написал(a):
>> Когда вставляешь диск в CD-привод, работаешь с диском, система виснет на
>> неск. минут,
>
> Смотреть dmesg на предмет проблемных сообщений от ядра.
> Наблюдал подобное у себя, когда плохо (слабо) воткнул
> IDE кабель на разъём привода.
>
> --
> С Уважением,
> Андрей Никитин
>
>
> --
> To UNSUBSCRIBE, email to debian-russian-REQUEST@lists.debian.org
> with a subject of "unsubscribe". Trouble? Contact
> listmaster@lists.debian.org
>
>
Reply to: