--- Begin Message ---
Package: installation-reports
Boot method: netboot
Image version: http://ftp.nl.debian.org/debian/dists/squeeze/main/installer-armel/current/images/iop32x/network-console/glantank/
Date: 12 Feb 2011
Machine: I/O Data GLAN TANK
Processor:
Memory:
Partitions:
knoppix@microknoppix:~$ fdisk /dev/hda
255 heads, 63 sectors/track, 30401 cylinders
Units=cylinders of 16065 * 512 = 8425280 bytes
disk identifier:0x00000000
Device Boot Start End Blocks Id System
/dev/hda1 1 32 257008+ 83 Linux
/dev/hda2 33 64 257040 82 Linux swap/Solaris
/dev/hda3 65 30401 243681952+ FD Linux raid autodetect
Output of lspci -nn and lspci -vnn:
Base System Installation Checklist:
[O] = OK, [E] = Error (please elaborate below), [ ] = didn't try it
Initial boot: [O]
Detect network card: [O]
Configure network: [O]
Detect CD: [ ]
Load installer modules: [O]
Detect hard drives: [E]
Partition hard drives: [ ]
Install base system: [ ]
Clock/timezone setup: [ ]
User/password setup: [O]
Install tasks: [ ]
Install boot loader: [ ]
Overall install: [ ]
Comments/Problems:
Why? Does not seem hard disks to detect
what do I do?
+
RedBoot(tm) bootstrap and debug environment [ROM]
Red Hat certified release, version 1.90 - built 13:59:48, Jun 3 2005
Platform: IQ80321 (XScale)
Copyright (C) 2000, 2001, 2002, Red Hat, Inc.
RAM: 0x00000000-0x08000000, 0x00010ba8-0x07ff4000 available
== Executing boot script in 1.000 seconds - enter ^C to abort
RedBoot> load hda1:/initrd -r -v -b 0x00800000 -m disk
|
Raw file loaded 0x00800000-0x00bcb0d8, assumed entry at 0x00800000
RedBoot> load hda1:/zImage -r -v -b 0x00012000 -m disk
\
Raw file loaded 0x00012000-0x001446a7, assumed entry at 0x00012000
RedBoot> exec -c "root=/dev/hda2 initrd=0xa0800000,8M rw console=ttyS0,115200 mem=128M@0xa0000000"
Using base address 0x00012000 and length 0x001326a8
Uncompressing Linux... done, booting the kernel.
[ 0.000000] Initializing cgroup subsys cpuset
[ 0.000000] Initializing cgroup subsys cpu
[ 0.000000] Linux version 2.6.32-5-iop32x (Debian 2.6.32-29) (ben@decadent.org.uk) (gcc version 4.3.5 (Debian 4.3.5-4) ) #1 Fri Dec 10 19:47:27 UTC 2010
[ 0.000000] CPU: XScale-80219 [69052e20] revision 0 (ARMv5TE), cr=0000397f
[ 0.000000] CPU: VIVT data cache, VIVT instruction cache
[ 0.000000] Machine: GLAN Tank
[ 0.000000] Memory policy: ECC disabled, Data cache writeback
[ 0.000000] Built 1 zonelists in Zone order, mobility grouping on. Total pages: 32512
[ 0.000000] Kernel command line: root=/dev/hda2 initrd=0xa0800000,8M rw console=ttyS0,115200 mem=128M@0xa0000000
[ 0.000000] PID hash table entries: 512 (order: -1, 2048 bytes)
[ 0.000000] Dentry cache hash table entries: 16384 (order: 4, 65536 bytes)
[ 0.000000] Inode-cache hash table entries: 8192 (order: 3, 32768 bytes)
[ 0.000000] Memory: 128MB = 128MB total
[ 0.000000] Memory: 117844KB available (3080K code, 444K data, 112K init, 0K highmem)
[ 0.000000] SLUB: Genslabs=11, HWalign=32, Order=0-3, MinObjects=0, CPUs=1, Nodes=1
[ 0.000000] Hierarchical RCU implementation.
[ 0.000000] NR_IRQS:32
[ 0.000000] Console: colour dummy device 80x30
[ 0.000000] Calibrating delay loop... 398.95 BogoMIPS (lpj=1994752)
[ 0.210000] Security Framework initialized
[ 0.210000] SELinux: Disabled at boot.
[ 0.210000] Mount-cache hash table entries: 512
[ 0.210000] Initializing cgroup subsys ns
[ 0.210000] Initializing cgroup subsys cpuacct
[ 0.210000] Initializing cgroup subsys devices
[ 0.210000] Initializing cgroup subsys freezer
[ 0.210000] Initializing cgroup subsys net_cls
[ 0.210000] CPU: Testing write buffer coherency: ok
[ 0.210000] devtmpfs: initialized
[ 0.210000] regulator: core version 0.5
[ 0.210000] NET: Registered protocol family 16
[ 0.220000] pci 0000:00:01.0: PME# supported from D0 D3hot D3cold
[ 0.220000] pci 0000:00:01.0: PME# disabled
[ 0.220000] pci 0000:00:03.0: PME# supported from D0 D1 D2 D3hot
[ 0.220000] pci 0000:00:03.0: PME# disabled
[ 0.220000] pci 0000:00:03.1: PME# supported from D0 D1 D2 D3hot
[ 0.220000] pci 0000:00:03.1: PME# disabled
[ 0.220000] pci 0000:00:03.2: PME# supported from D0 D1 D2 D3hot
[ 0.220000] pci 0000:00:03.2: PME# disabled
[ 0.220000] PCI: bus0: Fast back to back transfers disabled
[ 0.220000] bio: create slab <bio-0> at 0
[ 0.220000] vgaarb: loaded
[ 0.240000] NET: Registered protocol family 2
[ 0.240000] IP route cache hash table entries: 1024 (order: 0, 4096 bytes)
[ 0.240000] TCP established hash table entries: 4096 (order: 3, 32768 bytes)
[ 0.240000] TCP bind hash table entries: 4096 (order: 2, 16384 bytes)
[ 0.240000] TCP: Hash tables configured (established 4096 bind 4096)
[ 0.240000] TCP reno registered
[ 0.240000] NET: Registered protocol family 1
[ 0.240000] Unpacking initramfs...
[ 1.770000] Freeing initrd memory: 8192K
[ 1.770000] NetWinder Floating Point Emulator V0.97 (double precision)
[ 1.780000] audit: initializing netlink socket (disabled)
[ 1.780000] type=2000 audit(1.780:1): initialized
[ 1.790000] VFS: Disk quotas dquot_6.5.2
[ 1.800000] Dquot-cache hash table entries: 1024 (order 0, 4096 bytes)
[ 1.800000] msgmni has been set to 246
[ 1.800000] alg: No test for stdrng (krng)
[ 1.800000] Block layer SCSI generic (bsg) driver version 0.4 loaded (major 253)
[ 1.800000] io scheduler noop registered
[ 1.800000] io scheduler anticipatory registered
[ 1.800000] io scheduler deadline registered
[ 1.800000] io scheduler cfq registered (default)
[ 1.810000] Serial: 8250/16550 driver, 2 ports, IRQ sharing disabled
[ 1.820000] serial8250.0: ttyS0 at MMIO 0xfe800000 (irq = 30) is a 16550A
[ 2.160000] console [ttyS0] enabled
[ 2.160000] physmap platform flash device: 00080000 at f0000000
[ 2.180000] Found: ST M29W400DB
[ 2.180000] physmap-flash.0: Found 1 x16 devices at 0x0 in 16-bit bank
[ 2.210000] Support for command set 0002 not present
[ 2.210000] gen_probe: No supported Vendor Command Set found
[ 2.260000] physmap-flash physmap-flash.0: map_probe failed
[ 2.260000] mice: PS/2 mouse device common for all mice
[ 2.280000] i2c /dev entries driver
[ 2.280000] rtc-rs5c372 0-0032: rs5c372a found, 24hr, driver version 0.6
[ 2.280000] rtc-rs5c372 0-0032: rtc core: registered rtc-rs5c372 as rtc0
[ 2.650000] iop-adma iop-adma.0: Intel(R) IOP: ( cpy intr )
[ 2.670000] iop-adma iop-adma.1: Intel(R) IOP: ( cpy intr )
[ 2.670000] TCP cubic registered
[ 2.680000] NET: Registered protocol family 17
[ 2.680000] XScale DSP coprocessor detected.
[ 2.690000] registered taskstats version 1
[ 2.690000] rtc-rs5c372 0-0032: setting system clock to 2011-02-14 20:01:02 UTC (1297713662)
[ 2.710000] Initalizing network drop monitor service
[ 2.710000] Freeing init memory: 112K
[ 3.870000] Intel(R) PRO/1000 Network Driver - version 7.3.21-k5-NAPI
[ 3.880000] Copyright (c) 1999-2006 Intel Corporation.
[ 3.880000] PCI: enabling device 0000:00:01.0 (0140 -> 0143)
[ 4.040000] usbcore: registered new interface driver usbfs
[ 4.050000] usbcore: registered new interface driver hub
[ 4.050000] usbcore: registered new device driver usb
[ 4.280000] e1000: 0000:00:01.0: e1000_probe: (PCI:33MHz:32-bit) 00:a0:b0:75:e9:32
[ 4.340000] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
[ 4.550000] e1000: eth0: e1000_probe: Intel(R) PRO/1000 Network Connection
[ 4.560000] PCI: enabling device 0000:00:03.2 (0140 -> 0142)
[ 4.560000] ehci_hcd 0000:00:03.2: EHCI Host Controller
[ 4.600000] ehci_hcd 0000:00:03.2: new USB bus registered, assigned bus number 1
[ 4.600000] ehci_hcd 0000:00:03.2: Enabling legacy PCI PM
[ 4.650000] ehci_hcd 0000:00:03.2: irq 29, io mem 0x80053000
[ 4.670000] ehci_hcd 0000:00:03.2: USB 2.0 started, EHCI 1.00
[ 4.670000] usb usb1: New USB device found, idVendor=1d6b, idProduct=0002
[ 4.690000] usb usb1: New USB device strings: Mfr=3, Product=2, SerialNumber=1
[ 4.690000] usb usb1: Product: EHCI Host Controller
[ 4.690000] usb usb1: Manufacturer: Linux 2.6.32-5-iop32x ehci_hcd
[ 4.700000] usb usb1: SerialNumber: 0000:00:03.2
[ 4.780000] usb usb1: configuration #1 chosen from 1 choice
[ 4.790000] hub 1-0:1.0: USB hub found
[ 4.790000] hub 1-0:1.0: 5 ports detected
[ 4.890000] ohci_hcd: USB 1.1 'Open' Host Controller (OHCI) Driver
[ 4.890000] PCI: enabling device 0000:00:03.0 (0140 -> 0142)
[ 4.920000] ohci_hcd 0000:00:03.0: OHCI Host Controller
[ 4.920000] ohci_hcd 0000:00:03.0: new USB bus registered, assigned bus number 2
[ 4.940000] ohci_hcd 0000:00:03.0: irq 29, io mem 0x80051000
[ 5.030000] usb usb2: New USB device found, idVendor=1d6b, idProduct=0001
[ 5.030000] usb usb2: New USB device strings: Mfr=3, Product=2, SerialNumber=1
[ 5.050000] usb usb2: Product: OHCI Host Controller
[ 5.050000] usb usb2: Manufacturer: Linux 2.6.32-5-iop32x ohci_hcd
[ 5.050000] usb usb2: SerialNumber: 0000:00:03.0
[ 5.070000] usb usb2: configuration #1 chosen from 1 choice
[ 5.070000] hub 2-0:1.0: USB hub found
[ 5.070000] hub 2-0:1.0: 3 ports detected
[ 5.080000] PCI: enabling device 0000:00:03.1 (0140 -> 0142)
[ 5.080000] ohci_hcd 0000:00:03.1: OHCI Host Controller
[ 5.090000] ohci_hcd 0000:00:03.1: new USB bus registered, assigned bus number 3
[ 5.100000] ohci_hcd 0000:00:03.1: irq 29, io mem 0x80052000
[ 5.190000] usb usb3: New USB device found, idVendor=1d6b, idProduct=0001
[ 5.190000] usb usb3: New USB device strings: Mfr=3, Product=2, SerialNumber=1
[ 5.210000] usb usb3: Product: OHCI Host Controller
[ 5.210000] usb usb3: Manufacturer: Linux 2.6.32-5-iop32x ohci_hcd
[ 5.210000] usb usb3: SerialNumber: 0000:00:03.1
[ 5.220000] usb usb3: configuration #1 chosen from 1 choice
[ 5.230000] hub 3-0:1.0: USB hub found
[ 5.230000] hub 3-0:1.0: 2 ports detected
Starting system log daemon: syslogd, klogd.
.
.
.
.
.
.
.
lqqqqqqqqqqqqqqqqqqqqqqqqqqu [!] Detect disks tqqqqqqqqqqqqqqqqqqqqqqqqqqqk
x x
x No disk drive was detected. If you know the name of the driver needed x
x by your disk drive, you can select it from the list. x
x x
x Driver needed for your disk drive: x
x x
x continue with no disk drive x
x ide-cd_mod x
x ide-core x
x loop x
x scsi_dh x
x scsi_mod x
x sd_mod x
x sr_mod x
x none of the above x
x x
x <Go Back> x
x x
mqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqj
<Tab> moves; <Space> selects; <Enter> activates buttons
--- End Message ---