Bug#709278: linux-image-3.2.0-4-686-pae: 3.2.41-2 break X on Intel Atom and freeze when DisplayLink USB VGA attached
Package: src:linux
Version: 3.2.39-2
Severity: normal
Dear Maintainer,
This kernel works on my hardware, but 3.2.41-2+deb7u2 does not. I use Intel
Atom CPU D2700 with VGA compatible controller: Intel Corporation Atom
Processor D2xxx/N2xxx Integrated Graphics Controller (rev 09) and DisplayLink
USB Graphics Controller ID 17e9:0199.
When USB device connected the boot freeze while waiting /dev to fully
populated.
When USB device disconnected, the boot completed but the resolution limited to
1280x768 instead of 1280x1024. My monitors are Neovo F-419 with 1280x1024
resolution and DVI input.
-- Package-specific info:
** Version:
Linux version 3.2.0-4-686-pae (debian-kernel@lists.debian.org) (gcc version
4.6.3 (Debian 4.6.3-15) ) #1 SMP Debian 3.2.39-2
** Command line:
BOOT_IMAGE=/boot/vmlinuz-3.2.0-4-686-pae root=UUID=59ad45b3-c595-4710-a1af-
f873f21eb690 ro quiet
** Not tainted
** Kernel log:
[ 3.066695] usb 1-3.1: Manufacturer: DisplayLink
[ 3.066701] usb 1-3.1: SerialNumber: SD101578
[ 3.142649] usb 1-3.2: new full-speed USB device number 6 using ehci_hcd
[ 3.174124] input: Power Button as
/devices/LNXSYSTM:00/LNXSYBUS:00/PNP0C0C:00/input/input2
[ 3.174140] ACPI: Power Button [PWRB]
[ 3.174323] input: Sleep Button as
/devices/LNXSYSTM:00/LNXSYBUS:00/PNP0C0E:00/input/input3
[ 3.174335] ACPI: Sleep Button [SLPB]
[ 3.174504] input: Power Button as
/devices/LNXSYSTM:00/LNXPWRBN:00/input/input4
[ 3.174542] ACPI: Power Button [PWRF]
[ 3.181127] udlfb: DisplayLink USB Adapter - serial #SD101578
[ 3.181137] udlfb: vid_17e9&pid_0199&rev_0108 driver's dlfb_data struct at
f71a2000
[ 3.181143] udlfb: console enable=1
[ 3.181147] udlfb: fb_defio enable=1
[ 3.181150] udlfb: shadow enable=1
[ 3.181355] udlfb: vendor descriptor length:22 data:22 5f 01 0020 05 00 01
03 04 02
[ 3.181362] udlfb: DL chip limited to 2080000 pixel modes
[ 3.182122] udlfb: allocated 4 65024 byte urbs
[ 3.184272] iTCO_vendor_support: vendor-support=0
[ 3.186017] iTCO_wdt: Intel TCO WatchDog Timer Driver v1.07
[ 3.186237] iTCO_wdt: Found a NM10 TCO device (Version=2, TCOBASE=0x0460)
[ 3.186386] iTCO_wdt: initialized. heartbeat=30 sec (nowayout=0)
[ 3.235597] usb 1-3.2: New USB device found, idVendor=0d8c, idProduct=0008
[ 3.235607] usb 1-3.2: New USB device strings: Mfr=0, Product=1,
SerialNumber=0
[ 3.235614] usb 1-3.2: Product: C-Media USB Audio Device
[ 3.237790] input: C-Media USB Audio Device as
/devices/pci0000:00/0000:00:1d.7/usb1/1-3/1-3.2/1-3.2:1.3/input/input5
[ 3.237957] generic-usb 0003:0D8C:0008.0003: input,hidraw2: USB HID v1.00
Device [C-Media USB Audio Device ] on usb-0000:00:1d.7-3.2/input3
[ 3.242841] snd_hda_intel 0000:00:1b.0: irq 45 for MSI/MSI-X
[ 3.242898] snd_hda_intel 0000:00:1b.0: setting latency timer to 64
[ 3.272518] udlfb: 1280x1024 valid mode
[ 3.272526] udlfb: 720x400 valid mode
[ 3.272531] udlfb: 640x480 valid mode
[ 3.272536] udlfb: 640x480 valid mode
[ 3.272540] udlfb: 640x480 valid mode
[ 3.272545] udlfb: 640x480 valid mode
[ 3.272550] udlfb: 800x600 valid mode
[ 3.272555] udlfb: 800x600 valid mode
[ 3.272560] udlfb: 800x600 valid mode
[ 3.272565] udlfb: 800x600 valid mode
[ 3.272570] udlfb: 832x624 valid mode
[ 3.272575] udlfb: 1024x768 valid mode
[ 3.272580] udlfb: 1024x768 valid mode
[ 3.272585] udlfb: 1024x768 valid mode
[ 3.272590] udlfb: 1280x1024 valid mode
[ 3.272594] udlfb: 1280x1024 valid mode
[ 3.272600] udlfb: Reallocating framebuffer. Addresses will change!
[ 3.277390] udlfb: 1280x1024 valid mode
[ 3.277396] udlfb: set_par mode 1280x1024
[ 3.298629] udlfb: open /dev/fb0 user=0 fb_info=f3be3800 count=1
[ 3.300840] udlfb: set_par mode 1280x1024
[ 3.304588] input: PC Speaker as /devices/platform/pcspkr/input/input6
[ 3.306792] coretemp coretemp.0: Unable to read TjMax from CPU 0
[ 3.306813] coretemp coretemp.0: Using relative temperature scale!
[ 3.306841] coretemp coretemp.0: Unable to read TjMax from CPU 2
[ 3.306861] coretemp coretemp.0: Using relative temperature scale!
[ 3.320383] input: HDA Digital PCBeep as
/devices/pci0000:00/0000:00:1b.0/input/input7
[ 3.321600] HDMI status: Codec=1 Pin=3 Presence_Detect=0 ELD_Valid=0
[ 3.325623] input: HDA Intel HDMI/DP,pcm=3 as
/devices/pci0000:00/0000:00:1b.0/sound/card0/input8
[ 3.326406] input: HDA Intel Headphone as
/devices/pci0000:00/0000:00:1b.0/sound/card0/input9
[ 3.336319] Console: switching to colour frame buffer device 160x64
[ 3.337224] udlfb: set_par mode 1280x1024
[ 3.347011] udlfb: DisplayLink USB device /dev/fb0 attached. 1280x1024
resolution. Using 5120K framebuffer memory
[ 3.347069] usbcore: registered new interface driver udlfb
[ 3.430940] usbcore: registered new interface driver snd-usb-audio
[ 3.955969] Adding 3605500k swap on /dev/sda5. Priority:-1 extents:1
across:3605500k SS
[ 3.982386] EXT4-fs (sda1): re-mounted. Opts: (null)
[ 4.038352] EXT4-fs (sda1): re-mounted. Opts: errors=remount-ro
[ 4.080480] loop: module loaded
[ 5.230481] RPC: Registered named UNIX socket transport module.
[ 5.230487] RPC: Registered udp transport module.
[ 5.230491] RPC: Registered tcp transport module.
[ 5.230494] RPC: Registered tcp NFSv4.1 backchannel transport module.
[ 5.241272] FS-Cache: Loaded
[ 5.259065] FS-Cache: Netfs 'nfs' registered for caching
[ 5.268395] Installing knfsd (copyright (C) 1996 okir@monad.swb.de).
[ 5.565722] udlfb: set_par mode 1280x1024
[ 6.477325] Bluetooth: Core ver 2.16
[ 6.477407] NET: Registered protocol family 31
[ 6.477413] Bluetooth: HCI device and connection manager initialized
[ 6.477421] Bluetooth: HCI socket layer initialized
[ 6.477426] Bluetooth: L2CAP socket layer initialized
[ 6.477440] Bluetooth: SCO socket layer initialized
[ 6.515724] Bluetooth: RFCOMM TTY layer initialized
[ 6.515740] Bluetooth: RFCOMM socket layer initialized
[ 6.515746] Bluetooth: RFCOMM ver 1.11
[ 6.536283] Bluetooth: BNEP (Ethernet Emulation) ver 1.3
[ 6.536292] Bluetooth: BNEP filters: protocol multicast
[ 6.766094] ADDRCONF(NETDEV_UP): eth0: link is not ready
[ 8.989433] lp: driver loaded but no devices found
[ 9.021710] ppdev: user-space parallel port driver
[ 9.174390] udlfb: set_par mode 1280x1024
[ 9.191549] udlfb: open /dev/fb0 user=1 fb_info=f3be3800 count=2
[ 9.191566] udlfb: released /dev/fb0 user=1 count=1
[ 9.635343] udlfb: open /dev/fb0 user=1 fb_info=f3be3800 count=2
[ 9.635368] udlfb: open /dev/fb0 user=1 fb_info=f3be3800 count=3
[ 9.880618] e1000e: eth0 NIC Link is Up 1000 Mbps Full Duplex, Flow Control:
None
[ 9.881081] ADDRCONF(NETDEV_CHANGE): eth0: link becomes ready
[ 10.283000] udlfb: /dev/fb0 FB_BLANK mode 0 --> 0
[ 19.999017] eth0: no IPv6 routers present
[ 26.633023] udlfb: /dev/fb0 FB_BLANK mode 0 --> 0
[ 26.904583] udlfb: /dev/fb0 FB_BLANK mode 0 --> 0
** Model information
not available
** Loaded modules:
parport_pc
ppdev
lp
parport
bnep
rfcomm
bluetooth
rfkill
binfmt_misc
nfsd
nfs
nfs_acl
auth_rpcgss
fscache
lockd
sunrpc
loop
snd_usb_audio
snd_usbmidi_lib
snd_seq_midi
snd_seq_midi_event
snd_rawmidi
snd_hda_codec_realtek
coretemp
pcspkr
snd_hda_codec_hdmi
psmouse
serio_raw
i2c_i801
i2c_core
evdev
snd_hda_intel
snd_hda_codec
snd_hwdep
snd_pcm
snd_page_alloc
snd_seq
snd_seq_device
snd_timer
video
snd
iTCO_wdt
iTCO_vendor_support
soundcore
udlfb
button
processor
thermal_sys
ext4
crc16
jbd2
mbcache
usbhid
hid
sg
sd_mod
crc_t10dif
ahci
libahci
uhci_hcd
libata
e1000e
ehci_hcd
scsi_mod
usbcore
usb_common
** PCI devices:
00:00.0 Host bridge [0600]: Intel Corporation Atom Processor D2xxx/N2xxx DRAM
Controller [8086:0bf3] (rev 03)
Subsystem: Intel Corporation Device [8086:2011]
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B- DisINTx-
Status: Cap- 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort-
<MAbort- >SERR- <PERR- INTx-
Latency: 0
00:02.0 VGA compatible controller [0300]: Intel Corporation Atom Processor
D2xxx/N2xxx Integrated Graphics Controller [8086:0be2] (rev 09) (prog-if 00
[VGA controller])
Subsystem: Intel Corporation Device [8086:2011]
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort-
<MAbort- >SERR- <PERR- INTx-
Latency: 0
Interrupt: pin A routed to IRQ 11
Region 0: Memory at c0100000 (32-bit, non-prefetchable) [size=1M]
Region 1: I/O ports at 20d0 [size=8]
Expansion ROM at <unassigned> [disabled]
Capabilities: <access denied>
00:1b.0 Audio device [0403]: Intel Corporation NM10/ICH7 Family High Definition
Audio Controller [8086:27d8] (rev 02)
Subsystem: Intel Corporation Device [8086:2011]
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B- DisINTx+
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort-
<MAbort- >SERR- <PERR- INTx-
Latency: 0, Cache Line Size: 64 bytes
Interrupt: pin A routed to IRQ 45
Region 0: Memory at c0300000 (64-bit, non-prefetchable) [size=16K]
Capabilities: <access denied>
Kernel driver in use: snd_hda_intel
00:1c.0 PCI bridge [0604]: Intel Corporation NM10/ICH7 Family PCI Express Port
1 [8086:27d0] (rev 02) (prog-if 00 [Normal decode])
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B- DisINTx+
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort-
<MAbort- >SERR- <PERR- INTx-
Latency: 0, Cache Line Size: 64 bytes
Bus: primary=00, secondary=01, subordinate=01, sec-latency=0
I/O behind bridge: 00001000-00001fff
Memory behind bridge: c0000000-c00fffff
Prefetchable memory behind bridge: 00000000c0400000-00000000c05fffff
Secondary status: 66MHz- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort-
<MAbort- <SERR- <PERR-
BridgeCtl: Parity- SERR- NoISA+ VGA- MAbort- >Reset- FastB2B-
PriDiscTmr- SecDiscTmr- DiscTmrStat- DiscTmrSERREn-
Capabilities: <access denied>
Kernel driver in use: pcieport
00:1d.0 USB controller [0c03]: Intel Corporation NM10/ICH7 Family USB UHCI
Controller #1 [8086:27c8] (rev 02) (prog-if 00 [UHCI])
Subsystem: Intel Corporation Device [8086:2011]
Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B- DisINTx-
Status: Cap- 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0
Interrupt: pin A routed to IRQ 23
Region 4: I/O ports at 20a0 [size=32]
Kernel driver in use: uhci_hcd
00:1d.1 USB controller [0c03]: Intel Corporation NM10/ICH7 Family USB UHCI
Controller #2 [8086:27c9] (rev 02) (prog-if 00 [UHCI])
Subsystem: Intel Corporation Device [8086:2011]
Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B- DisINTx-
Status: Cap- 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0
Interrupt: pin B routed to IRQ 19
Region 4: I/O ports at 2080 [size=32]
Kernel driver in use: uhci_hcd
00:1d.2 USB controller [0c03]: Intel Corporation NM10/ICH7 Family USB UHCI
Controller #3 [8086:27ca] (rev 02) (prog-if 00 [UHCI])
Subsystem: Intel Corporation Device [8086:2011]
Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B- DisINTx-
Status: Cap- 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0
Interrupt: pin C routed to IRQ 18
Region 4: I/O ports at 2060 [size=32]
Kernel driver in use: uhci_hcd
00:1d.3 USB controller [0c03]: Intel Corporation NM10/ICH7 Family USB UHCI
Controller #4 [8086:27cb] (rev 02) (prog-if 00 [UHCI])
Subsystem: Intel Corporation Device [8086:2011]
Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B- DisINTx-
Status: Cap- 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0
Interrupt: pin D routed to IRQ 16
Region 4: I/O ports at 2040 [size=32]
Kernel driver in use: uhci_hcd
00:1d.7 USB controller [0c03]: Intel Corporation NM10/ICH7 Family USB2 EHCI
Controller [8086:27cc] (rev 02) (prog-if 20 [EHCI])
Subsystem: Intel Corporation Device [8086:2011]
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0
Interrupt: pin A routed to IRQ 23
Region 0: Memory at c0204400 (32-bit, non-prefetchable) [size=1K]
Capabilities: <access denied>
Kernel driver in use: ehci_hcd
00:1e.0 PCI bridge [0604]: Intel Corporation 82801 Mobile PCI Bridge
[8086:2448] (rev e2) (prog-if 01 [Subtractive decode])
Control: I/O- Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR+ FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort-
<MAbort- >SERR- <PERR- INTx-
Latency: 0
Bus: primary=00, secondary=02, subordinate=02, sec-latency=32
Secondary status: 66MHz- FastB2B+ ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort+ <SERR- <PERR-
BridgeCtl: Parity- SERR- NoISA+ VGA- MAbort- >Reset- FastB2B-
PriDiscTmr- SecDiscTmr- DiscTmrStat- DiscTmrSERREn-
Capabilities: <access denied>
00:1f.0 ISA bridge [0601]: Intel Corporation NM10 Family LPC Controller
[8086:27bc] (rev 02)
Subsystem: Intel Corporation Device [8086:2011]
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR+ FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0
Capabilities: <access denied>
00:1f.2 SATA controller [0106]: Intel Corporation NM10/ICH7 Family SATA
Controller [AHCI mode] [8086:27c1] (rev 02) (prog-if 01 [AHCI 1.0])
Subsystem: Intel Corporation Device [8086:2011]
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B- DisINTx+
Status: Cap+ 66MHz+ UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0
Interrupt: pin B routed to IRQ 44
Region 0: I/O ports at 20c8 [size=8]
Region 1: I/O ports at 20dc [size=4]
Region 2: I/O ports at 20c0 [size=8]
Region 3: I/O ports at 20d8 [size=4]
Region 4: I/O ports at 2020 [size=16]
Region 5: Memory at c0204000 (32-bit, non-prefetchable) [size=1K]
Capabilities: <access denied>
Kernel driver in use: ahci
00:1f.3 SMBus [0c05]: Intel Corporation NM10/ICH7 Family SMBus Controller
[8086:27da] (rev 02)
Subsystem: Intel Corporation Device [8086:2011]
Control: I/O+ Mem- BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B- DisINTx-
Status: Cap- 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR- INTx-
Interrupt: pin B routed to IRQ 19
Region 4: I/O ports at 2000 [size=32]
Kernel driver in use: i801_smbus
01:00.0 Ethernet controller [0200]: Intel Corporation 82574L Gigabit Network
Connection [8086:10d3]
Subsystem: Intel Corporation Device [8086:2011]
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B- DisINTx+
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort-
<MAbort- >SERR- <PERR- INTx-
Latency: 0, Cache Line Size: 64 bytes
Interrupt: pin A routed to IRQ 16
Region 0: Memory at c0020000 (32-bit, non-prefetchable) [size=128K]
Region 1: Memory at c0000000 (32-bit, non-prefetchable) [size=128K]
Region 2: I/O ports at 1000 [size=32]
Region 3: Memory at c0040000 (32-bit, non-prefetchable) [size=16K]
Capabilities: <access denied>
Kernel driver in use: e1000e
** USB devices:
Bus 001 Device 001: ID 1d6b:0002 Linux Foundation 2.0 root hub
Bus 002 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub
Bus 003 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub
Bus 004 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub
Bus 005 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub
Bus 001 Device 002: ID 1a40:0101 Terminus Technology Inc. 4-Port HUB
Bus 004 Device 002: ID 413c:2003 Dell Computer Corp. Keyboard
Bus 004 Device 003: ID 046d:c03e Logitech, Inc. Premium Optical Wheel Mouse (M-BT58)
Bus 001 Device 005: ID 17e9:0199 DisplayLink
Bus 001 Device 006: ID 0d8c:0008 C-Media Electronics, Inc.
-- System Information:
Debian Release: 7.0
APT prefers stable
APT policy: (500, 'stable')
Architecture: i386 (i686)
Kernel: Linux 3.2.0-4-686-pae (SMP w/4 CPU cores)
Locale: LANG=hu_HU.UTF-8, LC_CTYPE=hu_HU.UTF-8 (charmap=UTF-8)
Shell: /bin/sh linked to /bin/dash
Versions of packages linux-image-3.2.0-4-686-pae depends on:
ii debconf [debconf-2.0] 1.5.49
ii initramfs-tools [linux-initramfs-tool] 0.109.1
ii kmod 9-3
ii linux-base 3.5
ii module-init-tools 9-3
Versions of packages linux-image-3.2.0-4-686-pae recommends:
ii firmware-linux-free 3.2
ii libc6-i686 2.13-38
Versions of packages linux-image-3.2.0-4-686-pae suggests:
pn debian-kernel-handbook <none>
ii grub-pc 1.99-27+deb7u1
pn linux-doc-3.2 <none>
Versions of packages linux-image-3.2.0-4-686-pae is related to:
pn firmware-atheros <none>
pn firmware-bnx2 <none>
pn firmware-bnx2x <none>
pn firmware-brcm80211 <none>
pn firmware-intelwimax <none>
pn firmware-ipw2x00 <none>
pn firmware-ivtv <none>
pn firmware-iwlwifi <none>
pn firmware-libertas <none>
pn firmware-linux <none>
pn firmware-linux-nonfree <none>
pn firmware-myricom <none>
pn firmware-netxen <none>
pn firmware-qlogic <none>
pn firmware-ralink <none>
pn firmware-realtek <none>
pn xen-hypervisor <none>
-- debconf information:
linux-image-3.2.0-4-686-pae/postinst/depmod-error-initrd-3.2.0-4-686-pae: false
linux-image-3.2.0-4-686-pae/prerm/removing-running-kernel-3.2.0-4-686-pae: true
linux-image-3.2.0-4-686-pae/postinst/ignoring-ramdisk:
linux-image-3.2.0-4-686-pae/postinst/missing-firmware-3.2.0-4-686-pae:
Reply to: