Bug#763320: linux-image-3.16-2-amd64: intel_idle enabled for Intel Atom S1260, causes high CPU temperature when idle
Package: src:linux
Version: 3.16.3-2
Severity: normal
Dear Maintainer,
with Kernel 3.16, intel_idle is enabled for the Intel Atom S1260 CPU
(Centerton SoC). This leads to a +20°C temperature increase when the CPU
is idle, exceeding the 100°C alarm threshold for passive cooled systems
like the Supermicro X9SBAA-F.
With 3.14, intel_idle was blacklisted for this CPU, which runs fine. If
3.16 is booted with intel_idle.max_cstate=0 processor.max_cstate=0,
which disables the intel_idle, the CPU also stays cool.
-- Package-specific info:
** Version:
Linux version 3.16-2-amd64 (debian-kernel@lists.debian.org) (gcc version 4.8.3 (Debian 4.8.3-11) ) #1 SMP Debian 3.16.3-2 (2014-09-20)
** Command line:
BOOT_IMAGE=/boot/vmlinuz-3.16-2-amd64 root=UUID=7b7b22dd-1baa-4772-a734-03ffc40db914 ro quiet console=ttyS1,115200n8 console=tty0 intel_idle.max_cstate=0 processor.max_cstate=0
** Not tainted
** Kernel log:
[ 2.983325] ata8.00: configured for UDMA/66
[ 2.983820] ata3.00: ATA-8: ST2000DL003-9VT166, CC3C, max UDMA/133
[ 2.983825] ata3.00: 3907029168 sectors, multi 0: LBA48 NCQ (depth 31/32)
[ 2.984577] ata3.00: configured for UDMA/133
[ 3.011761] usb 1-4: New USB device found, idVendor=0557, idProduct=2221
[ 3.011767] usb 1-4: New USB device strings: Mfr=1, Product=2, SerialNumber=0
[ 3.011771] usb 1-4: Product: Hermon USB hidmouse Device
[ 3.011776] usb 1-4: Manufacturer: Winbond Electronics Corp
[ 3.012035] usb 1-4: ep 0x82 - rounding interval to 64 microframes, ep desc says 80 microframes
[ 3.012046] usb 1-4: ep 0x81 - rounding interval to 64 microframes, ep desc says 80 microframes
[ 3.019168] hidraw: raw HID events driver (C) Jiri Kosina
[ 3.030160] ata1: SATA link up 6.0 Gbps (SStatus 133 SControl 300)
[ 3.030313] ata1.00: ATA-7: MARVELL Raid VD, MV.R00-0, max UDMA7
[ 3.030321] ata1.00: 3906865280 sectors, multi 0: LBA48 NCQ (depth 31/32)
[ 3.030471] ata1.00: configured for UDMA/133
[ 3.030722] scsi 0:0:0:0: Direct-Access ATA MARVELL Raid VD 00-0 PQ: 0 ANSI: 5
[ 3.031345] usbcore: registered new interface driver usbhid
[ 3.031351] usbhid: USB HID core driver
[ 3.031737] scsi 2:0:0:0: Direct-Access ATA ST2000DL003-9VT1 CC3C PQ: 0 ANSI: 5
[ 3.032928] scsi 7:0:0:0: Processor Marvell Console 1.01 PQ: 0 ANSI: 5
[ 3.033670] input: Winbond Electronics Corp Hermon USB hidmouse Device as /devices/pci0000:00/0000:00:02.0/0000:02:00.0/usb1/1-4/1-4:1.0/0003:0557:2221.0001/input/input0
[ 3.033959] hid-generic 0003:0557:2221.0001: input,hidraw0: USB HID v1.00 Mouse [Winbond Electronics Corp Hermon USB hidmouse Device] on usb-0000:02:00.0-4/input0
[ 3.034460] input: Winbond Electronics Corp Hermon USB hidmouse Device as /devices/pci0000:00/0000:00:02.0/0000:02:00.0/usb1/1-4/1-4:1.1/0003:0557:2221.0002/input/input1
[ 3.034625] hid-generic 0003:0557:2221.0002: input,hidraw1: USB HID v1.00 Keyboard [Winbond Electronics Corp Hermon USB hidmouse Device] on usb-0000:02:00.0-4/input1
[ 3.046153] ata8.00: exception Emask 0x0 SAct 0x0 SErr 0x0 action 0x6
[ 3.053518] ata8.00: irq_stat 0x40000001
[ 3.057990] scsi 7:0:0:0: CDB:
[ 3.057994] Inquiry: 12 01 00 00 ff 00
[ 3.058012] ata8.00: cmd a0/01:00:00:00:01/00:00:00:00:00/a0 tag 3 dma 16640 in
[ 3.058012] res 00/00:00:00:00:00/00:00:00:00:00/00 Emask 0x3 (HSM violation)
[ 3.075126] ata8: hard resetting link
[ 3.401934] ata8: SATA link up 1.5 Gbps (SStatus 113 SControl 300)
[ 3.402158] ata8.00: configured for UDMA/66
[ 3.402241] ata8: EH complete
[ 3.410424] scsi 0:0:0:0: Attached scsi generic sg0 type 0
[ 3.410654] scsi 2:0:0:0: Attached scsi generic sg1 type 0
[ 3.410830] scsi 7:0:0:0: Attached scsi generic sg2 type 3
[ 3.415232] sd 0:0:0:0: [sda] 3906865280 512-byte logical blocks: (2.00 TB/1.81 TiB)
[ 3.415438] sd 0:0:0:0: [sda] Write Protect is off
[ 3.415446] sd 0:0:0:0: [sda] Mode Sense: 00 3a 00 00
[ 3.415527] sd 0:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
[ 3.415633] sd 2:0:0:0: [sdb] 3907029168 512-byte logical blocks: (2.00 TB/1.81 TiB)
[ 3.415642] sd 2:0:0:0: [sdb] 4096-byte physical blocks
[ 3.415805] sd 2:0:0:0: [sdb] Write Protect is off
[ 3.415813] sd 2:0:0:0: [sdb] Mode Sense: 00 3a 00 00
[ 3.415884] sd 2:0:0:0: [sdb] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
[ 3.460487] sdb: sdb1 sdb2
[ 3.461418] sd 2:0:0:0: [sdb] Attached SCSI disk
[ 3.478857] sda: sda1 sda2
[ 3.479827] sd 0:0:0:0: [sda] Attached SCSI disk
[ 3.726640] PM: Starting manual resume from disk
[ 3.726652] PM: Hibernation image partition 8:17 present
[ 3.726655] PM: Looking for hibernation image.
[ 3.727413] PM: Image not found (code -22)
[ 3.727417] PM: Hibernation image not present or could not be loaded.
[ 3.838801] EXT4-fs (sda2): mounted filesystem with ordered data mode. Opts: (null)
[ 4.548055] random: nonblocking pool is initialized
[ 6.069726] systemd-udevd[348]: starting version 208
[ 6.604812] shpchp: Standard Hot Plug PCI Controller Driver version: 0.4
[ 6.621429] ACPI: processor limited to max C-state 0
[ 6.626403] input: Power Button as /devices/LNXSYSTM:00/LNXSYBUS:00/PNP0C0C:00/input/input2
[ 6.626417] ACPI: Power Button [PWRB]
[ 6.715825] ipmi message handler version 39.2
[ 6.870470] ismt_smbus 0000:00:13.0: enabling device (0140 -> 0142)
[ 6.870874] ismt_smbus 0000:00:13.0: irq 68 for MSI/MSI-X
[ 6.871180] ismt_smbus 0000:00:13.1: enabling device (0140 -> 0142)
[ 6.871507] ismt_smbus 0000:00:13.1: irq 69 for MSI/MSI-X
[ 6.873234] IPMI System Interface driver.
[ 6.873371] ipmi_si: probing via ACPI
[ 6.873452] ipmi_si 00:06: [io 0x0ca2] regsize 1 spacing 1 irq 0
[ 6.873459] ipmi_si: Adding ACPI-specified kcs state machine
[ 6.873520] ipmi_si: probing via SMBIOS
[ 6.873527] ipmi_si: SMBIOS: io 0xca2 regsize 1 spacing 1 irq 0
[ 6.873530] ipmi_si: Adding SMBIOS-specified kcs state machine duplicate interface
[ 6.873538] ipmi_si: probing via SPMI
[ 6.873543] ipmi_si: SPMI: io 0xca2 regsize 1 spacing 1 irq 0
[ 6.873546] ipmi_si: Adding SPMI-specified kcs state machine duplicate interface
[ 6.873554] ipmi_si: Trying ACPI-specified kcs state machine at i/o address 0xca2, slave address 0x0, irq 0
[ 6.912088] EFI Variables Facility v0.08 2004-May-17
[ 7.017131] ipmi_si 00:06: Found new BMC (man_id: 0x002a7c, prod_id: 0x0651, dev_id: 0x20)
[ 7.017168] ipmi_si 00:06: IPMI kcs interface initialized
[ 7.079210] kvm: disabled by bios
[ 7.113730] kvm: disabled by bios
[ 7.207631] [drm] Initialized drm 1.1.0 20060810
[ 38.813195] Adding 8388604k swap on /dev/sdb1. Priority:-1 extents:1 across:8388604k FS
[ 38.882522] EXT4-fs (sda2): re-mounted. Opts: (null)
[ 39.249950] EXT4-fs (sda2): re-mounted. Opts: errors=remount-ro
[ 40.279552] ipmi device interface
[ 40.346725] Copyright (C) 2004 MontaVista Software - IPMI Powerdown via sys_reboot.
[ 40.347523] IPMI poweroff: ATCA Detect mfg 0x2A7C prod 0x651
[ 40.347529] IPMI poweroff: Found a chassis style poweroff function
[ 40.417866] IPMI Watchdog: Unable to register misc device
[ 40.424022] IPMI Watchdog: set timeout error: -22
[ 40.424033] IPMI Watchdog: driver initialized
[ 40.655854] FAT-fs (sda1): utf8 is not a recommended IO charset for FAT filesystems, filesystem will be case sensitive!
[ 40.758328] EXT4-fs (sdb2): mounted filesystem with ordered data mode. Opts: errors=remount-ro
[ 42.304336] IPv6: ADDRCONF(NETDEV_UP): eth0: link is not ready
[ 45.678974] igb 0000:05:00.0 eth0: igb: eth0 NIC Link is Up 1000 Mbps Full Duplex, Flow Control: RX/TX
[ 45.679142] IPv6: ADDRCONF(NETDEV_CHANGE): eth0: link becomes ready
[ 66.125526] perf interrupt took too long (2517 > 2500), lowering kernel.perf_event_max_sample_rate to 50000
** Model information
sys_vendor: Supermicro
product_name: X9SBAA
product_version: 0123456789
chassis_vendor: Supermicro
chassis_version: 0123456789
bios_vendor: American Megatrends Inc.
bios_version: 1.1
board_vendor: Supermicro
board_name: X9SBAA
board_version: 0123456789
** Loaded modules:
msr
cpufreq_userspace
cpufreq_stats
cpufreq_conservative
cpufreq_powersave
nls_utf8
nls_cp437
vfat
fat
ipmi_watchdog
ipmi_poweroff
ipmi_devintf
ttm
drm_kms_helper
i2c_isch
drm
efi_pstore
coretemp
ie6xx_wdt
evdev
lpc_sch
kvm
mfd_core
efivars
ipmi_si
tpm_tis
i2c_ismt
ipmi_msghandler
tpm
acpi_cpufreq
button
processor
shpchp
ext4
crc16
mbcache
jbd2
sd_mod
crc_t10dif
crct10dif_generic
sg
crct10dif_common
hid_generic
usbhid
hid
ahci
libahci
xhci_hcd
igb
i2c_algo_bit
i2c_core
dca
ptp
pps_core
libata
usbcore
usb_common
scsi_mod
thermal
thermal_sys
** PCI devices:
00:00.0 Host bridge [0600]: Intel Corporation Atom Processor S1200 Internal [8086:0c75] (rev 02)
Subsystem: Intel Corporation Device [8086:0000]
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap- 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0
00:01.0 PCI bridge [0604]: Intel Corporation Atom Processor S1200 PCI Express Root Port 1 [8086:0c46] (rev 02) (prog-if 00 [Normal decode])
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr+ Stepping- SERR+ FastB2B- DisINTx+
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0, Cache Line Size: 64 bytes
Region 0: Memory at fe460000 (64-bit, non-prefetchable) [size=128K]
Bus: primary=00, secondary=01, subordinate=01, sec-latency=0
I/O behind bridge: 0000e000-0000efff
Memory behind bridge: fe300000-fe3fffff
Secondary status: 66MHz- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- <SERR- <PERR-
BridgeCtl: Parity+ SERR+ NoISA- VGA- MAbort- >Reset- FastB2B-
PriDiscTmr- SecDiscTmr- DiscTmrStat- DiscTmrSERREn-
Capabilities: <access denied>
Kernel driver in use: pcieport
00:02.0 PCI bridge [0604]: Intel Corporation Atom Processor S1200 PCI Express Root Port 2 [8086:0c47] (rev 02) (prog-if 00 [Normal decode])
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr+ Stepping- SERR+ FastB2B- DisINTx+
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0, Cache Line Size: 64 bytes
Region 0: Memory at fe440000 (64-bit, non-prefetchable) [size=128K]
Bus: primary=00, secondary=02, subordinate=02, sec-latency=0
Memory behind bridge: fe200000-fe2fffff
Secondary status: 66MHz- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- <SERR- <PERR-
BridgeCtl: Parity+ SERR+ NoISA- VGA- MAbort- >Reset- FastB2B-
PriDiscTmr- SecDiscTmr- DiscTmrStat- DiscTmrSERREn-
Capabilities: <access denied>
Kernel driver in use: pcieport
00:03.0 PCI bridge [0604]: Intel Corporation Atom Processor S1200 PCI Express Root Port 3 [8086:0c48] (rev 02) (prog-if 00 [Normal decode])
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr+ Stepping- SERR+ FastB2B- DisINTx+
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0, Cache Line Size: 64 bytes
Region 0: Memory at fe420000 (64-bit, non-prefetchable) [size=128K]
Bus: primary=00, secondary=03, subordinate=04, sec-latency=0
Memory behind bridge: fd800000-fe0fffff
Prefetchable memory behind bridge: 00000000fc000000-00000000fcffffff
Secondary status: 66MHz- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort+ <SERR- <PERR-
BridgeCtl: Parity+ SERR+ NoISA- VGA+ MAbort- >Reset- FastB2B-
PriDiscTmr- SecDiscTmr- DiscTmrStat- DiscTmrSERREn-
Capabilities: <access denied>
Kernel driver in use: pcieport
00:04.0 PCI bridge [0604]: Intel Corporation Atom Processor S1200 PCI Express Root Port 4 [8086:0c49] (rev 02) (prog-if 00 [Normal decode])
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr+ Stepping- SERR+ FastB2B- DisINTx+
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0, Cache Line Size: 64 bytes
Region 0: Memory at fe400000 (64-bit, non-prefetchable) [size=128K]
Bus: primary=00, secondary=05, subordinate=05, sec-latency=0
I/O behind bridge: 0000d000-0000dfff
Memory behind bridge: fe100000-fe1fffff
Prefetchable memory behind bridge: 00000000d0000000-00000000d00fffff
Secondary status: 66MHz- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort+ <SERR- <PERR-
BridgeCtl: Parity+ SERR+ NoISA- VGA- MAbort- >Reset- FastB2B-
PriDiscTmr- SecDiscTmr- DiscTmrStat- DiscTmrSERREn-
Capabilities: <access denied>
Kernel driver in use: pcieport
00:0e.0 IOMMU [0806]: Intel Corporation Atom Processor S1200 Internal [8086:0c54] (rev 02)
Subsystem: Intel Corporation Device [8086:0000]
Control: I/O- Mem- BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr+ Stepping- SERR+ FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Interrupt: pin A routed to IRQ 5
Capabilities: <access denied>
00:13.0 System peripheral [0880]: Intel Corporation Atom Processor S1200 SMBus 2.0 Controller 0 [8086:0c59] (rev 02)
Subsystem: Intel Corporation Device [8086:0000]
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr+ Stepping- SERR+ FastB2B- DisINTx+
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0
Interrupt: pin D routed to IRQ 68
Region 0: Memory at fe482000 (64-bit, non-prefetchable) [size=1K]
Capabilities: <access denied>
Kernel driver in use: ismt_smbus
00:13.1 System peripheral [0880]: Intel Corporation Atom Processor S1200 SMBus 2.0 Controller 1 [8086:0c5a] (rev 02)
Subsystem: Intel Corporation Device [8086:0000]
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr+ Stepping- SERR+ FastB2B- DisINTx+
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0
Interrupt: pin D routed to IRQ 69
Region 0: Memory at fe481000 (64-bit, non-prefetchable) [size=1K]
Capabilities: <access denied>
Kernel driver in use: ismt_smbus
00:14.0 Serial controller [0700]: Intel Corporation Atom Processor S1200 UART [8086:0c5f] (rev 02) (prog-if 02 [16550])
Subsystem: Super Micro Computer Inc Device [15d9:0651]
Control: I/O+ Mem+ BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR+ FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Interrupt: pin A routed to IRQ 16
Region 0: I/O ports at f000 [size=8]
Region 1: Memory at fe480000 (32-bit, non-prefetchable) [size=256]
Capabilities: <access denied>
Kernel driver in use: serial
00:1f.0 ISA bridge [0601]: Intel Corporation Atom Processor S1200 Integrated Legacy Bus [8086:0c60] (rev 02)
Subsystem: Super Micro Computer Inc Device [15d9:0651]
Control: I/O+ Mem+ BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap- 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Kernel driver in use: lpc_sch
01:00.0 SATA controller [0106]: Marvell Technology Group Ltd. 88SE9230 PCIe SATA 6Gb/s Controller [1b4b:9230] (rev 10) (prog-if 01 [AHCI 1.0])
Subsystem: Marvell Technology Group Ltd. 88SE9230 PCIe SATA 6Gb/s Controller [1b4b:9230]
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr+ Stepping- SERR+ FastB2B- DisINTx+
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0, Cache Line Size: 64 bytes
Interrupt: pin A routed to IRQ 53
Region 0: I/O ports at e050 [size=8]
Region 1: I/O ports at e040 [size=4]
Region 2: I/O ports at e030 [size=8]
Region 3: I/O ports at e020 [size=4]
Region 4: I/O ports at e000 [size=32]
Region 5: Memory at fe310000 (32-bit, non-prefetchable) [size=2K]
Expansion ROM at fe300000 [disabled] [size=64K]
Capabilities: <access denied>
Kernel driver in use: ahci
02:00.0 USB controller [0c03]: Renesas Technology Corp. uPD720201 USB 3.0 Host Controller [1912:0014] (rev 03) (prog-if 30 [XHCI])
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr+ Stepping- SERR+ FastB2B- DisINTx+
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0, Cache Line Size: 64 bytes
Interrupt: pin A routed to IRQ 21
Region 0: Memory at fe200000 (64-bit, non-prefetchable) [size=8K]
Capabilities: <access denied>
Kernel driver in use: xhci_hcd
03:00.0 PCI bridge [0604]: Tundra Semiconductor Corp. Device [10e3:8113] (rev 01) (prog-if 00 [Normal decode])
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr+ Stepping- SERR+ FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0
Bus: primary=03, secondary=04, subordinate=04, sec-latency=64
Memory behind bridge: fd800000-fe0fffff
Prefetchable memory behind bridge: 00000000fc000000-00000000fcffffff
Secondary status: 66MHz+ FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort+ <SERR- <PERR-
BridgeCtl: Parity+ SERR+ NoISA- VGA+ MAbort- >Reset- FastB2B-
PriDiscTmr- SecDiscTmr- DiscTmrStat- DiscTmrSERREn-
Capabilities: <access denied>
04:03.0 VGA compatible controller [0300]: Matrox Electronics Systems Ltd. MGA G200eW WPCM450 [102b:0532] (rev 0a) (prog-if 00 [VGA controller])
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 64 (4000ns min, 8000ns max), Cache Line Size: 64 bytes
Interrupt: pin A routed to IRQ 10
Region 0: Memory at fc000000 (32-bit, prefetchable) [size=16M]
Region 1: Memory at fe000000 (32-bit, non-prefetchable) [size=16K]
Region 2: Memory at fd800000 (32-bit, non-prefetchable) [size=8M]
Expansion ROM at <unassigned> [disabled]
Capabilities: <access denied>
05:00.0 Ethernet controller [0200]: Intel Corporation I350 Gigabit Network Connection [8086:1521] (rev 01)
Subsystem: Super Micro Computer Inc Device [15d9:1521]
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr+ Stepping- SERR+ FastB2B- DisINTx+
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0, Cache Line Size: 64 bytes
Interrupt: pin A routed to IRQ 21
Region 0: Memory at fe120000 (32-bit, non-prefetchable) [size=128K]
Region 2: I/O ports at d020 [size=32]
Region 3: Memory at fe144000 (32-bit, non-prefetchable) [size=16K]
Capabilities: <access denied>
Kernel driver in use: igb
05:00.1 Ethernet controller [0200]: Intel Corporation I350 Gigabit Network Connection [8086:1521] (rev 01)
Subsystem: Super Micro Computer Inc Device [15d9:1521]
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr+ Stepping- SERR+ FastB2B- DisINTx+
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0, Cache Line Size: 64 bytes
Interrupt: pin B routed to IRQ 22
Region 0: Memory at fe100000 (32-bit, non-prefetchable) [size=128K]
Region 2: I/O ports at d000 [size=32]
Region 3: Memory at fe140000 (32-bit, non-prefetchable) [size=16K]
Capabilities: <access denied>
Kernel driver in use: igb
** USB devices:
Bus 002 Device 001: ID 1d6b:0003 Linux Foundation 3.0 root hub
Bus 001 Device 003: ID 0557:2221 ATEN International Co., Ltd Winbond Hermon
Bus 001 Device 002: ID 04fa:2490 Dallas Semiconductor DS1490F 2-in-1 Fob, 1-Wire adapter
Bus 001 Device 001: ID 1d6b:0002 Linux Foundation 2.0 root hub
-- System Information:
Debian Release: jessie/sid
APT prefers testing
APT policy: (500, 'testing')
Architecture: amd64 (x86_64)
Kernel: Linux 3.16-2-amd64 (SMP w/4 CPU cores)
Locale: LANG=en_US.UTF-8, LC_CTYPE=en_US.UTF-8 (charmap=UTF-8)
Shell: /bin/sh linked to /bin/dash
Versions of packages linux-image-3.16-2-amd64 depends on:
ii debconf [debconf-2.0] 1.5.53
ii initramfs-tools [linux-initramfs-tool] 0.116
ii kmod 18-3
ii linux-base 3.5
ii module-init-tools 18-3
Versions of packages linux-image-3.16-2-amd64 recommends:
ii firmware-linux-free 3.3
Versions of packages linux-image-3.16-2-amd64 suggests:
pn debian-kernel-handbook <none>
pn grub-pc | extlinux | lilo <none>
pn linux-doc-3.16 <none>
Versions of packages linux-image-3.16-2-amd64 is related to:
pn firmware-atheros <none>
pn firmware-bnx2 <none>
pn firmware-bnx2x <none>
pn firmware-brcm80211 <none>
pn firmware-intelwimax <none>
pn firmware-ipw2x00 <none>
pn firmware-ivtv <none>
pn firmware-iwlwifi <none>
pn firmware-libertas <none>
pn firmware-linux <none>
pn firmware-linux-nonfree <none>
pn firmware-myricom <none>
pn firmware-netxen <none>
pn firmware-qlogic <none>
pn firmware-ralink <none>
pn firmware-realtek <none>
pn xen-hypervisor <none>
-- debconf information:
linux-image-3.16-2-amd64/prerm/removing-running-kernel-3.16-2-amd64: true
linux-image-3.16-2-amd64/postinst/depmod-error-initrd-3.16-2-amd64: false
linux-image-3.16-2-amd64/postinst/mips-initrd-3.16-2-amd64:
Reply to: