Re: Woody installation on IBM 44P-170 - really close
German,
Actually, it is a very good question. It took me a while to figure out.
However, you may not have seen the problem I am describing below.
I set up an RS/6000 43P-150 running SuSE 7.3 as my BOOTP/tftp server:
elas27:~ # cat /etc/bootptab
elas23:\
ht=ethernet:\
ha=000629040055:\
bf=zImage.initrd.chrp-rs6k:\
ip=9.3.52.88:\
sm=255.255.255.224:\
bs=auto
elas27:~ # ls -l /tftpboot
-rwxr-xr-x 1 rolfb users 2689856 May 13 13:29
zImage.initrd.chrp-rs6k
So why does this work? Should it not be:
bf=/tftpboot/zImage.initrd.chrp-rs6k:\
Well, unlike other BOOTP server that I have used before, this one had
/tftpboot hardcoded as root. Therefore, while I was investigating what I
thought was an Open Firmware problem, I was really trying to boot from:
/tftpboot/tftpboot/zImage.initrd.chrp-rs6k
Then all you have to do on the target machine is to issue the following
command from Open Firmware (console optional):
0> boot net console=ttyS0
I created the install boot/root image as follows:
$ mv root.bin ramdisk.image.gz
$ mv ramdisk.image.gz /usr/src/linux/arch/ppc/boot/images
$ make zImage.initrd
Rolf
--
Rolf Brudeseth
rolfb@us.ibm.com
pSeries System Engineering & Integration, IBM Enterprise Systems Group
Austin, TX, Phone: 512-838-6558
German Poo Caaman~o <gpoo@ubiobio.cl> on 05/15/2002 03:47:54 PM
To: Rolf Brudeseth/Austin/IBM@IBMUS
cc:
Subject: Re: Woody installation on IBM 44P-170 - really close
El mié, 15-05-2002 a las 12:53, Rolf Brudeseth escribió:
>
> On Tue, May 14, 2002 at 01:41:54PM -0500, Rolf Brudeseth wrote:
> >> I believe I am really close to getting Debian working on an IBM
44P-170
> >> workstation.
> >>
> >> I made a combined boot/root image. The kernel is 2.4.18 from
kernel.org,
> >> while the root image is from Debian. I used the default power3 config
> file
> >> (power3_defconfig).
> >>
> >> Root image:
> >>
>
http://ftp.debian.org/debian/dists/woody/main/disks-powerpc/current/chrp/root.bin
>
> No, I actually used:
>
http://ftp.debian.org/debian/dists/woody/main/disks-powerpc/current/chrp/images-1.44/root.bin
>
> >>
> >> 02-Apr-2002
> >>
> >> I download the boot/root image from Open Firmware via BOOTP. It starts
> up
> >> the installation routine. I am able to successfully partition/format
the
> >> hard drive.
Excuse me if my question is stupid, but, how did you boot your
machine?
Thanks in advance,
--
German Poo Caaman~o
mailto:gpoo@ubiobio.cl
http://www.ubiobio.cl/~gpoo/chilelindo.html
--
To UNSUBSCRIBE, email to debian-powerpc-request@lists.debian.org
with a subject of "unsubscribe". Trouble? Contact listmaster@lists.debian.org
Reply to: