--- Begin Message ---
- To: submit@bugs.debian.org
- Subject: linux-image-2.6.26-1-686: iowait spikes after lenny upgrade, pdflush & kjournald use 99% io on xfs filesystem]
- From: Chris Quirk <chris@marblemedia.com>
- Date: Mon, 23 Feb 2009 15:14:16 -0500
- Message-id: <49A30398.7030102@marblemedia.com>
Package: linux-image-2.6.26-1-686
Version: 2.6.26-13
Severity: important
System was upgraded from etch to lenny. pdflush and kjournald take 99% of
IO, iostat shows increasing IO wait % whenever disk is accessed
/dev/sda10 is xfs formatted, running from a Dell perc raid.
http://forums.debian.net/viewtopic.php?t=35993
http://people.binf.ku.dk/~hanne/b2evolution/blogs/index.php?blog=5&title=tuning-vm-on-24-core-128-gb-ram-machine&disp=single&more=1&c=1&tb=1&pb=1
-- Package-specific info:
** Version:
Linux version 2.6.26-1-686 (Debian 2.6.26-13) (waldi@debian.org) (gcc version 4.1.3 20080704 (prerelease) (Debian 4.1.2-24)) #1 SMP Sat Jan 10 18:29:31 UTC 2009
** Command line:
root=/dev/sda5 ro
** Not tainted
** Kernel log:
[ 5.076337] usb usb1: Manufacturer: Linux 2.6.26-1-686 ohci_hcd
[ 5.076337] usb usb1: SerialNumber: 0000:00:0f.2
[ 5.132337] tg3.c:v3.92.1 (June 9, 2008)
[ 5.132337] ACPI: PCI Interrupt 0000:03:06.0[A] -> GSI 28 (level, low) -> IRQ 28
[ 5.132337] ACPI: PCI Interrupt 0000:04:08.1[A] -> GSI 30 (level, low) -> IRQ 30
[ 5.174534] eth0: Tigon3 [partno(BCM95703A30) rev 1002 PHY(5703)] (PCIX:133MHz:64-bit) 10/100/1000Base-T Ethernet 00:0d:56:bb:bf:6a
[ 5.174646] eth0: RXcsums[1] LinkChgREG[0] MIirq[0] ASF[0] WireSpeed[1] TSOcap[1]
[ 5.174646] eth0: dma_rwctrl[769c4000] dma_mask[64-bit]
[ 5.175803] AAC0: kernel 2.8-1[6098]
[ 5.174646] ACPI: PCI Interrupt 0000:03:08.0[A] -> GSI 29 (level, low) -> IRQ 29
[ 5.176007] AAC0: monitor 2.8-1[6098]
[ 5.176074] AAC0: bios 2.8-1[6098]
[ 5.176140] AAC0: serial ABC881D3
[ 5.174647] scsi0 : percraid
[ 5.174647] scsi 0:0:0:0: Direct-Access DELL PERC RAID5 V1.0 PQ: 0 ANSI: 2
[ 5.174647] scsi 0:0:1:0: Direct-Access DELL BACKUP_DRIVE V1.0 PQ: 0 ANSI: 2
[ 5.194427] scsi 0:1:0:0: Direct-Access MAXTOR ATLAS15K_73SCA DT60 PQ: 0 ANSI: 3
[ 5.195766] scsi 0:1:1:0: Direct-Access MAXTOR ATLAS15K_73SCA DT60 PQ: 0 ANSI: 3
[ 5.198427] scsi 0:1:2:0: Direct-Access MAXTOR ATLAS15K_73SCA DT60 PQ: 0 ANSI: 3
[ 5.198427] scsi 0:1:3:0: Direct-Access MAXTOR ATLAS15K_73SCA DT60 PQ: 0 ANSI: 3
[ 5.202453] scsi 0:1:4:0: Direct-Access SEAGATE ST3146807LC DS09 PQ: 0 ANSI: 3
[ 5.221224] eth1: Tigon3 [partno(BCM95703A30) rev 1002 PHY(5703)] (PCIX:133MHz:64-bit) 10/100/1000Base-T Ethernet 00:0d:56:bb:bf:6c
[ 5.221322] eth1: RXcsums[1] LinkChgREG[0] MIirq[0] ASF[0] WireSpeed[1] TSOcap[1]
[ 5.221407] eth1: dma_rwctrl[769c4000] dma_mask[64-bit]
[ 5.242956] hda: ATAPI 24X CD-ROM drive, 128kB Cache
[ 5.243167] Uniform CD-ROM driver Revision: 3.20
[ 5.420020] scsi 0:1:6:0: Processor PE/PV 1x5 SCSI BP 1.1 PQ: 0 ANSI: 2
[ 13.669945] Driver 'sd' needs updating - please use bus_type methods
[ 13.669945] sd 0:0:0:0: [sda] 430071552 512-byte hardware sectors (220197 MB)
[ 13.669945] sd 0:0:0:0: [sda] Write Protect is off
[ 13.669945] sd 0:0:0:0: [sda] Mode Sense: 06 00 00 00
[ 13.669945] sd 0:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
[ 13.670151] sd 0:0:0:0: [sda] 430071552 512-byte hardware sectors (220197 MB)
[ 13.670302] sd 0:0:0:0: [sda] Write Protect is off
[ 13.670382] sd 0:0:0:0: [sda] Mode Sense: 06 00 00 00
[ 13.670929] sd 0:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
[ 13.671034] sda: sda1 sda2 sda3 < sda5 sda6 sda7 sda8 sda9 sda10 >
[ 13.707323] sd 0:0:0:0: [sda] Attached SCSI removable disk
[ 13.707630] sd 0:0:1:0: [sdb] 286716544 512-byte hardware sectors (146799 MB)
[ 13.707774] sd 0:0:1:0: [sdb] Write Protect is off
[ 13.707848] sd 0:0:1:0: [sdb] Mode Sense: 06 00 00 00
[ 13.707939] sd 0:0:1:0: [sdb] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
[ 13.708129] sd 0:0:1:0: [sdb] 286716544 512-byte hardware sectors (146799 MB)
[ 13.708129] sd 0:0:1:0: [sdb] Write Protect is off
[ 13.708129] sd 0:0:1:0: [sdb] Mode Sense: 06 00 00 00
[ 13.708129] sd 0:0:1:0: [sdb] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
[ 13.708129] sdb: sdb1
[ 13.708731] sd 0:0:1:0: [sdb] Attached SCSI removable disk
[ 13.770370] sd 0:0:0:0: Attached scsi generic sg0 type 0
[ 13.770370] sd 0:0:1:0: Attached scsi generic sg1 type 0
[ 13.770370] scsi 0:1:0:0: Attached scsi generic sg2 type 0
[ 13.770370] scsi 0:1:1:0: Attached scsi generic sg3 type 0
[ 13.770370] scsi 0:1:2:0: Attached scsi generic sg4 type 0
[ 13.772174] scsi 0:1:3:0: Attached scsi generic sg5 type 0
[ 13.772313] scsi 0:1:4:0: Attached scsi generic sg6 type 0
[ 13.772432] scsi 0:1:6:0: Attached scsi generic sg7 type 3
[ 14.015900] PM: Starting manual resume from disk
[ 14.035827] kjournald starting. Commit interval 5 seconds
[ 14.035899] EXT3-fs: mounted filesystem with ordered data mode.
[ 14.799395] udevd version 125 started
[ 15.122224] dcdbas dcdbas: Dell Systems Management Base Driver (version 5.6.0-3.2)
[ 15.721715] Linux agpgart interface v0.103
[ 15.900107] piix4_smbus 0000:00:0f.0: Found 0000:00:0f.0 device
[ 15.999801] input: Power Button (FF) as /class/input/input0
[ 16.025724] ACPI: Power Button (FF) [PWRF]
[ 16.839327] pci_hotplug: PCI Hot Plug PCI Core version: 0.5
[ 16.871005] shpchp: Standard Hot Plug PCI Controller Driver version: 0.4
[ 17.064356] input: PC Speaker as /class/input/input1
[ 17.739319] Error: Driver 'pcspkr' is already registered, aborting...
[ 18.055412] Adding 506036k swap on /dev/sda2. Priority:-1 extents:1 across:506036k
[ 18.201732] EXT3 FS on sda5, internal journal
[ 18.365861] loop: module loaded
[ 18.422967] device-mapper: uevent: version 1.0.3
[ 18.422967] device-mapper: ioctl: 4.13.0-ioctl (2007-10-18) initialised: dm-devel@redhat.com
[ 19.302066] kjournald starting. Commit interval 5 seconds
[ 19.302066] EXT3 FS on sda1, internal journal
[ 19.302066] EXT3-fs: mounted filesystem with ordered data mode.
[ 19.302066] kjournald starting. Commit interval 5 seconds
[ 19.302066] EXT3 FS on sda9, internal journal
[ 19.302066] EXT3-fs: mounted filesystem with ordered data mode.
[ 19.354073] SGI XFS with ACLs, security attributes, realtime, large block numbers, no debug enabled
[ 19.354324] SGI XFS Quota Management subsystem
[ 22.528095] XFS mounting filesystem sda10
[ 22.528095] Ending clean XFS mount for filesystem: sda10
[ 22.536474] kjournald starting. Commit interval 5 seconds
[ 22.628955] EXT3 FS on sda6, internal journal
[ 22.628955] EXT3-fs: mounted filesystem with ordered data mode.
[ 22.536474] kjournald starting. Commit interval 5 seconds
[ 22.640955] EXT3 FS on sda8, internal journal
[ 22.640955] EXT3-fs: mounted filesystem with ordered data mode.
[ 22.536474] kjournald starting. Commit interval 5 seconds
[ 22.657131] EXT3 FS on sda7, internal journal
[ 22.657131] EXT3-fs: mounted filesystem with ordered data mode.
[ 24.433364] NET: Registered protocol family 10
[ 24.433364] lo: Disabled Privacy Extensions
[ 24.433364] ADDRCONF(NETDEV_UP): eth0: link is not ready
[ 25.982589] tg3: eth0: Link is up at 1000 Mbps, full duplex.
[ 25.982589] tg3: eth0: Flow control is off for TX and off for RX.
[ 25.982589] ADDRCONF(NETDEV_CHANGE): eth0: link becomes ready
[ 36.773307] eth0: no IPv6 routers present
** Loaded modules:
Module Size Used by
ipv6 235300 24
xfs 458072 1
dm_snapshot 14340 0
dm_mirror 15104 0
dm_log 8452 1 dm_mirror
dm_mod 46184 3 dm_snapshot,dm_mirror,dm_log
loop 12748 0
snd_pcm 62596 0
evdev 8000 0
snd_timer 17800 1 snd_pcm
snd 45604 2 snd_pcm,snd_timer
soundcore 6368 1 snd
snd_page_alloc 7816 1 snd_pcm
psmouse 32336 0
serio_raw 4740 0
pcspkr 2432 0
shpchp 25528 0
pci_hotplug 23460 1 shpchp
button 6096 0
i2c_piix4 7216 0
i2c_core 19828 1 i2c_piix4
sworks_agp 6720 0
agpgart 28776 1 sworks_agp
dcdbas 6272 0
ext3 105512 6
jbd 39444 1 ext3
mbcache 7108 1 ext3
sg 26964 0
sd_mod 22200 9
ide_cd_mod 27652 0
cdrom 30176 1 ide_cd_mod
ata_generic 4676 0
libata 140384 1 ata_generic
dock 8304 1 libata
aacraid 57388 8
floppy 47716 0
scsi_mod 129356 4 sg,sd_mod,libata,aacraid
tg3 84708 0
ohci_hcd 18500 0
usbcore 118160 2 ohci_hcd
serverworks 4932 0 [permanent]
ide_pci_generic 3908 0 [permanent]
ide_core 96168 3 ide_cd_mod,serverworks,ide_pci_generic
thermal 15228 0
processor 32576 1 thermal
fan 4164 0
thermal_sys 10856 3 thermal,processor,fan
** PCI devices:
00:00.0 Host bridge [0600]: Broadcom CMIC-LE Host Bridge (GC-LE chipset) [1166:0014] (rev 33)
Control: I/O- Mem- BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap- 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Kernel modules: sworks-agp
00:00.1 Host bridge [0600]: Broadcom CMIC-LE Host Bridge (GC-LE chipset) [1166:0014]
Control: I/O- Mem- BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap- 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Kernel modules: sworks-agp
00:00.2 Host bridge [0600]: Broadcom CMIC-LE Host Bridge (GC-LE chipset) [1166:0014]
Control: I/O- Mem- BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap- 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Kernel modules: sworks-agp
00:04.0 Class [ff00]: Dell Embedded Remote Access or ERA/O [1028:000c]
Subsystem: Dell Embedded Remote Access or ERA/O [1028:000c]
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV+ VGASnoop- ParErr- Stepping- SERR+ FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 32, Cache Line Size: 64 bytes
Interrupt: pin A routed to IRQ 11
Region 0: Memory at feb80000 (32-bit, prefetchable) [size=4K]
Region 1: I/O ports at ecf8 [size=8]
Region 2: I/O ports at ece8 [size=8]
Expansion ROM at fe000000 [disabled] [size=64K]
Capabilities: <access denied>
00:04.1 Class [ff00]: Dell Remote Access Card III [1028:0008]
Subsystem: Dell Remote Access Card III [1028:0008]
Control: I/O+ Mem+ BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR+ FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Interrupt: pin B routed to IRQ 23
Region 0: Memory at fe102000 (32-bit, non-prefetchable) [size=4K]
Region 1: I/O ports at ec80 [size=64]
Region 2: Memory at feb00000 (32-bit, prefetchable) [size=512K]
Capabilities: <access denied>
Kernel driver in use: serial
00:04.2 Class [ff00]: Dell Embedded Remote Access: BMC/SMIC device [1028:000d]
Subsystem: Dell Embedded Remote Access: BMC/SMIC device [1028:000d]
Control: I/O+ Mem+ BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR+ FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Interrupt: pin C routed to IRQ 7
Region 0: I/O ports at ecf4 [size=4]
Capabilities: <access denied>
00:0e.0 VGA compatible controller [0300]: ATI Technologies Inc Rage XL [1002:4752] (rev 27) (prog-if 00 [VGA controller])
Subsystem: Dell Device [1028:0121]
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop+ ParErr- Stepping+ SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 32 (2000ns min), Cache Line Size: 64 bytes
Region 0: Memory at fd000000 (32-bit, non-prefetchable) [size=16M]
Region 1: I/O ports at e800 [size=256]
Region 2: Memory at fe101000 (32-bit, non-prefetchable) [size=4K]
[virtual] Expansion ROM at c0000000 [disabled] [size=128K]
Capabilities: <access denied>
00:0f.0 Host bridge [0600]: Broadcom CSB5 South Bridge [1166:0201] (rev 93)
Subsystem: Broadcom CSB5 South Bridge [1166:0201]
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr+ Stepping- SERR+ FastB2B- DisINTx-
Status: Cap- 66MHz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort+ >SERR- <PERR- INTx-
Latency: 32
Kernel driver in use: piix4_smbus
Kernel modules: i2c-piix4, sworks-agp
00:0f.1 IDE interface [0101]: Broadcom CSB5 IDE Controller [1166:0212] (rev 93) (prog-if 82 [Master PriP])
Subsystem: Broadcom CSB5 IDE Controller [1166:0212]
Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr+ Stepping- SERR+ FastB2B- DisINTx-
Status: Cap- 66MHz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 64
Region 0: I/O ports at 01f0 [size=8]
Region 1: I/O ports at 03f4 [size=1]
Region 2: I/O ports at 0170 [size=8]
Region 3: I/O ports at 0374 [size=1]
Region 4: I/O ports at 08b0 [size=16]
Kernel driver in use: Serverworks_IDE
Kernel modules: serverworks
00:0f.2 USB Controller [0c03]: Broadcom OSB4/CSB5 OHCI USB Controller [1166:0220] (rev 05) (prog-if 10 [OHCI])
Subsystem: Broadcom OSB4/CSB5 OHCI USB Controller [1166:0220]
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV+ VGASnoop- ParErr+ Stepping- SERR+ FastB2B- DisINTx-
Status: Cap- 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 32 (20000ns max)
Interrupt: pin A routed to IRQ 11
Region 0: Memory at fe100000 (32-bit, non-prefetchable) [size=4K]
Kernel driver in use: ohci_hcd
Kernel modules: ohci-hcd
00:0f.3 ISA bridge [0601]: Broadcom CSB5 LPC bridge [1166:0225]
Subsystem: Broadcom Device [1166:0230]
Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap- 66MHz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0
00:10.0 Host bridge [0600]: Broadcom CIOB-X2 PCI-X I/O Bridge [1166:0101] (rev 05)
Control: I/O- Mem+ BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr+ Stepping- SERR+ FastB2B- DisINTx-
Status: Cap+ 66MHz+ UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort+ >SERR- <PERR- INTx-
Capabilities: <access denied>
Kernel modules: sworks-agp
00:10.2 Host bridge [0600]: Broadcom CIOB-X2 PCI-X I/O Bridge [1166:0101] (rev 05)
Control: I/O- Mem+ BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr+ Stepping- SERR+ FastB2B- DisINTx-
Status: Cap+ 66MHz+ UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort+ >SERR- <PERR- INTx-
Capabilities: <access denied>
Kernel modules: sworks-agp
00:11.0 Host bridge [0600]: Broadcom CIOB-X2 PCI-X I/O Bridge [1166:0101] (rev 05)
Control: I/O- Mem+ BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr+ Stepping- SERR+ FastB2B- DisINTx-
Status: Cap+ 66MHz+ UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort+ >SERR- <PERR- INTx-
Capabilities: <access denied>
Kernel modules: sworks-agp
00:11.2 Host bridge [0600]: Broadcom CIOB-X2 PCI-X I/O Bridge [1166:0101] (rev 05)
Control: I/O- Mem+ BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr+ Stepping- SERR+ FastB2B- DisINTx-
Status: Cap+ 66MHz+ UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort+ >SERR- <PERR- INTx-
Capabilities: <access denied>
Kernel modules: sworks-agp
03:06.0 Ethernet controller [0200]: Broadcom Corporation NetXtreme BCM5703X Gigabit Ethernet [14e4:16a7] (rev 02)
Subsystem: Dell Device [1028:0121]
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR+ FastB2B- DisINTx-
Status: Cap+ 66MHz+ UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 64 (16000ns min), Cache Line Size: 64 bytes
Interrupt: pin A routed to IRQ 28
Region 0: Memory at fcf10000 (64-bit, non-prefetchable) [size=64K]
Capabilities: <access denied>
Kernel driver in use: tg3
Kernel modules: tg3
03:08.0 Ethernet controller [0200]: Broadcom Corporation NetXtreme BCM5703X Gigabit Ethernet [14e4:16a7] (rev 02)
Subsystem: Dell Device [1028:0121]
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR+ FastB2B- DisINTx-
Status: Cap+ 66MHz+ UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 64 (16000ns min), Cache Line Size: 64 bytes
Interrupt: pin A routed to IRQ 29
Region 0: Memory at fcf00000 (64-bit, non-prefetchable) [size=64K]
Capabilities: <access denied>
Kernel driver in use: tg3
Kernel modules: tg3
04:08.0 PCI bridge [0604]: Intel Corporation 80303 I/O Processor PCI-to-PCI Bridge [8086:0309] (rev 01) (prog-if 00 [Normal decode])
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR+ FastB2B- DisINTx-
Status: Cap+ 66MHz+ UDF- FastB2B+ ParErr- DEVSEL=slow >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 32, Cache Line Size: 64 bytes
Bus: primary=04, secondary=05, subordinate=05, sec-latency=32
Secondary status: 66MHz+ FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort+ <SERR- <PERR-
BridgeCtl: Parity- SERR+ NoISA+ VGA- MAbort- >Reset- FastB2B-
PriDiscTmr- SecDiscTmr- DiscTmrStat- DiscTmrSERREn-
Capabilities: <access denied>
Kernel modules: shpchp
04:08.1 RAID bus controller [0104]: Dell PowerEdge Expandable RAID Controller 3/Di [1028:000a] (rev 01)
Subsystem: Dell PERC 3/DiB [Boxster] [1028:0121]
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV+ VGASnoop- ParErr- Stepping- SERR+ FastB2B- DisINTx-
Status: Cap+ 66MHz+ UDF- FastB2B+ ParErr- DEVSEL=slow >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 32, Cache Line Size: 64 bytes
Interrupt: pin A routed to IRQ 30
Region 0: Memory at f0000000 (32-bit, prefetchable) [size=128M]
Expansion ROM at fcd00000 [disabled] [size=64K]
Capabilities: <access denied>
Kernel driver in use: aacraid
Kernel modules: aacraid
-- System Information:
Debian Release: 5.0
APT prefers stable
APT policy: (500, 'stable')
Architecture: i386 (i686)
Kernel: Linux 2.6.26-1-686 (SMP w/2 CPU cores)
Locale: LANG=en_CA.UTF-8, LC_CTYPE=en_CA.UTF-8 (charmap=UTF-8)
Shell: /bin/sh linked to /bin/bash
Versions of packages linux-image-2.6.26-1-686 depends on:
ii debconf [debconf-2.0] 1.5.24 Debian configuration management sy
ii initramfs-tools [linux-initra 0.92o tools for generating an initramfs
ii module-init-tools 3.4-1 tools for managing Linux kernel mo
Versions of packages linux-image-2.6.26-1-686 recommends:
ii libc6-i686 2.7-18 GNU C Library: Shared libraries [i
Versions of packages linux-image-2.6.26-1-686 suggests:
ii grub 0.97-47lenny2 GRand Unified Bootloader (Legacy v
pn linux-doc-2.6.26 <none> (no description available)
-- debconf information:
linux-image-2.6.26-1-686/preinst/abort-overwrite-2.6.26-1-686:
shared/kernel-image/really-run-bootloader: true
linux-image-2.6.26-1-686/postinst/bootloader-error-2.6.26-1-686:
linux-image-2.6.26-1-686/postinst/depmod-error-initrd-2.6.26-1-686: false
linux-image-2.6.26-1-686/prerm/removing-running-kernel-2.6.26-1-686: true
linux-image-2.6.26-1-686/postinst/old-system-map-link-2.6.26-1-686: true
linux-image-2.6.26-1-686/preinst/abort-install-2.6.26-1-686:
linux-image-2.6.26-1-686/preinst/lilo-has-ramdisk:
linux-image-2.6.26-1-686/preinst/bootloader-initrd-2.6.26-1-686: true
linux-image-2.6.26-1-686/prerm/would-invalidate-boot-loader-2.6.26-1-686: true
linux-image-2.6.26-1-686/preinst/elilo-initrd-2.6.26-1-686: true
linux-image-2.6.26-1-686/postinst/kimage-is-a-directory:
linux-image-2.6.26-1-686/postinst/old-dir-initrd-link-2.6.26-1-686: true
linux-image-2.6.26-1-686/postinst/create-kimage-link-2.6.26-1-686: true
linux-image-2.6.26-1-686/preinst/lilo-initrd-2.6.26-1-686: true
linux-image-2.6.26-1-686/postinst/old-initrd-link-2.6.26-1-686: true
linux-image-2.6.26-1-686/preinst/overwriting-modules-2.6.26-1-686: true
linux-image-2.6.26-1-686/postinst/depmod-error-2.6.26-1-686: false
linux-image-2.6.26-1-686/postinst/bootloader-test-error-2.6.26-1-686:
linux-image-2.6.26-1-686/preinst/failed-to-move-modules-2.6.26-1-686:
linux-image-2.6.26-1-686/preinst/initrd-2.6.26-1-686:
--
Chris Quirk, System Administrator
marblemedia
74 FRASER AVENUE, SUITE 200 - TORONTO, ON - M6K 3E1 - T. 416.646.2711
ext 246 - TTY. 416.645.0436 - F. 416.646.2717
--- End Message ---