--- Begin Message ---
- To: Debian Bug Tracking System <submit@bugs.debian.org>
- Subject: linux-image-3.10-3-amd64: USB 3 drive resets and comes up as new device in middle of cp
- From: eli <eli_venter@yahoo.com>
- Date: Fri, 11 Oct 2013 14:13:57 -0400
- Message-id: <20131011181357.32692.48242.reportbug@gdx-dev3.bioreference-laboratories.com>
Package: src:linux
Version: 3.10.11-1
Severity: important
Dear Maintainer,
USB 3 padlock(pin protected) drive connects fine, I mount it read-only (ntfs/fuseblk) then
begin cp off of the drive. After a while the cp fails because the device
has gone away, changing from sdd to sde. umount, power cycle device
and it comes back up fine again for a while.
-- Package-specific info:
** Version:
Linux version 3.10-3-amd64 (debian-kernel@lists.debian.org) (gcc version 4.7.3 (Debian 4.7.3-7) ) #1 SMP Debian 3.10.11-1 (2013-09-10)
** Command line:
BOOT_IMAGE=/boot/vmlinuz-3.10-3-amd64 root=UUID=b06d965c-f5f6-4eef-87f4-0d6e364f9e78 ro quiet
** Not tainted
** Kernel log:
[342208.971194] usb 2-1: new SuperSpeed USB device number 3 using xhci_hcd
[342208.987632] usb 2-1: New USB device found, idVendor=0984, idProduct=0315
[342208.987634] usb 2-1: New USB device strings: Mfr=1, Product=2, SerialNumber=3
[342208.987636] usb 2-1: Product: Padlock DT 3.0
[342208.987637] usb 2-1: Manufacturer: Apricorn
[342208.987638] usb 2-1: SerialNumber: 573144313335525820202020
[342208.988326] usb-storage 2-1:1.0: USB Mass Storage device detected
[342208.988447] scsi6 : usb-storage 2-1:1.0
[342209.988598] scsi 6:0:0:0: Direct-Access Apricorn Padlock DT 3.0 0120 PQ: 0 ANSI: 6
[342209.988832] sd 6:0:0:0: Attached scsi generic sg4 type 0
[342209.989100] sd 6:0:0:0: [sdd] 1953525168 512-byte logical blocks: (1.00 TB/931 GiB)
[342209.989371] sd 6:0:0:0: [sdd] Write Protect is off
[342209.989374] sd 6:0:0:0: [sdd] Mode Sense: 2b 00 10 08
[342209.989618] sd 6:0:0:0: [sdd] Write cache: enabled, read cache: enabled, supports DPO and FUA
[342210.011388] sdd: sdd1
[342210.012424] sd 6:0:0:0: [sdd] Attached SCSI disk
[346717.767819] usb 2-1: reset SuperSpeed USB device number 3 using xhci_hcd
[346717.783887] xhci_hcd 0000:00:14.0: xHCI xhci_drop_endpoint called with disabled ep ffff8804112e7800
[346717.783890] xhci_hcd 0000:00:14.0: xHCI xhci_drop_endpoint called with disabled ep ffff8804112e77c0
[346964.203946] usb 2-1: reset SuperSpeed USB device number 3 using xhci_hcd
[346964.220010] xhci_hcd 0000:00:14.0: xHCI xhci_drop_endpoint called with disabled ep ffff8804112e7800
[346964.220013] xhci_hcd 0000:00:14.0: xHCI xhci_drop_endpoint called with disabled ep ffff8804112e77c0
[346964.471854] usb 1-1: new high-speed USB device number 4 using xhci_hcd
[346964.471943] usb 1-1: Device not responding to set address.
[346964.676049] usb 1-1: Device not responding to set address.
[346964.880004] usb 1-1: device not accepting address 4, error -71
[346964.992073] usb 1-1: new high-speed USB device number 5 using xhci_hcd
[346964.992147] usb 1-1: Device not responding to set address.
[346965.196251] usb 1-1: Device not responding to set address.
[346965.400244] usb 1-1: device not accepting address 5, error -71
[346965.512294] usb 1-1: new high-speed USB device number 6 using xhci_hcd
[346965.512388] usb 1-1: Device not responding to set address.
[346965.716467] usb 1-1: Device not responding to set address.
[346965.920465] usb 1-1: device not accepting address 6, error -71
[346966.032515] usb 1-1: new high-speed USB device number 7 using xhci_hcd
[346966.032619] usb 1-1: Device not responding to set address.
[346966.236690] usb 1-1: Device not responding to set address.
[346966.440681] usb 1-1: device not accepting address 7, error -71
[346966.440717] hub 1-0:1.0: unable to enumerate USB device on port 1
[346966.608766] usb 2-1: USB disconnect, device number 3
[346969.229876] usb 2-1: Disable of device-initiated U1 failed.
[346969.750084] usb 2-1: device not accepting address 3, error -22
[346970.270301] usb 2-1: device not accepting address 3, error -22
[346970.790522] usb 2-1: device not accepting address 3, error -22
[346971.310740] usb 2-1: device not accepting address 3, error -22
[346971.350751] sd 6:0:0:0: [sdd] Unhandled error code
[346971.350754] sd 6:0:0:0: [sdd]
[346971.350755] Result: hostbyte=DID_NO_CONNECT driverbyte=DRIVER_OK
[346971.350756] sd 6:0:0:0: [sdd] CDB:
[346971.350757] Read(10): 28 00 61 a3 d8 00 00 00 f0 00
[346971.350762] end_request: I/O error, dev sdd, sector 1638127616
[346971.350789] Buffer I/O error on device sdd1, logical block 204765696
[346971.350814] Buffer I/O error on device sdd1, logical block 204765697
[346971.350836] Buffer I/O error on device sdd1, logical block 204765698
[346971.350856] sd 6:0:0:0: [sdd] Unhandled error code
[346971.350857] sd 6:0:0:0: [sdd]
[346971.350859] Result: hostbyte=DID_NO_CONNECT driverbyte=DRIVER_OK
[346971.350860] sd 6:0:0:0: [sdd] CDB:
[346971.350865] Buffer I/O error on device sdd1, logical block 204765699
[346971.350861] Read(10): 28 00 61 a3 d8 f0 00 00 10 00
[346971.350869] end_request: I/O error, dev sdd, sector 1638127856
[346971.350871] Buffer I/O error on device sdd1, logical block 204765726
[346971.350872] Buffer I/O error on device sdd1, logical block 204765727
[346971.350951] Buffer I/O error on device sdd1, logical block 204765700
[346971.350972] Buffer I/O error on device sdd1, logical block 204765701
[346971.350994] Buffer I/O error on device sdd1, logical block 204765702
[346971.351015] Buffer I/O error on device sdd1, logical block 204765703
[346972.285641] sd 6:0:0:0: [sdd] Synchronizing SCSI cache
[346972.285665] sd 6:0:0:0: [sdd]
[346972.285667] Result: hostbyte=DID_NO_CONNECT driverbyte=DRIVER_OK
[346972.285866] xhci_hcd 0000:00:14.0: xHCI xhci_drop_endpoint called with disabled ep ffff8804112e7800
[346972.285868] xhci_hcd 0000:00:14.0: xHCI xhci_drop_endpoint called with disabled ep ffff8804112e77c0
[346972.523295] usb 2-1: new SuperSpeed USB device number 4 using xhci_hcd
[346972.539679] usb 2-1: New USB device found, idVendor=0984, idProduct=0315
[346972.539682] usb 2-1: New USB device strings: Mfr=1, Product=2, SerialNumber=3
[346972.539683] usb 2-1: Product: Padlock DT 3.0
[346972.539685] usb 2-1: Manufacturer: Apricorn
[346972.539686] usb 2-1: SerialNumber: 573144313335525820202020
[346972.540367] usb-storage 2-1:1.0: USB Mass Storage device detected
[346972.540497] scsi7 : usb-storage 2-1:1.0
[346973.540670] scsi 7:0:0:0: Direct-Access Apricorn Padlock DT 3.0 0120 PQ: 0 ANSI: 6
[346973.540853] sd 7:0:0:0: Attached scsi generic sg4 type 0
[346973.541296] sd 7:0:0:0: [sde] 1953525168 512-byte logical blocks: (1.00 TB/931 GiB)
[346973.541552] sd 7:0:0:0: [sde] Write Protect is off
[346973.541555] sd 7:0:0:0: [sde] Mode Sense: 2b 00 10 08
[346973.541803] sd 7:0:0:0: [sde] Write cache: enabled, read cache: enabled, supports DPO and FUA
[346973.564518] sde: unknown partition table
[346973.565430] sd 7:0:0:0: [sde] Attached SCSI disk
[348240.382824] usb 2-1: USB disconnect, device number 4
[348240.383349] sd 7:0:0:0: [sde] Synchronizing SCSI cache
[348240.383438] sd 7:0:0:0: [sde]
[348240.383441] Result: hostbyte=DID_NO_CONNECT driverbyte=DRIVER_OK
[348240.383576] usb 2-1: Set SEL for device-initiated U1 failed.
[348240.383579] usb 2-1: Set SEL for device-initiated U2 failed.
** Model information
sys_vendor:
product_name:
product_version:
chassis_vendor:
chassis_version:
bios_vendor: Intel Corp.
bios_version: RLH8710H.86A.0320.2013.0606.1802
board_vendor: Intel Corporation
board_name: DH87RL
board_version: AAG74240-400
** Loaded modules:
usb_storage
nfsv3
rpcsec_gss_krb5
nfsv4
arc4
ecb
md4
sha256_generic
hmac
nls_utf8
cifs
ip6table_filter
ip6_tables
iptable_filter
ip_tables
ebtable_nat
ebtables
x_tables
nfsd
auth_rpcgss
oid_registry
nfs_acl
nfs
lockd
dns_resolver
fscache
sunrpc
dm_cache_mq
dm_cache
dm_persistent_data
dm_bufio
dm_bio_prison
fuse
adt7475
hwmon_vid
coretemp
kvm_intel
kvm
crc32c_intel
ghash_clmulni_intel
aesni_intel
aes_x86_64
iTCO_wdt
ablk_helper
nouveau
mxm_wmi
wmi
cryptd
mei_me
mei
lrw
gf128mul
iTCO_vendor_support
ttm
glue_helper
i915
drm_kms_helper
snd_hda_codec_realtek
video
button
microcode
psmouse
drm
serio_raw
pcspkr
acpi_cpufreq
mperf
snd_hda_codec_hdmi
processor
i2c_algo_bit
lpc_ich
mfd_core
snd_hda_intel
snd_hda_codec
i2c_i801
i2c_core
snd_hwdep
snd_pcm
snd_page_alloc
snd_timer
evdev
snd
soundcore
ext4
crc16
jbd2
mbcache
btrfs
xor
zlib_deflate
raid6_pq
crc32c
libcrc32c
dm_mod
md_mod
sg
sr_mod
cdrom
sd_mod
crc_t10dif
hid_generic
usbhid
hid
ahci
libahci
libata
scsi_mod
ehci_pci
ehci_hcd
xhci_hcd
e1000e
ptp
pps_core
usbcore
usb_common
thermal
fan
thermal_sys
** PCI devices:
00:00.0 Host bridge [0600]: Intel Corporation 4th Gen Core Processor DRAM Controller [8086:0c00] (rev 06)
Subsystem: Intel Corporation Device [8086:204a]
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort+ >SERR- <PERR- INTx-
Latency: 0
Capabilities: <access denied>
00:01.0 PCI bridge [0604]: Intel Corporation Xeon E3-1200 v3/4th Gen Core Processor PCI Express x16 Controller [8086:0c01] (rev 06) (prog-if 00 [Normal decode])
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx+
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0, Cache Line Size: 64 bytes
Bus: primary=00, secondary=01, subordinate=01, sec-latency=0
I/O behind bridge: 0000e000-0000efff
Memory behind bridge: f4000000-f60fffff
Prefetchable memory behind bridge: 00000000e0000000-00000000e7ffffff
Secondary status: 66MHz- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- <SERR- <PERR-
BridgeCtl: Parity- SERR- NoISA- VGA- MAbort- >Reset- FastB2B-
PriDiscTmr- SecDiscTmr- DiscTmrStat- DiscTmrSERREn-
Capabilities: <access denied>
Kernel driver in use: pcieport
00:02.0 VGA compatible controller [0300]: Intel Corporation Xeon E3-1200 v3/4th Gen Core Processor Integrated Graphics Controller [8086:0412] (rev 06) (prog-if 00 [VGA controller])
Subsystem: Intel Corporation Device [8086:204a]
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx+
Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0
Interrupt: pin A routed to IRQ 48
Region 0: Memory at f6400000 (64-bit, non-prefetchable) [size=4M]
Region 2: Memory at d0000000 (64-bit, prefetchable) [size=256M]
Region 4: I/O ports at f000 [size=64]
Expansion ROM at <unassigned> [disabled]
Capabilities: <access denied>
Kernel driver in use: i915
00:03.0 Audio device [0403]: Intel Corporation Xeon E3-1200 v3/4th Gen Core Processor HD Audio Controller [8086:0c0c] (rev 06)
Subsystem: Intel Corporation Device [8086:2010]
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx+
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0, Cache Line Size: 64 bytes
Interrupt: pin A routed to IRQ 46
Region 0: Memory at f6834000 (64-bit, non-prefetchable) [size=16K]
Capabilities: <access denied>
Kernel driver in use: snd_hda_intel
00:14.0 USB controller [0c03]: Intel Corporation 8 Series/C220 Series Chipset Family USB xHCI [8086:8c31] (rev 04) (prog-if 30 [XHCI])
Subsystem: Intel Corporation Device [8086:204a]
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx+
Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0
Interrupt: pin A routed to IRQ 44
Region 0: Memory at f6820000 (64-bit, non-prefetchable) [size=64K]
Capabilities: <access denied>
Kernel driver in use: xhci_hcd
00:16.0 Communication controller [0780]: Intel Corporation 8 Series/C220 Series Chipset Family MEI Controller #1 [8086:8c3a] (rev 04)
Subsystem: Intel Corporation Device [8086:204a]
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx+
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0
Interrupt: pin A routed to IRQ 49
Region 0: Memory at f683f000 (64-bit, non-prefetchable) [size=16]
Capabilities: <access denied>
Kernel driver in use: mei_me
00:19.0 Ethernet controller [0200]: Intel Corporation Ethernet Connection I217-V [8086:153b] (rev 04)
Subsystem: Intel Corporation Device [8086:204a]
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx+
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0
Interrupt: pin A routed to IRQ 43
Region 0: Memory at f6800000 (32-bit, non-prefetchable) [size=128K]
Region 1: Memory at f683d000 (32-bit, non-prefetchable) [size=4K]
Region 2: I/O ports at f080 [size=32]
Capabilities: <access denied>
Kernel driver in use: e1000e
00:1a.0 USB controller [0c03]: Intel Corporation 8 Series/C220 Series Chipset Family USB EHCI #2 [8086:8c2d] (rev 04) (prog-if 20 [EHCI])
Subsystem: Intel Corporation Device [8086:204a]
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0
Interrupt: pin A routed to IRQ 16
Region 0: Memory at f683c000 (32-bit, non-prefetchable) [size=1K]
Capabilities: <access denied>
Kernel driver in use: ehci-pci
00:1b.0 Audio device [0403]: Intel Corporation 8 Series/C220 Series Chipset High Definition Audio Controller [8086:8c20] (rev 04)
Subsystem: Intel Corporation Device [8086:204a]
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx+
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0, Cache Line Size: 64 bytes
Interrupt: pin A routed to IRQ 47
Region 0: Memory at f6830000 (64-bit, non-prefetchable) [size=16K]
Capabilities: <access denied>
Kernel driver in use: snd_hda_intel
00:1d.0 USB controller [0c03]: Intel Corporation 8 Series/C220 Series Chipset Family USB EHCI #1 [8086:8c26] (rev 04) (prog-if 20 [EHCI])
Subsystem: Intel Corporation Device [8086:204a]
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0
Interrupt: pin A routed to IRQ 23
Region 0: Memory at f683b000 (32-bit, non-prefetchable) [size=1K]
Capabilities: <access denied>
Kernel driver in use: ehci-pci
00:1f.0 ISA bridge [0601]: Intel Corporation H87 Express LPC Controller [8086:8c4a] (rev 04)
Subsystem: Intel Corporation Device [8086:204a]
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0
Capabilities: <access denied>
Kernel driver in use: lpc_ich
00:1f.2 SATA controller [0106]: Intel Corporation 8 Series/C220 Series Chipset Family 6-port SATA Controller 1 [AHCI mode] [8086:8c02] (rev 04) (prog-if 01 [AHCI 1.0])
Subsystem: Intel Corporation Device [8086:204a]
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx+
Status: Cap+ 66MHz+ UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0
Interrupt: pin B routed to IRQ 45
Region 0: I/O ports at f0d0 [size=8]
Region 1: I/O ports at f0c0 [size=4]
Region 2: I/O ports at f0b0 [size=8]
Region 3: I/O ports at f0a0 [size=4]
Region 4: I/O ports at f060 [size=32]
Region 5: Memory at f683a000 (32-bit, non-prefetchable) [size=2K]
Capabilities: <access denied>
Kernel driver in use: ahci
00:1f.3 SMBus [0c05]: Intel Corporation 8 Series/C220 Series Chipset Family SMBus Controller [8086:8c22] (rev 04)
Subsystem: Intel Corporation Device [8086:204a]
Control: I/O+ Mem+ BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap- 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Interrupt: pin C routed to IRQ 18
Region 0: Memory at f6839000 (64-bit, non-prefetchable) [size=256]
Region 4: I/O ports at f040 [size=32]
01:00.0 VGA compatible controller [0300]: NVIDIA Corporation GF100GL [Tesla C2050 / C2070] [10de:06d1] (rev a3) (prog-if 00 [VGA controller])
Subsystem: NVIDIA Corporation Tesla C2050 [10de:0771]
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0, Cache Line Size: 64 bytes
Interrupt: pin A routed to IRQ 16
Region 0: Memory at f4000000 (32-bit, non-prefetchable) [size=32M]
Region 1: Memory at e4000000 (64-bit, prefetchable) [size=64M]
Region 3: Memory at e0000000 (64-bit, prefetchable) [size=64M]
Region 5: I/O ports at e000 [size=128]
Expansion ROM at f6000000 [disabled] [size=512K]
Capabilities: <access denied>
Kernel driver in use: nouveau
01:00.1 Audio device [0403]: NVIDIA Corporation GF100 High Definition Audio Controller [10de:0be5] (rev a1)
Subsystem: NVIDIA Corporation Device [10de:0771]
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0, Cache Line Size: 64 bytes
Interrupt: pin B routed to IRQ 17
Region 0: Memory at f6080000 (32-bit, non-prefetchable) [size=16K]
Capabilities: <access denied>
Kernel driver in use: snd_hda_intel
** USB devices:
Bus 004 Device 002: ID 8087:8000 Intel Corp.
Bus 004 Device 001: ID 1d6b:0002 Linux Foundation 2.0 root hub
Bus 003 Device 002: ID 8087:8008 Intel Corp.
Bus 003 Device 001: ID 1d6b:0002 Linux Foundation 2.0 root hub
Bus 002 Device 005: ID 0984:0315 Apricorn
Bus 002 Device 001: ID 1d6b:0003 Linux Foundation 3.0 root hub
Bus 001 Device 003: ID 413c:2105 Dell Computer Corp. Model L100 Keyboard
Bus 001 Device 002: ID 0461:4d17 Primax Electronics, Ltd Optical Mouse
Bus 001 Device 001: ID 1d6b:0002 Linux Foundation 2.0 root hub
-- System Information:
Debian Release: jessie/sid
APT prefers testing
APT policy: (500, 'testing')
Architecture: amd64 (x86_64)
Kernel: Linux 3.10-3-amd64 (SMP w/4 CPU cores)
Locale: LANG=en_US.UTF-8, LC_CTYPE=en_US.UTF-8 (charmap=UTF-8)
Shell: /bin/sh linked to /bin/dash
Versions of packages linux-image-3.10-3-amd64 depends on:
ii debconf [debconf-2.0] 1.5.51
ii initramfs-tools [linux-initramfs-tool] 0.114
ii kmod 9-3
ii linux-base 3.5
ii module-init-tools 9-3
Versions of packages linux-image-3.10-3-amd64 recommends:
ii firmware-linux-free 3.2
Versions of packages linux-image-3.10-3-amd64 suggests:
pn debian-kernel-handbook <none>
ii grub-pc 1.99-27+deb7u1
pn linux-doc-3.10 <none>
Versions of packages linux-image-3.10-3-amd64 is related to:
pn firmware-atheros <none>
pn firmware-bnx2 <none>
pn firmware-bnx2x <none>
pn firmware-brcm80211 <none>
pn firmware-intelwimax <none>
pn firmware-ipw2x00 <none>
pn firmware-ivtv <none>
pn firmware-iwlwifi <none>
pn firmware-libertas <none>
pn firmware-linux <none>
pn firmware-linux-nonfree <none>
pn firmware-myricom <none>
pn firmware-netxen <none>
pn firmware-qlogic <none>
pn firmware-ralink <none>
pn firmware-realtek <none>
pn xen-hypervisor <none>
-- debconf information excluded
--- End Message ---