Re: Cardbus Woody
On Fri, 2002-10-04 at 15:09, Victor Gvirtsman wrote:
> Did you try to use yenta_socket for PCMCIA controller instead of i82365 ?
> hint look in /etc/default/pcmcia
FWIW on my IBM A21p Thinkpad I see the same problem as Tiago with any
version of the kernel since 2.4.17 (latest I have tried is
2.4.20-pre8). I think it is maybe a card services bug (problems with
any release from 3.1.33 to 3.2.1).
Linux PCMCIA Card Services 3.2.1
kernel build: 2.4.19 unknown
options: [pci] [cardbus] [apm]
Intel ISA/PCI/CardBus PCIC probe:
PCI: Found IRQ 11 for device 00:02.0
PCI: Sharing IRQ 11 with 00:05.0
PCI: Sharing IRQ 11 with 01:00.0
PCI: Found IRQ 10 for device 00:02.1
TI 1450 rev 03 PCI-to-CardBus at slot 00:02, mem 0x50000000
host opts [0]: [ring] [serial pci & irq] [pci irq 11] [lat 64/176]
[bus 2/4]
host opts [1]: [ring] [serial pci & irq] [pci irq 10] [lat 64/176]
[bus 5/7]
PCI irq 11 test failed
ISA irqs (scanned) = none!<6> *NO* card interrupts, polling
interval = 1000 ms
cs: memory probe 0xa0000000-0xa0ffffff: clean.
hermes.c: 5 Apr 2002 David Gibson <hermes@gibson.dropbear.id.au>
orinoco.c 0.11b (David Gibson <hermes@gibson.dropbear.id.au> and others)
orinoco_cs.c 0.11b (David Gibson <hermes@gibson.dropbear.id.au> and
others)
cs: IO port probe 0x0100-0x04ff: excluding 0x4d0-0x4d7
cs: IO port probe 0x04d8-0x04ff: clean.
cs: IO port probe 0x0800-0x08ff: clean.
cs: IO port probe 0x0a00-0x0aff: clean.
cs: IO port probe 0x0c00-0x0cff: clean.
orinoco_cs: RequestIRQ: Resource in use
I don't have a 'yenta_socket' module, since I usually use the separate
pcmcia-modules package that I compile with make-kpkg when I build my
kernel.
If I compile PCMCIA directly in the kernel I do see that module.
Unfortunately I get no action when I insert a card. If I have a card
inserted when I start pcmcia then it finds it, but it doesn't work (at
least my WLAN card doesn't work, and that's kind of the most important
card to me :-).
For now I have stuck with 2.4.17, which (a) notices when I insert a card
in the socket, and (b) manages to find usable IRQs for both the socket
and the cards I insert into it.
With my 2.4.17 kernel things are much happier:
Linux PCMCIA Card Services 3.1.31
kernel build: 2.4.17 unknown
options: [pci] [cardbus] [apm]
Intel ISA/PCI/CardBus PCIC probe:
PCI: Found IRQ 11 for device 00:02.0
PCI: Sharing IRQ 11 with 00:05.0
PCI: Sharing IRQ 11 with 01:00.0
PCI: Found IRQ 10 for device 00:02.1
TI 1450 rev 03 PCI-to-CardBus at slot 00:02, mem 0x50000000
host opts [0]: [ring] [serial pci & irq] [pci irq 11] [lat 64/176]
[bus 2/4]
host opts [1]: [ring] [serial pci & irq] [pci irq 10] [lat 64/176]
[bus 5/7]
ISA irqs (scanned) = 3,4,7 PCI status changes
cs: memory probe 0xa0000000-0xa0ffffff: clean.
hermes.c: 3 Oct 2001 David Gibson <hermes@gibson.dropbear.id.au>
orinoco.c 0.08a (David Gibson <hermes@gibson.dropbear.id.au> and others)
orinoco_cs.c 0.08 (David Gibson <hermes@gibson.dropbear.id.au> and
others)
cs: IO port probe 0x0100-0x04ff: excluding 0x4d0-0x4d7
cs: IO port probe 0x04d8-0x04ff: clean.
cs: IO port probe 0x0800-0x08ff: clean.
cs: IO port probe 0x0a00-0x0aff: clean.
cs: IO port probe 0x0c00-0x0cff: clean.
eth1: ready
eth1: index 0x01: Vcc 3.3, irq 3, io 0x0100-0x013f
This is using an older version of Card Services (3.1.31 vs 3.2.1) , and
I _believe_ that this problem is what the finger can be pointed. I have
had no luck at all with more recent builds, but I have not gone so far
as to download the old 3.1.31 pcmcia source and use that with the newer
2.4.19 kernel - perhaps that should be what I do next.
I sure would love to get this working - it really bugs me when an
upgrade turns out to be a downgrade :-(
Regards,
Andrew.
> Tiago (Baiano) wrote:
> > Hello..
> >
> > I have a SureCom 428x Cardbus and i really need to use it..can
> > somebody help me with that??
> >
> > I try to load the module 8139too and it seem to works just
> > fine..but i can't bring up my interface, because it says that the resource
> > is busy....
> > Then try to load rtl8139 and it says that the card has no irq..
> >
> > and when i do lspci it says that the card has no IO either...
> >
> > Please help me on that...thanks..
> >
> > Tiago (Baiano)
> > UFSC Computação
> > http://www.inf.ufsc.br/~tiagosp
> > UIN: 104743537
> >
> >
>
>
>
> --
> To UNSUBSCRIBE, email to debian-laptop-request@lists.debian.org
> with a subject of "unsubscribe". Trouble? Contact listmaster@lists.debian.org
--
--
Andrew @ Catalyst .Net.NZ Ltd, PO Box 11-053, Manners St, Wellington
WEB: http://catalyst.net.nz/ PHYS: Level 2, 150-154 Willis St
DDI: +64(4)916-7201 MOB: +64(21)635-694 OFFICE: +64(4)499-2267
Survey for free with http://survey.net.nz/
--
Reply to: