--- Begin Message ---
- To: Debian Bug Tracking System <submit@bugs.debian.org>
- Subject: linux-image-3.2.0-4-amd64: system becomes unstable, BUG: unable to handle kernel paging request at
- From: Michal Grzedzicki <lazy@iq.pl>
- Date: Thu, 28 Aug 2014 11:42:13 +0200
- Message-id: <20140828094213.16777.95087.reportbug@arttor.iq.pl>
Package: src:linux
Version: 3.2.54-2
Severity: normal
Dear Maintainer,
Aug 27 01:00:01 arttor kernel: [15188695.259636] md: resync of RAID array md1
Aug 27 01:00:01 arttor kernel: [15188695.259638] md: minimum _guaranteed_ speed: 1000 KB/sec/disk.
Aug 27 01:00:01 arttor kernel: [15188695.259639] md: using maximum available idle IO bandwidth (but not more than 200000 KB/sec) for resync.
Aug 27 01:00:01 arttor kernel: [15188695.259642] md: using 128k window, over a total of 8780672k.
Aug 27 01:00:01 arttor kernel: [15188695.259643] md: resuming resync of md1 from checkpoint.
Aug 27 01:00:05 arttor kernel: [15188699.666827] md: md1: resync done.
Aug 27 01:00:05 arttor kernel: [15188699.718541] RAID1 conf printout:
Aug 27 01:00:05 arttor kernel: [15188699.718544] --- wd:2 rd:2
Aug 27 01:00:05 arttor kernel: [15188699.718547] disk 0, wo:0, o:1, dev:sda2
Aug 27 01:00:05 arttor kernel: [15188699.718549] disk 1, wo:0, o:1, dev:sdb2
Aug 27 23:45:21 arttor kernel: [15270349.323948] BUG: unable to handle kernel paging request at ffff8823f444f830
Aug 27 23:45:21 arttor kernel: [15270349.323978] IP: [<ffffffff8110d308>] evict+0x12/0x148
Aug 27 23:45:21 arttor kernel: [15270349.323999] PGD 1606063 PUD 0
Aug 27 23:45:21 arttor kernel: [15270349.324023] Oops: 0000 [#1] SMP
Aug 27 23:45:21 arttor kernel: [15270349.324044] CPU 2
Aug 27 23:45:21 arttor kernel: [15270349.324048] Modules linked in: nfsd nfs nfs_acl auth_rpcgss fscache lockd sunrpc ext3 jbd loop coretemp crc32c_intel ghash_clmulni_intel aesni_intel aes_x86_64 aes_generic snd_pcm snd_page_alloc snd_timer snd soundcore cryptd pcspkr
joydev i2c_i801 i2c_core iTCO_wdt iTCO_vendor_support evdev dcdbas button video processor ext4 crc16 jbd2 mbcache usbhid hid raid1 md_mod sg sd_mod crc_t10dif ahci libahci libata ehci_hcd scsi_mod fan thermal thermal_sys usbcore igb usb_common dca [last unloaded: scsi_w
ait_scan]
Aug 27 23:45:21 arttor kernel: [15270349.324334]
Aug 27 23:45:21 arttor kernel: [15270349.324340] Pid: 46, comm: kswapd0 Not tainted 3.2.0-4-amd64 #1 Debian 3.2.54-2 Dell Inc. PowerEdge C5220/0NVH5D
Aug 27 23:45:21 arttor kernel: [15270349.324387] RIP: 0010:[<ffffffff8110d308>] [<ffffffff8110d308>] evict+0x12/0x148
Aug 27 23:45:21 arttor kernel: [15270349.324413] RSP: 0018:ffff8801f4919c10 EFLAGS: 00010202
Aug 27 23:45:21 arttor kernel: [15270349.324434] RAX: ffff8823f444f800 RBX: ffff8801767c21b0 RCX: ffff8801354aad10
Aug 27 23:45:21 arttor kernel: [15270349.324461] RDX: ffff8801f4919c50 RSI: 0000000000000025 RDI: ffff8801767c21b0
Aug 27 23:45:21 arttor kernel: [15270349.324548] RBP: ffff8801f444f800 R08: 0000000000000025 R09: ffff8801767c2468
Aug 27 23:45:21 arttor kernel: [15270349.324629] R10: 0000000000000000 R11: 0000000000000000 R12: ffff880067a30880
Aug 27 23:45:21 arttor kernel: [15270349.324710] R13: 0000000000000000 R14: ffff8801f444f908 R15: 00000000ffffffff
Aug 27 23:45:21 arttor kernel: [15270349.324793] FS: 0000000000000000(0000) GS:ffff8801ffc80000(0000) knlGS:0000000000000000
Aug 27 23:45:21 arttor kernel: [15270349.324878] CS: 0010 DS: 0000 ES: 0000 CR0: 000000008005003b
Aug 27 23:45:21 arttor kernel: [15270349.324929] CR2: ffff8823f444f830 CR3: 0000000001605000 CR4: 00000000001406e0
Aug 27 23:45:21 arttor kernel: [15270349.325011] DR0: 0000000000000000 DR1: 0000000000000000 DR2: 0000000000000000
Aug 27 23:45:21 arttor kernel: [15270349.325093] DR3: 0000000000000000 DR6: 00000000ffff0ff0 DR7: 0000000000000400
Aug 27 23:45:21 arttor kernel: [15270349.325174] Process kswapd0 (pid: 46, threadinfo ffff8801f4918000, task ffff8801f4915160)
Aug 27 23:45:21 arttor kernel: [15270349.325259] Stack:
Aug 27 23:45:21 arttor kernel: [15270349.325296] ffff8801f4919c50 ffff8801f444f800 ffff880067a30880 ffffffff8110d5f6
Aug 27 23:45:21 arttor kernel: [15270349.325387] ffff880067a30968 ffffffff8110e137 ffff8801f444f900 ffff880067a30900
Aug 27 23:45:21 arttor kernel: [15270349.325477] ffff8801354aad10 ffff880130742968 ffff8801f4919dc0 0000000000000000
Aug 27 23:45:21 arttor kernel: [15270349.325567] Call Trace:
Aug 27 23:45:21 arttor kernel: [15270349.325608] [<ffffffff8110d5f6>] ? dispose_list+0x27/0x31
Aug 27 23:45:21 arttor kernel: [15270349.325659] [<ffffffff8110e137>] ? prune_icache_sb+0x250/0x25f
Aug 27 23:45:21 arttor kernel: [15270349.325713] [<ffffffff810fce2e>] ? prune_super+0xd5/0x13f
Aug 27 23:45:21 arttor kernel: [15270349.325766] [<ffffffff810c24a1>] ? shrink_slab+0x18f/0x24d
Aug 27 23:45:21 arttor kernel: [15270349.325818] [<ffffffff810c4e71>] ? balance_pgdat+0x283/0x4b7
Aug 27 23:45:21 arttor kernel: [15270349.325870] [<ffffffff810c5378>] ? kswapd+0x2d3/0x303
Aug 27 23:45:21 arttor kernel: [15270349.325921] [<ffffffff8105fcd3>] ? add_wait_queue+0x3c/0x3c
Aug 27 23:45:21 arttor kernel: [15270349.325972] [<ffffffff810c50a5>] ? balance_pgdat+0x4b7/0x4b7
Aug 27 23:45:21 arttor kernel: [15270349.326024] [<ffffffff8105f681>] ? kthread+0x76/0x7e
Aug 27 23:45:21 arttor kernel: [15270349.326075] [<ffffffff81356ef4>] ? kernel_thread_helper+0x4/0x10
Aug 27 23:45:21 arttor kernel: [15270349.326128] [<ffffffff8105f60b>] ? kthread_worker_fn+0x139/0x139
Aug 27 23:45:21 arttor kernel: [15270349.326182] [<ffffffff81356ef0>] ? gs_change+0x13/0x13
Aug 27 23:45:21 arttor kernel: [15270349.326230] Code: 00 00 be 07 00 00 00 e8 79 ff ff ff 48 c7 83 98 00 00 00 60 00 00 00 5b c3 41 54 55 53 f6 87 98 00 00 00 20 48 89 fb 48 8b 47 28 <4c> 8b 60 30 75 02 0f 0b 48 8d 87 e8 00 00 00 48 39 87 e8 00 00
Aug 27 23:45:21 arttor kernel: [15270349.326524] RIP [<ffffffff8110d308>] evict+0x12/0x148
Aug 27 23:45:21 arttor kernel: [15270349.326574] RSP <ffff8801f4919c10>
Aug 27 23:45:21 arttor kernel: [15270349.326617] CR2: ffff8823f444f830
Aug 27 23:45:21 arttor kernel: [15270349.327062] ---[ end trace 0035492c301a838d ]---
*** End of the template - remove these lines ***
-- Package-specific info:
** Version:
Linux version 3.2.0-4-amd64 (debian-kernel@lists.debian.org) (gcc version 4.6.3 (Debian 4.6.3-14) ) #1 SMP Debian 3.2.54-2
** Command line:
BOOT_IMAGE=/vmlinuz-3.2.0-4-amd64 root=UUID=5ad5800f-8225-4bc9-a0b7-ab0868ecc494 ro quiet
** Not tainted
** Kernel log:
[ 3.059293] sd 3:0:0:0: [sdb] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
[ 3.060413] sd 2:0:0:0: Attached scsi generic sg0 type 0
[ 3.060456] sd 3:0:0:0: Attached scsi generic sg1 type 0
[ 3.074552] sda: sda1 sda2 sda3
[ 3.074835] sd 2:0:0:0: [sda] Attached SCSI disk
[ 3.076431] sdb: sdb1 sdb2 sdb3
[ 3.076757] sd 3:0:0:0: [sdb] Attached SCSI disk
[ 3.151778] usb 1-1: New USB device found, idVendor=8087, idProduct=0024
[ 3.151781] usb 1-1: New USB device strings: Mfr=0, Product=0, SerialNumber=0
[ 3.152060] hub 1-1:1.0: USB hub found
[ 3.152150] hub 1-1:1.0: 6 ports detected
[ 3.423551] usb 1-1.3: new high-speed USB device number 3 using ehci_hcd
[ 3.532548] usb 1-1.3: New USB device found, idVendor=046b, idProduct=ff01
[ 3.532561] usb 1-1.3: New USB device strings: Mfr=1, Product=2, SerialNumber=3
[ 3.532562] usb 1-1.3: Product: Generic Hub
[ 3.532563] usb 1-1.3: Manufacturer: American Megatrends Inc.
[ 3.532565] usb 1-1.3: SerialNumber: serial
[ 3.533196] hub 1-1.3:1.0: USB hub found
[ 3.533282] hub 1-1.3:1.0: 3 ports detected
[ 3.702753] md: md0 stopped.
[ 3.703270] md: bind<sdb1>
[ 3.703374] md: bind<sda1>
[ 3.704064] md: raid1 personality registered for level 1
[ 3.704219] bio: create slab <bio-1> at 1
[ 3.704260] md/raid1:md0: active with 2 out of 2 mirrors
[ 3.704271] md0: detected capacity change from 0 to 298516480
[ 3.704992] md0: unknown partition table
[ 3.803665] usb 1-1.3.1: new low-speed USB device number 4 using ehci_hcd
[ 3.906632] md: md1 stopped.
[ 3.907126] md: bind<sdb2>
[ 3.907241] md: bind<sda2>
[ 3.907958] md/raid1:md1: not clean -- starting background reconstruction
[ 3.907961] md/raid1:md1: active with 2 out of 2 mirrors
[ 3.907973] md1: detected capacity change from 0 to 8991408128
[ 3.908746] usb 1-1.3.1: New USB device found, idVendor=046b, idProduct=ff10
[ 3.908748] usb 1-1.3.1: New USB device strings: Mfr=1, Product=2, SerialNumber=3
[ 3.908750] usb 1-1.3.1: Product: Virtual Keyboard and Mouse
[ 3.908751] usb 1-1.3.1: Manufacturer: American Megatrends Inc.
[ 3.908752] usb 1-1.3.1: SerialNumber: serial
[ 3.911945] input: American Megatrends Inc. Virtual Keyboard and Mouse as /devices/pci0000:00/0000:00:1d.0/usb1/1-1/1-1.3/1-1.3.1/1-1.3.1:1.0/input/input0
[ 3.911990] generic-usb 0003:046B:FF10.0001: input,hidraw0: USB HID v1.10 Keyboard [American Megatrends Inc. Virtual Keyboard and Mouse] on usb-0000:00:1d.0-1.3.1/input0
[ 3.912558] input: American Megatrends Inc. Virtual Keyboard and Mouse as /devices/pci0000:00/0000:00:1d.0/usb1/1-1/1-1.3/1-1.3.1/1-1.3.1:1.1/input/input1
[ 3.912603] generic-usb 0003:046B:FF10.0002: input,hidraw1: USB HID v1.10 Mouse [American Megatrends Inc. Virtual Keyboard and Mouse] on usb-0000:00:1d.0-1.3.1/input1
[ 3.912611] usbcore: registered new interface driver usbhid
[ 3.912612] usbhid: USB HID core driver
[ 3.914463] md1: unknown partition table
[ 4.110272] md: md2 stopped.
[ 4.110795] md: bind<sdb3>
[ 4.110894] md: bind<sda3>
[ 4.111490] md/raid1:md2: active with 2 out of 2 mirrors
[ 4.111503] md2: detected capacity change from 0 to 490672553984
[ 4.123781] md2: unknown partition table
[ 4.546618] PM: Starting manual resume from disk
[ 4.546620] PM: Hibernation image partition 9:1 present
[ 4.546621] PM: Looking for hibernation image.
[ 4.546762] PM: Image not found (code -22)
[ 4.546764] PM: Hibernation image not present or could not be loaded.
[ 4.554393] EXT4-fs (md2): INFO: recovery required on readonly filesystem
[ 4.554395] EXT4-fs (md2): write access will be enabled during recovery
[ 6.403438] EXT4-fs (md2): recovery complete
[ 6.403887] EXT4-fs (md2): mounted filesystem with ordered data mode. Opts: (null)
[ 7.998971] udevd[416]: starting version 175
[ 8.165828] ACPI: resource 0000:00:1f.3 [io 0xf000-0xf01f] conflicts with ACPI region SMBI [io 0xf000-0xf00f]
[ 8.165831] ACPI: If an ACPI driver is available for this device, you should use it instead of the native driver
[ 8.222760] input: PC Speaker as /devices/platform/pcspkr/input/input2
[ 8.231286] dcdbas dcdbas: Dell Systems Management Base Driver (version 5.6.0-3.2)
[ 8.234841] input: Power Button as /devices/LNXSYSTM:00/LNXSYBUS:00/PNP0C0C:00/input/input3
[ 8.234869] ACPI: Power Button [PWRB]
[ 8.234906] input: Power Button as /devices/LNXSYSTM:00/LNXPWRBN:00/input/input4
[ 8.234932] ACPI: Power Button [PWRF]
[ 8.284771] alg: No test for __gcm-aes-aesni (__driver-gcm-aes-aesni)
[ 8.380934] iTCO_vendor_support: vendor-support=0
[ 8.381449] iTCO_wdt: Intel TCO WatchDog Timer Driver v1.07
[ 8.381508] iTCO_wdt: unable to reset NO_REBOOT flag, device disabled by hardware/BIOS
[ 8.606045] Error: Driver 'pcspkr' is already registered, aborting...
[ 9.448465] Adding 8780664k swap on /dev/md1. Priority:-1 extents:1 across:8780664k
[ 9.466892] EXT4-fs (md2): re-mounted. Opts: (null)
[ 9.801917] EXT4-fs (md2): re-mounted. Opts: errors=remount-ro
[ 9.915275] loop: module loaded
[ 10.522087] kjournald starting. Commit interval 5 seconds
[ 10.527397] EXT3-fs (md0): using internal journal
[ 10.527400] EXT3-fs (md0): mounted filesystem with ordered data mode
[ 11.477223] RPC: Registered named UNIX socket transport module.
[ 11.477225] RPC: Registered udp transport module.
[ 11.477227] RPC: Registered tcp transport module.
[ 11.477228] RPC: Registered tcp NFSv4.1 backchannel transport module.
[ 11.491409] FS-Cache: Loaded
[ 11.530853] FS-Cache: Netfs 'nfs' registered for caching
[ 11.540623] Installing knfsd (copyright (C) 1996 okir@monad.swb.de).
[ 11.614602] igb: eth0 NIC Link is Up 1000 Mbps Full Duplex, Flow Control: RX/TX
[ 21.982957] eth0: no IPv6 routers present
[ 7235.842079] md: resync of RAID array md1
[ 7235.842082] md: minimum _guaranteed_ speed: 1000 KB/sec/disk.
[ 7235.842083] md: using maximum available idle IO bandwidth (but not more than 200000 KB/sec) for resync.
[ 7235.842086] md: using 128k window, over a total of 8780672k.
[ 7379.493012] md: md1: resync done.
[ 7379.653257] RAID1 conf printout:
[ 7379.653259] --- wd:2 rd:2
[ 7379.653261] disk 0, wo:0, o:1, dev:sda2
[ 7379.653262] disk 1, wo:0, o:1, dev:sdb2
** Model information
sys_vendor: Dell Inc.
product_name: PowerEdge C5220
product_version: A00
chassis_vendor: Dell Inc.
chassis_version: N/A
bios_vendor: Dell Inc.
bios_version: 2.0.3
board_vendor: Dell Inc.
board_name: 0NVH5D
board_version: A00
** Loaded modules:
nfsd
nfs
nfs_acl
auth_rpcgss
fscache
lockd
sunrpc
ext3
jbd
loop
snd_pcm
snd_page_alloc
snd_timer
coretemp
crc32c_intel
snd
ghash_clmulni_intel
iTCO_wdt
iTCO_vendor_support
aesni_intel
aes_x86_64
aes_generic
cryptd
soundcore
video
processor
button
dcdbas
pcspkr
joydev
i2c_i801
i2c_core
evdev
ext4
crc16
jbd2
mbcache
usbhid
hid
raid1
md_mod
sg
sd_mod
crc_t10dif
ahci
libahci
fan
thermal
libata
thermal_sys
scsi_mod
ehci_hcd
usbcore
igb
dca
usb_common
** PCI devices:
00:00.0 Host bridge [0600]: Intel Corporation Xeon E3-1200 v2/Ivy Bridge DRAM Controller [8086:0158] (rev 09)
Subsystem: Dell Device [1028:0501]
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr+ Stepping- SERR+ FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort+ >SERR- <PERR- INTx-
Latency: 0
Capabilities: [e0] Vendor Specific Information: Len=0c <?>
00:01.0 PCI bridge [0604]: Intel Corporation Xeon E3-1200 v2/3rd Gen Core processor PCI Express Root Port [8086:0151] (rev 09) (prog-if 00 [Normal decode])
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr+ Stepping- SERR+ FastB2B- DisINTx+
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0, Cache Line Size: 64 bytes
Bus: primary=00, secondary=01, subordinate=01, sec-latency=0
Secondary status: 66MHz- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- <SERR- <PERR-
BridgeCtl: Parity+ SERR+ NoISA- VGA- MAbort- >Reset- FastB2B-
PriDiscTmr- SecDiscTmr- DiscTmrStat- DiscTmrSERREn-
Capabilities: [88] Subsystem: Dell Device [1028:0501]
Capabilities: [80] Power Management version 3
Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA PME(D0+,D1-,D2-,D3hot+,D3cold+)
Status: D0 NoSoftRst+ PME-Enable- DSel=0 DScale=0 PME-
Capabilities: [90] MSI: Enable+ Count=1/1 Maskable- 64bit-
Address: feeff00c Data: 4149
Capabilities: [a0] Express (v2) Root Port (Slot+), MSI 00
DevCap: MaxPayload 256 bytes, PhantFunc 0, Latency L0s <64ns, L1 <1us
ExtTag- RBE+ FLReset-
DevCtl: Report errors: Correctable+ Non-Fatal+ Fatal+ Unsupported+
RlxdOrd- ExtTag- PhantFunc- AuxPwr- NoSnoop-
MaxPayload 256 bytes, MaxReadReq 128 bytes
DevSta: CorrErr- UncorrErr- FatalErr- UnsuppReq- AuxPwr- TransPend-
LnkCap: Port #2, Speed 8GT/s, Width x8, ASPM L0s L1, Latency L0 <1us, L1 <8us
ClockPM- Surprise- LLActRep- BwNot+
LnkCtl: ASPM Disabled; RCB 64 bytes Disabled- Retrain- CommClk-
ExtSynch- ClockPM- AutWidDis- BWInt- AutBWInt-
LnkSta: Speed 2.5GT/s, Width x0, TrErr- Train- SlotClk+ DLActive- BWMgmt- ABWMgmt-
SltCap: AttnBtn- PwrCtrl- MRL- AttnInd- PwrInd- HotPlug- Surprise-
Slot #1, PowerLimit 75.000W; Interlock- NoCompl+
SltCtl: Enable: AttnBtn- PwrFlt- MRL- PresDet- CmdCplt- HPIrq- LinkChg-
Control: AttnInd Unknown, PwrInd Unknown, Power- Interlock-
SltSta: Status: AttnBtn- PowerFlt- MRL- CmdCplt- PresDet- Interlock-
Changed: MRL- PresDet- LinkState-
RootCtl: ErrCorrectable- ErrNon-Fatal- ErrFatal+ PMEIntEna- CRSVisible-
RootCap: CRSVisible-
RootSta: PME ReqID 0000, PMEStatus- PMEPending-
DevCap2: Completion Timeout: Not Supported, TimeoutDis- ARIFwd-
DevCtl2: Completion Timeout: 50us to 50ms, TimeoutDis- ARIFwd-
LnkCtl2: Target Link Speed: 8GT/s, EnterCompliance- SpeedDis-, Selectable De-emphasis: -3.5dB
Transmit Margin: Normal Operating Range, EnterModifiedCompliance- ComplianceSOS-
Compliance De-emphasis: -6dB
LnkSta2: Current De-emphasis Level: -6dB, EqualizationComplete-, EqualizationPhase1-
EqualizationPhase2-, EqualizationPhase3-, LinkEqualizationRequest-
Capabilities: [100 v1] Virtual Channel
Caps: LPEVC=0 RefClk=100ns PATEntryBits=1
Arb: Fixed- WRR32- WRR64- WRR128-
Ctrl: ArbSelect=Fixed
Status: InProgress-
VC0: Caps: PATOffset=00 MaxTimeSlots=1 RejSnoopTrans-
Arb: Fixed+ WRR32- WRR64- WRR128- TWRR128- WRR256-
Ctrl: Enable+ ID=0 ArbSelect=Fixed TC/VC=ff
Status: NegoPending- InProgress-
Capabilities: [140 v1] Root Complex Link
Desc: PortNumber=02 ComponentID=01 EltType=Config
Link0: Desc: TargetPort=00 TargetComponent=01 AssocRCRB- LinkType=MemMapped LinkValid+
Addr: 00000000fed19000
Capabilities: [d94 v1] #19
Kernel driver in use: pcieport
00:01.1 PCI bridge [0604]: Intel Corporation Xeon E3-1200 v2/3rd Gen Core processor PCI Express Root Port [8086:0155] (rev 09) (prog-if 00 [Normal decode])
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr+ Stepping- SERR+ FastB2B- DisINTx+
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0, Cache Line Size: 64 bytes
Bus: primary=00, secondary=02, subordinate=02, sec-latency=0
I/O behind bridge: 0000e000-0000efff
Memory behind bridge: df900000-dfafffff
Secondary status: 66MHz- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- <SERR- <PERR-
BridgeCtl: Parity+ SERR+ NoISA- VGA- MAbort- >Reset- FastB2B-
PriDiscTmr- SecDiscTmr- DiscTmrStat- DiscTmrSERREn-
Capabilities: [88] Subsystem: Dell Device [1028:0501]
Capabilities: [80] Power Management version 3
Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA PME(D0+,D1-,D2-,D3hot+,D3cold+)
Status: D0 NoSoftRst+ PME-Enable- DSel=0 DScale=0 PME-
Capabilities: [90] MSI: Enable+ Count=1/1 Maskable- 64bit-
Address: feeff00c Data: 4151
Capabilities: [a0] Express (v2) Root Port (Slot+), MSI 00
DevCap: MaxPayload 128 bytes, PhantFunc 0, Latency L0s <64ns, L1 <1us
ExtTag- RBE+ FLReset-
DevCtl: Report errors: Correctable+ Non-Fatal+ Fatal+ Unsupported+
RlxdOrd- ExtTag- PhantFunc- AuxPwr- NoSnoop-
MaxPayload 128 bytes, MaxReadReq 128 bytes
DevSta: CorrErr- UncorrErr- FatalErr- UnsuppReq- AuxPwr- TransPend-
LnkCap: Port #3, Speed 8GT/s, Width x4, ASPM L0s L1, Latency L0 <256ns, L1 <8us
ClockPM- Surprise- LLActRep- BwNot+
LnkCtl: ASPM Disabled; RCB 64 bytes Disabled- Retrain- CommClk+
ExtSynch- ClockPM- AutWidDis- BWInt- AutBWInt-
LnkSta: Speed 5GT/s, Width x4, TrErr- Train- SlotClk+ DLActive- BWMgmt+ ABWMgmt+
SltCap: AttnBtn- PwrCtrl- MRL- AttnInd- PwrInd- HotPlug- Surprise-
Slot #2, PowerLimit 75.000W; Interlock- NoCompl+
SltCtl: Enable: AttnBtn- PwrFlt- MRL- PresDet- CmdCplt- HPIrq- LinkChg-
Control: AttnInd Unknown, PwrInd Unknown, Power- Interlock-
SltSta: Status: AttnBtn- PowerFlt- MRL- CmdCplt- PresDet+ Interlock-
Changed: MRL- PresDet+ LinkState-
RootCtl: ErrCorrectable- ErrNon-Fatal- ErrFatal+ PMEIntEna- CRSVisible-
RootCap: CRSVisible-
RootSta: PME ReqID 0000, PMEStatus- PMEPending-
DevCap2: Completion Timeout: Not Supported, TimeoutDis- ARIFwd-
DevCtl2: Completion Timeout: 50us to 50ms, TimeoutDis- ARIFwd-
LnkCtl2: Target Link Speed: 8GT/s, EnterCompliance- SpeedDis-, Selectable De-emphasis: -3.5dB
Transmit Margin: Normal Operating Range, EnterModifiedCompliance- ComplianceSOS-
Compliance De-emphasis: -6dB
LnkSta2: Current De-emphasis Level: -3.5dB, EqualizationComplete-, EqualizationPhase1-
EqualizationPhase2-, EqualizationPhase3-, LinkEqualizationRequest-
Capabilities: [100 v1] Virtual Channel
Caps: LPEVC=0 RefClk=100ns PATEntryBits=1
Arb: Fixed- WRR32- WRR64- WRR128-
Ctrl: ArbSelect=Fixed
Status: InProgress-
VC0: Caps: PATOffset=00 MaxTimeSlots=1 RejSnoopTrans-
Arb: Fixed+ WRR32- WRR64- WRR128- TWRR128- WRR256-
Ctrl: Enable+ ID=0 ArbSelect=Fixed TC/VC=ff
Status: NegoPending- InProgress-
Capabilities: [140 v1] Root Complex Link
Desc: PortNumber=03 ComponentID=01 EltType=Config
Link0: Desc: TargetPort=00 TargetComponent=01 AssocRCRB- LinkType=MemMapped LinkValid+
Addr: 00000000fed19000
Capabilities: [d94 v1] #19
Kernel driver in use: pcieport
00:16.0 Communication controller [0780]: Intel Corporation 6 Series/C200 Series Chipset Family MEI Controller #1 [8086:1c3a] (rev 04)
Subsystem: Dell Device [1028:0501]
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0
Interrupt: pin A routed to IRQ 11
Region 0: Memory at dfb07000 (64-bit, non-prefetchable) [size=16]
Capabilities: [50] Power Management version 3
Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA PME(D0+,D1-,D2-,D3hot+,D3cold+)
Status: D0 NoSoftRst+ PME-Enable- DSel=0 DScale=0 PME-
Capabilities: [8c] MSI: Enable- Count=1/1 Maskable- 64bit+
Address: 0000000000000000 Data: 0000
00:16.1 Communication controller [0780]: Intel Corporation 6 Series/C200 Series Chipset Family MEI Controller #2 [8086:1c3b] (rev 04)
Subsystem: Dell Device [1028:0501]
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0
Interrupt: pin B routed to IRQ 11
Region 0: Memory at dfb06000 (64-bit, non-prefetchable) [size=16]
Capabilities: [50] Power Management version 3
Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA PME(D0+,D1-,D2-,D3hot+,D3cold+)
Status: D0 NoSoftRst+ PME-Enable- DSel=0 DScale=0 PME-
Capabilities: [8c] MSI: Enable- Count=1/1 Maskable- 64bit+
Address: 0000000000000000 Data: 0000
00:1d.0 USB controller [0c03]: Intel Corporation 6 Series/C200 Series Chipset Family USB Enhanced Host Controller #1 [8086:1c26] (rev 05) (prog-if 20 [EHCI])
Subsystem: Dell Device [1028:0501]
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr+ Stepping- SERR+ FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0
Interrupt: pin A routed to IRQ 23
Region 0: Memory at dfb03000 (32-bit, non-prefetchable) [size=1K]
Capabilities: [50] Power Management version 2
Flags: PMEClk- DSI- D1- D2- AuxCurrent=375mA PME(D0+,D1-,D2-,D3hot+,D3cold+)
Status: D0 NoSoftRst- PME-Enable- DSel=0 DScale=0 PME-
Capabilities: [58] Debug port: BAR=1 offset=00a0
Capabilities: [98] PCI Advanced Features
AFCap: TP+ FLR+
AFCtrl: FLR-
AFStatus: TP-
Kernel driver in use: ehci_hcd
00:1e.0 PCI bridge [0604]: Intel Corporation 82801 PCI Bridge [8086:244e] (rev a5) (prog-if 01 [Subtractive decode])
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr+ Stepping- SERR+ FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0
Bus: primary=00, secondary=03, subordinate=03, sec-latency=32
I/O behind bridge: 0000d000-0000dfff
Memory behind bridge: df000000-df8fffff
Secondary status: 66MHz- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort+ <SERR- <PERR-
BridgeCtl: Parity+ SERR+ NoISA- VGA+ MAbort- >Reset- FastB2B-
PriDiscTmr- SecDiscTmr- DiscTmrStat- DiscTmrSERREn-
Capabilities: [50] Subsystem: Dell Device [1028:0501]
00:1f.0 ISA bridge [0601]: Intel Corporation C204 Chipset Family LPC Controller [8086:1c54] (rev 05)
Subsystem: Dell Device [1028:0501]
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr+ Stepping- SERR+ FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0
Capabilities: [e0] Vendor Specific Information: Len=0c <?>
00:1f.2 SATA controller [0106]: Intel Corporation 6 Series/C200 Series Chipset Family SATA AHCI Controller [8086:1c02] (rev 05) (prog-if 01 [AHCI 1.0])
Subsystem: Dell Device [1028:0501]
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr+ Stepping- SERR- FastB2B- DisINTx+
Status: Cap+ 66MHz+ UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0
Interrupt: pin B routed to IRQ 51
Region 0: I/O ports at f070 [size=8]
Region 1: I/O ports at f060 [size=4]
Region 2: I/O ports at f050 [size=8]
Region 3: I/O ports at f040 [size=4]
Region 4: I/O ports at f020 [size=32]
Region 5: Memory at dfb02000 (32-bit, non-prefetchable) [size=2K]
Capabilities: [80] MSI: Enable+ Count=1/1 Maskable- 64bit-
Address: feeff00c Data: 41b1
Capabilities: [70] Power Management version 3
Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA PME(D0-,D1-,D2-,D3hot+,D3cold-)
Status: D0 NoSoftRst+ PME-Enable- DSel=0 DScale=0 PME-
Capabilities: [a8] SATA HBA v1.0 BAR4 Offset=00000004
Capabilities: [b0] PCI Advanced Features
AFCap: TP+ FLR+
AFCtrl: FLR-
AFStatus: TP-
Kernel driver in use: ahci
00:1f.3 SMBus [0c05]: Intel Corporation 6 Series/C200 Series Chipset Family SMBus Controller [8086:1c22] (rev 05)
Subsystem: Dell Device [1028:0501]
Control: I/O+ Mem+ BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr+ Stepping- SERR+ FastB2B- DisINTx-
Status: Cap- 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Interrupt: pin C routed to IRQ 18
Region 0: Memory at dfb01000 (64-bit, non-prefetchable) [size=256]
Region 4: I/O ports at f000 [size=32]
02:00.0 Ethernet controller [0200]: Intel Corporation 82580 Gigabit Network Connection [8086:150e] (rev 01)
Subsystem: Dell Device [1028:0501]
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr+ Stepping- SERR+ FastB2B- DisINTx+
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0, Cache Line Size: 64 bytes
Interrupt: pin A routed to IRQ 17
Region 0: Memory at df980000 (32-bit, non-prefetchable) [size=512K]
Region 2: I/O ports at e020 [size=32]
Region 3: Memory at dfa04000 (32-bit, non-prefetchable) [size=16K]
Capabilities: [40] Power Management version 3
Flags: PMEClk- DSI+ D1- D2- AuxCurrent=0mA PME(D0+,D1-,D2-,D3hot+,D3cold+)
Status: D0 NoSoftRst- PME-Enable- DSel=0 DScale=1 PME-
Capabilities: [50] MSI: Enable- Count=1/1 Maskable+ 64bit+
Address: 0000000000000000 Data: 0000
Masking: 00000000 Pending: 00000000
Capabilities: [70] MSI-X: Enable+ Count=10 Masked-
Vector table: BAR=3 offset=00000000
PBA: BAR=3 offset=00002000
Capabilities: [a0] Express (v2) Endpoint, MSI 00
DevCap: MaxPayload 512 bytes, PhantFunc 0, Latency L0s <512ns, L1 <64us
ExtTag- AttnBtn- AttnInd- PwrInd- RBE+ FLReset+
DevCtl: Report errors: Correctable+ Non-Fatal+ Fatal+ Unsupported+
RlxdOrd- ExtTag- PhantFunc- AuxPwr- NoSnoop+ FLReset-
MaxPayload 128 bytes, MaxReadReq 512 bytes
DevSta: CorrErr+ UncorrErr- FatalErr- UnsuppReq+ AuxPwr+ TransPend-
LnkCap: Port #1, Speed 5GT/s, Width x4, ASPM L0s L1, Latency L0 <4us, L1 <8us
ClockPM- Surprise- LLActRep- BwNot-
LnkCtl: ASPM Disabled; RCB 64 bytes Disabled- Retrain- CommClk+
ExtSynch- ClockPM- AutWidDis- BWInt- AutBWInt-
LnkSta: Speed 5GT/s, Width x4, TrErr- Train- SlotClk+ DLActive- BWMgmt- ABWMgmt-
DevCap2: Completion Timeout: Range ABCD, TimeoutDis+
DevCtl2: Completion Timeout: 50us to 50ms, TimeoutDis-
LnkCtl2: Target Link Speed: 5GT/s, EnterCompliance- SpeedDis-, Selectable De-emphasis: -6dB
Transmit Margin: Normal Operating Range, EnterModifiedCompliance- ComplianceSOS-
Compliance De-emphasis: -6dB
LnkSta2: Current De-emphasis Level: -3.5dB, EqualizationComplete-, EqualizationPhase1-
EqualizationPhase2-, EqualizationPhase3-, LinkEqualizationRequest-
Capabilities: [100 v1] Advanced Error Reporting
UESta: DLP- SDES- TLP- FCP- CmpltTO- CmpltAbrt- UnxCmplt- RxOF- MalfTLP- ECRC- UnsupReq- ACSViol-
UEMsk: DLP- SDES- TLP- FCP- CmpltTO- CmpltAbrt- UnxCmplt- RxOF- MalfTLP- ECRC- UnsupReq+ ACSViol-
UESvrt: DLP+ SDES+ TLP- FCP+ CmpltTO- CmpltAbrt- UnxCmplt- RxOF+ MalfTLP+ ECRC- UnsupReq- ACSViol-
CESta: RxErr- BadTLP- BadDLLP- Rollover- Timeout- NonFatalErr+
CEMsk: RxErr+ BadTLP+ BadDLLP+ Rollover+ Timeout+ NonFatalErr+
AERCap: First Error Pointer: 00, GenCap+ CGenEn- ChkCap+ ChkEn-
Capabilities: [140 v1] Device Serial Number 04-7d-7b-ff-ff-fc-dd-50
Capabilities: [1a0 v1] Transaction Processing Hints
Device specific mode supported
Steering table in TPH capability structure
Capabilities: [1c0 v1] Latency Tolerance Reporting
Max snoop latency: 0ns
Max no snoop latency: 0ns
Kernel driver in use: igb
02:00.1 Ethernet controller [0200]: Intel Corporation 82580 Gigabit Network Connection [8086:150e] (rev 01)
Subsystem: Dell Device [1028:0501]
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr+ Stepping- SERR+ FastB2B- DisINTx+
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0, Cache Line Size: 64 bytes
Interrupt: pin B routed to IRQ 18
Region 0: Memory at df900000 (32-bit, non-prefetchable) [size=512K]
Region 2: I/O ports at e000 [size=32]
Region 3: Memory at dfa00000 (32-bit, non-prefetchable) [size=16K]
Capabilities: [40] Power Management version 3
Flags: PMEClk- DSI+ D1- D2- AuxCurrent=0mA PME(D0+,D1-,D2-,D3hot+,D3cold+)
Status: D0 NoSoftRst- PME-Enable- DSel=0 DScale=1 PME-
Capabilities: [50] MSI: Enable- Count=1/1 Maskable+ 64bit+
Address: 0000000000000000 Data: 0000
Masking: 00000000 Pending: 00000000
Capabilities: [70] MSI-X: Enable+ Count=10 Masked-
Vector table: BAR=3 offset=00000000
PBA: BAR=3 offset=00002000
Capabilities: [a0] Express (v2) Endpoint, MSI 00
DevCap: MaxPayload 512 bytes, PhantFunc 0, Latency L0s <512ns, L1 <64us
ExtTag- AttnBtn- AttnInd- PwrInd- RBE+ FLReset+
DevCtl: Report errors: Correctable+ Non-Fatal+ Fatal+ Unsupported+
RlxdOrd- ExtTag- PhantFunc- AuxPwr- NoSnoop+ FLReset-
MaxPayload 128 bytes, MaxReadReq 512 bytes
DevSta: CorrErr+ UncorrErr- FatalErr- UnsuppReq+ AuxPwr+ TransPend-
LnkCap: Port #1, Speed 5GT/s, Width x4, ASPM L0s L1, Latency L0 <4us, L1 <8us
ClockPM- Surprise- LLActRep- BwNot-
LnkCtl: ASPM Disabled; RCB 64 bytes Disabled- Retrain- CommClk+
ExtSynch- ClockPM- AutWidDis- BWInt- AutBWInt-
LnkSta: Speed 5GT/s, Width x4, TrErr- Train- SlotClk+ DLActive- BWMgmt- ABWMgmt-
DevCap2: Completion Timeout: Range ABCD, TimeoutDis+
DevCtl2: Completion Timeout: 50us to 50ms, TimeoutDis-
LnkCtl2: Target Link Speed: 2.5GT/s, EnterCompliance- SpeedDis-, Selectable De-emphasis: -6dB
Transmit Margin: Normal Operating Range, EnterModifiedCompliance- ComplianceSOS-
Compliance De-emphasis: -6dB
LnkSta2: Current De-emphasis Level: -6dB, EqualizationComplete-, EqualizationPhase1-
EqualizationPhase2-, EqualizationPhase3-, LinkEqualizationRequest-
Capabilities: [100 v1] Advanced Error Reporting
UESta: DLP- SDES- TLP- FCP- CmpltTO- CmpltAbrt- UnxCmplt- RxOF- MalfTLP- ECRC- UnsupReq- ACSViol-
UEMsk: DLP- SDES- TLP- FCP- CmpltTO- CmpltAbrt- UnxCmplt- RxOF- MalfTLP- ECRC- UnsupReq+ ACSViol-
UESvrt: DLP+ SDES+ TLP- FCP+ CmpltTO- CmpltAbrt- UnxCmplt- RxOF+ MalfTLP+ ECRC- UnsupReq- ACSViol-
CESta: RxErr- BadTLP- BadDLLP- Rollover- Timeout- NonFatalErr+
CEMsk: RxErr+ BadTLP+ BadDLLP+ Rollover+ Timeout+ NonFatalErr+
AERCap: First Error Pointer: 00, GenCap+ CGenEn- ChkCap+ ChkEn-
Capabilities: [140 v1] Device Serial Number 04-7d-7b-ff-ff-fc-dd-50
Capabilities: [1a0 v1] Transaction Processing Hints
Device specific mode supported
Steering table in TPH capability structure
Kernel driver in use: igb
03:0b.0 VGA compatible controller [0300]: ASPEED Technology, Inc. ASPEED Graphics Family [1a03:2000] (rev 10) (prog-if 00 [VGA controller])
Subsystem: Dell Device [1028:0501]
Control: I/O+ Mem+ BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Interrupt: pin A routed to IRQ 11
Region 0: Memory at df000000 (32-bit, non-prefetchable) [size=8M]
Region 1: Memory at df800000 (32-bit, non-prefetchable) [size=128K]
Region 2: I/O ports at d000 [size=128]
Expansion ROM at <unassigned> [disabled]
Capabilities: [40] Power Management version 3
Flags: PMEClk- DSI- D1+ D2+ AuxCurrent=375mA PME(D0+,D1+,D2+,D3hot+,D3cold+)
Status: D0 NoSoftRst- PME-Enable- DSel=0 DScale=0 PME-
** USB devices:
Bus 001 Device 001: ID 1d6b:0002 Linux Foundation 2.0 root hub
Bus 001 Device 002: ID 8087:0024 Intel Corp. Integrated Rate Matching Hub
Bus 001 Device 003: ID 046b:ff01 American Megatrends, Inc.
Bus 001 Device 004: ID 046b:ff10 American Megatrends, Inc. Virtual Keyboard and Mouse
-- System Information:
Debian Release: 7.4
APT prefers stable-updates
APT policy: (500, 'stable-updates'), (500, 'stable')
Architecture: amd64 (x86_64)
Kernel: Linux 3.2.0-4-amd64 (SMP w/8 CPU cores)
Locale: LANG=en_US.UTF-8, LC_CTYPE=en_US.UTF-8 (charmap=UTF-8)
Shell: /bin/sh linked to /bin/dash
Versions of packages linux-image-3.2.0-4-amd64 depends on:
ii debconf [debconf-2.0] 1.5.49
ii initramfs-tools [linux-initramfs-tool] 0.109.1
ii kmod 9-3
ii linux-base 3.5
ii module-init-tools 9-3
Versions of packages linux-image-3.2.0-4-amd64 recommends:
pn firmware-linux-free <none>
Versions of packages linux-image-3.2.0-4-amd64 suggests:
pn debian-kernel-handbook <none>
ii grub-pc 1.99-27+deb7u2
pn linux-doc-3.2 <none>
Versions of packages linux-image-3.2.0-4-amd64 is related to:
pn firmware-atheros <none>
pn firmware-bnx2 <none>
pn firmware-bnx2x <none>
pn firmware-brcm80211 <none>
pn firmware-intelwimax <none>
pn firmware-ipw2x00 <none>
pn firmware-ivtv <none>
pn firmware-iwlwifi <none>
pn firmware-libertas <none>
pn firmware-linux <none>
pn firmware-linux-nonfree <none>
pn firmware-myricom <none>
pn firmware-netxen <none>
pn firmware-qlogic <none>
pn firmware-ralink <none>
pn firmware-realtek <none>
pn xen-hypervisor <none>
-- debconf information:
linux-image-3.2.0-4-amd64/postinst/depmod-error-initrd-3.2.0-4-amd64: false
linux-image-3.2.0-4-amd64/prerm/removing-running-kernel-3.2.0-4-amd64: true
linux-image-3.2.0-4-amd64/postinst/ignoring-ramdisk:
linux-image-3.2.0-4-amd64/postinst/missing-firmware-3.2.0-4-amd64:
--- End Message ---