[Date Prev][Date Next] [Thread Prev][Thread Next] [Date Index] [Thread Index]

Re: wireless cards and 2.6.5 kernel



Hi Laurie,

Here are the results of ifconfig and iwconfig for my orinoco card (eth1) in 
the 2.6.5 kernel.  I'm kind of new to debian, so I may be missing something 
obvious.  The iwconfig command returns ""no wireless extensions"" (see 
below). 

ifconfig eth1
eth1      Link encap:Ethernet  HWaddr 00:E0:00:3D:11:D8
          BROADCAST MULTICAST  MTU:1500  Metric:1
          RX packets:0 errors:0 dropped:0 overruns:0 frame:0
          TX packets:0 errors:0 dropped:0 overruns:0 carrier:0
          collisions:0 txqueuelen:1000
          RX bytes:0 (0.0 b)  TX bytes:0 (0.0 b)
          Interrupt:9 Base address:0x1800

iwconfig eth1
eth1      no wireless extensions.


When I boot using the bf24 kernel my wireless card works perfectly and I get 
these results for the same two commands:

ifconfig
eth1      Link encap:Ethernet  HWaddr 00:02:2D:60:F9:E1
          inet addr:10.0.1.3  Bcast:10.0.1.255  Mask:255.255.255.0
          UP BROADCAST RUNNING MULTICAST  MTU:1500  Metric:1
          RX packets:1742 errors:0 dropped:0 overruns:0 frame:0
          TX packets:1895 errors:0 dropped:0 overruns:0 carrier:0
          collisions:0 txqueuelen:100
          RX bytes:885743 (864.9 KiB)  TX bytes:314130 (306.7 KiB)
          Interrupt:5 Base address:0x140

iwconfig eth1
eth1      IEEE 802.11-DS  ESSID:"1ecb13"  Nickname:"Folger"
          Mode:Managed  Frequency:2.412GHz  Access Point: 00:02:2D:1E:CB:13
          Bit Rate:11Mb/s   Tx-Power=15 dBm   Sensitivity:1/3
          Retry limit:4   RTS thr:off   Fragment thr:2347 B
          Encryption key:off
          Power Management:off
          Link Quality:18/92  Signal level:-68 dBm  Noise level:-86 dBm
          Rx invalid nwid:0  Rx invalid crypt:0  Rx invalid frag:0
          Tx excessive retries:0  Invalid misc:0   Missed beacon:0


Tim




On Monday 17 May 2004 10:28 pm, you wrote:
> Tim Folger wrote:
> >Hi,
> >
> >I'm running sarge on a fujitsu laptop, and use an orinoco gold card to
> > connect to the Internet and my home network. I recently installed
> >kernel-image-2.6.5-1-686, but when I boot using that kernel my wireless
> > card doesn't start, even though I've run modconf and installed (I think)
> > the required drivers. When I boot using the bf24 kernel (I'm using grub,
> > and have a choice) the card works fine.
> >
> >Thanks in advance for any suggestions.
> >
> >Tim
>
> Hi Tim
>
> I have an IBM r31 with a wireless mini-pci card running the orinico
> driver. Sarge & kernel 2.6.3 runs fine. But I have both eth0 [ a wired
> lan] and eth1 [the orinico card. If the wired card is plugged in I
> cannot communicate unless I do a "if ifconfig eth1 down".
>
> Does ifconfig recognize your card? is an address assigned?

-- 
Tim 



Reply to: