[Date Prev][Date Next] [Thread Prev][Thread Next] [Date Index] [Thread Index]

Re: MIC's loud and Speaker screams when sound module loads. Why?

On Thursday 02 December 2004 21:52, p wrote:
> On Thu, Dec 02, 2004 at 01:11:43PM -0800, Benedek Frank wrote:
> __deletia__
> > Can you tell me, when the recompile is done, what do I do? How do I
> > insert the module late, when KDM starts? Write a little script like
> >
> > modprobe esssolo1
> >
> > ???
> //
> insmod <name of module>
> kthxbye.
> b.
> //


Now, the compile is done. The kernel works fine. :)

The module still loads at boot, even I put it in the /etc/hotplug/blacklist 
file. Now, It makes me think, that something else loads the module before 
hotplug could even get to it. Here is a piece of the dmesg of the machine. Do 
you know what would load it? I checked the /etc/modules and /etc/modules.conf 
file, but there is no mention about the solo1.


ide0 at 0x1f0-0x1f7,0x3f6 on irq 14
hda: max request size: 128KiB
hda: 39070080 sectors (20003 MB) w/2048KiB Cache, CHS=38760/16/63, UDMA(66)
 /dev/ide/host0/bus0/target0/lun0: p1 p2 p3
kjournald starting.  Commit interval 5 seconds
EXT3-fs: mounted filesystem with ordered data mode.
Adding 488336k swap on /dev/hda1.  Priority:-1 extents:1
EXT3 FS on hda2, internal journal
Real Time Clock Driver v1.12
SCSI subsystem initialized
Linux Kernel Card Services
  options:  [pci] [cardbus] [pm]
PCI: Enabling device 0000:00:03.0 (0000 -> 0002)
ACPI: PCI interrupt 0000:00:03.0[A] -> GSI 9 (level, low) -> IRQ 9
Yenta: CardBus bridge found at 0000:00:03.0 [1033:80e3]
Yenta: Enabling burst memory read transactions
Yenta: Using CSCINT to route CSC interrupts to PCI
Yenta: Routing CardBus interrupts to PCI
Yenta TI: socket 0000:00:03.0, mfunc 0x000c1702, devctl 0x46
Yenta: ISA IRQ mask 0x0cf8, PCI irq 9
Socket status: 30000010
e100: Intel(R) PRO/100 Network Driver, 3.0.18
e100: Copyright(c) 1999-2004 Intel Corporation
ACPI: PCI interrupt 0000:00:06.0[A] -> GSI 9 (level, low) -> IRQ 9
e100: eth0: e100_probe: addr 0xfc121000, irq 9, MAC addr 00:10:A4:77:2B:90
solo1: version v0.20 time 12:54:53 Dec  2 2004
ACPI: PCI interrupt 0000:00:04.0[A] -> GSI 11 (level, low) -> IRQ 11
solo1: joystick port at 0x14b1
solo1: ddma base address: 0x1480
usbcore: registered new driver usbfs
usbcore: registered new driver hub
ohci_hcd: 2004 Feb 02 USB 1.1 'Open' Host Controller (OHCI) Driver (PCI)
ohci_hcd: block sizes: ed 64 td 64
ACPI: PCI interrupt 0000:00:14.0[A] -> GSI 5 (level, low) -> IRQ 5
ohci_hcd 0000:00:14.0: ALi Corporation USB 1.1 Controller
ohci_hcd 0000:00:14.0: irq 5, pci mem c00d0000
ohci_hcd 0000:00:14.0: new USB bus registered, assigned bus number 1
hub 1-0:1.0: USB hub found
hub 1-0:1.0: 2 ports detected
input: PC Speaker
input: PS/2 Generic Mouse on isa0060/serio1
mice: PS/2 mouse device common for all mice
NET: Registered protocol family 23
ts: Compaq touchscreen protocol output
Linux agpgart interface v0.100 (c) Dave Jones
eepro100.c:v1.09j-t 9/29/99 Donald Becker 
eepro100.c: $Revision: 1.36 $ 2000/11/17 Modified by Andrey V. Savochkin 
<saw@saw.sw.com.sg> and others
NET: Registered protocol family 10
Disabled Privacy Extensions on device c02e5440(lo)
IPv6 over IPv4 tunneling driver
cs: IO port probe 0x0100-0x04ff: excluding 0x170-0x177 0x370-0x377
cs: IO port probe 0x0800-0x08ff: clean.
cs: IO port probe 0x0c00-0x0cff: clean.
cs: IO port probe 0x0a00-0x0aff: clean.
cs: memory probe 0xa0000000-0xa0ffffff: clean.
orinoco.c 0.13e (David Gibson <hermes@gibson.dropbear.id.au> and others)
orinoco_cs.c 0.13e (David Gibson <hermes@gibson.dropbear.id.au> and others)
eth1: Station identity 001f:0004:0001:0007
eth1: Looks like an Intersil firmware version 1.7.4
eth1: Ad-hoc demo mode supported
eth1: IEEE standard IBSS ad-hoc mode supported
eth1: WEP supported, 104-bit key
eth1: MAC address 00:09:5B:4B:F7:AD
eth1: Station name "Prism  I"
eth1: ready
eth1: index 0x01: Vcc 5.0, irq 3, io 0x0100-0x013f
eth1: Error -110 setting multicast list.
eth1: Error -110 setting multicast list.
eth1: New link status: Association Failed (0006)
eth1: New link status: Connected (0001)
eth1: no IPv6 routers present
spurious 8259A interrupt: IRQ7.

Reply to: