filesystem corrupted like I've never seen
Hello,
My /home and /var filesystems just got corrupted real bad and I have
no idea why.
I leave my (Latitude D600) laptop on overnight at the office normally.
Except this monday morning I came into the office and tried to read my
mail, and kmail promptly crashed saying the Mail folder doesn't have
the right permissions or something.
I closed everything down, rebooted, and at reboot I get tons of ide
error messages
dmesg gives this
hda: dma_intr: error=0x40 { UncorrectableError }, LBAsect=10319090,
high=0, low=10319090, sector=10319017
ide: failed opcode was: unknown
end_request: I/O error, dev hda, sector 10319017
Buffer I/O error on device hda6, logical block 1306
hda: dma_intr: status=0x51 { DriveReady SeekComplete Error }
hda: dma_intr: error=0x40 { UncorrectableError }, LBAsect=10319090,
high=0, low=10319090, sector=10319021
ide: failed opcode was: unknown
end_request: I/O error, dev hda, sector 10319021
Buffer I/O error on device hda6, logical block 1307
hda: dma_intr: status=0x51 { DriveReady SeekComplete Error }
hda: dma_intr: error=0x40 { UncorrectableError }, LBAsect=10319090,
high=0, low=10319090, sector=10319025
ide: failed opcode was: unknown
end_request: I/O error, dev hda, sector 10319025
Buffer I/O error on device hda6, logical block 1308
hda: dma_intr: status=0x51 { DriveReady SeekComplete Error }
hda: dma_intr: error=0x40 { UncorrectableError }, LBAsect=10319090,
high=0, low=10319090, sector=10319029
ide: failed opcode was: unknown
end_request: I/O error, dev hda, sector 10319029
Buffer I/O error on device hda6, logical block 1309
hda: dma_intr: status=0x51 { DriveReady SeekComplete Error }
hda: dma_intr: error=0x40 { UncorrectableError }, LBAsect=10319090,
high=0, low=10319090, sector=10319033
ide: failed opcode was: unknown
end_request: I/O error, dev hda, sector 10319033
Buffer I/O error on device hda6, logical block 1310
hda: dma_intr: status=0x51 { DriveReady SeekComplete Error }
hda: dma_intr: error=0x40 { UncorrectableError }, LBAsect=10319090,
high=0, low=10319090, sector=10319037
ide: failed opcode was: unknown
end_request: I/O error, dev hda, sector 10319037
Buffer I/O error on device hda6, logical block 1311
hda: dma_intr: status=0x51 { DriveReady SeekComplete Error }
hda: dma_intr: error=0x40 { UncorrectableError }, LBAsect=10319090,
high=0, low=10319090, sector=10319041
ide: failed opcode was: unknown
end_request: I/O error, dev hda, sector 10319041
Buffer I/O error on device hda6, logical block 1312
hda: dma_intr: status=0x51 { DriveReady SeekComplete Error }
hda: dma_intr: error=0x40 { UncorrectableError }, LBAsect=10319090,
high=0, low=10319090, sector=10319045
ide: failed opcode was: unknown
end_request: I/O error, dev hda, sector 10319045
Buffer I/O error on device hda6, logical block 1313
hda: dma_intr: status=0x51 { DriveReady SeekComplete Error }
hda: dma_intr: error=0x40 { UncorrectableError }, LBAsect=10319090,
high=0, low=10319090, sector=10319049
ide: failed opcode was: unknown
end_request: I/O error, dev hda, sector 10319049
Buffer I/O error on device hda6, logical block 1314
hda: dma_intr: status=0x51 { DriveReady SeekComplete Error }
hda: dma_intr: error=0x40 { UncorrectableError }, LBAsect=10319090,
high=0, low=10319090, sector=10319053
ide: failed opcode was: unknown
end_request: I/O error, dev hda, sector 10319053
Buffer I/O error on device hda6, logical block 1315
hda: dma_intr: status=0x51 { DriveReady SeekComplete Error }
hda: dma_intr: error=0x40 { UncorrectableError }, LBAsect=10319090,
high=0, low=10319090, sector=10319057
ide: failed opcode was: unknown
end_request: I/O error, dev hda, sector 10319057
Buffer I/O error on device hda6, logical block 1316
hda: dma_intr: status=0x51 { DriveReady SeekComplete Error }
hda: dma_intr: error=0x40 { UncorrectableError }, LBAsect=10319090,
high=0, low=10319090, sector=10319061
ide: failed opcode was: unknown
end_request: I/O error, dev hda, sector 10319061
Buffer I/O error on device hda6, logical block 1317
hda: dma_intr: status=0x51 { DriveReady SeekComplete Error }
hda: dma_intr: error=0x40 { UncorrectableError }, LBAsect=10319090,
high=0, low=10319090, sector=10319065
ide: failed opcode was: unknown
end_request: I/O error, dev hda, sector 10319065
Buffer I/O error on device hda6, logical block 1318
hda: dma_intr: status=0x51 { DriveReady SeekComplete Error }
hda: dma_intr: error=0x40 { UncorrectableError }, LBAsect=10319090,
high=0, low=10319090, sector=10319069
ide: failed opcode was: unknown
end_request: I/O error, dev hda, sector 10319069
Buffer I/O error on device hda6, logical block 1319
hda: dma_intr: status=0x51 { DriveReady SeekComplete Error }
hda: dma_intr: error=0x40 { UncorrectableError }, LBAsect=10319090,
high=0, low=10319090, sector=10319073
ide: failed opcode was: unknown
end_request: I/O error, dev hda, sector 10319073
Buffer I/O error on device hda6, logical block 1320
hda: dma_intr: status=0x51 { DriveReady SeekComplete Error }
hda: dma_intr: error=0x40 { UncorrectableError }, LBAsect=10319090,
high=0, low=10319090, sector=10319077
ide: failed opcode was: unknown
end_request: I/O error, dev hda, sector 10319077
Buffer I/O error on device hda6, logical block 1321
hda: dma_intr: status=0x51 { DriveReady SeekComplete Error }
hda: dma_intr: error=0x40 { UncorrectableError }, LBAsect=10319090,
high=0, low=10319090, sector=10319081
ide: failed opcode was: unknown
end_request: I/O error, dev hda, sector 10319081
Buffer I/O error on device hda6, logical block 1322
hda: dma_intr: status=0x51 { DriveReady SeekComplete Error }
hda: dma_intr: error=0x40 { UncorrectableError }, LBAsect=10319090,
high=0, low=10319090, sector=10319085
ide: failed opcode was: unknown
end_request: I/O error, dev hda, sector 10319085
Buffer I/O error on device hda6, logical block 1323
hda: dma_intr: status=0x51 { DriveReady SeekComplete Error }
hda: dma_intr: error=0x40 { UncorrectableError }, LBAsect=10319090,
high=0, low=10319090, sector=10319089
ide: failed opcode was: unknown
end_request: I/O error, dev hda, sector 10319089
Buffer I/O error on device hda6, logical block 1324
kjournald starting. Commit interval 5 seconds
EXT3 FS on hda9, internal journal
EXT3-fs: recovery complete.
EXT3-fs: mounted filesystem with ordered data mode.
kjournald starting. Commit interval 5 seconds
EXT3 FS on hda8, internal journal
EXT3-fs: mounted filesystem with ordered data mode.
kjournald starting. Commit interval 5 seconds
EXT3 FS on hda5, internal journal
EXT3-fs: mounted filesystem with ordered data mode.
kjournald starting. Commit interval 5 seconds
EXT3 FS on hda6, internal journal
ext3_orphan_cleanup: deleting unreferenced inode 658444
ext3_orphan_cleanup: deleting unreferenced inode 89959
ext3_orphan_cleanup: deleting unreferenced inode 89949
EXT3-fs: hda6: 3 orphan inodes deleted
EXT3-fs: recovery complete.
EXT3-fs: mounted filesystem with ordered data mode.
tg3.c:v3.10 (September 14, 2004)
ACPI: PCI interrupt 0000:02:00.0[A] -> GSI 11 (level, low) -> IRQ 11
tg3: tg3_request_firmware (eth%d): Couldn't get firmware "tg3/tso_5705-1.1.0".
tg3: eth%d: Firmware "tg3/tso_5705-1.1.0" not loaded; continuing without TSO.
eth0: Tigon3 [partno(BCM95705A50) rev 3001 PHY(5705)]
(PCI:33MHz:32-bit) 10/100/1000BaseT Ethernet 00:0f:1f:c8:9c:55
eth0: RXcsums[1] LinkChgREG[1] MIirq[1] ASF[0] Split[0] WireSpeed[1] TSOcap[0]
USB Universal Host Controller Interface driver v2.2
ACPI: PCI interrupt 0000:00:1d.0[A] -> GSI 11 (level, low) -> IRQ 11
uhci_hcd 0000:00:1d.0: Intel Corp. 82801DB/DBL/DBM
(ICH4/ICH4-L/ICH4-M) USB UHCI Controller #1
PCI: Setting latency timer of device 0000:00:1d.0 to 64
uhci_hcd 0000:00:1d.0: irq 11, io base 0000bf80
uhci_hcd 0000:00:1d.0: new USB bus registered, assigned bus number 2
hub 2-0:1.0: USB hub found
hub 2-0:1.0: 2 ports detected
ACPI: PCI interrupt 0000:00:1d.1[B] -> GSI 11 (level, low) -> IRQ 11
uhci_hcd 0000:00:1d.1: Intel Corp. 82801DB/DBL/DBM
(ICH4/ICH4-L/ICH4-M) USB UHCI Controller #2
PCI: Setting latency timer of device 0000:00:1d.1 to 64
uhci_hcd 0000:00:1d.1: irq 11, io base 0000bf40
uhci_hcd 0000:00:1d.1: new USB bus registered, assigned bus number 3
hub 3-0:1.0: USB hub found
hub 3-0:1.0: 2 ports detected
ACPI: PCI interrupt 0000:00:1d.2[C] -> GSI 11 (level, low) -> IRQ 11
uhci_hcd 0000:00:1d.2: Intel Corp. 82801DB/DBL/DBM
(ICH4/ICH4-L/ICH4-M) USB UHCI Controller #3
PCI: Setting latency timer of device 0000:00:1d.2 to 64
uhci_hcd 0000:00:1d.2: irq 11, io base 0000bf20
uhci_hcd 0000:00:1d.2: new USB bus registered, assigned bus number 4
hub 4-0:1.0: USB hub found
hub 4-0:1.0: 2 ports detected
usb 3-1: new low speed USB device using address 2
input: Logitech USB Mouse on usb-0000:00:1d.1-1
usbcore: registered new driver hiddev
usbcore: registered new driver usbhid
drivers/usb/input/hid-core.c: v2.0:USB HID core driver
mice: PS/2 mouse device common for all mice
ts: Compaq touchscreen protocol output
input: PS/2 Generic Mouse on isa0060/serio1
input: PC Speaker
Real Time Clock Driver v1.12
parport: PnPBIOS parport detected.
parport0: PC-style at 0x378 (0x778), irq 7, dma 1
[PCSPP,TRISTATE,COMPAT,ECP,DMA]
parport0: irq 7 in use, resorting to polled operation
Linux agpgart interface v0.100 (c) Dave Jones
agpgart: Detected an Intel 855PM Chipset.
agpgart: Maximum main memory to use for agp memory: 941M
agpgart: AGP aperture is 128M @ 0xe0000000
cpci_hotplug: CompactPCI Hot Plug Core version: 0.2
pci_hotplug: PCI Hot Plug PCI Core version: 0.5
pciehp: acpi_pciehprm:\_SB_.PCI0 evaluate _BBN fail=0x5
pciehp: acpi_pciehprm:get_device PCI ROOT HID fail=0x5
shpchp: acpi_shpchprm:\_SB_.PCI0 evaluate _BBN fail=0x5
shpchp: acpi_shpchprm:get_device PCI ROOT HID fail=0x5
hw_random: cannot enable RNG, aborting
pciehp: acpi_pciehprm:\_SB_.PCI0 evaluate _BBN fail=0x5
pciehp: acpi_pciehprm:get_device PCI ROOT HID fail=0x5
shpchp: acpi_shpchprm:\_SB_.PCI0 evaluate _BBN fail=0x5
shpchp: acpi_shpchprm:get_device PCI ROOT HID fail=0x5
ACPI: PCI interrupt 0000:00:1f.6[B] -> GSI 7 (level, low) -> IRQ 7
PCI: Setting latency timer of device 0000:00:1f.6 to 64
MC'97 1 converters and GPIO not ready (0xff00)
Linux Kernel Card Services
options: [pci] [cardbus] [pm]
PCI: Enabling device 0000:02:01.0 (0000 -> 0002)
ACPI: PCI interrupt 0000:02:01.0[A] -> GSI 11 (level, low) -> IRQ 11
Yenta: CardBus bridge found at 0000:02:01.0 [1028:011d]
Yenta: ISA IRQ mask 0x0438, PCI irq 11
Socket status: 30000006
PCI: Enabling device 0000:02:01.1 (0000 -> 0002)
ACPI: PCI interrupt 0000:02:01.1[A] -> GSI 11 (level, low) -> IRQ 11
Yenta: CardBus bridge found at 0000:02:01.1 [1028:011d]
Yenta: ISA IRQ mask 0x0438, PCI irq 11
Socket status: 30000410
CSLIP: code copyright 1989 Regents of the University of California
PPP generic driver version 2.4.2
NET: Registered protocol family 10
Disabled Privacy Extensions on device c034e040(lo)
IPv6 over IPv4 tunneling driver
NET: Registered protocol family 17
ACPI: Battery Slot [BAT0] (battery present)
ACPI: Battery Slot [BAT1] (battery absent)
ACPI: AC Adapter [AC] (on-line)
ip_tables: (C) 2000-2002 Netfilter core team
tg3: eth0: Link is up at 10 Mbps, half duplex.
tg3: eth0: Flow control is off for TX and off for RX.
ip_conntrack version 2.1 (8189 buckets, 65512 max) - 332 bytes per conntrack
PPP BSD Compression module registered
PPP Deflate Compression module registered
cs: IO port probe 0x0100-0x04ff: excluding 0x4d0-0x4d7
cs: IO port probe 0x0800-0x08ff: clean.
cs: IO port probe 0x0c00-0x0cff: clean.
cs: IO port probe 0x0a00-0x0aff: clean.
cs: memory probe 0xa0000000-0xa0ffffff: clean.
mtrr: no more MTRRs available
mtrr: no more MTRRs available
mtrr: no more MTRRs available
eth0: no IPv6 routers present
codec_semaphore: semaphore is not ready [0x1][0x700300]
codec_write 1: semaphore is not ready for register 0x54
EXT3-fs error (device hda9): ext3_free_blocks: bit already cleared for
block 282624
Aborting journal on device hda9.
EXT3-fs error (device hda9): ext3_free_blocks: bit already cleared for
block 282625
EXT3-fs error (device hda9): ext3_free_blocks: bit already cleared for
block 282626
EXT3-fs error (device hda9): ext3_free_blocks: bit already cleared for
block 282627
EXT3-fs error (device hda9): ext3_free_blocks: bit already cleared for
block 282628
ext3_reserve_inode_write: aborting transaction: Journal has aborted in
__ext3_journal_get_write_access<2>EXT3-fs error (device hda9) in
ext3_reserve_inode_write: Journal has aborted
EXT3-fs error (device hda9) in ext3_truncate: Journal has aborted
ext3_reserve_inode_write: aborting transaction: Journal has aborted in
__ext3_journal_get_write_access<2>EXT3-fs error (device hda9) in
ext3_reserve_inode_write: Journal has aborted
EXT3-fs error (device hda9) in ext3_orphan_del: Journal has aborted
ext3_reserve_inode_write: aborting transaction: Journal has aborted in
__ext3_journal_get_write_access<2>EXT3-fs error (device hda9) in
ext3_reserve_inode_write: Journal has aborted
EXT3-fs error (device hda9) in ext3_delete_inode: Journal has aborted
ext3_abort called.
EXT3-fs error (device hda9): ext3_journal_start: Detected aborted journal
Remounting filesystem read-only
codec_semaphore: semaphore is not ready [0x1][0x700300]
codec_write 1: semaphore is not ready for register 0x54
df gives this
Sys. de fich. 1M-blocs Occupé Disponible Capacité Monté sur
/dev/hda1 250 183 55 78% /
tmpfs 506 0 506 0% /dev/shm
/dev/hda9 28939 3515 23954 13% /home
/dev/hda8 361 9 334 3% /tmp
/dev/hda5 4695 3096 1361 70% /usr
/dev/hda6 1787 753 939 45% /var
I have never seen this and I have no idea what could have happened,
cos I just left my computer on, over the weekend, and didn't touch it
or even log into it remotely or anything.
The only thing I can think of that might have triggered something like
this is software suspend 2, which I installed a couple of weeks ago,
but it seemed to be working alright...
Anyway, does anybody know what's going on and if there is any other
way to save the day without formatting my /home and /var partitions
(fortunately I have those filesystems each on their own logical
partition, so I can safely format them, without affecting any of the
rest of my system... except I gotta backup all my files, email folder,
etc, a pain in the butt).
Thanks for any pointers. Or perhaps there is another list I should
post this to...?
Alex.
Reply to: