--- Begin Message ---
- To: Debian Bug Tracking System <submit@bugs.debian.org>
- Subject: linux-image-3.2.0-3-686-pae: mounting sd-card via usb-card-reader freezes system
- From: spamfang <spamfang1199@yahoo.de>
- Date: Sun, 22 Jul 2012 22:07:34 +0200
- Message-id: <20120722200734.2486.56894.reportbug@hugo3>
Package: src
Version: 3.2.21-3
Severity: critical
Justification: causes serious data loss
While writing this bug report, my machine froze because i tried to mount a sd-
card via a usb-card reader, connected to a usb2.0-pci-card.
Always when i try to mount my mobile phone (Nokia 500) or my mp3-stick
(trexstore organic) or just the naked sd-card via card-reader, I open up
Dolphin and click on the appearing sd-card-entry. Then Dolphin tries to mount
the card. But no luck: Sometimes it tries to mount it and for a brief moment
its beginning to show the folders and subfolders. But then it vanishes aprupt
and the card gets unmounted.
The system immediately tries to remount it, but this fails in 90% of cases. In
the 10% remaining cases, it gets remounted, but only in very slow USB1.0 mode.
And still it does not transfer the data completely.
This bug affects also some machine of friends, one with a medion MD6200.
Also portable 2,5inch hard drives are affected. It seems any device which gets
its power from the USB-port has these problems.
Needles to say: On both machines no problem under XP or CentOS6
Filesystems need check after remount
-- Package-specific info:
** Version:
Linux version 3.2.0-3-686-pae (Debian 3.2.21-3) (debian-kernel@lists.debian.org) (gcc version 4.6.3 (Debian 4.6.3-8) ) #1 SMP Thu Jun 28 08:56:46 UTC 2012
** Command line:
BOOT_IMAGE=/vmlinuz-3.2.0-3-686-pae root=/dev/mapper/hda9_crypt ro quiet radeon.modeset=0
** Not tainted
** Kernel log:
[ 1.668959] uhci_hcd 0000:00:11.4: new USB bus registered, assigned bus number 5
[ 1.668983] uhci_hcd 0000:00:11.4: irq 10, io base 0x0000e400
[ 1.669036] usb usb5: New USB device found, idVendor=1d6b, idProduct=0001
[ 1.669039] usb usb5: New USB device strings: Mfr=3, Product=2, SerialNumber=1
[ 1.669043] usb usb5: Product: UHCI Host Controller
[ 1.669045] usb usb5: Manufacturer: Linux 3.2.0-3-686-pae uhci_hcd
[ 1.669048] usb usb5: SerialNumber: 0000:00:11.4
[ 1.670493] hub 5-0:1.0: USB hub found
[ 1.670507] hub 5-0:1.0: 2 ports detected
[ 1.670647] pata_via 0000:00:11.1: version 0.3.4
[ 1.670673] pata_via 0000:00:11.1: PCI INT A -> Link[LNKA] -> GSI 11 (level, low) -> IRQ 11
[ 1.670679] pata_via 0000:00:11.1: VIA VLink IRQ fixup, from 255 to 11
[ 1.674855] scsi0 : pata_via
[ 1.680110] Refined TSC clocksource calibration: 2071.022 MHz.
[ 1.680122] Switching to clocksource tsc
[ 1.682200] scsi1 : pata_via
[ 1.685107] ata1: PATA max UDMA/100 cmd 0x1f0 ctl 0x3f6 bmdma 0xd800 irq 14
[ 1.685112] ata2: PATA max UDMA/100 cmd 0x170 ctl 0x376 bmdma 0xd808 irq 15
[ 1.685220] ohci_hcd 0000:00:09.1: PCI INT B -> Link[LNKC] -> GSI 5 (level, low) -> IRQ 5
[ 1.685259] ohci_hcd 0000:00:09.1: OHCI Host Controller
[ 1.685283] ohci_hcd 0000:00:09.1: new USB bus registered, assigned bus number 6
[ 1.685319] ohci_hcd 0000:00:09.1: irq 5, io mem 0xea001000
[ 1.769881] usb usb6: New USB device found, idVendor=1d6b, idProduct=0001
[ 1.769887] usb usb6: New USB device strings: Mfr=3, Product=2, SerialNumber=1
[ 1.769891] usb usb6: Product: OHCI Host Controller
[ 1.769893] usb usb6: Manufacturer: Linux 3.2.0-3-686-pae ohci_hcd
[ 1.769896] usb usb6: SerialNumber: 0000:00:09.1
[ 1.770284] hub 6-0:1.0: USB hub found
[ 1.770294] hub 6-0:1.0: 2 ports detected
[ 1.892630] ata1.00: ATA-7: ST3500630A, 3.AAF, max UDMA/100
[ 1.892635] ata1.00: 976773168 sectors, multi 16: LBA48
[ 1.959172] ata1.00: configured for UDMA/100
[ 1.959393] scsi 0:0:0:0: Direct-Access ATA ST3500630A 3.AA PQ: 0 ANSI: 5
[ 1.980046] usb 3-1: new full-speed USB device number 2 using uhci_hcd
[ 2.120305] ata2.00: ATAPI: HL-DT-ST DVDRAM GSA-H12N, UL02, max UDMA/66
[ 2.120311] ata2.00: limited to UDMA/33 due to 40-wire cable
[ 2.136221] ata2.00: configured for UDMA/33
[ 2.141988] scsi 1:0:0:0: CD-ROM HL-DT-ST DVDRAM GSA-H12N UL02 PQ: 0 ANSI: 5
[ 2.160848] sd 0:0:0:0: [sda] 976773168 512-byte logical blocks: (500 GB/465 GiB)
[ 2.160926] sd 0:0:0:0: [sda] Write Protect is off
[ 2.160931] sd 0:0:0:0: [sda] Mode Sense: 00 3a 00 00
[ 2.160964] sd 0:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
[ 2.165873] sr0: scsi3-mmc drive: 48x/48x writer dvd-ram cd/rw xa/form2 cdda tray
[ 2.165881] cdrom: Uniform CD-ROM driver Revision: 3.20
[ 2.166377] sr 1:0:0:0: Attached scsi CD-ROM sr0
[ 2.167970] usb 3-1: New USB device found, idVendor=046d, idProduct=08da
[ 2.167975] usb 3-1: New USB device strings: Mfr=0, Product=0, SerialNumber=0
[ 2.247301] sda: sda1 sda2 < sda5 sda6 sda7 sda8 sda9 sda10 >
[ 2.248446] sd 0:0:0:0: [sda] Attached SCSI disk
[ 2.989260] device-mapper: uevent: version 1.0.3
[ 2.989793] device-mapper: ioctl: 4.22.0-ioctl (2011-10-19) initialised: dm-devel@redhat.com
[ 6.407357] EXT3-fs (dm-0): recovery required on readonly filesystem
[ 6.407364] EXT3-fs (dm-0): write access will be enabled during recovery
[ 6.673437] kjournald starting. Commit interval 5 seconds
[ 6.673486] EXT3-fs (dm-0): recovery complete
[ 6.673970] EXT3-fs (dm-0): mounted filesystem with ordered data mode
[ 8.723674] udevd[320]: starting version 175
[ 9.313338] Marking TSC unstable due to TSC halts in idle
[ 9.313356] ACPI: acpi_idle registered with cpuidle
[ 9.322207] Switching to clocksource acpi_pm
[ 9.358111] input: PC Speaker as /devices/platform/pcspkr/input/input4
[ 9.392124] powernow: PowerNOW! Technology present. Can scale: frequency and voltage.
[ 9.399231] powernow: Trying ACPI perflib
[ 9.399794] powernow: ACPI perflib can not be used on this platform
[ 9.399798] powernow: ACPI and legacy methods failed
[ 9.749200] shpchp: Standard Hot Plug PCI Controller Driver version: 0.4
[ 9.853987] NET: Registered protocol family 23
[ 10.169115] gameport gameport0: NS558 PnP Gameport is pnp00:0c/gameport0, io 0x201, speed 1065kHz
[ 10.254272] parport_pc 00:09: reported by Plug and Play ACPI
[ 10.254322] parport0: PC-style at 0x378, irq 7 [PCSPP,TRISTATE]
[ 10.386018] Linux media interface: v0.10
[ 10.476554] Linux video capture interface: v2.00
[ 10.499990] gspca_main: v2.14.0 registered
[ 10.549832] gspca_main: zc3xx-2.14.0 probing 046d:08da
[ 10.579297] input: ImPS/2 Logitech Wheel Mouse as /devices/platform/i8042/serio1/input/input5
[ 10.952549] snd_cmipci 0000:00:0b.0: PCI INT A -> Link[LNKD] -> GSI 10 (level, low) -> IRQ 10
[ 11.645528] input: zc3xx as /devices/pci0000:00/0000:00:11.2/usb3/3-1/input/input6
[ 11.647443] usbcore: registered new interface driver zc3xx
[ 11.650838] usbcore: registered new interface driver snd-usb-audio
[ 13.343827] EXT3-fs (dm-0): using internal journal
[ 14.648480] loop: module loaded
[ 15.900940] kjournald starting. Commit interval 5 seconds
[ 15.901104] EXT3-fs (sda9): using internal journal
[ 15.901111] EXT3-fs (sda9): mounted filesystem with ordered data mode
[ 15.997358] FAT-fs (sda5): utf8 is not a recommended IO charset for FAT filesystems, filesystem will be case sensitive!
[ 16.209982] kjournald starting. Commit interval 5 seconds
[ 16.210439] EXT3-fs (dm-1): using internal journal
[ 16.210443] EXT3-fs (dm-1): recovery complete
[ 16.210674] EXT3-fs (dm-1): mounted filesystem with ordered data mode
[ 17.202813] fuse init (API version 7.17)
[ 20.492475] 8139too 0000:00:0d.0: eth0: link up, 100Mbps, full-duplex, lpa 0x45E1
[ 21.879108] input: ACPI Virtual Keyboard Device as /devices/virtual/input/input7
[ 22.812197] agpgart-via 0000:00:00.0: AGP 2.0 bridge
[ 22.812223] agpgart-via 0000:00:00.0: putting AGP V2 device into 4x mode
[ 22.812275] pci 0000:01:00.0: putting AGP V2 device into 4x mode
[ 23.178960] [drm] Setting GART location based on new memory map
[ 23.179068] [drm] Loading R300 Microcode
[ 23.282099] [drm] Num pipes: 1
[ 23.282108] [drm] writeback test succeeded in 1 usecs
[ 31.472031] eth0: no IPv6 routers present
** Model information
not available
** Loaded modules:
uinput
fuse
nls_utf8
nls_cp437
vfat
fat
loop
snd_usb_audio
snd_cmipci
snd_mpu401_uart
snd_usbmidi_lib
snd_seq_midi
snd_seq_midi_event
snd_rawmidi
snd_opl3_lib
snd_hwdep
snd_pcm
gspca_zc3xx
snd_page_alloc
snd_seq
gspca_main
videodev
snd_seq_device
snd_timer
media
snd
parport_pc
ns558
i2c_viapro
soundcore
gameport
via_ircc
irda
psmouse
crc_ccitt
shpchp
serio_raw
evdev
parport
pcspkr
processor
ext3
mbcache
jbd
sha256_generic
cryptd
aes_i586
aes_generic
cbc
dm_crypt
dm_mod
sr_mod
sd_mod
crc_t10dif
cdrom
ata_generic
radeon
power_supply
i2c_algo_bit
drm_kms_helper
ttm
drm
pata_via
libata
uhci_hcd
scsi_mod
ohci_hcd
floppy
ehci_hcd
usbcore
fan
thermal
thermal_sys
i2c_core
button
8139too
8139cp
mii
usb_common
** PCI devices:
00:00.0 Host bridge [0600]: VIA Technologies, Inc. VT8366/A/7 [Apollo KT266/A/333] [1106:3099]
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort+ >SERR- <PERR- INTx-
Latency: 0
Region 0: Memory at d0000000 (32-bit, prefetchable) [size=128M]
Capabilities: <access denied>
Kernel driver in use: agpgart-via
00:01.0 PCI bridge [0604]: VIA Technologies, Inc. VT8366/A/7 [Apollo KT266/A/333 AGP] [1106:b099] (prog-if 00 [Normal decode])
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz+ UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort+ >SERR- <PERR- INTx-
Latency: 0
Bus: primary=00, secondary=01, subordinate=01, sec-latency=0
I/O behind bridge: 0000c000-0000cfff
Memory behind bridge: e8000000-e9ffffff
Prefetchable memory behind bridge: d8000000-e7ffffff
Secondary status: 66MHz- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- <SERR- <PERR-
BridgeCtl: Parity- SERR- NoISA+ VGA+ MAbort- >Reset- FastB2B-
PriDiscTmr- SecDiscTmr- DiscTmrStat- DiscTmrSERREn-
Capabilities: <access denied>
00:09.0 USB controller [0c03]: NEC Corporation USB [1033:0035] (rev 43) (prog-if 10 [OHCI])
Subsystem: NEC Corporation Hama USB 2.0 CardBus [1033:0035]
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 32 (250ns min, 10500ns max), Cache Line Size: 32 bytes
Interrupt: pin A routed to IRQ 11
Region 0: Memory at ea000000 (32-bit, non-prefetchable) [size=4K]
Capabilities: <access denied>
Kernel driver in use: ohci_hcd
00:09.1 USB controller [0c03]: NEC Corporation USB [1033:0035] (rev 43) (prog-if 10 [OHCI])
Subsystem: NEC Corporation Hama USB 2.0 CardBus [1033:0035]
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 32 (250ns min, 10500ns max), Cache Line Size: 32 bytes
Interrupt: pin B routed to IRQ 5
Region 0: Memory at ea001000 (32-bit, non-prefetchable) [size=4K]
Capabilities: <access denied>
Kernel driver in use: ohci_hcd
00:09.2 USB controller [0c03]: NEC Corporation USB 2.0 [1033:00e0] (rev 04) (prog-if 20 [EHCI])
Subsystem: Device [1838:1074]
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV+ VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 32 (4000ns min, 8500ns max), Cache Line Size: 32 bytes
Interrupt: pin C routed to IRQ 10
Region 0: Memory at ea002000 (32-bit, non-prefetchable) [size=256]
Capabilities: <access denied>
Kernel driver in use: ehci_hcd
00:0b.0 Multimedia audio controller [0401]: C-Media Electronics Inc CM8738 [13f6:0111] (rev 10)
Subsystem: C-Media Electronics Inc CMI8738/C3DX PCI Audio Device [13f6:0111]
Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 32 (500ns min, 6000ns max)
Interrupt: pin A routed to IRQ 10
Region 0: I/O ports at d000 [size=256]
Capabilities: <access denied>
Kernel driver in use: snd_cmipci
00:0d.0 Ethernet controller [0200]: Realtek Semiconductor Co., Ltd. RTL-8139/8139C/8139C+ [10ec:8139] (rev 10)
Subsystem: Compex FN22-3(A) LinxPRO Ethernet Adapter [11f6:8139]
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 32 (8000ns min, 16000ns max)
Interrupt: pin A routed to IRQ 10
Region 0: I/O ports at d400 [size=256]
Region 1: Memory at ea003000 (32-bit, non-prefetchable) [size=256]
Capabilities: <access denied>
Kernel driver in use: 8139too
00:11.0 ISA bridge [0601]: VIA Technologies, Inc. VT8233 PCI to ISA Bridge [1106:3074]
Subsystem: VIA Technologies, Inc. VT8233 PCI to ISA Bridge [1106:3074]
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping+ SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0
Capabilities: <access denied>
00:11.1 IDE interface [0101]: VIA Technologies, Inc. VT82C586A/B/VT82C686/A/B/VT823x/A/C PIPC Bus Master IDE [1106:0571] (rev 06) (prog-if 8a [Master SecP PriP])
Subsystem: VIA Technologies, Inc. VT82C586/B/VT82C686/A/B/VT8233/A/C/VT8235 PIPC Bus Master IDE [1106:0571]
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 32
Interrupt: pin A routed to IRQ 11
Region 0: [virtual] Memory at 000001f0 (32-bit, non-prefetchable) [size=8]
Region 1: [virtual] Memory at 000003f0 (type 3, non-prefetchable) [size=1]
Region 2: [virtual] Memory at 00000170 (32-bit, non-prefetchable) [size=8]
Region 3: [virtual] Memory at 00000370 (type 3, non-prefetchable) [size=1]
Region 4: I/O ports at d800 [size=16]
Capabilities: <access denied>
Kernel driver in use: pata_via
00:11.2 USB controller [0c03]: VIA Technologies, Inc. VT82xxxxx UHCI USB 1.1 Controller [1106:3038] (rev 1b) (prog-if 00 [UHCI])
Subsystem: First International Computer, Inc. VA-502 Mainboard [0925:1234]
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 32, Cache Line Size: 32 bytes
Interrupt: pin D routed to IRQ 10
Region 4: I/O ports at dc00 [size=32]
Capabilities: <access denied>
Kernel driver in use: uhci_hcd
00:11.3 USB controller [0c03]: VIA Technologies, Inc. VT82xxxxx UHCI USB 1.1 Controller [1106:3038] (rev 1b) (prog-if 00 [UHCI])
Subsystem: First International Computer, Inc. VA-502 Mainboard [0925:1234]
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 32, Cache Line Size: 32 bytes
Interrupt: pin D routed to IRQ 10
Region 4: I/O ports at e000 [size=32]
Capabilities: <access denied>
Kernel driver in use: uhci_hcd
00:11.4 USB controller [0c03]: VIA Technologies, Inc. VT82xxxxx UHCI USB 1.1 Controller [1106:3038] (rev 1b) (prog-if 00 [UHCI])
Subsystem: First International Computer, Inc. VA-502 Mainboard [0925:1234]
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 32, Cache Line Size: 32 bytes
Interrupt: pin D routed to IRQ 10
Region 4: I/O ports at e400 [size=32]
Capabilities: <access denied>
Kernel driver in use: uhci_hcd
01:00.0 VGA compatible controller [0300]: Advanced Micro Devices [AMD] nee ATI RV350 AR [Radeon 9600] [1002:4152] (prog-if 00 [VGA controller])
Subsystem: Hightech Information System Ltd. Device [17af:2016]
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz+ UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 32 (2000ns min), Cache Line Size: 32 bytes
Interrupt: pin A routed to IRQ 11
Region 0: Memory at d8000000 (32-bit, prefetchable) [size=128M]
Region 1: I/O ports at c000 [size=256]
Region 2: Memory at e9000000 (32-bit, non-prefetchable) [size=64K]
[virtual] Expansion ROM at e8000000 [disabled] [size=128K]
Capabilities: <access denied>
01:00.1 Display controller [0380]: Advanced Micro Devices [AMD] nee ATI RV350 AR [Radeon 9600] (Secondary) [1002:4172]
Subsystem: Hightech Information System Ltd. Device [17af:2017]
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz+ UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 32 (2000ns min), Cache Line Size: 32 bytes
Region 0: Memory at e0000000 (32-bit, prefetchable) [size=128M]
Region 1: Memory at e9010000 (32-bit, non-prefetchable) [size=64K]
Capabilities: <access denied>
** USB devices:
Bus 001 Device 001: ID 1d6b:0002 Linux Foundation 2.0 root hub
Bus 002 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub
Bus 003 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub
Bus 004 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub
Bus 005 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub
Bus 006 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub
Bus 003 Device 002: ID 046d:08da Logitech, Inc. QuickCam Messanger
-- System Information:
Debian Release: wheezy/sid
APT prefers testing
APT policy: (500, 'testing')
Architecture: i386 (i686)
Kernel: Linux 3.2.0-3-686-pae (SMP w/1 CPU core)
Locale: LANG=de_DE.UTF-8, LC_CTYPE=de_DE.UTF-8 (charmap=UTF-8)
Shell: /bin/sh linked to /bin/dash
Versions of packages linux-image-3.2.0-3-686-pae depends on:
ii debconf [debconf-2.0] 1.5.44
ii initramfs-tools [linux-initramfs-tool] 0.107
ii kmod 8-2
ii linux-base 3.5
ii module-init-tools 8-2
Versions of packages linux-image-3.2.0-3-686-pae recommends:
ii firmware-linux-free 3.1
ii libc6-i686 2.13-33
Versions of packages linux-image-3.2.0-3-686-pae suggests:
pn debian-kernel-handbook <none>
ii grub-pc 1.99-22.1
pn linux-doc-3.2 <none>
Versions of packages linux-image-3.2.0-3-686-pae is related to:
pn firmware-atheros <none>
pn firmware-bnx2 <none>
pn firmware-bnx2x <none>
pn firmware-brcm80211 <none>
pn firmware-intelwimax <none>
pn firmware-ipw2x00 <none>
pn firmware-ivtv <none>
pn firmware-iwlwifi <none>
pn firmware-libertas <none>
ii firmware-linux 0.36
ii firmware-linux-nonfree 0.36
pn firmware-myricom <none>
pn firmware-netxen <none>
pn firmware-qlogic <none>
pn firmware-ralink <none>
pn firmware-realtek <none>
pn xen-hypervisor <none>
-- debconf information:
linux-image-3.2.0-3-686-pae/postinst/ignoring-ramdisk:
linux-image-3.2.0-3-686-pae/postinst/depmod-error-initrd-3.2.0-3-686-pae: false
linux-image-3.2.0-3-686-pae/postinst/missing-firmware-3.2.0-3-686-pae:
linux-image-3.2.0-3-686-pae/prerm/removing-running-kernel-3.2.0-3-686-pae: true
--- End Message ---