[Date Prev][Date Next] [Thread Prev][Thread Next] [Date Index] [Thread Index]

sid + 3com vortex + 2.4.14



hi all, i've some difficult to work with a 3com vortex pcmcia.
i've a debian sid on a satellite toshiba 4300 (gcc 3.0).

default potato kernel 2.2.19pre17 works finely, this is dmesg output:

Linux version 2.2.19pre17 (herbert@arnor) (gcc version 2.7.2.3) #1 Tue Mar 13 22:37:59 EST 2001
Intel PCIC probe: 
  Toshiba ToPIC95-B rev 07 PCI-to-CardBus at slot 00:0b, mem 0x68000000
    host opts [0]: [slot 0xf0] [ccr 0x10] [cdr 0x86] [rcr 0xc000000] [pci irq 11] [lat 64/176] [bus 20/20]
    host opts [1]: [slot 0xf0] [ccr 0x20] [cdr 0x86] [rcr 0xc000000] [pci irq 11] [lat 64/176] [bus 21/21]
    ISA irqs (default) = 4,5,7,9,10,12 PCI status changes
cs: IO port probe 0x0c00-0x0cff: excluding 0xcf8-0xcff
cs: IO port probe 0x0800-0x08ff: clean.
cs: IO port probe 0x0100-0x04ff: excluding 0x378-0x37f 0x4d0-0x4d7
cs: IO port probe 0x0a00-0x0aff: clean.
cs: cb_alloc(bus 20): vendor 0x10b7, device 0x5257
3c59x.c:v0.99Q 5/16/2000 Donald Becker, becker@scyld.com
  http://www.scyld.com/network/vortex.html
cs: cb_config(bus 20)
  fn 0 bar 1: io 0x800-0x8ff
  fn 0 bar 2: mem 0x60021000-0x6002107f
  fn 0 bar 3: mem 0x60020000-0x6002007f
  fn 0 rom: mem 0x60000000-0x6001ffff
  irq 11
cs: cb_enable(bus 20)
  bridge io map 0 (flags 0x21): 0x800-0x8ff
  bridge mem map 0 (flags 0x1): 0x60000000-0x60021fff
vortex_attach(device 14:00.0)
eth0: 3Com 3CCFE575CT Tornado CardBus at 0x800,  00:01:03:79:bd:9d, IRQ 11
  product code 'GT' rev 20.0 date 11-16-00
eth0: CardBus functions mapped 60020000->c403f000.
  8K byte-wide RAM 5:3 Rx:Tx split, MII interface.
  MII transceiver found at address 0, status 7809.
  Enabling bus-master transmits and whole-frame receives.


all others kernel ( 2.2.20, 2.4.{10-14} )  causes panic. only with this
pcmcia. this is dmesg of 2.4.14 with a DLINK card, and it works.

  Toshiba ToPIC95-B rev 07 PCI-to-CardBus at slot 00:0b, mem 0x10000000
    host opts [0]: [slot 0xf0] [ccr 0x11] [cdr 0x86] [rcr 0xc000000] [pci irq 11] [lat 64/176] [bus 20/20]
    host opts [1]: [slot 0xf0] [ccr 0x21] [cdr 0x86] [rcr 0xc000000] [pci irq 11] [lat 64/176] [bus 21/21]
    ISA irqs (default) = 4,5,7,10,12 PCI status changes
cs: memory probe 0x0d0000-0x0dffff: clean.
cs: IO port probe 0x0100-0x04ff: excluding 0x378-0x37f 0x4d0-0x4d7
cs: IO port probe 0x0380-0x04cf: clean.
cs: IO port probe 0x04d8-0x04ff: clean.
cs: IO port probe 0x0800-0x08ff: clean.
cs: IO port probe 0x0a00-0x0aff: clean.
cs: IO port probe 0x0c00-0x0cff: clean.
eth0: NE2000 (DL10022 rev 30): io 0x300, irq 5, hw_addr 00:50:BA:7C:BB:0A


any suggestion? 
thanks in advance for reply.

--
raffaele messuti



Reply to: