-----BEGIN PGP SIGNED MESSAGE----- Hash: SHA1 - -----BEGIN PGP SIGNED MESSAGE----- Hash: SHA1 i asked this maybe a few days ago, but nobody did any replay so i post again, and hope that this time there are some people who may help me :-) i use kernel 2.2.19 / 2.4.3 and pcmcia-cs-3.1.25 and debian 2.2 r2 potato my first try was with 2.2.19 and after a short while all my attempts to get the pcmcia slots running succeded :) but with 2.4.3 nothing is working as i'm used to with 2.2.19 ok first i tryed with .config_2.4.3 in short i tried this: ============================= # # PCMCIA/CardBus support # # CONFIG_PCMCIA is not set CONFIG_SYSVIPC=y # CONFIG_BSD_PROCESS_ACCT is not set CONFIG_SYSCTL=y CONFIG_KCORE_ELF=y # CONFIG_KCORE_AOUT is not set CONFIG_BINFMT_AOUT=y CONFIG_BINFMT_ELF=y CONFIG_BINFMT_MISC=y CONFIG_PM=y CONFIG_APM=y # CONFIG_APM_IGNORE_USER_SUSPEND is not set # CONFIG_APM_DO_ENABLE is not set CONFIG_APM_CPU_IDLE=y # CONFIG_APM_DISPLAY_BLANK is not set # CONFIG_APM_RTC_IS_GMT is not set # CONFIG_APM_ALLOW_INTS is not set CONFIG_APM_REAL_MODE_POWER_OFF=y ================================ and then i compiled the modules as i did for 2.2.19: make clean make config make all make install ( i have included the make config in config_pcmcia_cs-3.1.25 as attachement ) then i tried to load the modules with /etc/init.d/pcmcia stop/start but i got a lot of errors the led on the networkcard lit and a peep i could notice but i didn't work later i tried the konfigurations as above ================================= # # PCMCIA/CardBus support # CONFIG_PCMCIA=m CONFIG_CARDBUS=y CONFIG_I82365=y # CONFIG_TCIC is not set CONFIG_SYSVIPC=y # CONFIG_BSD_PROCESS_ACCT is not set CONFIG_SYSCTL=y CONFIG_KCORE_ELF=y # CONFIG_KCORE_AOUT is not set CONFIG_BINFMT_AOUT=y CONFIG_BINFMT_ELF=y CONFIG_BINFMT_MISC=y CONFIG_PM=y CONFIG_APM=y # CONFIG_APM_IGNORE_USER_SUSPEND is not set # CONFIG_APM_DO_ENABLE is not set CONFIG_APM_CPU_IDLE=y # CONFIG_APM_DISPLAY_BLANK is not set # CONFIG_APM_RTC_IS_GMT is not set # CONFIG_APM_ALLOW_INTS is not set CONFIG_APM_REAL_MODE_POWER_OFF=y ======================================= i got the following results: Hint: insmod errors can be caused by incorrect module parameters, including invalid IO or IRQ parameters OR /lib/modules/2.4.3/kernel/drivers/pcmcia/ds.o: init_module: Operation not permitted /lib/modules/2.4.3/kernel/drivers/pcmcia/ds.o: insmod /lib/modules/2.4.3/kernel/drivers/pcmcia/ds.o failed /lib/modules/2.4.3/kernel/drivers/pcmcia/ds.o: insmod ds failed Hint: insmod errors can be caused by incorrect module parameters, including invalid IO or IRQ parameters ??? what shoul i do now??? the module(s) ds.o i82365.o pcnet_cs.o yenta_socket.o don't work anymore because of this faults and now i duno what to do? if someone could pass me some hints i would be very happy :)) - - -- From: Joachim Schiele [ http://www.dune2.de || Linux - my way! ] - -----BEGIN PGP SIGNATURE----- Version: GnuPG v1.0.4 (GNU/Linux) Comment: For info see http://www.gnupg.org iEYEARECAAYFAjrLhUAACgkQeGYPq/O+yeqeoACdHy6B7aVS+WcqyRpuMu/OiVEW +OMAoJlwlqK5RN5kZmkPFVczGj9w6vVh =5SUl - -----END PGP SIGNATURE----- -----BEGIN PGP SIGNATURE----- Version: GnuPG v1.0.4 (GNU/Linux) Comment: For info see http://www.gnupg.org iEYEARECAAYFAjrL+7oACgkQeGYPq/O+yerHFQCgjDr+HC2RVFuGa1EX4lPc6rDv 92AAn0AWTSSl3vqsaSJ9TDIwjpk4iEJq =3GdB -----END PGP SIGNATURE-----
-------- Linux PCMCIA Configuration Script --------
The default responses for each question are correct for most users.
Consult the PCMCIA-HOWTO for additional info about each option.
Linux source directory [/usr/src/linux-2.4.3]:
The kernel source tree is version 2.4.3.
The current kernel build date is Fri Oct 26 21:29:56 2001.
Build 'trusting' versions of card utilities (y/n) [y]: y
Include 32-bit (CardBus) card support (y/n) [y]: y
Include PnP BIOS resource checking (y/n) [y]: n
Module install directory [/lib/modules/2.4.3]:
Kernel configuration options:
Kernel-tree PCMCIA support is enabled.
Symmetric multiprocessing support is disabled.
PCI BIOS support is enabled.
Power management (APM) support is enabled.
SCSI support is disabled.
IEEE 1394 (FireWire) support is disabled.
Networking support is enabled.
Radio network interface support is disabled.
Token Ring device support is disabled.
Fast switching is disabled.
Frame Diverter is disabled.
Module version checking is enabled.
/proc filesystem support is enabled.
It looks like you have a System V init file setup.
X Windows include files found.
Forms library not installed.
If you wish to build the 'cardinfo' control panel, you need the Forms
library and the X Windows include files. See the HOWTO for details.
Configuration successful.
Attachment:
public_key.asc
Description: application/pgp-keys