--- Begin Message ---
- To: Debian Bug Tracking System <submit@bugs.debian.org>
- Subject: linux-image-3.11-1-amd64: Wireless toggle hotkey works or not depending on wireless state during boot
- From: Mikolaj Menke <miki@menek.one.pl>
- Date: Wed, 13 Nov 2013 19:42:56 +0100
- Message-id: <20131113184256.8953.2347.reportbug@eee>
Package: src:linux
Version: 3.11.6-2
Severity: normal
Wifi toggle hotkey works when system boots with wifi on, but the wifi LED does
not show the real status, it always stays on. If the system boots with wifi off
the hotkey does not work and the LED stays off. This occurs with linux-image
3.10 and 3.11. It used to work fine with 3.5.
-- Package-specific info:
** Kernel log: boot messages should be attached
** Model information
sys_vendor: ASUSTeK Computer INC.
product_name: 1015PE
product_version: x.x
chassis_vendor: ASUSTeK Computer INC.
chassis_version: x.x
bios_vendor: American Megatrends Inc.
bios_version: 1301
board_vendor: ASUSTeK Computer INC.
board_name: 1015PE
board_version: x.xx
** Network interface configuration:
# This file describes the network interfaces available on your system
# and how to activate them. For more information, see interfaces(5).
# The loopback network interface
auto lo
iface lo inet loopback
# The primary network interface
allow-hotplug eth0
#NetworkManager#iface eth0 inet dhcp
** PCI devices:
00:00.0 Host bridge [0600]: Intel Corporation Atom Processor D4xx/D5xx/N4xx/N5xx DMI Bridge [8086:a010]
Subsystem: ASUSTeK Computer Inc. Device [1043:83ac]
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort+ >SERR- <PERR- INTx-
Latency: 0
Capabilities: <access denied>
Kernel driver in use: agpgart-intel
00:02.0 VGA compatible controller [0300]: Intel Corporation Atom Processor D4xx/D5xx/N4xx/N5xx Integrated Graphics Controller [8086:a011] (prog-if 00 [VGA controller])
Subsystem: ASUSTeK Computer Inc. Device [1043:83ac]
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx+
Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0
Interrupt: pin A routed to IRQ 44
Region 0: Memory at f7e00000 (32-bit, non-prefetchable) [size=512K]
Region 1: I/O ports at dc00 [size=8]
Region 2: Memory at d0000000 (32-bit, prefetchable) [size=256M]
Region 3: Memory at f7d00000 (32-bit, non-prefetchable) [size=1M]
Expansion ROM at <unassigned> [disabled]
Capabilities: <access denied>
Kernel driver in use: i915
00:02.1 Display controller [0380]: Intel Corporation Atom Processor D4xx/D5xx/N4xx/N5xx Integrated Graphics Controller [8086:a012]
Subsystem: ASUSTeK Computer Inc. Device [1043:83ac]
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0
Region 0: Memory at f7e80000 (32-bit, non-prefetchable) [size=512K]
Capabilities: <access denied>
00:1b.0 Audio device [0403]: Intel Corporation NM10/ICH7 Family High Definition Audio Controller [8086:27d8] (rev 02)
Subsystem: ASUSTeK Computer Inc. Device [1043:841c]
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx+
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0, Cache Line Size: 32 bytes
Interrupt: pin A routed to IRQ 45
Region 0: Memory at f7cf8000 (64-bit, non-prefetchable) [size=16K]
Capabilities: <access denied>
Kernel driver in use: snd_hda_intel
00:1c.0 PCI bridge [0604]: Intel Corporation NM10/ICH7 Family PCI Express Port 1 [8086:27d0] (rev 02) (prog-if 00 [Normal decode])
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR+ FastB2B- DisINTx+
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0, Cache Line Size: 32 bytes
Bus: primary=00, secondary=04, subordinate=04, sec-latency=0
I/O behind bridge: 00001000-00001fff
Memory behind bridge: 80000000-801fffff
Prefetchable memory behind bridge: 0000000080200000-00000000803fffff
Secondary status: 66MHz- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- <SERR- <PERR-
BridgeCtl: Parity- SERR+ NoISA- VGA- MAbort- >Reset- FastB2B-
PriDiscTmr- SecDiscTmr- DiscTmrStat- DiscTmrSERREn-
Capabilities: <access denied>
Kernel driver in use: pcieport
00:1c.1 PCI bridge [0604]: Intel Corporation NM10/ICH7 Family PCI Express Port 2 [8086:27d2] (rev 02) (prog-if 00 [Normal decode])
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR+ FastB2B- DisINTx+
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0, Cache Line Size: 32 bytes
Bus: primary=00, secondary=02, subordinate=03, sec-latency=0
I/O behind bridge: 00002000-00002fff
Memory behind bridge: f8000000-fbffffff
Prefetchable memory behind bridge: 00000000f0000000-00000000f6ffffff
Secondary status: 66MHz- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- <SERR- <PERR-
BridgeCtl: Parity- SERR+ NoISA- VGA- MAbort- >Reset- FastB2B-
PriDiscTmr- SecDiscTmr- DiscTmrStat- DiscTmrSERREn-
Capabilities: <access denied>
Kernel driver in use: pcieport
00:1c.3 PCI bridge [0604]: Intel Corporation NM10/ICH7 Family PCI Express Port 4 [8086:27d6] (rev 02) (prog-if 00 [Normal decode])
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR+ FastB2B- DisINTx+
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0, Cache Line Size: 32 bytes
Bus: primary=00, secondary=01, subordinate=01, sec-latency=0
I/O behind bridge: 0000e000-0000efff
Memory behind bridge: f7f00000-f7ffffff
Prefetchable memory behind bridge: 0000000080400000-00000000805fffff
Secondary status: 66MHz- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- <SERR- <PERR-
BridgeCtl: Parity- SERR+ NoISA- VGA- MAbort- >Reset- FastB2B-
PriDiscTmr- SecDiscTmr- DiscTmrStat- DiscTmrSERREn-
Capabilities: <access denied>
Kernel driver in use: pcieport
00:1d.0 USB controller [0c03]: Intel Corporation NM10/ICH7 Family USB UHCI Controller #1 [8086:27c8] (rev 02) (prog-if 00 [UHCI])
Subsystem: ASUSTeK Computer Inc. Device [1043:83ad]
Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap- 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0
Interrupt: pin A routed to IRQ 23
Region 4: I/O ports at d400 [size=32]
Kernel driver in use: uhci_hcd
00:1d.1 USB controller [0c03]: Intel Corporation NM10/ICH7 Family USB UHCI Controller #2 [8086:27c9] (rev 02) (prog-if 00 [UHCI])
Subsystem: ASUSTeK Computer Inc. Device [1043:83ad]
Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap- 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0
Interrupt: pin B routed to IRQ 19
Region 4: I/O ports at d480 [size=32]
Kernel driver in use: uhci_hcd
00:1d.2 USB controller [0c03]: Intel Corporation NM10/ICH7 Family USB UHCI Controller #3 [8086:27ca] (rev 02) (prog-if 00 [UHCI])
Subsystem: ASUSTeK Computer Inc. Device [1043:83ad]
Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap- 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0
Interrupt: pin C routed to IRQ 18
Region 4: I/O ports at d800 [size=32]
Kernel driver in use: uhci_hcd
00:1d.3 USB controller [0c03]: Intel Corporation NM10/ICH7 Family USB UHCI Controller #4 [8086:27cb] (rev 02) (prog-if 00 [UHCI])
Subsystem: ASUSTeK Computer Inc. Device [1043:83ad]
Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap- 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0
Interrupt: pin D routed to IRQ 16
Region 4: I/O ports at d880 [size=32]
Kernel driver in use: uhci_hcd
00:1d.7 USB controller [0c03]: Intel Corporation NM10/ICH7 Family USB2 EHCI Controller [8086:27cc] (rev 02) (prog-if 20 [EHCI])
Subsystem: ASUSTeK Computer Inc. Device [1043:83ad]
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0
Interrupt: pin A routed to IRQ 23
Region 0: Memory at f7cf7c00 (32-bit, non-prefetchable) [size=1K]
Capabilities: <access denied>
Kernel driver in use: ehci-pci
00:1e.0 PCI bridge [0604]: Intel Corporation 82801 Mobile PCI Bridge [8086:2448] (rev e2) (prog-if 01 [Subtractive decode])
Control: I/O- Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR+ FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0
Bus: primary=00, secondary=05, subordinate=05, sec-latency=32
Secondary status: 66MHz- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort+ <SERR- <PERR-
BridgeCtl: Parity- SERR+ NoISA- VGA- MAbort- >Reset- FastB2B-
PriDiscTmr- SecDiscTmr- DiscTmrStat- DiscTmrSERREn-
Capabilities: <access denied>
00:1f.0 ISA bridge [0601]: Intel Corporation NM10 Family LPC Controller [8086:27bc] (rev 02)
Subsystem: ASUSTeK Computer Inc. Device [1043:83ad]
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0
Capabilities: <access denied>
Kernel driver in use: lpc_ich
00:1f.2 SATA controller [0106]: Intel Corporation NM10/ICH7 Family SATA Controller [AHCI mode] [8086:27c1] (rev 02) (prog-if 01 [AHCI 1.0])
Subsystem: ASUSTeK Computer Inc. Device [1043:83ad]
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx+
Status: Cap+ 66MHz+ UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0
Interrupt: pin B routed to IRQ 43
Region 0: I/O ports at d080 [size=8]
Region 1: I/O ports at d000 [size=4]
Region 2: I/O ports at cc00 [size=8]
Region 3: I/O ports at c880 [size=4]
Region 4: I/O ports at c800 [size=32]
Region 5: Memory at f7cf7800 (32-bit, non-prefetchable) [size=1K]
Capabilities: <access denied>
Kernel driver in use: ahci
01:00.0 Ethernet controller [0200]: Atheros Communications Inc. AR8132 Fast Ethernet [1969:1062] (rev c0)
Subsystem: ASUSTeK Computer Inc. Device [1043:838a]
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0, Cache Line Size: 32 bytes
Interrupt: pin A routed to IRQ 46
Region 0: Memory at f7fc0000 (64-bit, non-prefetchable) [size=256K]
Region 2: I/O ports at ec00 [size=128]
Capabilities: <access denied>
Kernel driver in use: atl1c
02:00.0 Network controller [0280]: Broadcom Corporation BCM4313 802.11b/g/n Wireless LAN Controller [14e4:4727] (rev 01)
Subsystem: AzureWave Device [1a3b:2047]
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0, Cache Line Size: 32 bytes
Interrupt: pin A routed to IRQ 17
Region 0: Memory at fbffc000 (64-bit, non-prefetchable) [size=16K]
Capabilities: <access denied>
Kernel driver in use: bcma-pci-bridge
** USB devices:
Bus 001 Device 002: ID 046d:c52f Logitech, Inc. Wireless Mouse M305
Bus 005 Device 003: ID 058f:6366 Alcor Micro Corp. Multi Flash Reader
Bus 005 Device 004: ID 13d3:5702 IMC Networks UVC VGA Webcam
Bus 001 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub
Bus 002 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub
Bus 003 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub
Bus 004 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub
Bus 005 Device 001: ID 1d6b:0002 Linux Foundation 2.0 root hub
-- System Information:
Debian Release: 6.0.7
APT prefers stable-updates
APT policy: (500, 'stable-updates'), (500, 'oldstable-updates'), (500, 'stable'), (100, 'oldstable'), (100, 'unstable'), (100, 'testing'), (1, 'experimental')
Architecture: amd64 (x86_64)
Kernel: Linux 3.10-3-amd64 (SMP w/2 CPU cores)
Locale: LANG=pl_PL.utf8, LC_CTYPE=pl_PL.utf8 (charmap=UTF-8)
Shell: /bin/sh linked to /bin/dash
Versions of packages linux-image-3.11-1-amd64 depends on:
ii debconf [debconf-2.0] 1.5.36.1 Debian configuration management sy
ii initramfs-tools [linux-initra 0.115 generic modular initramfs generato
ii linux-base 3.5 Linux image base package
ii module-init-tools 3.12-2 tools for managing Linux kernel mo
Versions of packages linux-image-3.11-1-amd64 recommends:
ii firmware-linux-free 3.2 Binary firmware for various driver
Versions of packages linux-image-3.11-1-amd64 suggests:
pn debian-kernel-handbook <none> (no description available)
ii lilo 1:23.2-4 LInux LOader - the classic OS boot
pn linux-doc-3.11 <none> (no description available)
Versions of packages linux-image-3.11-1-amd64 is related to:
pn firmware-atheros <none> (no description available)
pn firmware-bnx2 <none> (no description available)
pn firmware-bnx2x <none> (no description available)
ii firmware-brcm80211 0.40 Binary firmware for Broadcom 802.1
pn firmware-intelwimax <none> (no description available)
pn firmware-ipw2x00 <none> (no description available)
pn firmware-ivtv <none> (no description available)
pn firmware-iwlwifi <none> (no description available)
pn firmware-libertas <none> (no description available)
pn firmware-linux <none> (no description available)
ii firmware-linux-nonfree 0.40 Binary firmware for various driver
pn firmware-myricom <none> (no description available)
pn firmware-netxen <none> (no description available)
pn firmware-qlogic <none> (no description available)
pn firmware-ralink <none> (no description available)
pn firmware-realtek <none> (no description available)
pn xen-hypervisor <none> (no description available)
-- debconf information:
linux-image-3.11-1-amd64/prerm/removing-running-kernel-3.11-1-amd64: true
linux-image-3.11-1-amd64/postinst/depmod-error-initrd-3.11-1-amd64: false
--- End Message ---