eth0: card reports no RX buffers.
Здравствуйте, имеем
Linux version 2.2.17 (root@fw_wp) (gcc version 2.95.2 20000220 (Debian
GNU/Linux)) #2 Thu Sep 13 18:49:06 EEST 2001
Detected 551261 kHz processor.
Console: colour VGA+ 80x25
Calibrating delay loop... 1097.73 BogoMIPS
Memory: 63312k/65472k available (836k kernel code, 416k reserved, 868k data,
40k init)
Dentry hash table entries: 8192 (order 4, 64k)
Buffer cache hash table entries: 65536 (order 6, 256k)
Page cache hash table entries: 16384 (order 4, 64k)
CPU serial number disabled.
CPU: Intel Pentium III (Coppermine) stepping 03
Checking 386/387 coupling... OK, FPU using exception 16 error reporting.
Checking 'hlt' instruction... OK.
POSIX conformance testing by UNIFIX
PCI: PCI BIOS revision 2.10 entry at 0xfb400
PCI: Using configuration type 1
PCI: Probing PCI hardware
PCI: 00:38 [1106/0596]: Work around ISA DMA hangs (00)
Activating ISA DMA hang workarounds.
Linux NET4.0 for Linux 2.2
Based upon Swansea University Computer Society NET3.039
NET4: Unix domain sockets 1.0 for Linux NET4.0.
NET4: Linux TCP/IP 1.0 for NET4.0
IP Protocols: ICMP, UDP, TCP
TCP: Hash tables configured (ehash 65536 bhash 65536)
IPv4 over IPv4 tunneling driver
early initialization of device tunl0 is deferred
GRE over IPv4 tunneling driver
early initialization of device gre0 is deferred
Initializing RT netlink socket
Starting kswapd v 1.5
Detected PS/2 Mouse Port.
Serial driver version 4.27 with no serial options enabled
ttyS00 at 0x03f8 (irq = 4) is a 16550A
ttyS01 at 0x02f8 (irq = 3) is a 16550A
pty: 256 Unix98 ptys configured
apm: BIOS version 1.2 Flags 0x07 (Driver version 1.13)
loop: registered device at major 7
VP_IDE: IDE controller on PCI bus 00 dev 39
VP_IDE: not 100% native mode: will probe irqs later
ide0: BM-DMA at 0xe000-0xe007, BIOS settings: hda:DMA, hdb:DMA
ide0: VIA Bus-Master (U)DMA Timing Config Success
ide1: BM-DMA at 0xe008-0xe00f, BIOS settings: hdc:pio, hdd:pio
ide1: VIA Bus-Master (U)DMA Timing Config Success
hda: Maxtor 91021U2, ATA DISK drive
hdb: ATAPI CD-ROM DRIVE 40X MAXIMUM, ATAPI CDROM drive
ide0 at 0x1f0-0x1f7,0x3f6 on irq 14
hda: Maxtor 91021U2, 9770MB w/512kB Cache, CHS=1245/255/63
hdb: ATAPI 40X CD-ROM drive, 128kB Cache
Uniform CD-ROM driver Revision: 3.11
Floppy drive(s): fd0 is 1.44M
FDC 0 is a post-1991 82077
eepro100.c:v1.09j-t 9/29/99 Donald Becker
http://cesdis.gsfc.nasa.gov/linux/drivers/eepro100.html
eepro100.c: $Revision: 1.20.2.10 $ 2000/05/31 Modified by Andrey V.
Savochkin <saw@saw.sw.com.sg> and others
eth0: Intel PCI EtherExpress Pro100 82557, 00:02:B3:2E:EA:31, IRQ 5.
Receiver lock-up bug exists -- enabling work-around.
Board assembly 751767-003, Physical connectors present: RJ45
Primary interface chip i82555 PHY #1.
Secondary interface chip i82555.
General self-test: passed.
Serial sub-system self-test: passed.
Internal registers self-test: passed.
ROM checksum self-test: passed (0x3258698e).
eth1: Intel PCI EtherExpress Pro100 82557, 00:02:B3:2E:DC:45, IRQ 7.
Receiver lock-up bug exists -- enabling work-around.
Board assembly 751767-003, Physical connectors present: RJ45
Primary interface chip i82555 PHY #1.
Secondary interface chip i82555.
General self-test: passed.
Serial sub-system self-test: passed.
Internal registers self-test: passed.
ROM checksum self-test: passed (0x3258698e).
eepro100.c:v1.09j-t 9/29/99 Donald Becker
http://cesdis.gsfc.nasa.gov/linux/drivers/eepro100.html
eepro100.c: $Revision: 1.20.2.10 $ 2000/05/31 Modified by Andrey V.
Savochkin <saw@saw.sw.com.sg> and others
Partition check:
hda: hda1 hda2 < hda5 > hda3
VFS: Mounted root (ext2 filesystem) readonly.
Freeing unused kernel memory: 40k freed
Adding Swap: 232932k swap-space (priority -1)
eth0: card reports no RX buffers.
eth0: card reports no resources.
eth0: card reports no RX buffers.
eth0: card reports no resources.
eth0: card reports no RX buffers.
eth0: card reports no resources.
eth0: card reports no RX buffers.
eth0: card reports no resources.
eth0: card reports no RX buffers.
eth0: card reports no resources.
И так до бесконечности , иногда помагает ifup eth0 ; ifdown eth0
Вопрос - Как отучить?
Reply to: