troubles with my modem ;o((
hey folks
i'm not very happy with my modem, because somehow it doesn't want to be
recognized. well, i think, the problem might be rather with myself then with
my computer, cause i don't really know what to do..
this is about all i know:
-----------
#cat /proc/pci
Bus 2, device 7, function 0:
Communication controller: PCI device 1813:4000 (Ambient Technologies
Inc) (rev 2).
Non-prefetchable 32 bit memory at 0x90300000 [0x90300fff].
I/O at 0xc000 [0xc0ff].
#scanpci
pci bus 0x2 cardnum 0x07 function 0x0000: vendor 0x1813 device 0x4000
Device unknown
CardVendor 0x16be card 0x0001 (Card unknown)
STATUS 0x0210 COMMAND 0x0003
CLASS 0x07 0x80 0x00 REVISION 0x02
BASE0 0x90300000 addr 0x90300000 MEM
BASE1 0x0000c001 addr 0x0000c000 I/O
MAX_LAT 0x00 MIN_GNT 0x00 INT_PIN 0x01 INT_LINE 0xff
#cat /proc/ioports
02f8-02ff : serial(set)
03f8-03ff : serial(set)
#cat /proc/tty/drivers
serial /dev/ham 240 1 serial
serial /dev/cua 5 64-127 serial:callout
serial /dev/ttyS 4 64-127 serial
#wvdialconf /etc/wvdial.conf
Scanning your serial ports for a modem.
ttyS0<*1>: ATQ0 V1 E1 -- failed with 2400 baud, next try: 4800 baud
ttyS0<*1>: ATQ0 V1 E1 -- failed with 4800 baud, next try: 9600 baud
ttyS0<*1>: ATQ0 V1 E1 -- failed with 9600 baud, next try: 19200 baud
ttyS0<*1>: ATQ0 V1 E1 -- failed with 19200 baud, next try: 115200 baud
ttyS0<*1>: ATQ0 V1 E1 -- and failed too at 115200, giving up.
ttyS1<*1>: ATQ0 V1 E1 -- failed with 2400 baud, next try: 4800 baud
ttyS1<*1>: ATQ0 V1 E1 -- failed with 4800 baud, next try: 9600 baud
ttyS1<*1>: ATQ0 V1 E1 -- failed with 9600 baud, next try: 19200 baud
ttyS1<*1>: ATQ0 V1 E1 -- failed with 19200 baud, next try: 115200 baud
ttyS1<*1>: ATQ0 V1 E1 -- and failed too at 115200, giving up.
Port Scan<*1>: S2 S3 ACM0 ACM1 ACM2 ACM3 ACM4 ACM5
Port Scan<*1>: ACM6 ACM7 ACM8 ACM9 ACM10 ACM11 ACM12 ACM13
Port Scan<*1>: ACM14 ACM15 USB0 USB1 USB2 USB3 USB4 USB5
Port Scan<*1>: USB6 USB7 USB8 USB9 USB10 USB11 USB12 USB13
Port Scan<*1>: USB14 USB15
Sorry, no modem was detected! Is it in use by another program?
Did you configure it properly with setserial?
Please read the FAQ at http://open.nit.ca/wvdial/
If you still have problems, send mail to wvdial-list@lists.nit.ca.
#setserial -a /dev/ham //locks the screen and everything!!! ;o(
/dev/ham, Line 0, UART: unknown
Port: 0x03f8, IRQ:4
Baud_base: 115200, close_delay: 0, divisor: 0
closing_wait: infinite
FLags: spd_normal skip_test
#on: http://yourvote.com/pci/pciread.asp?venid=0x1813
Vendor ID: 0x1813
Note: owned by Intel, previously Ambient Technologies
Device ID: 0x4000
Chip Number: MD5628D-L
Description: Modem
Notes: http//developer.intel.com/design/modems/support/drivers.htm
#uname -a
Linux Sappho 2.4.18a7 #1 Mon Jan 27 02:32:49 CET 2003 i686 unknown
#lsmod
Module Size Used by Tainted: PF
ham 8092 0 (unused)
hamcore 524096 0 [ham]
------------
i installed the driver from that intel page for MD5628D-L-B
there were only drivers for MD5628D-L-C and MD5628D-L-B and, the one for ~-C
didn't get installed in the first place, some error.
and this one, well, the modules get loaded, but wvdialconf doesn't seem to
look at the place it's supposed to look at, which i think, should be:
/dev/ham
which is:
crw-rw-r-- 1 root root 240, 1 Mar 1 16:11 /dev/ham
i already tried changing the group to dialout, but there was no difference,
the modem was still not found. and, by forcibly looking there with setserial
-a /dev/ham the screen and everyting locks..no reboot possible.. i really
don't know what to do, don't really know anything about serial ports and so
on.. would be very grateful if anybody could give me some hints or anything.
i read the linmodem and winmodem howto, and tried the serial-howto (which i
didn't quite understand) and i .. well i guess i'd be happy to get some help
;o)
cheers
gaia
what am i supposed to do with my serial port??
_________________________________________________________________
Tired of spam? Get advanced junk mail protection with MSN 8.
http://join.msn.com/?page=features/junkmail
Reply to: