[Date Prev][Date Next] [Thread Prev][Thread Next] [Date Index] [Thread Index]

Bug#578063: marked as done (linux-image-2.6.32-3-686: module i915 does not create /dev/dri during boot. Creates it after reloading)

Your message dated Thu, 6 Jun 2013 00:13:24 +0200
with message-id <20130605221323.GD5444@pisco.westfalen.local>
and subject line Closing
has caused the Debian Bug report #578063,
regarding linux-image-2.6.32-3-686: module i915 does not create /dev/dri during boot. Creates it after reloading
to be marked as done.

This means that you claim that the problem has been dealt with.
If this is not the case it is now your responsibility to reopen the
Bug report if necessary, and/or fix the problem forthwith.

(NB: If you are a system administrator and have no idea what this
message is talking about, this may indicate a serious mail system
misconfiguration somewhere. Please contact owner@bugs.debian.org
immediately.)


-- 
578063: http://bugs.debian.org/cgi-bin/bugreport.cgi?bug=578063
Debian Bug Tracking System
Contact owner@bugs.debian.org with problems
--- Begin Message --- 
Package: linux-2.6
Version: 2.6.32-9
Severity: normal

*** Please type your report below this line ***
After boot the i915 module gets loaded, but no /dev/dri directory is created
and acceleration in the X server doesn't work.
When I remove and reload the module by hand:
# rmmod i915 ; modprobe i915
The /dev/dri directory is created and acceleration works perfectly.
I attach the X server logs.
Xorg.0.noacceleration.gz - after boot
Xorg.0.acceleration.gz - after reloading of i915 and restartinf of X server

I tried to reinstall drm related packages:
# apt-get install libdrm-intel1  libdrm2 --reinstall
according to https://bugs.launchpad.net/ubuntu/+source/libdrm/+bug/430876
(similar problem detected in ubuntu), but it didn't help.

-- Package-specific info:
** Kernel log: boot messages should be attached

** Model information
not available

** Network interface configuration:
# This file describes the network interfaces available on your system
# and how to activate them. For more information, see interfaces(5).

# The loopback network interface
auto lo
iface lo inet loopback

# The primary network interface
allow-hotplug eth1
iface eth1 inet dhcp

auto eth1
#iface wlan0 inet dhcp
#wpa-conf /etc/wpa_supplicant_weiti.conf
iface eth0_rename inet dhcp
wpa-conf /etc/wpa_supplicant_weiti.conf
iface wlan1 inet dhcp
wpa-conf /etc/wpa_supplicant_weiti.conf

** PCI devices:
00:00.0 Host bridge [0600]: Intel Corporation Mobile 915GM/PM/GMS/910GML
Express Processor to DRAM Controller [8086:2590] (rev 03)
    Subsystem: Hewlett-Packard Company NX6110/NC6120 [103c:099c]
    Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B- DisINTx-
    Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=fast >TAbort-
<TAbort- <MAbort+ >SERR- <PERR- INTx-
    Latency: 0
    Capabilities: [e0] Vendor Specific Information: Len=09 <?>
    Kernel driver in use: agpgart-intel

00:02.0 VGA compatible controller [0300]: Intel Corporation Mobile
915GM/GMS/910GML Express Graphics Controller [8086:2592] (rev 03)
(prog-if 00 [VGA controller])
    Subsystem: Hewlett-Packard Company NX6110/NC6120 [103c:099c]
    Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B- DisINTx-
    Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=fast >TAbort-
<TAbort- <MAbort- >SERR- <PERR- INTx-
    Latency: 0
    Interrupt: pin A routed to IRQ 16
    Region 0: Memory at d0400000 (32-bit, non-prefetchable) [size=512K]
    Region 1: I/O ports at 7000 [size=8]
    Region 2: Memory at c0000000 (32-bit, prefetchable) [size=256M]
    Region 3: Memory at d0480000 (32-bit, non-prefetchable) [size=256K]
    Expansion ROM at <unassigned> [disabled]
    Capabilities: [d0] Power Management version 2
        Flags: PMEClk- DSI+ D1- D2- AuxCurrent=0mA
PME(D0-,D1-,D2-,D3hot-,D3cold-)
        Status: D0 NoSoftRst- PME-Enable- DSel=0 DScale=0 PME-

00:02.1 Display controller [0380]: Intel Corporation Mobile
915GM/GMS/910GML Express Graphics Controller [8086:2792] (rev 03)
    Subsystem: Hewlett-Packard Company NX6110/NC6120 [103c:099c]
    Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B- DisINTx-
    Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=fast >TAbort-
<TAbort- <MAbort- >SERR- <PERR- INTx-
    Latency: 0
    Region 0: Memory at d0500000 (32-bit, non-prefetchable) [size=512K]
    Capabilities: [d0] Power Management version 2
        Flags: PMEClk- DSI+ D1- D2- AuxCurrent=0mA
PME(D0-,D1-,D2-,D3hot-,D3cold-)
        Status: D0 NoSoftRst- PME-Enable- DSel=0 DScale=0 PME-

00:1d.0 USB Controller [0c03]: Intel Corporation 82801FB/FBM/FR/FW/FRW
(ICH6 Family) USB UHCI #1 [8086:2658] (rev 03) (prog-if 00 [UHCI])
    Subsystem: Hewlett-Packard Company NX6110/NC6120 [103c:099c]
    Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B- DisINTx-
    Status: Cap- 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR- INTx-
    Latency: 0
    Interrupt: pin A routed to IRQ 23
    Region 4: I/O ports at 2000 [size=32]
    Kernel driver in use: uhci_hcd

00:1d.1 USB Controller [0c03]: Intel Corporation 82801FB/FBM/FR/FW/FRW
(ICH6 Family) USB UHCI #2 [8086:2659] (rev 03) (prog-if 00 [UHCI])
    Subsystem: Hewlett-Packard Company NX6110/NC6120 [103c:099c]
    Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B- DisINTx-
    Status: Cap- 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR- INTx-
    Latency: 0
    Interrupt: pin B routed to IRQ 17
    Region 4: I/O ports at 2020 [size=32]
    Kernel driver in use: uhci_hcd

00:1d.2 USB Controller [0c03]: Intel Corporation 82801FB/FBM/FR/FW/FRW
(ICH6 Family) USB UHCI #3 [8086:265a] (rev 03) (prog-if 00 [UHCI])
    Subsystem: Hewlett-Packard Company NX6110/NC6120 [103c:099c]
    Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B- DisINTx-
    Status: Cap- 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR- INTx-
    Latency: 0
    Interrupt: pin C routed to IRQ 18
    Region 4: I/O ports at 2040 [size=32]
    Kernel driver in use: uhci_hcd

00:1d.3 USB Controller [0c03]: Intel Corporation 82801FB/FBM/FR/FW/FRW
(ICH6 Family) USB UHCI #4 [8086:265b] (rev 03) (prog-if 00 [UHCI])
    Subsystem: Hewlett-Packard Company NX6110/NC6120 [103c:099c]
    Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B- DisINTx-
    Status: Cap- 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR- INTx-
    Latency: 0
    Interrupt: pin D routed to IRQ 19
    Region 4: I/O ports at 2060 [size=32]
    Kernel driver in use: uhci_hcd

00:1d.7 USB Controller [0c03]: Intel Corporation 82801FB/FBM/FR/FW/FRW
(ICH6 Family) USB2 EHCI Controller [8086:265c] (rev 03) (prog-if 20 [EHCI])
    Subsystem: Hewlett-Packard Company NX6110/NC6120 [103c:099c]
    Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B- DisINTx-
    Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR- INTx-
    Latency: 0
    Interrupt: pin A routed to IRQ 23
    Region 0: Memory at d0580000 (32-bit, non-prefetchable) [size=1K]
    Capabilities: [50] Power Management version 2
        Flags: PMEClk- DSI- D1- D2- AuxCurrent=375mA
PME(D0+,D1-,D2-,D3hot+,D3cold+)
        Status: D0 NoSoftRst- PME-Enable- DSel=0 DScale=0 PME-
    Capabilities: [58] Debug port: BAR=1 offset=00a0
    Kernel driver in use: ehci_hcd

00:1e.0 PCI bridge [0604]: Intel Corporation 82801 Mobile PCI Bridge
[8086:2448] (rev d3) (prog-if 01 [Subtractive decode])
    Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR+ FastB2B- DisINTx-
    Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort-
<TAbort- <MAbort- >SERR- <PERR- INTx-
    Latency: 0
    Bus: primary=00, secondary=02, subordinate=06, sec-latency=32
    I/O behind bridge: 00003000-00003fff
    Memory behind bridge: d0000000-d03fffff
    Prefetchable memory behind bridge: 0000000030000000-0000000033ffffff
    Secondary status: 66MHz- FastB2B+ ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort+ <SERR- <PERR-
    BridgeCtl: Parity- SERR+ NoISA+ VGA- MAbort- >Reset- FastB2B-
        PriDiscTmr- SecDiscTmr- DiscTmrStat- DiscTmrSERREn-
    Capabilities: [50] Subsystem: Hewlett-Packard Company NX6110/NC6120
[103c:099c]

00:1e.2 Multimedia audio controller [0401]: Intel Corporation
82801FB/FBM/FR/FW/FRW (ICH6 Family) AC'97 Audio Controller [8086:266e]
(rev 03)
    Subsystem: Hewlett-Packard Company NX6110/NC6120 [103c:099c]
    Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B- DisINTx-
    Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR- INTx-
    Latency: 0
    Interrupt: pin A routed to IRQ 21
    Region 0: I/O ports at 2100 [size=256]
    Region 1: I/O ports at 2200 [size=64]
    Region 2: Memory at d0581000 (32-bit, non-prefetchable) [size=512]
    Region 3: Memory at d0582000 (32-bit, non-prefetchable) [size=256]
    Capabilities: [50] Power Management version 2
        Flags: PMEClk- DSI- D1- D2- AuxCurrent=375mA
PME(D0+,D1-,D2-,D3hot+,D3cold+)
        Status: D0 NoSoftRst- PME-Enable- DSel=0 DScale=0 PME-
    Kernel driver in use: Intel ICH

00:1e.3 Modem [0703]: Intel Corporation 82801FB/FBM/FR/FW/FRW (ICH6
Family) AC'97 Modem Controller [8086:266d] (rev 03) (prog-if 00 [Generic])
    Subsystem: Hewlett-Packard Company NX6110/NC6120 [103c:099c]
    Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B- DisINTx-
    Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR- INTx-
    Latency: 0
    Interrupt: pin B routed to IRQ 22
    Region 0: I/O ports at 2400 [size=256]
    Region 1: I/O ports at 2500 [size=128]
    Capabilities: [50] Power Management version 2
        Flags: PMEClk- DSI- D1- D2- AuxCurrent=375mA
PME(D0+,D1-,D2-,D3hot+,D3cold+)
        Status: D0 NoSoftRst- PME-Enable- DSel=0 DScale=0 PME-
    Kernel driver in use: Intel ICH Modem

00:1f.0 ISA bridge [0601]: Intel Corporation 82801FBM (ICH6M) LPC
Interface Bridge [8086:2641] (rev 03)
    Subsystem: Hewlett-Packard Company NX6110/NC6120 [103c:099c]
    Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR+ FastB2B- DisINTx-
    Status: Cap- 66MHz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR- INTx-
    Latency: 0

00:1f.1 IDE interface [0101]: Intel Corporation 82801FB/FBM/FR/FW/FRW
(ICH6 Family) IDE Controller [8086:266f] (rev 03) (prog-if 8a [Master
SecP PriP])
    Subsystem: Hewlett-Packard Company NX6110/NC6120 [103c:099c]
    Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B- DisINTx-
    Status: Cap- 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR- INTx-
    Latency: 0
    Interrupt: pin A routed to IRQ 16
    Region 0: I/O ports at 01f0 [size=8]
    Region 1: I/O ports at 03f4 [size=1]
    Region 2: I/O ports at 0170 [size=8]
    Region 3: I/O ports at 0374 [size=1]
    Region 4: I/O ports at 2580 [size=16]
    Kernel driver in use: PIIX_IDE

02:04.0 Network controller [0280]: Intel Corporation PRO/Wireless 2200BG
[Calexico2] Network Connection [8086:4220] (rev 05)
    Subsystem: Hewlett-Packard Company Compaq nw8240/nx8220 [103c:12f6]
    Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B- DisINTx-
    Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR- INTx-
    Latency: 64 (750ns min, 6000ns max), Cache Line Size: 64 bytes
    Interrupt: pin A routed to IRQ 21
    Region 0: Memory at d0000000 (32-bit, non-prefetchable) [size=4K]
    Capabilities: [dc] Power Management version 2
        Flags: PMEClk- DSI+ D1- D2- AuxCurrent=0mA
PME(D0+,D1-,D2-,D3hot+,D3cold+)
        Status: D0 NoSoftRst- PME-Enable- DSel=0 DScale=1 PME-
    Kernel driver in use: ipw2200

02:06.0 CardBus bridge [0607]: Texas Instruments PCIxx21/x515 Cardbus
Controller [104c:8031]
    Subsystem: Hewlett-Packard Company NX6110/NC6120 [103c:099c]
    Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B- DisINTx-
    Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR- INTx-
    Latency: 168, Cache Line Size: 32 bytes
    Interrupt: pin A routed to IRQ 18
    Region 0: Memory at d0001000 (32-bit, non-prefetchable) [size=4K]
    Bus: primary=02, secondary=03, subordinate=06, sec-latency=176
    Memory window 0: 30000000-33fff000 (prefetchable)
    Memory window 1: 34000000-37fff000
    I/O window 0: 00003000-000030ff
    I/O window 1: 00003400-000034ff
    BridgeCtl: Parity- SERR- ISA- VGA- MAbort- >Reset+ 16bInt+ PostWrite+
    16-bit legacy interface ports at 0001
    Kernel driver in use: yenta_cardbus

02:06.2 FireWire (IEEE 1394) [0c00]: Texas Instruments OHCI Compliant
IEEE 1394 Host Controller [104c:8032] (prog-if 10 [OHCI])
    Subsystem: Hewlett-Packard Company NX6110/NC6120 [103c:099c]
    Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B- DisINTx-
    Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR- INTx-
    Latency: 64 (500ns min, 1000ns max), Cache Line Size: 64 bytes
    Interrupt: pin C routed to IRQ 22
    Region 0: Memory at d0002000 (32-bit, non-prefetchable) [size=2K]
    Region 1: Memory at d0004000 (32-bit, non-prefetchable) [size=16K]
    Capabilities: [44] Power Management version 2
        Flags: PMEClk- DSI- D1+ D2+ AuxCurrent=0mA
PME(D0+,D1+,D2+,D3hot+,D3cold-)
        Status: D0 NoSoftRst- PME-Enable- DSel=0 DScale=0 PME+
    Kernel driver in use: firewire_ohci

02:0e.0 Ethernet controller [0200]: Broadcom Corporation BCM4401-B0
100Base-TX [14e4:170c] (rev 02)
    Subsystem: Hewlett-Packard Company NX6110/NC6120 [103c:099c]
    Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B- DisINTx-
    Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort-
<TAbort- <MAbort- >SERR- <PERR- INTx-
    Latency: 64
    Interrupt: pin A routed to IRQ 16
    Region 0: Memory at d0008000 (32-bit, non-prefetchable) [size=8K]
    Capabilities: [40] Power Management version 2
        Flags: PMEClk- DSI- D1+ D2+ AuxCurrent=0mA
PME(D0+,D1+,D2+,D3hot+,D3cold+)
        Status: D0 NoSoftRst- PME-Enable- DSel=0 DScale=2 PME-
    Kernel driver in use: b44


** USB devices:
Bus 005 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub
Bus 002 Device 002: ID 046d:c03e Logitech, Inc. Premium Optical Wheel Mouse
Bus 002 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub
Bus 003 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub
Bus 004 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub
Bus 001 Device 001: ID 1d6b:0002 Linux Foundation 2.0 root hub


-- System Information:
Debian Release: squeeze/sid
  APT prefers testing
  APT policy: (500, 'testing'), (1, 'experimental')
Architecture: i386 (i686)

Kernel: Linux 2.6.32-trunk-686 (SMP w/1 CPU core)
Locale: LANG=pl_PL.UTF-8, LC_CTYPE=pl_PL.UTF-8 (charmap=UTF-8)
Shell: /bin/sh linked to /bin/dash

Versions of packages linux-image-2.6.32-3-686 depends on:
ii  debconf [debconf-2.0]        1.5.30      Debian configuration
management sy
ii  initramfs-tools [linux-initr 0.93.4      tools for generating an
initramfs
ii  module-init-tools            3.12~pre2-1 tools for managing Linux
kernel mo

Versions of packages linux-image-2.6.32-3-686 recommends:
pn  firmware-linux-free           <none>     (no description available)
ii  libc6-i686                    2.10.2-6   GNU C Library: Shared
libraries [i

Versions of packages linux-image-2.6.32-3-686 suggests:
ii  grub                          0.97-59    GRand Unified Bootloader
(dummy pa
pn  linux-doc-2.6.32              <none>     (no description available)

Versions of packages linux-image-2.6.32-3-686 is related to:
pn  firmware-bnx2                 <none>     (no description available)
pn  firmware-bnx2x                <none>     (no description available)
pn  firmware-ipw2x00              <none>     (no description available)
pn  firmware-ivtv                 <none>     (no description available)
pn  firmware-iwlwifi              <none>     (no description available)
pn  firmware-linux                <none>     (no description available)
pn  firmware-linux-nonfree        <none>     (no description available)
pn  firmware-qlogic               <none>     (no description available)
pn  firmware-ralink               <none>     (no description available)

-- debconf information:
 
linux-image-2.6.32-3-686/prerm/would-invalidate-boot-loader-2.6.32-3-686:
true
  shared/kernel-image/really-run-bootloader: true
  linux-image-2.6.32-3-686/postinst/bootloader-error-2.6.32-3-686:
  linux-image-2.6.32-3-686/postinst/depmod-error-initrd-2.6.32-3-686: false
  linux-image-2.6.32-3-686/postinst/bootloader-test-error-2.6.32-3-686:
  linux-image-2.6.32-3-686/postinst/missing-firmware-2.6.32-3-686:
  linux-image-2.6.32-3-686/prerm/removing-running-kernel-2.6.32-3-686: true

Attachment: Xorg.0.acceleration.gz
Description: GNU Zip compressed data

Attachment: Xorg.0.noacceleration.gz
Description: GNU Zip compressed data


--- End Message ---
--- Begin Message --- 
Hi,
your bug has been filed against the "linux-2.6" source package and was filed for
a kernel older than the recently released Debian 7.0 / Wheezy with a severity
less than important.

We don't have the ressources to reproduce the complete backlog of all older kernel
bugs, so we're closing this bug for now. If you can reproduce the bug with Debian Wheezy
or a more recent kernel from testing or unstable, please reopen the bug by sending
a mail to control@bugs.debian.org with the following three commands included in the
mail:

reopen BUGNUMBER
reassign BUGNUMBER src:linux
thanks

Cheers,
        Moritz

--- End Message ---
Reply to: