Re: 2.6 for DECstation, d-i
* Karel van Houten <Karel@vhouten.xs4all.nl> [2006-05-11 17:45]:
> * You don't seem to have included the DEC serial drivers and console
> support for the /260, because after the prom-io I loose all output
> on the serial line (my /260 has serial console only).
Zilog Z8530 support for DECstation hasn't been ported to 2.6 yet.
> * When I let it boot without console, it will happily go multiuser.
> See boot messages below.
> * My second SCSI card does not seem to work as it should. Works OK
> under 2.4.27.
Maciej, do you have any idea?
kernel log:
> Linux version 2.6.16-1-sb1-bcm91250a (Debian 2.6.16-12)
> (waldi@debian.org) (gcc version 4.0.3 20051201 (prerelease) (Debian
> 4.0.2-5)) #2 Tue May 9 21:11:55 UTC 2006
> This is a DECstation 5000/2x0
> CPU revision is: 00000440
> FPU revision is: 00000500
> Determined physical RAM map:
> memory: 10000000 @ 00000000 (usable)
> On node 0 totalpages: 65536
> DMA zone: 65536 pages, LIFO batch:15
> DMA32 zone: 0 pages, LIFO batch:0
> Normal zone: 0 pages, LIFO batch:0
> HighMem zone: 0 pages, LIFO batch:0
> Built 1 zonelists
> Kernel command line: root=/dev/sda1 console=ttyS2
> Primary instruction cache 16kB, physically tagged, direct mapped,
> linesize 16 bytes.
> Primary data cache 16kB, direct mapped, linesize 16 bytes.
> Unified secondary cache 1024kB direct mapped, linesize 32 bytes.
> Synthesized TLB refill handler (21 instructions).
> Synthesized TLB load handler fastpath (33 instructions).
> Synthesized TLB store handler fastpath (33 instructions).
> Synthesized TLB modify handler fastpath (32 instructions).
> PID hash table entries: 2048 (order: 11, 32768 bytes)
> Using 59.999 MHz high precision timer.
> Dentry cache hash table entries: 65536 (order: 6, 262144 bytes)
> Inode-cache hash table entries: 32768 (order: 5, 131072 bytes)
> Memory: 256224k/262144k available (2270k kernel code, 5716k reserved,
> 414k data, 136k init, 0k highmem)
> Calibrating delay loop... 59.86 BogoMIPS (lpj=233472)
> Security Framework v1.0.0 initialized
> SELinux: Disabled at boot.
> Capability LSM initialized
> Mount-cache hash table entries: 512
> Checking for 'wait' instruction... unavailable.
> NET: Registered protocol family 16
> SCSI subsystem initialized
> TURBOchannel rev. 1 at 25.0 MHz (without parity)
> slot 1: DEC PMAZ-AA V5.3d
> audit: initializing netlink socket (disabled)
> audit(1147360779.414:1): initialized
> VFS: Disk quotas dquot_6.5.1
> Dquot-cache hash table entries: 1024 (order 0, 4096 bytes)
> Initializing Cryptographic API
> io scheduler noop registered (default)
> io scheduler anticipatory registered
> io scheduler deadline registered
> io scheduler cfq registered
> rtc: I/O port 530579456 is not free.
> RAMDISK driver initialized: 16 RAM disks of 8192K size 1024 blocksize
> declance.c: v0.009 by Linux MIPS DECstation task force
> declance0: IOASIC onboard LANCE, addr = 08:00:2b:37:63:76, irq = 16
> declance0: registered as eth0.
> SCSI ID 7 Clk 25MHz CCF=5 TOut 167 NCR53C9x(esp236)
> SCSI ID 7 Clk 25MHz CCF=5 TOut 167 NCR53C9x(esp236)
> ESP: Total of 2 ESP hosts found, 2 actually in use.
> scsi0 : ESP236 (NCR53C9x)
> esp0: hoping for msgout
> Vendor: COMPAQ Model: ST34371N Rev: 0388
> Type: Direct-Access ANSI SCSI revision: 02
> scsi1 : ESP236 (NCR53C9x)
> esp1: hoping for msgout
> Vendor: COMPAQ Model: ST34371N Rev: 0682
> Type: Direct-Access ANSI SCSI revision: 02
> esp1: hoping for msgout
> Vendor: COMPAQ Model: ST34371N Rev: 0388
> Type: Direct-Access ANSI SCSI revision: 02
> esp1: hoping for msgout
> Vendor: COMPAQ Model: ST34371N Rev: 0388
> Type: Direct-Access ANSI SCSI revision: 02
> esp1: hoping for msgout
> Vendor: COMPAQ Model: ST34371N Rev: 0388
> Type: Direct-Access ANSI SCSI revision: 02
> esp1: hoping for msgout
> Vendor: COMPAQ Model: ST34371N Rev: 0682
> Type: Direct-Access ANSI SCSI revision: 02
> Vendor: SONY Model: CD-ROM CDU-55S Rev: 1.0t
> Type: CD-ROM ANSI SCSI revision: 02
> SCSI device sda: 8386000 512-byte hdwr sectors (4294 MB)
> sda: Write Protect is off
> sda: Mode Sense: c7 00 10 08
> SCSI device sda: drive cache: write through w/ FUA
> SCSI device sda: 8386000 512-byte hdwr sectors (4294 MB)
> sda: Write Protect is off
> sda: Mode Sense: c7 00 10 08
> SCSI device sda: drive cache: write through w/ FUA
> sda: sda1 sda2 < sda5 >
> sd 0:0:0:0: Attached scsi disk sda
> esp1: Warning, live target 0 not responding to selection.
> esp1: Resetting scsi bus
> esp1: SCSI bus reset interrupt
> esp1: SCSI bus reset interrupt
> esp1: hoping for msgout
> sd 1:0:0:0: scsi: Device offlined - not ready after error recovery
> sd 1:0:0:0: rejecting I/O to offline device
> sd 1:0:0:0: rejecting I/O to offline device
> sd 1:0:0:0: rejecting I/O to offline device
> sd 1:0:0:0: rejecting I/O to offline device
> sdb : READ CAPACITY failed.
> sdb : status=0, message=00, host=1, driver=00
> sdb : sense not available.
> sd 1:0:0:0: rejecting I/O to offline device
> sdb: Write Protect is off
> sdb: Mode Sense: 00 00 00 00
> sd 1:0:0:0: rejecting I/O to offline device
> sdb: asking for cache data failed
> sdb: assuming drive cache: write through
> sd 1:0:0:0: Attached scsi disk sdb
> esp1: hoping for msgout
> esp1: Warning, live target 1 not responding to selection.
> esp1: Resetting scsi bus
> esp1: SCSI bus reset interrupt
> esp1: SCSI bus reset interrupt
> esp1: hoping for msgout
> sd 1:0:1:0: scsi: Device offlined - not ready after error recovery
> sd 1:0:1:0: rejecting I/O to offline device
> sd 1:0:1:0: rejecting I/O to offline device
> sd 1:0:1:0: rejecting I/O to offline device
> sd 1:0:1:0: rejecting I/O to offline device
> sdc : READ CAPACITY failed.
> sdc : status=0, message=00, host=1, driver=00
> sdc : sense not available.
> sd 1:0:1:0: rejecting I/O to offline device
> sdc: Write Protect is off
> sdc: Mode Sense: 00 00 00 00
> sd 1:0:1:0: rejecting I/O to offline device
> sdc: asking for cache data failed
> sdc: assuming drive cache: write through
> sd 1:0:1:0: Attached scsi disk sdc
> esp1: hoping for msgout
> esp1: Warning, live target 2 not responding to selection.
> esp1: Resetting scsi bus
> esp1: SCSI bus reset interrupt
> esp1: SCSI bus reset interrupt
> esp1: hoping for msgout
> sd 1:0:2:0: scsi: Device offlined - not ready after error recovery
> sd 1:0:2:0: rejecting I/O to offline device
> sd 1:0:2:0: rejecting I/O to offline device
> sd 1:0:2:0: rejecting I/O to offline device
> sd 1:0:2:0: rejecting I/O to offline device
> sdd : READ CAPACITY failed.
> sdd : status=0, message=00, host=1, driver=00
> sdd : sense not available.
> sd 1:0:2:0: rejecting I/O to offline device
> sdd: Write Protect is off
> sdd: Mode Sense: 00 00 00 00
> sd 1:0:2:0: rejecting I/O to offline device
> sdd: asking for cache data failed
> sdd: assuming drive cache: write through
> sd 1:0:2:0: Attached scsi disk sdd
> esp1: hoping for msgout
> esp1: Warning, live target 3 not responding to selection.
> esp1: Resetting scsi bus
> esp1: SCSI bus reset interrupt
> esp1: SCSI bus reset interrupt
> esp1: hoping for msgout
> sd 1:0:3:0: scsi: Device offlined - not ready after error recovery
> sd 1:0:3:0: rejecting I/O to offline device
> sd 1:0:3:0: rejecting I/O to offline device
> sd 1:0:3:0: rejecting I/O to offline device
> sd 1:0:3:0: rejecting I/O to offline device
> sde : READ CAPACITY failed.
> sde : status=0, message=00, host=1, driver=00
> sde : sense not available.
> sd 1:0:3:0: rejecting I/O to offline device
> sde: Write Protect is off
> sde: Mode Sense: 00 00 00 00
> sd 1:0:3:0: rejecting I/O to offline device
> sde: asking for cache data failed
> sde: assuming drive cache: write through
> sd 1:0:3:0: Attached scsi disk sde
> esp1: hoping for msgout
> esp1: Warning, live target 5 not responding to selection.
> esp1: Resetting scsi bus
> esp1: SCSI bus reset interrupt
> esp1: SCSI bus reset interrupt
> esp1: hoping for msgout
> sd 1:0:5:0: scsi: Device offlined - not ready after error recovery
> sd 1:0:5:0: rejecting I/O to offline device
> sd 1:0:5:0: rejecting I/O to offline device
> sd 1:0:5:0: rejecting I/O to offline device
> sd 1:0:5:0: rejecting I/O to offline device
> sdf : READ CAPACITY failed.
> sdf : status=0, message=00, host=1, driver=00
> sdf : sense not available.
> sd 1:0:5:0: rejecting I/O to offline device
> sdf: Write Protect is off
> sdf: Mode Sense: 00 00 00 00
> sd 1:0:5:0: rejecting I/O to offline device
> sdf: asking for cache data failed
> sdf: assuming drive cache: write through
> sd 1:0:5:0: Attached scsi disk sdf
> NET: Registered protocol family 2
> IP route cache hash table entries: 4096 (order: 2, 16384 bytes)
> TCP established hash table entries: 16384 (order: 4, 65536 bytes)
> TCP bind hash table entries: 16384 (order: 4, 65536 bytes)
> TCP: Hash tables configured (established 16384 bind 16384)
> TCP reno registered
> TCP bic registered
> NET: Registered protocol family 1
> NET: Registered protocol family 17
> kjournald starting. Commit interval 5 seconds
> EXT3-fs: mounted filesystem with ordered data mode.
> VFS: Mounted root (ext3 filesystem) readonly.
> Freeing unused PROM memory: 124k freed
> Freeing unused kernel memory: 260k freed
> Warning: unable to open an initial console.
> Adding 208804k swap on /dev/sda5. Priority:-1 extents:1 across:208804k
> EXT3 FS on sda1, internal journal
>
--
Martin Michlmayr
http://www.cyrius.com/
Reply to: