Cube2 install problems - Kernel panic VFS
Hello all,
I'm new here... I allready got some hints from the list archives for which
I would thank everybody.
I'm trying to install Debian on a Sun Cobalt Cube2 with 32Mb ram
using the howto Martin Michlmayer.
The first problen I encoutered was/is that the DHCP server doesn't
acknowledges the IP for the cobalt. In the list i found a workaround
for this:
net 192.168.1.10 255.255.255.0
nfs 192.168.1.1 /nfsroot vmlinux-2.4.27-r5k-cobalt initrd.gz
and than the execute (which I not completely understand)
execute initrd={initrd-size}@{initrd-start} console=ttyS0,{console-speed}
I used: execute initrd= filesize of initrd.gz @0 console=ttyS0,115200
After which I get the follow output and ending with a kernel panic
> execute initrd=1557955@0 console=ttyS0,115200
elf32: 00080000 - 0028313f (801fe040) (ffffffff.80000000)
elf32: 80080000 (80080000) 1549384t + 0t
elf32: 801fc000 (801fc000) 376832t + 176448t
net: interface down
CPU revision is: 000028a0
FPU revision is: 000028a0
Primary instruction cache 32kB, physically tagged, 2-way, linesize 32
bytes.
Primary data cache 32kB 2-way, linesize 32 bytes.
Linux version 2.4.26-r5k-cobalt (root@solitude.cyrius.com) (gcc version
3.3.3
(Debian 20040321)) #1 Sun May 16 20:51:23 UTC 2004
Determined physical RAM map:
memory: 00000000 @ 00000000 (usable)
memory: 01557955 @ 00000000 (reserved)
memory: 00aa86ab @ 01557955 (usable)
hm, page 00284000 reserved twice.
On node 0 totalpages: 8192
zone(0): 8192 pages.
zone(1): 0 pages.
zone(2): 0 pages.
Kernel command line: initrd=1557955@0 console=ttyS0,115200
Calibrating delay loop... 249.85 BogoMIPS
Memory: 10556k/10912k available (1513k kernel code, 356k reserved, 260k
data,
92k init, 0k highmem)
Dentry cache hash table entries: 4096 (order: 3, 32768 bytes)
Inode cache hash table entries: 2048 (order: 2, 16384 bytes)
Mount cache hash table entries: 512 (order: 0, 4096 bytes)
Buffer cache hash table entries: 1024 (order: 0, 4096 bytes)
Page-cache hash table entries: 8192 (order: 3, 32768 bytes)
Checking for 'wait' instruction... available.
POSIX conformance testing by UNIFIX
PCI: Probing PCI hardware
Cobalt Board ID: 5
Galileo ID: 17
Activating ISA DMA hang workarounds.
Linux NET4.0 for Linux 2.4
Based upon Swansea University Computer Society NET3.039
Initializing RT netlink socket
Starting kswapd
Journalled Block Device driver loaded
devfs: v1.12c (20020818) Richard Gooch (rgooch@atnf.csiro.au)
devfs: boot_options: 0x0
pty: 256 Unix98 ptys configured
Cobalt LCD Driver v2.10
Serial driver version 5.05c (2001-07-08) with MANY_PORTS SHARE_IRQ
SERIAL_PCI
enabled
?ttyS00 at 0xc800000 (irq = 7) is a ST16650V2
rtc: SRM (post-2000) epoch (2000) detected
Real Time Clock Driver v1.10f
RAMDISK driver initialized: 16 RAM disks of 8192K size 1024 blocksize
Linux Tulip driver version 0.9.15-pre12 (Aug 9, 2002)
PCI: Enabling device 00:07.0 (0041 -> 0043)
PCI: Unable to reserve mem region #2:400@12000000 for device 00:07.0
PCI: Unable to reserve mem region #2:400@12000000 for device 00:07.0
PCI: Enabling device 00:0c.0 (0005 -> 0007)
PCI: Unable to reserve mem region #2:400@12000400 for device 00:0c.0
PCI: Unable to reserve mem region #2:400@12000400 for device 00:0c.0
Uniform Multi-Platform E-IDE driver Revision: 7.00beta4-2.4
ide: Assuming 33MHz system bus speed for PIO modes; override with idebus=xx
VP_IDE: IDE controller at PCI slot 00:09.1
VP_IDE: chipset revision 6
VP_IDE: not 100% native mode: will probe irqs later
ide: Assuming 33MHz system bus speed for PIO modes; override with idebus=xx
VP_IDE: VIA vt82c586a (rev 27) IDE UDMA33 controller on pci00:09.1
ide0: BM-DMA at 0xcc00-0xcc07, BIOS settings: hda:pio, hdb:pio
ide1: BM-DMA at 0xcc08-0xcc0f, BIOS settings: hdc:pio, hdd:pio
hda: WDC WD43AA, ATA DISK drive
hdc: IRQ probe failed (0xfffffefa)
hdc: IRQ probe failed (0xfffffefa)
hdd: IRQ probe failed (0xfffffefa)
hdd: IRQ probe failed (0xfffffefa)
ide0 at 0x1f0-0x1f7,0x3f6 on irq 14
hda: attached ide-disk driver.
hda: 8421840 sectors (4312 MB) w/2048KiB Cache, CHS=8355/16/63
Partition check:
/dev/ide/host0/bus0/target0/lun0: p1 p2 p3 p4
Initializing Cryptographic API
NET4: Linux TCP/IP 1.0 for NET4.0
IP: routing cache hash table of 512 buckets, 4Kbytes
TCP: Hash tables configured (established 2048 bind 4096)
NET4: Unix domain sockets 1.0/SMP for Linux NET4.0.
Kernel panic: VFS: Unable to mount root fs on 01:00
All help is welcome,
Best regards,
Jacob Hooysma
----------------
This E-mail message, including any attached documentation, is
confidential. Should you have received this message wrongly, you are
urged to inform the sender at "disclaimer@ICT.nl" and remove the message
from your system. Any unauthorised dissemination of the information, in
whole or in part, is prohibited. E-mail messages can be subject to
change. ICT Automatisering NV and its subsidiaries cannot be held
responsible for incorrect, incomplete and/or delayed transfer of
messages and possible damage caused by this. Although ICT Automatisering
NV (including its subsidiaries) makes every effort to send messages free
of viruses by using a viruschecker, ICT Automatisering NV (or its
subsidiaries) cannot guarantee that the message and any attachments are
actually completely virus free.
Reply to: