Bug#1002978: GPU hangs in all variations tried
I ran 18 reboot experiments last night to try to fix the problem.
I reported the first couple of experiments in depth in previous notes.
I also found and reported an interaction between setting the kernel
command line option intel_idle.max_cstate=1 and using the Bullseye
version of the firmware-realtek package (see Bug#1003921).
I previously determined that my best experience (two weeks of uptime
with only occassional GPU hangs) happened when I set three kernel
command line options: i915.enable_dc=0 i915.disable_power_well=1
intel_idle.max_cstate=1.
I cycled through those options with the intel-microcode installed
hoping that the microcode would fix the problem. It didn't. In fact,
the microcode seems to cause the GPU to hang more quickly after a reboot
with less taxing of the video system (with the microcode I was able to
trigger a GPU hang within 30 minutes; without the microcode and the 3
kernel options above I have gone >10 hours before the first GPU hang).
So I have uninstalled the intel-microcode package to get the more stable
environment provided by just those three kernel command line options.
I also tried to tweak Bios parameters. This reboot included two changes
to the Bios: PCI Express Port Enabled (after several experiments, I
believe the system behaves the same either way) PEG Force Gen1 Enabled
(I fear that this option may make things worse and I might revert it to
test that hypothesis).
In this environment after about 12 hours of uptime, I triggered the
following GPU hang (just like in my 2 Jan 2022 20:21:36 report) by rapidly
moving through my desktops in fvwm with the keyboard equivalents that
I've defined for 'Desk 0 9' followed by 'Scroll +0 +100' followed by
'Scroll +0 -100' followed by 'Desk 0 11'. Before Buster, that workload
did not seem to trigger GPU hangs (or at least I didn't notice them).
$ sudo cat /sys/class/drm/card0/error
GPU HANG: ecode 6:2:ecdfbff0, in systemd-logind [654]
Kernel: 5.10.0-10-amd64 x86_64
Driver: 20200917
Time: 1642527258 s 850865 us
Boottime: 44963 s 143898 us
Uptime: 44956 s 329831 us
Capture: 4306133056 jiffies; 263676 ms ago
Active process (on ring bcs0): systemd-logind [654]
Reset count: 0
Suspend count: 0
Platform: SANDYBRIDGE
Subplatform: 0x0
PCI ID: 0x0102
PCI Revision: 0x09
PCI Subsystem: 1565:110d
IOMMU enabled?: 0
RPM wakelock: yes
PM suspended: no
GT awake: yes
EIR: 0x00000000
IER: 0x82bc8585
GTIER[0]: 0x00401001
PGTBL_ER: 0x00000000
FORCEWAKE: 0x00000000
DERRMR: 0x0000ffff
fence[0] = fde03b007f6001
fence[1] = 121600701117003
fence[2] = 00000000
fence[3] = 00000000
fence[4] = 00000000
fence[5] = 00000000
fence[6] = 00000000
fence[7] = 00000000
fence[8] = 00000000
fence[9] = 00000000
fence[10] = 00000000
fence[11] = 00000000
fence[12] = 00000000
fence[13] = 00000000
fence[14] = 00000000
fence[15] = 00000000
ERROR: 0x00000000
DONE_REG: 0x00000000
bcs0 command stream:
CCID: 0x00000000
START: 0x00005000
HEAD: 0x1980189c [0x00001818]
TAIL: 0x00001920 [0x00001890, 0x000018a0]
CTL: 0x00003001
MODE: 0x00000000
HWS: 0x7fffb000
ACTHD: 0x00000000 1980189c
IPEIR: 0x00000000
IPEHR: 0x13204001
ESR: 0x00000000
INSTDONE: 0xfffffff1
batch: [0x00000000_7fff3000, 0x00000000_7fff7000]
BBADDR: 0x00000000_7fff3020
BB_STATE: 0x00000000
INSTPS: 0x00000000
INSTPM: 0x00000000
FADDR: 0x00000000 00006920
RC PSMI: 0x00000010
FAULT_REG: 0x00000000
GFX_MODE: 0x00000000
PP_DIR_BASE: 0x00000000
engine reset count: 0
Active context: systemd-logind[654] prio 0, guilty 0 active 0, runtime total 0ns, avg 0ns
bcs0 --- HW Status = 0x00000000 7fffb000
:cL%-H!!!TcYFl"(R.G$,&eK-$Fk6JP!!!!^8HXBk!&t"]
bcs0 --- batch = 0x00000000 7fff3000
:RI-Mhk7i^]h4M_*f\>/Odhf1)`oBdnOpO$&,_K,;&lcn\E6_K/LS?1f+pd7lYi2iWE3I`b#YL2C/2de-Jf;]gW<id>5m_XdEi*f9K1P)56rG5:QaNrbrk)LdB:YIJZi3.4[BqDfmG>mtms]3Bb^T0(F(Xl&IA^D:\Wr@0-$?<R"abYBG5Js%C0p?+q3uTe:Z';[rQ0C\C:>e(-+)gjn?^Qtj,h(66ZV5rk0#@Z+),Nqp`"7#\As=[X4>/2#(=Qfb.)tLaE1IYQ@AlT)GJ;`&+1?&mt/lqP;99fU`Door#<7u7TIAsrWG=:Tp9U!P,/i/IDC!)i[+L'c-(/XqqHi7`67og\^fhBo;Wlci^MeKmBI<SCYN]`&T.]^Q#RB5!ZbC*b.+!l$,%EOQ#S_]2Z3*-<Q)NE0*QbN_0=]=19N"^KC;=YAR%KMe(jK$+1MSTXsBWi5N`Y7>XEpjj&o8krP2%%E=DaJkg7G:4>a$NB?qJ9>XJJ+rf<jd\=%dQ)1.1^Q#S;O"^P5mX1V,ma[qGMXsK65=hiB?.cLs-!:FtS19Mnki&TsuR9'rDWD_n\mr/ri>Y&3%DZq=r]^#_Nia2Noc>+XS`80@bl"DDDNFZ_D"ag;u\WN.s@Jg22F!E0o2=P&5`^WtHp$`mkgdY;^`4b+%"B?dK2-5C1ItICPgrd-n]uZab.Js^gI5<A4/m,<alGa5"`9m%C_WF<f&b#44%W,?Md<kTtn3Pn$7TIAin/h2@R9'rl@j;4;qqu,XS4ou>dImoN`;T0h]]qsdE<,nY+$,OL>Y%'ZLH)\Q_$>V]k#K>m6A7S6,M]M!X,0@)fI1)Xq$Ii`paGl+P:GQH_-AGsH^5)%>YMd=X(-$Y_3J,b)-7K4_8h1rN2qcTn1fo]P:GR38"VD=L%dpDiX,*oIrchaE>8<PcGYR)BAc_GN/XfokMW\ggl/:j=+eds'b%.!cEL4?i^rVSoBRVNMV<:heOc$Mdi";?=`$(u19MjbJkQJ,"O?5fAR%s%58'E&n3$.7Od0nfp]?su'.Vuc=M`KO9O@iQ<@29^F$lTT')41ilQ[n=jmWoDSjl_uYCi,Wi\IY^9j\%+XDVTSCDtNnX,),=-QL`3Dh.Q>&i-U8S)B:,Us,lq-Kr.1<Q)$/aGl2A]G7]_Urp3>q)=:[+/nd`Q#R%V"1^.KQ#S1!06#F/X:<KkO370^s):cQR#c?:3DuK9`r%RgpU.-L<8$:U>OK,)NF$)MjZ6"O*R@m_GMW\Q432S;=Y#pc/"Md4<$F-+X!c*3R9<'nmd>3JVrgMGT%VtK6e]/;ns4X83`^(]StpbOl0nlVk8/qjUHc_q0;WhAjs[lK]1Aj]Df8?i0NXXF"`eHl/an&^Fc11N1&Ldaf,0+R\S[sK;`lPbH9RoQiGRT:JN4=&LJusBLdiHsoA`jV4SV*dCRE,irJ>)0D_50qfK7s]-#&K'pUtWtDGtW.bEf+k)]=K,2N]aBHtN;J.s^Y(e]14'gJVo2g9R"DnjqKoc*=Vl=PC7OIkGXR?2i.jZ,#/U!plMumdS93FlCaR3p2nrn/h=4N2qg4pcj+io.&`TT=Mbm5Co/@`+<1A'mp:8gr5Ou$G26A.cO>'X:<>D'Re!1<Q$usrkhWGa'm3=\9mFSS%#K$bH+[FQ7^kBUrI<8f@=?cXQ_Oq%p3SJa32XH#Cd7k=rer=PhYR9G4ghZ/Nn>[(VHL"G;/:ZI/<T7Qu@3al_`M4IG5jG'7ShpPl?f[>8FXOlo\fi>X1LYF$lg9=CR->^^%G-R9("3gI7#7Cn6Sm?3i^0R'Nk=QK&rt<tLG.B;%nb!?U9'AR%hl_+.NOR9'u]P!,L1Q[t3;[#D&BS:1mUZcpS%*X$baj4jd;<Q&D*)#NGbQ#SeY4:U\'*-W5Qb.*%N^aFJ"=]Z22cPqA9$@@bBQ#SAQ"ePFMAR&"q+Y902!F+:^19MmpIQJ@Q4+P/C>X^g_gr1UOe%hhNR9+X$F2g]4*.g6j=HSkg&nf#A/m"HBY<Q6[n4`7+7TIC[n8-Xp7TIBP]FR*XSn2.l(Y?2:<tQ7a,1VMf<Q)lG0mEI`.cM*9!a;iRb.*tUK9ppU19Mn+i0EJ'N2qf9i77eM/?=VC\Ah5)LjQsRqrTH1JG/",19Mm@[?8`f-MSg6@j<J_<qm><3K#BH<phnb.cPpHGUWH1Ib\>V<Q#pI%b8Qg<Q(HtB3oWp]AT78:X#kqUI'Nc+l!I;eu:F-JI5r5kO9L4N/XfnT>9WL2_qN`n@?rl`/FCQ^%3">"CH/619MrGpb;,6k#K>Mno^)*M-'0]kDYA#,@A8ggoiK92;ru).cM'0O/=?^,2^1*6[(;g+++Dt^pi*619MeXH-spHHh\*C&ggVs\B<\(&s%V4HeB9<8:Q5Pmpp!78,+8+ej`ZX5JW?C>-b:XqQ[qbEA[S1GqkGHE?+lp,@c"a".qc_AR%L8^_a\[)-7D'!ag<-)-7HSn5VuHk#K?8(G[qW<a1-X[#D&uR4PYq[:NT/^$cF0M<BD%2meOEiYDG'AgoMcpcEom,:_[SquF*PM^m_(mPj;h&bk5>0hId7JbL>N19MoVPH>;O,TjiqKg.>qJe+RC7TIC]n8)$pbc?OiSTJqT*IJ!;4cu"L4Iu`ZUh*e+T>AS'&i-U42o$fAbZS!\h8ZF<\:qX*q29*EAo],&]`'hn0(Xe/h</dfdTu$UX_MHe6^SsW:#o[2(6nJ@qY;Gj06R9o0AUl^fWMkkC;4oN/OR,>`OL+u]oQLc3amK?ht.hZf,:WU2uCDV1&.>,P4.HbVK6Q,RNur%E>d5_9W=3E;u*O(>aF)eq'U*TPOb38^W@jO-SO9/f:#e:n4:9#4+5ASKrk<rPPHU"aZm-ar<l-q^VMLO[[X12]Dou;GKZ3?btIttq'Ri=bO0.qBjZI6qO;t@mI`?blSUboGI>>;m5UG)GC+A0Ef$6b<_jg>g6QOfm@a/a1QgR,$TYQ.Mq7'fD7OUc0lCcpOWr(d-:A4FQ><u"Drq]Zl@)K@0"Bg<lZfQIcgMWIHHE.7Ig7bVkCL"MC!W6s[jfmm[WCR@g-'jrEppO(lIP[&V[G8EX`WFS]ru.`G/iFr-Cq82D-ms(A,gsoGenOhn26N-6HFD+s,J-b$iWF`m<&C*]Og`LmKW=`C]=?`J+Yb;C;mC'a%K`e:9WE3b]^`gebemIY&@ukY9WCd:ssW!`kFCgF![m06Z[\UJ,SW/rVkb2Asj+o/GU[jmV*cZ)u`F`,k('D\2HkQ`;Qqp@3KpjR^(:jLTXGAfM,H):%:'T^BDNdX7ru_PIJ,CaSPd[q4#>\B)g*4s782K:]KuESA5)jkNB1$^,>FmEgqOmX-O`;meVu/?Jftu2sL>k2#Ua)514@=0Kf@/Y+AWDIXM1@Ijk:ic2GLSI\AtX/D&n+oeI3Z!!&h&
bcs0 --- ring = 0x00000000 00005000
:f$0_05f6L=h=8N*>_!=n*'/7&gu<?6]8?V:]=>8\pNLV(/,+$MPT.EAjU;D1h^/NBB#us$s1^AactO,1i[ME`T*CDKRR61Uh7JBSV#?i0pVrs>V#@HsGX=CUY_r):gLh!Xq7Q/ti51XnEIQL7DReqiMV:)@s#ba,iXB=T-9-btLe3ULR,SH_Zt;:P3IU[Eb]t@DORjGXnj"b;Q8jP"Lh2Sh=Q0Ko+P&N+,@,Ki#6-`>&=X`:Z,@Eu5jWJ"LCh';K@o/u%O(O*!-,pr*'tWb0ujhqE<:-uJ,Vd)S9Z7&&/Q<REPs0D6X4U7`t10LEW+rM6elYdaT1nsLEf[Va4(&L?8[61J\Io[A.V6BGp+&r+WNiP`$e+eKQ.2.&.omL&]>qb6UYntpQ.*LO!H9&*[?J#XFNk$*_8\[1.MmIE<;9@BcKI8`&^C"A8qX4&6Tu>Oi0.JjM(ElK?3UMFWp<80_.Lacm\HP?d>@d&P&f+OMr9:NZ^qV%&8VV3/8pAV>DAb'h=E"E=Gd`[2_H]`#V>Z1iX%'&<.YpdDQ\g5dYM>7hDdB%ai36*'eUc(Io%-q$k`ida@D7eOd#S*bh\&kj"')$P0=k=V&ou4HKZC+c[]MiYZ0]LF;m7^an4:!,5FK
available engines: 7
slice total: 0, mask=0000
subslice total: 0
EU total: 0
EU per subslice: 0
has slice power gating: no
has subslice power gating: no
has EU power gating: no
Unavailable
Num Pipes: 2
Pipe [0]:
Power: on
SRC: 077f0437
STAT: 00000000
Plane [0]:
CNTR: d8004400
STRIDE: 00001e00
ADDR: 00000000
SURF: 007f6000
TILEOFF: 00000000
Cursor [0]:
CNTR: 04004027
POS: 02160678
BASE: 00fdf000
Pipe [1]:
Power: on
SRC: 00000000
STAT: 00000000
Plane [1]:
CNTR: 00004000
STRIDE: 00000000
ADDR: 00000000
SURF: 00000000
TILEOFF: 00000000
Cursor [1]:
CNTR: 00000000
POS: 00000000
BASE: 00000000
CPU transcoder: A
Power: on
CONF: c0000000
HTOTAL: 0897077f
HBLANK: 0897077f
HSYNC: 080307d7
VTOTAL: 04640437
VBLANK: 04640437
VSYNC: 0440043b
CPU transcoder: B
Power: on
CONF: 00000000
HTOTAL: 00000000
HBLANK: 00000000
HSYNC: 00000000
VTOTAL: 00000000
VBLANK: 00000000
VSYNC: 00000000
gen: 6
gt: 1
iommu: disabled
memory-regions: 5
page-sizes: 1000
platform: SANDYBRIDGE
ppgtt-size: 31
ppgtt-type: 1
dma_mask_size: 40
is_mobile: no
is_lp: no
require_force_probe: no
is_dgfx: no
has_64bit_reloc: no
gpu_reset_clobbers_display: no
has_reset_engine: no
has_fpga_dbg: no
has_global_mocs: no
has_gt_uc: no
has_l3_dpf: no
has_llc: yes
has_logical_ring_contexts: no
has_logical_ring_elsq: no
has_logical_ring_preemption: no
has_master_unit_irq: no
has_pooled_eu: no
has_rc6: yes
has_rc6p: yes
has_rps: yes
has_runtime_pm: no
has_snoop: no
has_coherent_ggtt: yes
unfenced_needs_alignment: no
hws_needs_physical: no
cursor_needs_physical: no
has_csr: no
has_ddi: no
has_dp_mst: no
has_dsb: no
has_dsc: no
has_fbc: yes
has_gmch: no
has_hdcp: no
has_hotplug: yes
has_hti: no
has_ipc: no
has_modular_fia: no
has_overlay: no
has_psr: no
has_psr_hw_tracking: no
overlay_needs_physical: no
supports_tv: no
rawclk rate: 125000 kHz
CS timestamp frequency: 12500000 Hz
Has logical contexts? yes
scheduler: 0
i915.vbt_firmware=(null)
i915.modeset=-1
i915.lvds_channel_mode=0
i915.panel_use_ssc=-1
i915.vbt_sdvo_panel_type=-1
i915.enable_dc=0
i915.enable_fbc=0
i915.enable_psr=-1
i915.psr_safest_params=no
i915.enable_psr2_sel_fetch=no
i915.disable_power_well=1
i915.enable_ips=1
i915.invert_brightness=0
i915.enable_guc=0
i915.guc_log_level=-1
i915.guc_firmware_path=(null)
i915.huc_firmware_path=(null)
i915.dmc_firmware_path=(null)
i915.mmio_debug=0
i915.edp_vswing=0
i915.reset=3
i915.inject_probe_failure=0
i915.fastboot=-1
i915.enable_dpcd_backlight=-1
i915.force_probe=
i915.fake_lmem_start=0
i915.enable_hangcheck=yes
i915.load_detect_test=no
i915.force_reset_modeset_test=no
i915.error_capture=yes
i915.disable_display=no
i915.verbose_state_checks=yes
i915.nuclear_pageflip=no
i915.enable_dp_mst=yes
i915.enable_gvt=no
$ sudo dmesg
[ 0.000000] Linux version 5.10.0-10-amd64 (debian-kernel@lists.debian.org) (gcc-10 (Debian 10.2.1-6) 10.2.1 20210110, GNU ld (GNU Binutils for Debian) 2.35.2) #1 SMP Debian 5.10.84-1 (2021-12-08)
[ 0.000000] Command line: BOOT_IMAGE=/boot/vmlinuz-5.10.0-10-amd64 root=/dev/mapper/precession-root ro quiet i915.enable_dc=0 i915.disable_power_well=1 intel_idle.max_cstate=1
[ 0.000000] x86/fpu: Supporting XSAVE feature 0x001: 'x87 floating point registers'
[ 0.000000] x86/fpu: Supporting XSAVE feature 0x002: 'SSE registers'
[ 0.000000] x86/fpu: Enabled xstate features 0x3, context size is 576 bytes, using 'standard' format.
[ 0.000000] BIOS-provided physical RAM map:
[ 0.000000] BIOS-e820: [mem 0x0000000000000000-0x000000000009d7ff] usable
[ 0.000000] BIOS-e820: [mem 0x000000000009d800-0x000000000009ffff] reserved
[ 0.000000] BIOS-e820: [mem 0x00000000000e0000-0x00000000000fffff] reserved
[ 0.000000] BIOS-e820: [mem 0x0000000000100000-0x000000001fffffff] usable
[ 0.000000] BIOS-e820: [mem 0x0000000020000000-0x00000000201fffff] reserved
[ 0.000000] BIOS-e820: [mem 0x0000000020200000-0x000000003fffffff] usable
[ 0.000000] BIOS-e820: [mem 0x0000000040000000-0x00000000401fffff] reserved
[ 0.000000] BIOS-e820: [mem 0x0000000040200000-0x00000000bad92fff] usable
[ 0.000000] BIOS-e820: [mem 0x00000000bad93000-0x00000000badd9fff] ACPI NVS
[ 0.000000] BIOS-e820: [mem 0x00000000badda000-0x00000000bade0fff] ACPI data
[ 0.000000] BIOS-e820: [mem 0x00000000bade1000-0x00000000bade1fff] ACPI NVS
[ 0.000000] BIOS-e820: [mem 0x00000000bade2000-0x00000000bae04fff] reserved
[ 0.000000] BIOS-e820: [mem 0x00000000bae05000-0x00000000bae05fff] usable
[ 0.000000] BIOS-e820: [mem 0x00000000bae06000-0x00000000bae17fff] reserved
[ 0.000000] BIOS-e820: [mem 0x00000000bae18000-0x00000000bae24fff] ACPI NVS
[ 0.000000] BIOS-e820: [mem 0x00000000bae25000-0x00000000bae48fff] reserved
[ 0.000000] BIOS-e820: [mem 0x00000000bae49000-0x00000000bae8bfff] ACPI NVS
[ 0.000000] BIOS-e820: [mem 0x00000000bae8c000-0x00000000baffffff] usable
[ 0.000000] BIOS-e820: [mem 0x00000000bb800000-0x00000000bf9fffff] reserved
[ 0.000000] BIOS-e820: [mem 0x00000000fed1c000-0x00000000fed1ffff] reserved
[ 0.000000] BIOS-e820: [mem 0x00000000ff000000-0x00000000ffffffff] reserved
[ 0.000000] BIOS-e820: [mem 0x0000000100000000-0x000000023fdfffff] usable
[ 0.000000] NX (Execute Disable) protection: active
[ 0.000000] SMBIOS 2.7 present.
[ 0.000000] DMI: BIOSTAR Group H61MU3/H61MU3, BIOS 4.6.4 04/07/2011
[ 0.000000] tsc: Fast TSC calibration using PIT
[ 0.000000] tsc: Detected 2394.353 MHz processor
[ 0.000832] e820: update [mem 0x00000000-0x00000fff] usable ==> reserved
[ 0.000835] e820: remove [mem 0x000a0000-0x000fffff] usable
[ 0.000843] last_pfn = 0x23fe00 max_arch_pfn = 0x400000000
[ 0.000848] MTRR default type: uncachable
[ 0.000849] MTRR fixed ranges enabled:
[ 0.000850] 00000-9FFFF write-back
[ 0.000851] A0000-BFFFF uncachable
[ 0.000852] C0000-CFFFF write-protect
[ 0.000853] D0000-E7FFF uncachable
[ 0.000854] E8000-FFFFF write-protect
[ 0.000855] MTRR variable ranges enabled:
[ 0.000857] 0 base 000000000 mask E00000000 write-back
[ 0.000858] 1 base 200000000 mask FC0000000 write-back
[ 0.000859] 2 base 0BB800000 mask FFF800000 uncachable
[ 0.000860] 3 base 0BC000000 mask FFC000000 uncachable
[ 0.000861] 4 base 0C0000000 mask FC0000000 uncachable
[ 0.000862] 5 base 23FE00000 mask FFFE00000 uncachable
[ 0.000863] 6 disabled
[ 0.000864] 7 disabled
[ 0.000864] 8 disabled
[ 0.000865] 9 disabled
[ 0.001449] x86/PAT: Configuration [0-7]: WB WC UC- UC WB WP UC- WT
[ 0.001684] e820: update [mem 0xbb800000-0xffffffff] usable ==> reserved
[ 0.001690] last_pfn = 0xbb000 max_arch_pfn = 0x400000000
[ 0.012449] found SMP MP-table at [mem 0x000fcdd0-0x000fcddf]
[ 0.050381] reserving inaccessible SNB gfx pages
[ 0.050688] RAMDISK: [mem 0x34159000-0x360a3fff]
[ 0.050692] ACPI: Early table checksum verification disabled
[ 0.050695] ACPI: RSDP 0x00000000000F0450 000024 (v02 ALASKA)
[ 0.050700] ACPI: XSDT 0x00000000BADDA068 000054 (v01 ALASKA A M I 01072009 AMI 00010013)
[ 0.050706] ACPI: FACP 0x00000000BADE09C8 0000F4 (v04 ALASKA A M I 01072009 AMI 00010013)
[ 0.050712] ACPI: DSDT 0x00000000BADDA150 006876 (v02 ALASKA A M I 00000015 INTL 20051117)
[ 0.050716] ACPI: FACS 0x00000000BAE1CF80 000040
[ 0.050719] ACPI: APIC 0x00000000BADE0AC0 000062 (v03 ALASKA A M I 01072009 AMI 00010013)
[ 0.050722] ACPI: SSDT 0x00000000BADE0B28 000098 (v01 AMICPU PROC 00000001 MSFT 03000001)
[ 0.050726] ACPI: MCFG 0x00000000BADE0BC0 00003C (v01 ALASKA A M I 01072009 MSFT 00000097)
[ 0.050729] ACPI: HPET 0x00000000BADE0C00 000038 (v01 ALASKA A M I 01072009 AMI. 00000004)
[ 0.050733] ACPI: ASPT 0x00000000BADE0C38 000034 (v07 ALASKA PerfTune 01072009 AMI 00000000)
[ 0.050736] ACPI: Reserving FACP table memory at [mem 0xbade09c8-0xbade0abb]
[ 0.050738] ACPI: Reserving DSDT table memory at [mem 0xbadda150-0xbade09c5]
[ 0.050738] ACPI: Reserving FACS table memory at [mem 0xbae1cf80-0xbae1cfbf]
[ 0.050739] ACPI: Reserving APIC table memory at [mem 0xbade0ac0-0xbade0b21]
[ 0.050740] ACPI: Reserving SSDT table memory at [mem 0xbade0b28-0xbade0bbf]
[ 0.050741] ACPI: Reserving MCFG table memory at [mem 0xbade0bc0-0xbade0bfb]
[ 0.050743] ACPI: Reserving HPET table memory at [mem 0xbade0c00-0xbade0c37]
[ 0.050744] ACPI: Reserving ASPT table memory at [mem 0xbade0c38-0xbade0c6b]
[ 0.050754] ACPI: Local APIC address 0xfee00000
[ 0.050804] No NUMA configuration found
[ 0.050805] Faking a node at [mem 0x0000000000000000-0x000000023fdfffff]
[ 0.050817] NODE_DATA(0) allocated [mem 0x23fdd5000-0x23fdfefff]
[ 0.051299] Zone ranges:
[ 0.051300] DMA [mem 0x0000000000001000-0x0000000000ffffff]
[ 0.051301] DMA32 [mem 0x0000000001000000-0x00000000ffffffff]
[ 0.051303] Normal [mem 0x0000000100000000-0x000000023fdfffff]
[ 0.051304] Device empty
[ 0.051306] Movable zone start for each node
[ 0.051309] Early memory node ranges
[ 0.051310] node 0: [mem 0x0000000000001000-0x000000000009cfff]
[ 0.051312] node 0: [mem 0x0000000000100000-0x000000001fffffff]
[ 0.051313] node 0: [mem 0x0000000020200000-0x000000003fffffff]
[ 0.051314] node 0: [mem 0x0000000040200000-0x00000000bad92fff]
[ 0.051315] node 0: [mem 0x00000000bae05000-0x00000000bae05fff]
[ 0.051315] node 0: [mem 0x00000000bae8c000-0x00000000baffffff]
[ 0.051316] node 0: [mem 0x0000000100000000-0x000000023fdfffff]
[ 0.051319] Initmem setup node 0 [mem 0x0000000000001000-0x000000023fdfffff]
[ 0.051320] On node 0 totalpages: 2074788
[ 0.051322] DMA zone: 64 pages used for memmap
[ 0.051322] DMA zone: 156 pages reserved
[ 0.051324] DMA zone: 3996 pages, LIFO batch:0
[ 0.051325] DMA32 zone: 11885 pages used for memmap
[ 0.051326] DMA32 zone: 760584 pages, LIFO batch:63
[ 0.051327] Normal zone: 20472 pages used for memmap
[ 0.051328] Normal zone: 1310208 pages, LIFO batch:63
[ 0.051331] On node 0, zone DMA: 1 pages in unavailable ranges
[ 0.051373] On node 0, zone DMA: 99 pages in unavailable ranges
[ 0.054167] On node 0, zone DMA32: 512 pages in unavailable ranges
[ 0.059581] On node 0, zone DMA32: 512 pages in unavailable ranges
[ 0.059585] On node 0, zone DMA32: 114 pages in unavailable ranges
[ 0.059592] On node 0, zone DMA32: 134 pages in unavailable ranges
[ 0.060214] On node 0, zone Normal: 20480 pages in unavailable ranges
[ 0.060225] On node 0, zone Normal: 512 pages in unavailable ranges
[ 0.060243] Reserving Intel graphics memory at [mem 0xbba00000-0xbf9fffff]
[ 0.060555] ACPI: PM-Timer IO Port: 0x408
[ 0.060557] ACPI: Local APIC address 0xfee00000
[ 0.060564] ACPI: LAPIC_NMI (acpi_id[0xff] high edge lint[0x1])
[ 0.060575] IOAPIC[0]: apic_id 0, version 32, address 0xfec00000, GSI 0-23
[ 0.060577] ACPI: INT_SRC_OVR (bus 0 bus_irq 0 global_irq 2 dfl dfl)
[ 0.060579] ACPI: INT_SRC_OVR (bus 0 bus_irq 9 global_irq 9 high level)
[ 0.060580] ACPI: IRQ0 used by override.
[ 0.060582] ACPI: IRQ9 used by override.
[ 0.060584] Using ACPI (MADT) for SMP configuration information
[ 0.060585] ACPI: HPET id: 0x8086a701 base: 0xfed00000
[ 0.060590] TSC deadline timer available
[ 0.060592] smpboot: Allowing 2 CPUs, 0 hotplug CPUs
[ 0.060618] PM: hibernation: Registered nosave memory: [mem 0x00000000-0x00000fff]
[ 0.060620] PM: hibernation: Registered nosave memory: [mem 0x0009d000-0x0009dfff]
[ 0.060621] PM: hibernation: Registered nosave memory: [mem 0x0009e000-0x0009ffff]
[ 0.060622] PM: hibernation: Registered nosave memory: [mem 0x000a0000-0x000dffff]
[ 0.060623] PM: hibernation: Registered nosave memory: [mem 0x000e0000-0x000fffff]
[ 0.060625] PM: hibernation: Registered nosave memory: [mem 0x20000000-0x201fffff]
[ 0.060627] PM: hibernation: Registered nosave memory: [mem 0x40000000-0x401fffff]
[ 0.060628] PM: hibernation: Registered nosave memory: [mem 0xbad93000-0xbadd9fff]
[ 0.060629] PM: hibernation: Registered nosave memory: [mem 0xbadda000-0xbade0fff]
[ 0.060630] PM: hibernation: Registered nosave memory: [mem 0xbade1000-0xbade1fff]
[ 0.060631] PM: hibernation: Registered nosave memory: [mem 0xbade2000-0xbae04fff]
[ 0.060633] PM: hibernation: Registered nosave memory: [mem 0xbae06000-0xbae17fff]
[ 0.060634] PM: hibernation: Registered nosave memory: [mem 0xbae18000-0xbae24fff]
[ 0.060634] PM: hibernation: Registered nosave memory: [mem 0xbae25000-0xbae48fff]
[ 0.060635] PM: hibernation: Registered nosave memory: [mem 0xbae49000-0xbae8bfff]
[ 0.060637] PM: hibernation: Registered nosave memory: [mem 0xbb000000-0xbb7fffff]
[ 0.060638] PM: hibernation: Registered nosave memory: [mem 0xbb800000-0xbf9fffff]
[ 0.060639] PM: hibernation: Registered nosave memory: [mem 0xbfa00000-0xfed1bfff]
[ 0.060640] PM: hibernation: Registered nosave memory: [mem 0xfed1c000-0xfed1ffff]
[ 0.060640] PM: hibernation: Registered nosave memory: [mem 0xfed20000-0xfeffffff]
[ 0.060641] PM: hibernation: Registered nosave memory: [mem 0xff000000-0xffffffff]
[ 0.060643] [mem 0xbfa00000-0xfed1bfff] available for PCI devices
[ 0.060644] Booting paravirtualized kernel on bare hardware
[ 0.060648] clocksource: refined-jiffies: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 7645519600211568 ns
[ 0.065786] setup_percpu: NR_CPUS:8192 nr_cpumask_bits:2 nr_cpu_ids:2 nr_node_ids:1
[ 0.066012] percpu: Embedded 58 pages/cpu s200536 r8192 d28840 u1048576
[ 0.066022] pcpu-alloc: s200536 r8192 d28840 u1048576 alloc=1*2097152
[ 0.066024] pcpu-alloc: [0] 0 1
[ 0.066061] Built 1 zonelists, mobility grouping on. Total pages: 2042211
[ 0.066062] Policy zone: Normal
[ 0.066064] Kernel command line: BOOT_IMAGE=/boot/vmlinuz-5.10.0-10-amd64 root=/dev/mapper/precession-root ro quiet i915.enable_dc=0 i915.disable_power_well=1 intel_idle.max_cstate=1
[ 0.066704] Dentry cache hash table entries: 1048576 (order: 11, 8388608 bytes, linear)
[ 0.066987] Inode-cache hash table entries: 524288 (order: 10, 4194304 bytes, linear)
[ 0.067028] mem auto-init: stack:off, heap alloc:on, heap free:off
[ 0.084672] Memory: 3090928K/8299152K available (12295K kernel code, 2545K rwdata, 7564K rodata, 2408K init, 3684K bss, 277528K reserved, 0K cma-reserved)
[ 0.084680] random: get_random_u64 called from __kmem_cache_create+0x2a/0x4d0 with crng_init=0
[ 0.084805] SLUB: HWalign=64, Order=0-3, MinObjects=0, CPUs=2, Nodes=1
[ 0.084818] Kernel/User page tables isolation: enabled
[ 0.084835] ftrace: allocating 36444 entries in 143 pages
[ 0.098995] ftrace: allocated 143 pages with 5 groups
[ 0.099115] rcu: Hierarchical RCU implementation.
[ 0.099116] rcu: RCU restricting CPUs from NR_CPUS=8192 to nr_cpu_ids=2.
[ 0.099117] Rude variant of Tasks RCU enabled.
[ 0.099118] Tracing variant of Tasks RCU enabled.
[ 0.099119] rcu: RCU calculated value of scheduler-enlistment delay is 25 jiffies.
[ 0.099120] rcu: Adjusting geometry for rcu_fanout_leaf=16, nr_cpu_ids=2
[ 0.103622] NR_IRQS: 524544, nr_irqs: 440, preallocated irqs: 16
[ 0.105714] Console: colour VGA+ 80x25
[ 0.105728] printk: console [tty0] enabled
[ 0.105743] ACPI: Core revision 20200925
[ 0.105821] clocksource: hpet: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 133484882848 ns
[ 0.105836] APIC: Switch to symmetric I/O mode setup
[ 0.106263] ..TIMER: vector=0x30 apic1=0 pin1=2 apic2=-1 pin2=-1
[ 0.125838] clocksource: tsc-early: mask: 0xffffffffffffffff max_cycles: 0x228360c9f8c, max_idle_ns: 440795245427 ns
[ 0.125843] Calibrating delay loop (skipped), value calculated using timer frequency.. 4788.70 BogoMIPS (lpj=9577412)
[ 0.125846] pid_max: default: 32768 minimum: 301
[ 0.125871] LSM: Security Framework initializing
[ 0.125881] Yama: disabled by default; enable with sysctl kernel.yama.*
[ 0.125913] AppArmor: AppArmor initialized
[ 0.125915] TOMOYO Linux initialized
[ 0.125943] Mount-cache hash table entries: 16384 (order: 5, 131072 bytes, linear)
[ 0.125959] Mountpoint-cache hash table entries: 16384 (order: 5, 131072 bytes, linear)
[ 0.126227] mce: CPU0: Thermal monitoring enabled (TM1)
[ 0.126236] process: using mwait in idle threads
[ 0.126239] Last level iTLB entries: 4KB 512, 2MB 8, 4MB 8
[ 0.126240] Last level dTLB entries: 4KB 512, 2MB 32, 4MB 32, 1GB 0
[ 0.126243] Spectre V1 : Mitigation: usercopy/swapgs barriers and __user pointer sanitization
[ 0.126245] Spectre V2 : Mitigation: Full generic retpoline
[ 0.126246] Spectre V2 : Spectre v2 / SpectreRSB mitigation: Filling RSB on context switch
[ 0.126247] Speculative Store Bypass: Vulnerable
[ 0.126249] MDS: Vulnerable: Clear CPU buffers attempted, no microcode
[ 0.126354] Freeing SMP alternatives memory: 32K
[ 0.129937] smpboot: CPU0: Intel(R) Celeron(R) CPU G530 @ 2.40GHz (family: 0x6, model: 0x2a, stepping: 0x7)
[ 0.130094] Performance Events: PEBS fmt1+, SandyBridge events, 16-deep LBR, full-width counters, Intel PMU driver.
[ 0.130103] core: PEBS disabled due to CPU errata, please upgrade microcode
[ 0.130105] ... version: 3
[ 0.130106] ... bit width: 48
[ 0.130107] ... generic registers: 8
[ 0.130108] ... value mask: 0000ffffffffffff
[ 0.130108] ... max period: 00007fffffffffff
[ 0.130109] ... fixed-purpose events: 3
[ 0.130110] ... event mask: 00000007000000ff
[ 0.130258] rcu: Hierarchical SRCU implementation.
[ 0.130789] NMI watchdog: Enabled. Permanently consumes one hw-PMU counter.
[ 0.130841] smp: Bringing up secondary CPUs ...
[ 0.130947] x86: Booting SMP configuration:
[ 0.130949] .... node #0, CPUs: #1
[ 0.133216] smp: Brought up 1 node, 2 CPUs
[ 0.133216] smpboot: Max logical packages: 1
[ 0.133216] smpboot: Total of 2 processors activated (9577.41 BogoMIPS)
[ 0.146406] node 0 deferred pages initialised in 12ms
[ 0.146443] devtmpfs: initialized
[ 0.146443] x86/mm: Memory block size: 128MB
[ 0.146626] PM: Registering ACPI NVS region [mem 0xbad93000-0xbadd9fff] (290816 bytes)
[ 0.146626] PM: Registering ACPI NVS region [mem 0xbade1000-0xbade1fff] (4096 bytes)
[ 0.146626] PM: Registering ACPI NVS region [mem 0xbae18000-0xbae24fff] (53248 bytes)
[ 0.146626] PM: Registering ACPI NVS region [mem 0xbae49000-0xbae8bfff] (274432 bytes)
[ 0.146626] clocksource: jiffies: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 7645041785100000 ns
[ 0.146626] futex hash table entries: 512 (order: 3, 32768 bytes, linear)
[ 0.146626] pinctrl core: initialized pinctrl subsystem
[ 0.146626] NET: Registered protocol family 16
[ 0.146626] audit: initializing netlink subsys (disabled)
[ 0.146626] audit: type=2000 audit(1642482295.040:1): state=initialized audit_enabled=0 res=1
[ 0.146626] thermal_sys: Registered thermal governor 'fair_share'
[ 0.146626] thermal_sys: Registered thermal governor 'bang_bang'
[ 0.146626] thermal_sys: Registered thermal governor 'step_wise'
[ 0.146626] thermal_sys: Registered thermal governor 'user_space'
[ 0.146626] thermal_sys: Registered thermal governor 'power_allocator'
[ 0.146626] cpuidle: using governor ladder
[ 0.146626] cpuidle: using governor menu
[ 0.146626] ACPI: bus type PCI registered
[ 0.146626] acpiphp: ACPI Hot Plug PCI Controller Driver version: 0.5
[ 0.146626] PCI: MMCONFIG for domain 0000 [bus 00-ff] at [mem 0xe0000000-0xefffffff] (base 0xe0000000)
[ 0.146626] PCI: not using MMCONFIG
[ 0.146626] PCI: Using configuration type 1 for base access
[ 0.146626] core: PMU erratum BJ122, BV98, HSD29 workaround disabled, HT off
[ 0.146626] ENERGY_PERF_BIAS: Set to 'normal', was 'performance'
[ 0.150411] Kprobes globally optimized
[ 0.150416] HugeTLB registered 2.00 MiB page size, pre-allocated 0 pages
[ 0.350136] ACPI: Added _OSI(Module Device)
[ 0.350136] ACPI: Added _OSI(Processor Device)
[ 0.350136] ACPI: Added _OSI(3.0 _SCP Extensions)
[ 0.350136] ACPI: Added _OSI(Processor Aggregator Device)
[ 0.350136] ACPI: Added _OSI(Linux-Dell-Video)
[ 0.350136] ACPI: Added _OSI(Linux-Lenovo-NV-HDMI-Audio)
[ 0.350136] ACPI: Added _OSI(Linux-HPI-Hybrid-Graphics)
[ 0.355797] ACPI: 2 ACPI AML tables successfully acquired and loaded
[ 0.356621] ACPI: Dynamic OEM Table Load:
[ 0.356626] ACPI: SSDT 0xFFFF8A7D2A6E3A00 0001D8 (v01 AMI IST 00000001 MSFT 03000001)
[ 0.356943] ACPI: Dynamic OEM Table Load:
[ 0.356946] ACPI: SSDT 0xFFFF8A7C00397420 000054 (v01 AMI CST 00000001 MSFT 03000001)
[ 0.357813] ACPI: Interpreter enabled
[ 0.357827] ACPI: (supports S0 S4 S5)
[ 0.357828] ACPI: Using IOAPIC for interrupt routing
[ 0.357858] PCI: MMCONFIG for domain 0000 [bus 00-ff] at [mem 0xe0000000-0xefffffff] (base 0xe0000000)
[ 0.357922] PCI: MMCONFIG at [mem 0xe0000000-0xefffffff] reserved in ACPI motherboard resources
[ 0.357928] pmd_set_huge: Cannot satisfy [mem 0xe0000000-0xe0200000] with a huge-page mapping due to MTRR override.
[ 0.358281] PCI: Using host bridge windows from ACPI; if necessary, use "pci=nocrs" and report a bug
[ 0.358585] ACPI: Enabled 9 GPEs in block 00 to 3F
[ 0.358763] ACPI: [Firmware Bug]: BIOS _OSI(Linux) query ignored
[ 0.364038] ACPI: PCI Root Bridge [PCI0] (domain 0000 [bus 00-ff])
[ 0.364044] acpi PNP0A08:00: _OSC: OS supports [ExtendedConfig ASPM ClockPM Segments MSI HPX-Type3]
[ 0.364182] acpi PNP0A08:00: _OSC: platform does not support [SHPCHotplug LTR]
[ 0.364309] acpi PNP0A08:00: _OSC: OS now controls [PCIeHotplug PME AER PCIeCapability]
[ 0.364563] PCI host bridge to bus 0000:00
[ 0.364566] pci_bus 0000:00: root bus resource [io 0x0000-0x03af window]
[ 0.364567] pci_bus 0000:00: root bus resource [io 0x03e0-0x0cf7 window]
[ 0.364569] pci_bus 0000:00: root bus resource [io 0x03b0-0x03df window]
[ 0.364570] pci_bus 0000:00: root bus resource [io 0x0d00-0xffff window]
[ 0.364571] pci_bus 0000:00: root bus resource [mem 0x000a0000-0x000bffff window]
[ 0.364572] pci_bus 0000:00: root bus resource [mem 0x000c0000-0x000dffff window]
[ 0.364574] pci_bus 0000:00: root bus resource [mem 0xbfa00000-0xffffffff window]
[ 0.364575] pci_bus 0000:00: root bus resource [bus 00-ff]
[ 0.364588] pci 0000:00:00.0: [8086:0100] type 00 class 0x060000
[ 0.364676] pci 0000:00:01.0: [8086:0101] type 01 class 0x060400
[ 0.364715] pci 0000:00:01.0: PME# supported from D0 D3hot D3cold
[ 0.364806] pci 0000:00:02.0: [8086:0102] type 00 class 0x030000
[ 0.364815] pci 0000:00:02.0: reg 0x10: [mem 0xfe000000-0xfe3fffff 64bit]
[ 0.364820] pci 0000:00:02.0: reg 0x18: [mem 0xc0000000-0xcfffffff 64bit pref]
[ 0.364825] pci 0000:00:02.0: reg 0x20: [io 0xf000-0xf03f]
[ 0.364940] pci 0000:00:16.0: [8086:1c3a] type 00 class 0x078000
[ 0.364961] pci 0000:00:16.0: reg 0x10: [mem 0xfe608000-0xfe60800f 64bit]
[ 0.365038] pci 0000:00:16.0: PME# supported from D0 D3hot D3cold
[ 0.365126] pci 0000:00:1a.0: [8086:1c2d] type 00 class 0x0c0320
[ 0.365143] pci 0000:00:1a.0: reg 0x10: [mem 0xfe607000-0xfe6073ff]
[ 0.365231] pci 0000:00:1a.0: PME# supported from D0 D3hot D3cold
[ 0.365325] pci 0000:00:1b.0: [8086:1c20] type 00 class 0x040300
[ 0.365343] pci 0000:00:1b.0: reg 0x10: [mem 0xfe600000-0xfe603fff 64bit]
[ 0.365426] pci 0000:00:1b.0: PME# supported from D0 D3hot D3cold
[ 0.365509] pci 0000:00:1c.0: [8086:1c10] type 01 class 0x060400
[ 0.365604] pci 0000:00:1c.0: PME# supported from D0 D3hot D3cold
[ 0.365709] pci 0000:00:1c.1: [8086:1c12] type 01 class 0x060400
[ 0.365804] pci 0000:00:1c.1: PME# supported from D0 D3hot D3cold
[ 0.365914] pci 0000:00:1c.2: [8086:244e] type 01 class 0x060401
[ 0.366010] pci 0000:00:1c.2: PME# supported from D0 D3hot D3cold
[ 0.366117] pci 0000:00:1d.0: [8086:1c26] type 00 class 0x0c0320
[ 0.366135] pci 0000:00:1d.0: reg 0x10: [mem 0xfe606000-0xfe6063ff]
[ 0.366222] pci 0000:00:1d.0: PME# supported from D0 D3hot D3cold
[ 0.366315] pci 0000:00:1f.0: [8086:1c5c] type 00 class 0x060100
[ 0.366504] pci 0000:00:1f.2: [8086:1c02] type 00 class 0x010601
[ 0.366519] pci 0000:00:1f.2: reg 0x10: [io 0xf0b0-0xf0b7]
[ 0.366527] pci 0000:00:1f.2: reg 0x14: [io 0xf0a0-0xf0a3]
[ 0.366535] pci 0000:00:1f.2: reg 0x18: [io 0xf090-0xf097]
[ 0.366543] pci 0000:00:1f.2: reg 0x1c: [io 0xf080-0xf083]
[ 0.366551] pci 0000:00:1f.2: reg 0x20: [io 0xf060-0xf07f]
[ 0.366560] pci 0000:00:1f.2: reg 0x24: [mem 0xfe605000-0xfe6057ff]
[ 0.366603] pci 0000:00:1f.2: PME# supported from D3hot
[ 0.366685] pci 0000:00:1f.3: [8086:1c22] type 00 class 0x0c0500
[ 0.366704] pci 0000:00:1f.3: reg 0x10: [mem 0xfe604000-0xfe6040ff 64bit]
[ 0.366726] pci 0000:00:1f.3: reg 0x20: [io 0xf040-0xf05f]
[ 0.366839] pci 0000:00:01.0: PCI bridge to [bus 01]
[ 0.366989] pci 0000:02:00.0: [10ec:8168] type 00 class 0x020000
[ 0.367077] pci 0000:02:00.0: reg 0x10: [io 0xe000-0xe0ff]
[ 0.367197] pci 0000:02:00.0: reg 0x18: [mem 0xd0004000-0xd0004fff 64bit pref]
[ 0.367271] pci 0000:02:00.0: reg 0x20: [mem 0xd0000000-0xd0003fff 64bit pref]
[ 0.367719] pci 0000:02:00.0: supports D1 D2
[ 0.367721] pci 0000:02:00.0: PME# supported from D0 D1 D2 D3hot D3cold
[ 0.368136] pci 0000:00:1c.0: PCI bridge to [bus 02]
[ 0.368141] pci 0000:00:1c.0: bridge window [io 0xe000-0xefff]
[ 0.368149] pci 0000:00:1c.0: bridge window [mem 0xd0000000-0xd00fffff 64bit pref]
[ 0.368230] pci 0000:03:00.0: [1b21:1042] type 00 class 0x0c0330
[ 0.368274] pci 0000:03:00.0: reg 0x10: [mem 0xfe500000-0xfe507fff 64bit]
[ 0.368491] pci 0000:03:00.0: PME# supported from D3hot
[ 0.368616] pci 0000:00:1c.1: PCI bridge to [bus 03]
[ 0.368623] pci 0000:00:1c.1: bridge window [mem 0xfe500000-0xfe5fffff]
[ 0.368705] pci 0000:04:00.0: [1283:8893] type 01 class 0x060401
[ 0.368905] pci 0000:04:00.0: supports D1 D2
[ 0.368906] pci 0000:04:00.0: PME# supported from D0 D1 D2 D3hot D3cold
[ 0.368974] pci 0000:00:1c.2: PCI bridge to [bus 04-05] (subtractive decode)
[ 0.368979] pci 0000:00:1c.2: bridge window [io 0xd000-0xdfff]
[ 0.368983] pci 0000:00:1c.2: bridge window [mem 0xfe400000-0xfe4fffff]
[ 0.368989] pci 0000:00:1c.2: bridge window [io 0x0000-0x03af window] (subtractive decode)
[ 0.368990] pci 0000:00:1c.2: bridge window [io 0x03e0-0x0cf7 window] (subtractive decode)
[ 0.368992] pci 0000:00:1c.2: bridge window [io 0x03b0-0x03df window] (subtractive decode)
[ 0.368993] pci 0000:00:1c.2: bridge window [io 0x0d00-0xffff window] (subtractive decode)
[ 0.368994] pci 0000:00:1c.2: bridge window [mem 0x000a0000-0x000bffff window] (subtractive decode)
[ 0.368996] pci 0000:00:1c.2: bridge window [mem 0x000c0000-0x000dffff window] (subtractive decode)
[ 0.368997] pci 0000:00:1c.2: bridge window [mem 0xbfa00000-0xffffffff window] (subtractive decode)
[ 0.369057] pci_bus 0000:05: extended config space not accessible
[ 0.369092] pci 0000:05:00.0: [10b8:0005] type 00 class 0x020000
[ 0.369135] pci 0000:05:00.0: reg 0x10: [io 0xd100-0xd1ff]
[ 0.369159] pci 0000:05:00.0: reg 0x14: [mem 0xfe431000-0xfe431fff]
[ 0.369270] pci 0000:05:00.0: reg 0x30: [mem 0xfe420000-0xfe42ffff pref]
[ 0.369344] pci 0000:05:00.0: supports D1 D2
[ 0.369345] pci 0000:05:00.0: PME# supported from D1 D2 D3hot
[ 0.369424] pci 0000:05:01.0: [d161:8005] type 00 class 0x020000
[ 0.369467] pci 0000:05:01.0: reg 0x10: [io 0xd000-0xd0ff]
[ 0.369492] pci 0000:05:01.0: reg 0x14: [mem 0xfe430000-0xfe4303ff]
[ 0.369604] pci 0000:05:01.0: reg 0x30: [mem 0xfe400000-0xfe41ffff pref]
[ 0.369678] pci 0000:05:01.0: supports D1 D2
[ 0.369679] pci 0000:05:01.0: PME# supported from D0 D1 D2 D3hot D3cold
[ 0.369832] pci 0000:04:00.0: PCI bridge to [bus 05] (subtractive decode)
[ 0.369846] pci 0000:04:00.0: bridge window [io 0xd000-0xdfff]
[ 0.369854] pci 0000:04:00.0: bridge window [mem 0xfe400000-0xfe4fffff]
[ 0.369868] pci 0000:04:00.0: bridge window [io 0xd000-0xdfff] (subtractive decode)
[ 0.369869] pci 0000:04:00.0: bridge window [mem 0xfe400000-0xfe4fffff] (subtractive decode)
[ 0.369870] pci 0000:04:00.0: bridge window [io 0x0000-0x03af window] (subtractive decode)
[ 0.369872] pci 0000:04:00.0: bridge window [io 0x03e0-0x0cf7 window] (subtractive decode)
[ 0.369873] pci 0000:04:00.0: bridge window [io 0x03b0-0x03df window] (subtractive decode)
[ 0.369874] pci 0000:04:00.0: bridge window [io 0x0d00-0xffff window] (subtractive decode)
[ 0.369876] pci 0000:04:00.0: bridge window [mem 0x000a0000-0x000bffff window] (subtractive decode)
[ 0.369877] pci 0000:04:00.0: bridge window [mem 0x000c0000-0x000dffff window] (subtractive decode)
[ 0.369878] pci 0000:04:00.0: bridge window [mem 0xbfa00000-0xffffffff window] (subtractive decode)
[ 0.370509] ACPI: PCI Interrupt Link [LNKA] (IRQs 3 4 5 6 7 10 *11 12 14 15)
[ 0.370564] ACPI: PCI Interrupt Link [LNKB] (IRQs 3 4 *5 6 7 10 11 12 14 15)
[ 0.370616] ACPI: PCI Interrupt Link [LNKC] (IRQs *3 4 5 6 7 10 11 12 14 15)
[ 0.370668] ACPI: PCI Interrupt Link [LNKD] (IRQs 3 4 5 6 *7 10 12 14 15)
[ 0.370719] ACPI: PCI Interrupt Link [LNKE] (IRQs 3 4 5 6 7 10 11 12 14 15) *0
[ 0.370771] ACPI: PCI Interrupt Link [LNKF] (IRQs 3 4 5 6 7 10 11 12 14 15) *0
[ 0.370824] ACPI: PCI Interrupt Link [LNKG] (IRQs 3 4 5 6 7 *10 11 12 14 15)
[ 0.370876] ACPI: PCI Interrupt Link [LNKH] (IRQs 3 4 5 *6 7 10 11 12 14 15)
[ 0.371012] iommu: Default domain type: Translated
[ 0.371032] pci 0000:00:02.0: vgaarb: setting as boot VGA device
[ 0.371032] pci 0000:00:02.0: vgaarb: VGA device added: decodes=io+mem,owns=io+mem,locks=none
[ 0.371032] pci 0000:00:02.0: vgaarb: bridge control possible
[ 0.371032] vgaarb: loaded
[ 0.371032] EDAC MC: Ver: 3.0.0
[ 0.371032] NetLabel: Initializing
[ 0.371032] NetLabel: domain hash size = 128
[ 0.371032] NetLabel: protocols = UNLABELED CIPSOv4 CALIPSO
[ 0.371032] NetLabel: unlabeled traffic allowed by default
[ 0.371032] PCI: Using ACPI for IRQ routing
[ 0.378262] PCI: pci_cache_line_size set to 64 bytes
[ 0.378340] e820: reserve RAM buffer [mem 0x0009d800-0x0009ffff]
[ 0.378342] e820: reserve RAM buffer [mem 0xbad93000-0xbbffffff]
[ 0.378344] e820: reserve RAM buffer [mem 0xbae06000-0xbbffffff]
[ 0.378345] e820: reserve RAM buffer [mem 0xbb000000-0xbbffffff]
[ 0.378346] e820: reserve RAM buffer [mem 0x23fe00000-0x23fffffff]
[ 0.378385] hpet0: at MMIO 0xfed00000, IRQs 2, 8, 0, 0, 0, 0, 0, 0
[ 0.378391] hpet0: 8 comparators, 64-bit 14.318180 MHz counter
[ 0.380415] clocksource: Switched to clocksource tsc-early
[ 0.389530] VFS: Disk quotas dquot_6.6.0
[ 0.389547] VFS: Dquot-cache hash table entries: 512 (order 0, 4096 bytes)
[ 0.389676] AppArmor: AppArmor Filesystem Enabled
[ 0.389698] pnp: PnP ACPI init
[ 0.389848] system 00:00: [mem 0xfed10000-0xfed19fff] has been reserved
[ 0.389850] system 00:00: [mem 0xe0000000-0xefffffff] has been reserved
[ 0.389852] system 00:00: [mem 0xfed90000-0xfed93fff] has been reserved
[ 0.389853] system 00:00: [mem 0xfed20000-0xfed3ffff] has been reserved
[ 0.389855] system 00:00: [mem 0xfee00000-0xfee0ffff] has been reserved
[ 0.389863] system 00:00: Plug and Play ACPI device, IDs PNP0c01 (active)
[ 0.389994] system 00:01: [io 0x0a00-0x0a0f] has been reserved
[ 0.389997] system 00:01: [io 0x0a30-0x0a3f] has been reserved
[ 0.389999] system 00:01: [io 0x0a20-0x0a2f] has been reserved
[ 0.390003] system 00:01: Plug and Play ACPI device, IDs PNP0c02 (active)
[ 0.390297] pnp 00:02: Plug and Play ACPI device, IDs PNP0b00 (active)
[ 0.390352] system 00:03: [io 0x04d0-0x04d1] has been reserved
[ 0.390357] system 00:03: Plug and Play ACPI device, IDs PNP0c02 (active)
[ 0.390499] pnp 00:04: [dma 0 disabled]
[ 0.390547] pnp 00:04: Plug and Play ACPI device, IDs PNP0501 (active)
[ 0.390714] system 00:05: [io 0x0400-0x0453] has been reserved
[ 0.390715] system 00:05: [io 0x0458-0x047f] has been reserved
[ 0.390717] system 00:05: [io 0x1180-0x119f] has been reserved
[ 0.390718] system 00:05: [io 0x0500-0x057f] has been reserved
[ 0.390720] system 00:05: [mem 0xfed1c000-0xfed1ffff] has been reserved
[ 0.390722] system 00:05: [mem 0xfec00000-0xfecfffff] could not be reserved
[ 0.390724] system 00:05: [mem 0xfed08000-0xfed08fff] has been reserved
[ 0.390725] system 00:05: [mem 0xff000000-0xffffffff] has been reserved
[ 0.390730] system 00:05: Plug and Play ACPI device, IDs PNP0c01 (active)
[ 0.390789] system 00:06: [io 0x0454-0x0457] has been reserved
[ 0.390793] system 00:06: Plug and Play ACPI device, IDs INT3f0d PNP0c02 (active)
[ 0.390975] pnp: PnP ACPI: found 7 devices
[ 0.396935] clocksource: acpi_pm: mask: 0xffffff max_cycles: 0xffffff, max_idle_ns: 2085701024 ns
[ 0.397001] NET: Registered protocol family 2
[ 0.397126] IP idents hash table entries: 131072 (order: 8, 1048576 bytes, linear)
[ 0.398528] tcp_listen_portaddr_hash hash table entries: 4096 (order: 4, 65536 bytes, linear)
[ 0.398587] TCP established hash table entries: 65536 (order: 7, 524288 bytes, linear)
[ 0.398793] TCP bind hash table entries: 65536 (order: 8, 1048576 bytes, linear)
[ 0.398906] TCP: Hash tables configured (established 65536 bind 65536)
[ 0.398962] UDP hash table entries: 4096 (order: 5, 131072 bytes, linear)
[ 0.398997] UDP-Lite hash table entries: 4096 (order: 5, 131072 bytes, linear)
[ 0.399422] NET: Registered protocol family 1
[ 0.399429] NET: Registered protocol family 44
[ 0.399450] pci 0000:00:01.0: PCI bridge to [bus 01]
[ 0.399457] pci 0000:00:1c.0: PCI bridge to [bus 02]
[ 0.399461] pci 0000:00:1c.0: bridge window [io 0xe000-0xefff]
[ 0.399468] pci 0000:00:1c.0: bridge window [mem 0xd0000000-0xd00fffff 64bit pref]
[ 0.399475] pci 0000:00:1c.1: PCI bridge to [bus 03]
[ 0.399480] pci 0000:00:1c.1: bridge window [mem 0xfe500000-0xfe5fffff]
[ 0.399489] pci 0000:04:00.0: PCI bridge to [bus 05]
[ 0.399493] pci 0000:04:00.0: bridge window [io 0xd000-0xdfff]
[ 0.399504] pci 0000:04:00.0: bridge window [mem 0xfe400000-0xfe4fffff]
[ 0.399524] pci 0000:00:1c.2: PCI bridge to [bus 04-05]
[ 0.399527] pci 0000:00:1c.2: bridge window [io 0xd000-0xdfff]
[ 0.399532] pci 0000:00:1c.2: bridge window [mem 0xfe400000-0xfe4fffff]
[ 0.399541] pci_bus 0000:00: resource 4 [io 0x0000-0x03af window]
[ 0.399542] pci_bus 0000:00: resource 5 [io 0x03e0-0x0cf7 window]
[ 0.399543] pci_bus 0000:00: resource 6 [io 0x03b0-0x03df window]
[ 0.399545] pci_bus 0000:00: resource 7 [io 0x0d00-0xffff window]
[ 0.399546] pci_bus 0000:00: resource 8 [mem 0x000a0000-0x000bffff window]
[ 0.399547] pci_bus 0000:00: resource 9 [mem 0x000c0000-0x000dffff window]
[ 0.399549] pci_bus 0000:00: resource 10 [mem 0xbfa00000-0xffffffff window]
[ 0.399550] pci_bus 0000:02: resource 0 [io 0xe000-0xefff]
[ 0.399552] pci_bus 0000:02: resource 2 [mem 0xd0000000-0xd00fffff 64bit pref]
[ 0.399553] pci_bus 0000:03: resource 1 [mem 0xfe500000-0xfe5fffff]
[ 0.399554] pci_bus 0000:04: resource 0 [io 0xd000-0xdfff]
[ 0.399556] pci_bus 0000:04: resource 1 [mem 0xfe400000-0xfe4fffff]
[ 0.399557] pci_bus 0000:04: resource 4 [io 0x0000-0x03af window]
[ 0.399558] pci_bus 0000:04: resource 5 [io 0x03e0-0x0cf7 window]
[ 0.399559] pci_bus 0000:04: resource 6 [io 0x03b0-0x03df window]
[ 0.399560] pci_bus 0000:04: resource 7 [io 0x0d00-0xffff window]
[ 0.399562] pci_bus 0000:04: resource 8 [mem 0x000a0000-0x000bffff window]
[ 0.399563] pci_bus 0000:04: resource 9 [mem 0x000c0000-0x000dffff window]
[ 0.399564] pci_bus 0000:04: resource 10 [mem 0xbfa00000-0xffffffff window]
[ 0.399566] pci_bus 0000:05: resource 0 [io 0xd000-0xdfff]
[ 0.399567] pci_bus 0000:05: resource 1 [mem 0xfe400000-0xfe4fffff]
[ 0.399568] pci_bus 0000:05: resource 4 [io 0xd000-0xdfff]
[ 0.399569] pci_bus 0000:05: resource 5 [mem 0xfe400000-0xfe4fffff]
[ 0.399570] pci_bus 0000:05: resource 6 [io 0x0000-0x03af window]
[ 0.399572] pci_bus 0000:05: resource 7 [io 0x03e0-0x0cf7 window]
[ 0.399573] pci_bus 0000:05: resource 8 [io 0x03b0-0x03df window]
[ 0.399574] pci_bus 0000:05: resource 9 [io 0x0d00-0xffff window]
[ 0.399575] pci_bus 0000:05: resource 10 [mem 0x000a0000-0x000bffff window]
[ 0.399577] pci_bus 0000:05: resource 11 [mem 0x000c0000-0x000dffff window]
[ 0.399578] pci_bus 0000:05: resource 12 [mem 0xbfa00000-0xffffffff window]
[ 0.399659] pci 0000:00:02.0: BIOS left Intel GPU interrupts enabled; disabling
[ 0.399674] pci 0000:00:02.0: Video device with shadowed ROM at [mem 0x000c0000-0x000dffff]
[ 0.400141] PCI: CLS 64 bytes, default 64
[ 0.400197] Trying to unpack rootfs image as initramfs...
[ 0.976187] Freeing initrd memory: 32044K
[ 0.976196] PCI-DMA: Using software bounce buffering for IO (SWIOTLB)
[ 0.976198] software IO TLB: mapped [mem 0x00000000b6d93000-0x00000000bad93000] (64MB)
[ 0.976635] Initialise system trusted keyrings
[ 0.976645] Key type blacklist registered
[ 0.976700] workingset: timestamp_bits=36 max_order=21 bucket_order=0
[ 0.977919] zbud: loaded
[ 0.978096] integrity: Platform Keyring initialized
[ 0.978099] Key type asymmetric registered
[ 0.978100] Asymmetric key parser 'x509' registered
[ 0.978109] Block layer SCSI generic (bsg) driver version 0.4 loaded (major 251)
[ 0.978159] io scheduler mq-deadline registered
[ 0.978392] pcieport 0000:00:01.0: PME: Signaling with IRQ 24
[ 0.978560] pcieport 0000:00:1c.0: PME: Signaling with IRQ 25
[ 0.978672] pcieport 0000:00:1c.1: PME: Signaling with IRQ 26
[ 0.978837] pcieport 0000:00:1c.2: PME: Signaling with IRQ 27
[ 0.978924] shpchp: Standard Hot Plug PCI Controller Driver version: 0.4
[ 0.978935] intel_idle: MWAIT substates: 0x1120
[ 0.978937] intel_idle: v0.5.1 model 0x2A
[ 0.978939] intel_idle: max_cstate 1 reached
[ 0.978987] intel_idle: Local APIC timer is reliable in all C-states
[ 0.979594] thermal LNXTHERM:00: registered as thermal_zone0
[ 0.979595] ACPI: Thermal Zone [THRM] (35 C)
[ 0.979712] Serial: 8250/16550 driver, 4 ports, IRQ sharing enabled
[ 0.979874] 00:04: ttyS0 at I/O 0x3f8 (irq = 4, base_baud = 115200) is a 16550A
[ 0.980608] Linux agpgart interface v0.103
[ 0.980645] AMD-Vi: AMD IOMMUv2 functionality not available on this system - This is not a bug.
[ 0.980784] i8042: PNP: No PS/2 controller found.
[ 0.980836] mousedev: PS/2 mouse device common for all mice
[ 0.980870] rtc_cmos 00:02: RTC can wake from S4
[ 0.981068] rtc_cmos 00:02: registered as rtc0
[ 0.981098] rtc_cmos 00:02: setting system clock to 2022-01-18T05:04:56 UTC (1642482296)
[ 0.981113] rtc_cmos 00:02: alarms up to one month, y3k, 114 bytes nvram, hpet irqs
[ 0.981123] intel_pstate: Intel P-state driver initializing
[ 0.981242] ledtrig-cpu: registered to indicate activity on CPUs
[ 0.981584] NET: Registered protocol family 10
[ 0.989959] Segment Routing with IPv6
[ 0.989987] mip6: Mobile IPv6
[ 0.989990] NET: Registered protocol family 17
[ 0.990027] mpls_gso: MPLS GSO support
[ 0.990196] microcode: sig=0x206a7, pf=0x2, revision=0x14
[ 0.990205] microcode: Microcode Update Driver: v2.2.
[ 0.990210] IPI shorthand broadcast: enabled
[ 0.990218] sched_clock: Marking stable (988126423, 2004944)->(1215598138, -225466771)
[ 0.990304] registered taskstats version 1
[ 0.990306] Loading compiled-in X.509 certificates
[ 1.036670] Loaded X.509 cert 'Debian Secure Boot CA: 6ccece7e4c6c0d1f6149f3dd27dfcc5cbb419ea1'
[ 1.036690] Loaded X.509 cert 'Debian Secure Boot Signer 2021 - linux: 4b6ef5abca669825178e052c84667ccbc0531f8c'
[ 1.036712] zswap: loaded using pool lzo/zbud
[ 1.036821] Key type ._fscrypt registered
[ 1.036822] Key type .fscrypt registered
[ 1.036823] Key type fscrypt-provisioning registered
[ 1.036862] AppArmor: AppArmor sha1 policy hashing enabled
[ 1.038510] Freeing unused kernel image (initmem) memory: 2408K
[ 1.057857] Write protecting the kernel read-only data: 22528k
[ 1.058329] Freeing unused kernel image (text/rodata gap) memory: 2040K
[ 1.058476] Freeing unused kernel image (rodata/data gap) memory: 628K
[ 1.124403] x86/mm: Checked W+X mappings: passed, no W+X pages found.
[ 1.124405] x86/mm: Checking user space page tables
[ 1.184322] x86/mm: Checked W+X mappings: passed, no W+X pages found.
[ 1.184330] Run /init as init process
[ 1.184331] with arguments:
[ 1.184332] /init
[ 1.184333] with environment:
[ 1.184334] HOME=/
[ 1.184335] TERM=linux
[ 1.184335] BOOT_IMAGE=/boot/vmlinuz-5.10.0-10-amd64
[ 1.270083] epic100.c:v1.11 1/7/2001 Written by Donald Becker <becker@scyld.com> (unofficial 2.4.x kernel port, version 2.1, Sept 11, 2006)
[ 1.270450] epic100 0000:05:00.0: MII transceiver #3 control 3000 status 7849.
[ 1.271442] epic100 0000:05:00.0: Autonegotiation advertising 01e1 link partner 0001.
[ 1.271602] epic100 0000:05:00.0 eth0: SMSC EPIC/100 83c170 at d100, IRQ 18, 00:e0:29:62:43:c0
[ 1.278470] ACPI: bus type USB registered
[ 1.278493] usbcore: registered new interface driver usbfs
[ 1.278501] usbcore: registered new interface driver hub
[ 1.278513] usbcore: registered new device driver usb
[ 1.283356] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
[ 1.284185] ehci-pci: EHCI PCI platform driver
[ 1.284317] ehci-pci 0000:00:1a.0: EHCI Host Controller
[ 1.284324] ehci-pci 0000:00:1a.0: new USB bus registered, assigned bus number 1
[ 1.284342] ehci-pci 0000:00:1a.0: debug port 2
[ 1.287810] SCSI subsystem initialized
[ 1.288256] ehci-pci 0000:00:1a.0: cache line size of 64 is not supported
[ 1.288288] ehci-pci 0000:00:1a.0: irq 16, io mem 0xfe607000
[ 1.298348] i801_smbus 0000:00:1f.3: SMBus using PCI interrupt
[ 1.298739] i2c i2c-0: 2/4 memory slots populated (from DMI)
[ 1.301873] ehci-pci 0000:00:1a.0: USB 2.0 started, EHCI 1.00
[ 1.301936] usb usb1: New USB device found, idVendor=1d6b, idProduct=0002, bcdDevice= 5.10
[ 1.301938] usb usb1: New USB device strings: Mfr=3, Product=2, SerialNumber=1
[ 1.301939] usb usb1: Product: EHCI Host Controller
[ 1.301941] usb usb1: Manufacturer: Linux 5.10.0-10-amd64 ehci_hcd
[ 1.301942] usb usb1: SerialNumber: 0000:00:1a.0
[ 1.302073] hub 1-0:1.0: USB hub found
[ 1.302081] hub 1-0:1.0: 2 ports detected
[ 1.302285] i2c i2c-0: Successfully instantiated SPD at 0x50
[ 1.302348] ehci-pci 0000:00:1d.0: EHCI Host Controller
[ 1.302355] ehci-pci 0000:00:1d.0: new USB bus registered, assigned bus number 2
[ 1.302368] ehci-pci 0000:00:1d.0: debug port 2
[ 1.302953] i2c i2c-0: Successfully instantiated SPD at 0x52
[ 1.306292] ehci-pci 0000:00:1d.0: cache line size of 64 is not supported
[ 1.317697] ehci-pci 0000:00:1d.0: irq 23, io mem 0xfe606000
[ 1.330293] ehci-pci 0000:00:1d.0: USB 2.0 started, EHCI 1.00
[ 1.330523] usb usb2: New USB device found, idVendor=1d6b, idProduct=0002, bcdDevice= 5.10
[ 1.330525] usb usb2: New USB device strings: Mfr=3, Product=2, SerialNumber=1
[ 1.330527] usb usb2: Product: EHCI Host Controller
[ 1.330528] usb usb2: Manufacturer: Linux 5.10.0-10-amd64 ehci_hcd
[ 1.330529] usb usb2: SerialNumber: 0000:00:1d.0
[ 1.330821] hub 2-0:1.0: USB hub found
[ 1.330987] hub 2-0:1.0: 2 ports detected
[ 1.334907] epic100 0000:05:00.0 eth1: renamed from eth0
[ 1.343437] libphy: r8169: probed
[ 1.347200] libata version 3.00 loaded.
[ 1.349205] xhci_hcd 0000:03:00.0: xHCI Host Controller
[ 1.349214] xhci_hcd 0000:03:00.0: new USB bus registered, assigned bus number 3
[ 1.353515] ahci 0000:00:1f.2: version 3.0
[ 1.353764] ahci 0000:00:1f.2: AHCI 0001.0300 32 slots 4 ports 3 Gbps 0x33 impl SATA mode
[ 1.353767] ahci 0000:00:1f.2: flags: 64bit ncq sntf pm led clo pio slum part ems apst
[ 1.354033] r8169 0000:02:00.0 eth0: RTL8168e/8111e, 00:30:67:c4:67:6f, XID 2c2, IRQ 28
[ 1.354035] r8169 0000:02:00.0 eth0: jumbo features [frames: 9194 bytes, tx checksumming: ko]
[ 1.356382] xhci_hcd 0000:03:00.0: hcc params 0x0200f180 hci version 0x96 quirks 0x0000000000080000
[ 1.356634] usb usb3: New USB device found, idVendor=1d6b, idProduct=0002, bcdDevice= 5.10
[ 1.356636] usb usb3: New USB device strings: Mfr=3, Product=2, SerialNumber=1
[ 1.356637] usb usb3: Product: xHCI Host Controller
[ 1.356638] usb usb3: Manufacturer: Linux 5.10.0-10-amd64 xhci-hcd
[ 1.356639] usb usb3: SerialNumber: 0000:03:00.0
[ 1.356762] hub 3-0:1.0: USB hub found
[ 1.356774] hub 3-0:1.0: 2 ports detected
[ 1.356935] xhci_hcd 0000:03:00.0: xHCI Host Controller
[ 1.356939] xhci_hcd 0000:03:00.0: new USB bus registered, assigned bus number 4
[ 1.356942] xhci_hcd 0000:03:00.0: Host supports USB 3.0 SuperSpeed
[ 1.361399] usb usb4: We don't know the algorithms for LPM for this host, disabling LPM.
[ 1.361422] usb usb4: New USB device found, idVendor=1d6b, idProduct=0003, bcdDevice= 5.10
[ 1.361423] usb usb4: New USB device strings: Mfr=3, Product=2, SerialNumber=1
[ 1.361425] usb usb4: Product: xHCI Host Controller
[ 1.361426] usb usb4: Manufacturer: Linux 5.10.0-10-amd64 xhci-hcd
[ 1.361427] usb usb4: SerialNumber: 0000:03:00.0
[ 1.361538] hub 4-0:1.0: USB hub found
[ 1.361549] hub 4-0:1.0: 2 ports detected
[ 1.394412] scsi host0: ahci
[ 1.394566] scsi host1: ahci
[ 1.394684] scsi host2: ahci
[ 1.394794] scsi host3: ahci
[ 1.394912] scsi host4: ahci
[ 1.395026] scsi host5: ahci
[ 1.395076] ata1: SATA max UDMA/133 abar m2048@0xfe605000 port 0xfe605100 irq 29
[ 1.395079] ata2: SATA max UDMA/133 abar m2048@0xfe605000 port 0xfe605180 irq 29
[ 1.395080] ata3: DUMMY
[ 1.395081] ata4: DUMMY
[ 1.395083] ata5: SATA max UDMA/133 abar m2048@0xfe605000 port 0xfe605300 irq 29
[ 1.395086] ata6: SATA max UDMA/133 abar m2048@0xfe605000 port 0xfe605380 irq 29
[ 1.557850] usb 1-1: new high-speed USB device number 2 using ehci-pci
[ 1.585848] usb 2-1: new high-speed USB device number 2 using ehci-pci
[ 1.707967] ata5: SATA link down (SStatus 0 SControl 300)
[ 1.707989] ata2: SATA link up 3.0 Gbps (SStatus 123 SControl 300)
[ 1.708006] ata1: SATA link up 3.0 Gbps (SStatus 123 SControl 300)
[ 1.708020] ata6: SATA link down (SStatus 0 SControl 300)
[ 1.709606] ata1.00: ATA-8: WDC WD2002FAEX-00MJRA0, 01.01L01, max UDMA/133
[ 1.709608] ata1.00: 3907029168 sectors, multi 16: LBA48 NCQ (depth 32), AA
[ 1.710476] ata1.00: configured for UDMA/133
[ 1.710573] scsi 0:0:0:0: Direct-Access ATA WDC WD2002FAEX-0 1L01 PQ: 0 ANSI: 5
[ 1.726241] usb 1-1: New USB device found, idVendor=8087, idProduct=0024, bcdDevice= 0.00
[ 1.726243] usb 1-1: New USB device strings: Mfr=0, Product=0, SerialNumber=0
[ 1.726482] hub 1-1:1.0: USB hub found
[ 1.726616] hub 1-1:1.0: 4 ports detected
[ 1.745276] ata2.00: ATA-10: ST2000DM008-2FR102, 0001, max UDMA/133
[ 1.745278] ata2.00: 3907029168 sectors, multi 16: LBA48 NCQ (depth 32), AA
[ 1.746246] usb 2-1: New USB device found, idVendor=8087, idProduct=0024, bcdDevice= 0.00
[ 1.746250] usb 2-1: New USB device strings: Mfr=0, Product=0, SerialNumber=0
[ 1.746559] hub 2-1:1.0: USB hub found
[ 1.746752] hub 2-1:1.0: 6 ports detected
[ 1.794892] ata2.00: configured for UDMA/133
[ 1.795032] scsi 1:0:0:0: Direct-Access ATA ST2000DM008-2FR1 0001 PQ: 0 ANSI: 5
[ 1.805626] sd 0:0:0:0: [sda] 3907029168 512-byte logical blocks: (2.00 TB/1.82 TiB)
[ 1.805633] sd 1:0:0:0: [sdb] 3907029168 512-byte logical blocks: (2.00 TB/1.82 TiB)
[ 1.805636] sd 1:0:0:0: [sdb] 4096-byte physical blocks
[ 1.805639] sd 0:0:0:0: [sda] Write Protect is off
[ 1.805641] sd 0:0:0:0: [sda] Mode Sense: 00 3a 00 00
[ 1.805646] sd 1:0:0:0: [sdb] Write Protect is off
[ 1.805648] sd 1:0:0:0: [sdb] Mode Sense: 00 3a 00 00
[ 1.805659] sd 0:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
[ 1.805665] sd 1:0:0:0: [sdb] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
[ 1.845925] sda: sda1 sda2
[ 1.847816] sdb: sdb1 sdb2
[ 1.861963] sd 0:0:0:0: [sda] Attached SCSI disk
[ 1.861977] sd 1:0:0:0: [sdb] Attached SCSI disk
[ 1.993868] tsc: Refined TSC clocksource calibration: 2394.560 MHz
[ 1.993877] clocksource: tsc: mask: 0xffffffffffffffff max_cycles: 0x2284248580e, max_idle_ns: 440795288736 ns
[ 1.993918] clocksource: Switched to clocksource tsc
[ 2.013869] usb 1-1.1: new high-speed USB device number 3 using ehci-pci
[ 2.021455] md/raid1:md0: active with 2 out of 2 mirrors
[ 2.021478] md0: detected capacity change from 0 to 1995264819200
[ 2.028954] random: fast init done
[ 2.081229] random: lvm: uninitialized urandom read (4 bytes read)
[ 2.111560] device-mapper: uevent: version 1.0.3
[ 2.111656] device-mapper: ioctl: 4.43.0-ioctl (2020-10-01) initialised: dm-devel@redhat.com
[ 2.112691] random: lvm: uninitialized urandom read (2 bytes read)
[ 2.123402] usb 1-1.1: New USB device found, idVendor=03f0, idProduct=8d11, bcdDevice= 1.00
[ 2.123406] usb 1-1.1: New USB device strings: Mfr=1, Product=2, SerialNumber=3
[ 2.123407] usb 1-1.1: Product: Photosmart D110 series
[ 2.123408] usb 1-1.1: Manufacturer: HP
[ 2.123410] usb 1-1.1: SerialNumber: CN13SG31BH05N9
[ 2.130118] usb-storage 1-1.1:1.3: USB Mass Storage device detected
[ 2.130353] scsi host6: usb-storage 1-1.1:1.3
[ 2.130439] usbcore: registered new interface driver usb-storage
[ 2.132333] usbcore: registered new interface driver uas
[ 2.209853] usb 1-1.3: new low-speed USB device number 4 using ehci-pci
[ 2.324136] usb 1-1.3: New USB device found, idVendor=413c, idProduct=2003, bcdDevice= 3.06
[ 2.324139] usb 1-1.3: New USB device strings: Mfr=1, Product=2, SerialNumber=0
[ 2.324141] usb 1-1.3: Product: Dell USB Keyboard
[ 2.324142] usb 1-1.3: Manufacturer: Dell
[ 2.332765] hid: raw HID events driver (C) Jiri Kosina
[ 2.339877] usbcore: registered new interface driver usbhid
[ 2.339879] usbhid: USB HID core driver
[ 2.341704] input: Dell Dell USB Keyboard as /devices/pci0000:00/0000:00:1a.0/usb1/1-1/1-1.3/1-1.3:1.0/0003:413C:2003.0001/input/input0
[ 2.397982] hid-generic 0003:413C:2003.0001: input,hidraw0: USB HID v1.10 Keyboard [Dell Dell USB Keyboard] on usb-0000:00:1a.0-1.3/input0
[ 2.401859] usb 1-1.4: new low-speed USB device number 5 using ehci-pci
[ 2.515012] usb 1-1.4: New USB device found, idVendor=045e, idProduct=0040, bcdDevice= 3.00
[ 2.515015] usb 1-1.4: New USB device strings: Mfr=1, Product=3, SerialNumber=0
[ 2.515017] usb 1-1.4: Product: Microsoft 3-Button Mouse with IntelliEye(TM)
[ 2.515018] usb 1-1.4: Manufacturer: Microsoft
[ 2.517873] input: Microsoft Microsoft 3-Button Mouse with IntelliEye(TM) as /devices/pci0000:00/0000:00:1a.0/usb1/1-1/1-1.4/1-1.4:1.0/0003:045E:0040.0002/input/input1
[ 2.517951] hid-generic 0003:045E:0040.0002: input,hidraw1: USB HID v1.10 Mouse [Microsoft Microsoft 3-Button Mouse with IntelliEye(TM)] on usb-0000:00:1a.0-1.4/input0
[ 2.873847] raid6: sse2x4 gen() 9500 MB/s
[ 2.941843] raid6: sse2x4 xor() 5457 MB/s
[ 3.009843] raid6: sse2x2 gen() 11514 MB/s
[ 3.077843] raid6: sse2x2 xor() 6274 MB/s
[ 3.145847] raid6: sse2x1 gen() 9134 MB/s
[ 3.146520] scsi 6:0:0:0: Direct-Access HP Photosmart D110 1.00 PQ: 0 ANSI: 5
[ 3.213844] raid6: sse2x1 xor() 5702 MB/s
[ 3.213845] raid6: using algorithm sse2x2 gen() 11514 MB/s
[ 3.213846] raid6: .... xor() 6274 MB/s, rmw enabled
[ 3.213848] raid6: using ssse3x2 recovery algorithm
[ 3.214882] xor: measuring software checksum speed
[ 3.215575] prefetch64-sse : 14251 MB/sec
[ 3.216325] generic_sse : 13124 MB/sec
[ 3.216326] xor: using function: prefetch64-sse (14251 MB/sec)
[ 3.217049] async_tx: api initialized (async)
[ 3.248775] random: lvm: uninitialized urandom read (4 bytes read)
[ 3.258647] sd 6:0:0:0: [sdc] Attached SCSI removable disk
[ 3.336094] random: lvm: uninitialized urandom read (4 bytes read)
[ 3.392799] PM: Image not found (code -22)
[ 3.565943] EXT4-fs (dm-0): mounted filesystem with ordered data mode. Opts: (null)
[ 3.711494] Not activating Mandatory Access Control as /sbin/tomoyo-init does not exist.
[ 3.852045] random: crng init done
[ 4.462820] systemd[1]: Inserted module 'autofs4'
[ 4.565582] systemd[1]: systemd 247.3-6 running in system mode. (+PAM +AUDIT +SELINUX +IMA +APPARMOR +SMACK +SYSVINIT +UTMP +LIBCRYPTSETUP +GCRYPT +GNUTLS +ACL +XZ +LZ4 +ZSTD +SECCOMP +BLKID +ELFUTILS +KMOD +IDN2 -IDN +PCRE2 default-hierarchy=unified)
[ 4.581923] systemd[1]: Detected architecture x86-64.
[ 4.598634] systemd[1]: Set hostname to <precession>.
[ 5.656693] systemd[1]: Queued start job for default target Graphical Interface.
[ 5.657762] systemd[1]: Created slice system-getty.slice.
[ 5.658087] systemd[1]: Created slice system-modprobe.slice.
[ 5.658386] systemd[1]: Created slice system-postfix.slice.
[ 5.658626] systemd[1]: Created slice system-systemd\x2dfsck.slice.
[ 5.658846] systemd[1]: Created slice User and Session Slice.
[ 5.658978] systemd[1]: Started Dispatch Password Requests to Console Directory Watch.
[ 5.659042] systemd[1]: Started Forward Password Requests to Wall Directory Watch.
[ 5.659225] systemd[1]: Set up automount Arbitrary Executable File Formats File System Automount Point.
[ 5.659287] systemd[1]: Reached target Local Encrypted Volumes.
[ 5.659338] systemd[1]: Reached target Slices.
[ 5.659361] systemd[1]: Reached target TLS tunnels for network services - per-config-file target.
[ 5.659463] systemd[1]: Listening on Device-mapper event daemon FIFOs.
[ 5.667465] systemd[1]: Listening on LVM2 poll daemon socket.
[ 5.677430] systemd[1]: Listening on RPCbind Server Activation Socket.
[ 5.683268] systemd[1]: Listening on Syslog Socket.
[ 5.683391] systemd[1]: Listening on fsck to fsckd communication Socket.
[ 5.683473] systemd[1]: Listening on initctl Compatibility Named Pipe.
[ 5.683658] systemd[1]: Listening on Journal Audit Socket.
[ 5.683767] systemd[1]: Listening on Journal Socket (/dev/log).
[ 5.683895] systemd[1]: Listening on Journal Socket.
[ 5.684044] systemd[1]: Listening on udev Control Socket.
[ 5.684137] systemd[1]: Listening on udev Kernel Socket.
[ 5.685010] systemd[1]: Mounting Huge Pages File System...
[ 5.685988] systemd[1]: Mounting POSIX Message Queue File System...
[ 5.687127] systemd[1]: Mounting Kernel Debug File System...
[ 5.688128] systemd[1]: Mounting Kernel Trace File System...
[ 5.688363] systemd[1]: Finished Availability of block devices.
[ 5.689467] systemd[1]: Starting Set the console keyboard layout...
[ 5.690521] systemd[1]: Starting Create list of static device nodes for the current kernel...
[ 5.691485] systemd[1]: Starting Monitoring of LVM2 mirrors, snapshots etc. using dmeventd or progress polling...
[ 5.692766] systemd[1]: Starting Load Kernel Module configfs...
[ 5.693916] systemd[1]: Starting Load Kernel Module drm...
[ 5.694988] systemd[1]: Starting Load Kernel Module fuse...
[ 5.702042] systemd[1]: Condition check resulted in Set Up Additional Binary Formats being skipped.
[ 5.702116] systemd[1]: Condition check resulted in File System Check on Root Device being skipped.
[ 5.704078] systemd[1]: Starting Journal Service...
[ 5.711980] systemd[1]: Starting Load Kernel Modules...
[ 5.712946] systemd[1]: Starting Remount Root and Kernel File Systems...
[ 5.714059] systemd[1]: Starting Coldplug All udev Devices...
[ 5.720544] systemd[1]: Mounted Huge Pages File System.
[ 5.720685] systemd[1]: Mounted POSIX Message Queue File System.
[ 5.720785] systemd[1]: Mounted Kernel Debug File System.
[ 5.720880] systemd[1]: Mounted Kernel Trace File System.
[ 5.721128] systemd[1]: modprobe@configfs.service: Succeeded.
[ 5.721368] systemd[1]: Finished Load Kernel Module configfs.
[ 5.722994] systemd[1]: Mounting Kernel Configuration File System...
[ 5.724252] systemd[1]: Finished Create list of static device nodes for the current kernel.
[ 5.733222] systemd[1]: Mounted Kernel Configuration File System.
[ 5.779404] systemd[1]: Finished Monitoring of LVM2 mirrors, snapshots etc. using dmeventd or progress polling.
[ 5.805980] fuse: init (API version 7.32)
[ 5.806709] systemd[1]: modprobe@fuse.service: Succeeded.
[ 5.806999] systemd[1]: Finished Load Kernel Module fuse.
[ 5.808044] systemd[1]: Mounting FUSE Control File System...
[ 5.811767] systemd[1]: Mounted FUSE Control File System.
[ 5.818339] EXT4-fs (dm-0): re-mounted. Opts: errors=remount-ro
[ 5.819405] systemd[1]: Finished Remount Root and Kernel File Systems.
[ 5.841381] systemd[1]: Condition check resulted in Rebuild Hardware Database being skipped.
[ 5.842430] systemd[1]: Starting Create System Users...
[ 5.853310] systemd[1]: modprobe@drm.service: Succeeded.
[ 5.853551] systemd[1]: Finished Load Kernel Module drm.
[ 5.920522] systemd[1]: Started Journal Service.
[ 6.069910] loop: module loaded
[ 6.418926] input: Power Button as /devices/LNXSYSTM:00/LNXSYBUS:00/PNP0C0C:00/input/input2
[ 6.433937] ACPI: Power Button [PWRB]
[ 6.434013] input: Power Button as /devices/LNXSYSTM:00/LNXPWRBN:00/input/input3
[ 6.434057] ACPI: Power Button [PWRF]
[ 6.454796] sd 0:0:0:0: Attached scsi generic sg0 type 0
[ 6.454831] sd 1:0:0:0: Attached scsi generic sg1 type 0
[ 6.454862] sd 6:0:0:0: Attached scsi generic sg2 type 0
[ 6.496536] input: PC Speaker as /devices/platform/pcspkr/input/input4
[ 6.526384] at24 0-0050: supply vcc not found, using dummy regulator
[ 6.527623] at24 0-0050: 256 byte spd EEPROM, read-only
[ 6.527656] at24 0-0052: supply vcc not found, using dummy regulator
[ 6.528259] at24 0-0052: 256 byte spd EEPROM, read-only
[ 6.598193] iTCO_vendor_support: vendor-support=0
[ 6.605202] iTCO_wdt: Intel TCO WatchDog Timer Driver v1.11
[ 6.605250] iTCO_wdt: Found a Cougar Point TCO device (Version=2, TCOBASE=0x0460)
[ 6.605367] iTCO_wdt: initialized. heartbeat=30 sec (nowayout=0)
[ 6.632727] RAPL PMU: API unit is 2^-32 Joules, 3 fixed counters, 163840 ms ovfl timer
[ 6.632730] RAPL PMU: hw unit of domain pp0-core 2^-16 Joules
[ 6.632731] RAPL PMU: hw unit of domain package 2^-16 Joules
[ 6.632732] RAPL PMU: hw unit of domain pp1-gpu 2^-16 Joules
[ 6.646461] cryptd: max_cpu_qlen set to 1000
[ 6.806550] Setting dangerous option enable_dc - tainting kernel
[ 6.806554] Setting dangerous option disable_power_well - tainting kernel
[ 6.807352] i915 0000:00:02.0: vgaarb: deactivate vga console
[ 6.807769] Console: switching to colour dummy device 80x25
[ 6.809089] i915 0000:00:02.0: vgaarb: changed VGA decodes: olddecodes=io+mem,decodes=io+mem:owns=io+mem
[ 6.830282] [drm] Initialized i915 1.6.0 20200917 for 0000:00:02.0 on minor 0
[ 6.956767] usblp 1-1.1:1.1: usblp0: USB Bidirectional printer dev 3 if 1 alt 0 proto 2 vid 0x03F0 pid 0x8D11
[ 6.956804] usbcore: registered new interface driver usblp
[ 6.984263] fbcon: i915drmfb (fb0) is primary device
[ 7.085524] Console: switching to colour frame buffer device 240x67
[ 7.106537] i915 0000:00:02.0: [drm] fb0: i915drmfb frame buffer device
[ 7.161229] intel_rapl_common: Found RAPL domain package
[ 7.161232] intel_rapl_common: Found RAPL domain core
[ 7.161233] intel_rapl_common: Found RAPL domain uncore
[ 7.349390] snd_hda_intel 0000:00:1b.0: bound 0000:00:02.0 (ops i915_audio_component_bind_ops [i915])
[ 7.440966] EXT4-fs (dm-1): mounting ext2 file system using the ext4 subsystem
[ 7.441746] snd_hda_codec_realtek hdaudioC0D2: autoconfig for ALC662 rev1: line_outs=1 (0x14/0x0/0x0/0x0/0x0) type:line
[ 7.441749] snd_hda_codec_realtek hdaudioC0D2: speaker_outs=0 (0x0/0x0/0x0/0x0/0x0)
[ 7.441750] snd_hda_codec_realtek hdaudioC0D2: hp_outs=1 (0x1b/0x0/0x0/0x0/0x0)
[ 7.441752] snd_hda_codec_realtek hdaudioC0D2: mono: mono_out=0x0
[ 7.441753] snd_hda_codec_realtek hdaudioC0D2: dig-out=0x1e/0x0
[ 7.441754] snd_hda_codec_realtek hdaudioC0D2: inputs:
[ 7.441756] snd_hda_codec_realtek hdaudioC0D2: Front Mic=0x19
[ 7.441757] snd_hda_codec_realtek hdaudioC0D2: Rear Mic=0x18
[ 7.441758] snd_hda_codec_realtek hdaudioC0D2: Line=0x1a
[ 7.505857] Adding 409596k swap on /dev/mapper/precession-swap. Priority:-2 extents:1 across:409596k FS
[ 7.530580] input: HDA Intel PCH Front Mic as /devices/pci0000:00/0000:00:1b.0/sound/card0/input5
[ 7.530632] input: HDA Intel PCH Rear Mic as /devices/pci0000:00/0000:00:1b.0/sound/card0/input6
[ 7.530680] input: HDA Intel PCH Line as /devices/pci0000:00/0000:00:1b.0/sound/card0/input7
[ 7.530728] input: HDA Intel PCH Line Out as /devices/pci0000:00/0000:00:1b.0/sound/card0/input8
[ 7.530774] input: HDA Intel PCH Front Headphone as /devices/pci0000:00/0000:00:1b.0/sound/card0/input9
[ 7.531364] input: HDA Intel PCH HDMI/DP,pcm=3 as /devices/pci0000:00/0000:00:1b.0/sound/card0/input10
[ 7.585437] EXT4-fs (dm-1): mounted filesystem without journal. Opts: (null)
[ 7.585447] ext2 filesystem being mounted at /tmp supports timestamps until 2038 (0x7fffffff)
[ 7.727858] EXT4-fs (dm-2): mounted filesystem with ordered data mode. Opts: (null)
[ 7.788729] systemd-journald[279]: Received client request to flush runtime journal.
[ 8.215490] EXT4-fs (dm-3): mounted filesystem with ordered data mode. Opts: (null)
[ 8.595527] EXT4-fs (dm-4): mounted filesystem with ordered data mode. Opts: (null)
[ 8.789508] r8169 0000:02:00.0: firmware: direct-loading firmware rtl_nic/rtl8168e-2.fw
[ 8.790229] RTL8211DN Gigabit Ethernet r8169-0-200:00: attached PHY driver [RTL8211DN Gigabit Ethernet] (mii_bus:phy_addr=r8169-0-200:00, irq=IGNORE)
[ 9.038934] r8169 0000:02:00.0 eth0: Link is Down
[ 9.743136] Process accounting resumed
[ 11.136620] r8169 0000:02:00.0 eth0: Link is Up - 1Gbps/Full - flow control rx/tx
[ 11.136634] IPv6: ADDRCONF(NETDEV_CHANGE): eth0: link becomes ready
[22807.411314] Process accounting resumed
[44965.165351] [drm:fw_domains_get [i915]] *ERROR* render: timed out waiting for forcewake ack request.
[44965.165439] i915 0000:00:02.0: [drm:add_taint_for_CI [i915]] CI tainted:0x9 by fw_domains_get+0x167/0x1b0 [i915]
[44965.170442] ------------[ cut here ]------------
[44965.170443] i915 0000:00:02.0: GT thread status wait timed out
[44965.170507] WARNING: CPU: 1 PID: 61 at drivers/gpu/drm/i915/intel_uncore.c:327 __gen6_gt_wait_for_thread_c0+0x84/0x90 [i915]
[44965.170508] Modules linked in: xt_multiport ip6_tables xt_conntrack nf_conntrack nf_defrag_ipv6 nf_defrag_ipv4 xt_tcpudp ip6t_REJECT nf_reject_ipv6 ipt_REJECT nf_reject_ipv4 nf_log_ipv6 nf_log_ipv4 nf_log_common nft_limit xt_LOG nft_compat xt_limit nft_counter nf_tables nfnetlink snd_hda_codec_hdmi snd_hda_codec_realtek snd_hda_codec_generic ledtrig_audio snd_hda_intel snd_intel_dspcfg soundwire_intel soundwire_generic_allocation intel_rapl_msr intel_rapl_common x86_pkg_temp_thermal intel_powerclamp coretemp kvm_intel snd_soc_core snd_compress soundwire_cadence usblp snd_hda_codec kvm snd_hda_core irqbypass i915 snd_hwdep ghash_clmulni_intel soundwire_bus mei_hdcp cryptd evdev rapl intel_cstate snd_pcm iTCO_wdt intel_pmc_bxt iTCO_vendor_support snd_timer watchdog intel_uncore snd video at24 pcspkr soundcore drm_kms_helper mei_me sg cec mei i2c_algo_bit button drm loop fuse configfs ip_tables x_tables autofs4 ext4 crc16 mbcache jbd2 raid10 raid456 async_raid6_recov async_memcpy async_pq
[44965.170584] async_xor async_tx xor raid6_pq libcrc32c crc32c_generic raid0 multipath linear hid_generic usbhid hid uas usb_storage dm_mod raid1 md_mod sd_mod t10_pi crc_t10dif crct10dif_generic ahci libahci xhci_pci xhci_hcd libata r8169 crct10dif_pclmul crct10dif_common realtek crc32_pclmul crc32c_intel mdio_devres libphy i2c_i801 i2c_smbus scsi_mod ehci_pci ehci_hcd lpc_ich usbcore epic100 mii usb_common
[44965.170627] CPU: 1 PID: 61 Comm: kworker/1:1H Tainted: G U W 5.10.0-10-amd64 #1 Debian 5.10.84-1
[44965.170628] Hardware name: BIOSTAR Group H61MU3/H61MU3, BIOS 4.6.4 04/07/2011
[44965.170674] Workqueue: events_highpri heartbeat [i915]
[44965.170717] RIP: 0010:__gen6_gt_wait_for_thread_c0+0x84/0x90 [i915]
[44965.170720] Code: 22 00 01 48 8b 78 18 4c 8b 67 50 4d 85 e4 75 03 4c 8b 27 e8 4e 9e 32 e1 4c 89 e2 48 c7 c7 38 fb a5 c0 48 89 c6 e8 0f 80 58 e1 <0f> 0b eb bc 0f 1f 84 00 00 00 00 00 66 66 66 66 90 89 f0 41 54 48
[44965.170722] RSP: 0018:ffffa8c18015bc48 EFLAGS: 00010086
[44965.170725] RAX: 0000000000000000 RBX: ffff8a7c03bc0808 RCX: ffff8a7d37b1ca08
[44965.170726] RDX: 00000000ffffffd8 RSI: 0000000000000027 RDI: ffff8a7d37b1ca00
[44965.170728] RBP: 000028e544b6a1a6 R08: 0000000000000000 R09: ffffa8c18015ba68
[44965.170729] R10: ffffa8c18015ba60 R11: ffffffffa2ccb408 R12: ffff8a7d37bd9890
[44965.170731] R13: 0000000000000001 R14: ffff8a7c03bc0820 R15: 0000000000000000
[44965.170733] FS: 0000000000000000(0000) GS:ffff8a7d37b00000(0000) knlGS:0000000000000000
[44965.170735] CS: 0010 DS: 0000 ES: 0000 CR0: 0000000080050033
[44965.170737] CR2: 00007fd080192198 CR3: 00000001bc8a4001 CR4: 00000000000606e0
[44965.170738] Call Trace:
[44965.170784] gen6_read32+0x118/0x1e0 [i915]
[44965.170841] intel_gt_coredump_alloc+0x12e/0x720 [i915]
[44965.170897] i915_gpu_coredump+0x56/0x430 [i915]
[44965.170951] i915_capture_error_state+0xf/0x70 [i915]
[44965.170999] intel_gt_handle_error+0x2e2/0x300 [i915]
[44965.171006] ? record_times+0x15/0x90
[44965.171009] ? psi_group_change+0x41/0x220
[44965.171054] heartbeat+0x327/0x3b0 [i915]
[44965.171060] process_one_work+0x1b6/0x350
[44965.171064] worker_thread+0x53/0x3e0
[44965.171067] ? process_one_work+0x350/0x350
[44965.171070] kthread+0x11b/0x140
[44965.171073] ? __kthread_bind_mask+0x60/0x60
[44965.171077] ret_from_fork+0x22/0x30
[44965.171081] ---[ end trace 15f63bd6b3c01dac ]---
[44965.221174] [drm:fw_domains_get [i915]] *ERROR* render: timed out waiting for forcewake ack request.
[44965.221252] i915 0000:00:02.0: [drm:add_taint_for_CI [i915]] CI tainted:0x9 by fw_domains_get+0x167/0x1b0 [i915]
[44965.261091] i915 0000:00:02.0: [drm] GPU HANG: ecode 6:2:ecdfbff0, in systemd-logind [654]
[44965.262164] i915 0000:00:02.0: [drm] Resetting chip for stopped heartbeat on bcs0
I have a few more files saved with dmesg & drm/card0/error messages and
some notes describing some of my other experiments. I can add them if
you think it might help.
I still have not found a stable configuration for this system which used
to have fast video. I will keep experimenting and reporting results that
might help with the debugging. Any advice for providing better debugging
would be welcome.
--
CJ Fearnley | LinuxForce Inc.
cjf@LinuxForce.net | Hosting and Linux Consulting
https://www.LinuxForce.net | https://blog.LinuxForce.net
Reply to: