Bug#708757: linux-image-3.2.0-4-amd64: via-rhine network card fails to initialise correctly
On Wed, 22 May 2013 12:31:05 PM Ben Hutchings wrote:
> On Wed, 2013-05-22 at 11:47 +1000, Mark Berndt wrote:
> > Hi Ben, I contacted Intel and they asked me to check if it works under
> > windows. And it does.
>
> OK, so this should be fixable in Linux!
>
> > It would seem it is an issue with the via-rhine driver - where do I take
> > the issue next?
>
> Or it could be a problem with PCI setup. I don't see anything wrong
> with what the driver's doing. (But then, I don't see anything wrong
> with the PCI configuration either.)
>
> > These Intel mini-itx boards are a great low power router platform with
> > significant processing power. There are also lots of them around. The
> > same problem is reported under bsd with the earlier D525 board.
> >
> > Do you think it is really worthwhile following this up?
>
> Does Linux 3.8 (linux-image-3.8-2-amd64 package in unstable) work any
> better?
>
> Please send the contents of /proc/ioports when running Linux 3.2 (and
> 3.8, if that works better).
>
> Ben.
clean install of squeeze for 2.6 files. Upgrade to wheezy for 3.2 files.
Upgrade to unstable for 3.8 files. 3.8 kernel shows same problem.
Cheers
Mark
[ 0.000000] Initializing cgroup subsys cpuset
[ 0.000000] Initializing cgroup subsys cpu
[ 0.000000] Linux version 2.6.32-5-amd64 (Debian 2.6.32-48squeeze3) (dannf@debian.org) (gcc version 4.3.5 (Debian 4.3.5-4) ) #1 SMP Fri May 10 08:43:19 UTC 2013
[ 0.000000] Command line: BOOT_IMAGE=/boot/vmlinuz-2.6.32-5-amd64 root=UUID=54290ac6-2db5-424b-8cdb-e54f7e644b70 ro quiet
[ 0.000000] KERNEL supported cpus:
[ 0.000000] Intel GenuineIntel
[ 0.000000] AMD AuthenticAMD
[ 0.000000] Centaur CentaurHauls
[ 0.000000] BIOS-provided physical RAM map:
[ 0.000000] BIOS-e820: 0000000000000000 - 000000000008f000 (usable)
[ 0.000000] BIOS-e820: 000000000008f000 - 0000000000090000 (reserved)
[ 0.000000] BIOS-e820: 0000000000090000 - 000000000009e800 (usable)
[ 0.000000] BIOS-e820: 000000000009e800 - 00000000000a0000 (reserved)
[ 0.000000] BIOS-e820: 00000000000e0000 - 0000000000100000 (reserved)
[ 0.000000] BIOS-e820: 0000000000100000 - 000000007ee98000 (usable)
[ 0.000000] BIOS-e820: 000000007ee98000 - 000000007eebf000 (reserved)
[ 0.000000] BIOS-e820: 000000007eebf000 - 000000007eeff000 (usable)
[ 0.000000] BIOS-e820: 000000007eeff000 - 000000007efbf000 (ACPI NVS)
[ 0.000000] BIOS-e820: 000000007efbf000 - 000000007eff2000 (usable)
[ 0.000000] BIOS-e820: 000000007eff2000 - 000000007efff000 (ACPI data)
[ 0.000000] BIOS-e820: 000000007efff000 - 000000007f000000 (usable)
[ 0.000000] BIOS-e820: 000000007f000000 - 0000000080000000 (reserved)
[ 0.000000] BIOS-e820: 00000000e0000000 - 00000000e4000000 (reserved)
[ 0.000000] BIOS-e820: 00000000ffe00000 - 0000000100000000 (reserved)
[ 0.000000] DMI 2.7 present.
[ 0.000000] last_pfn = 0x7f000 max_arch_pfn = 0x400000000
[ 0.000000] MTRR default type: uncachable
[ 0.000000] MTRR fixed ranges enabled:
[ 0.000000] 00000-9FFFF write-back
[ 0.000000] A0000-BFFFF uncachable
[ 0.000000] C0000-DFFFF write-protect
[ 0.000000] E0000-FFFFF uncachable
[ 0.000000] MTRR variable ranges enabled:
[ 0.000000] 0 base 000000000 mask F80000000 write-back
[ 0.000000] 1 base 07F000000 mask FFF000000 uncachable
[ 0.000000] 2 base 0FFE00000 mask FFFE00000 write-protect
[ 0.000000] 3 disabled
[ 0.000000] 4 disabled
[ 0.000000] 5 disabled
[ 0.000000] 6 disabled
[ 0.000000] x86 PAT enabled: cpu 0, old 0x7040600070406, new 0x7010600070106
[ 0.000000] initial memory mapped : 0 - 20000000
[ 0.000000] init_memory_mapping: 0000000000000000-000000007f000000
[ 0.000000] 0000000000 - 007f000000 page 2M
[ 0.000000] kernel direct mapping tables up to 7f000000 @ 8000-b000
[ 0.000000] RAMDISK: 3770b000 - 37fef452
[ 0.000000] ACPI: RSDP 00000000000f2390 00024 (v02 INTEL )
[ 0.000000] ACPI: XSDT 000000007effe120 0004C (v01 INTEL TIANO 0000004B 01000013)
[ 0.000000] ACPI: FACP 000000007eff6000 000F4 (v03 INTEL TIANO 0000004B MSFT 0100000D)
[ 0.000000] ACPI: DSDT 000000007eff8000 05B38 (v02 INTEL TIANO 0000004B MSFT 0100000D)
[ 0.000000] ACPI: FACS 000000007ef85000 00040
[ 0.000000] ACPI: SSDT 000000007eff7000 0043E (v01 INTEL TIANO 0000004B MSFT 0100000D)
[ 0.000000] ACPI: APIC 000000007eff5000 00084 (v02 INTEL TIANO 0000004B MSFT 0100000D)
[ 0.000000] ACPI: MCFG 000000007eff4000 0003C (v01 INTEL TIANO 0000004B MSFT 0100000D)
[ 0.000000] ACPI: HPET 000000007eff3000 00038 (v01 INTEL TIANO 0000004B MSFT 0100000D)
[ 0.000000] ACPI: Local APIC address 0xfee00000
[ 0.000000] No NUMA configuration found
[ 0.000000] Faking a node at 0000000000000000-000000007f000000
[ 0.000000] Bootmem setup node 0 0000000000000000-000000007f000000
[ 0.000000] NODE_DATA [0000000000009000 - 0000000000010fff]
[ 0.000000] bootmap [0000000000011000 - 0000000000020dff] pages 10
[ 0.000000] (7 early reservations) ==> bootmem [0000000000 - 007f000000]
[ 0.000000] #0 [0000000000 - 0000001000] BIOS data page ==> [0000000000 - 0000001000]
[ 0.000000] #1 [0000006000 - 0000008000] TRAMPOLINE ==> [0000006000 - 0000008000]
[ 0.000000] #2 [0001000000 - 00016db584] TEXT DATA BSS ==> [0001000000 - 00016db584]
[ 0.000000] #3 [003770b000 - 0037fef452] RAMDISK ==> [003770b000 - 0037fef452]
[ 0.000000] #4 [000009e800 - 0000100000] BIOS reserved ==> [000009e800 - 0000100000]
[ 0.000000] #5 [00016dc000 - 00016dc1ba] BRK ==> [00016dc000 - 00016dc1ba]
[ 0.000000] #6 [0000008000 - 0000009000] PGTABLE ==> [0000008000 - 0000009000]
[ 0.000000] found SMP MP-table at [ffff8800000fbe40] fbe40
[ 0.000000] [ffffea0000000000-ffffea0001bfffff] PMD -> [ffff880001c00000-ffff8800037fffff] on node 0
[ 0.000000] Zone PFN ranges:
[ 0.000000] DMA 0x00000000 -> 0x00001000
[ 0.000000] DMA32 0x00001000 -> 0x00100000
[ 0.000000] Normal 0x00100000 -> 0x00100000
[ 0.000000] Movable zone start PFN for each node
[ 0.000000] early_node_map[6] active PFN ranges
[ 0.000000] 0: 0x00000000 -> 0x0000008f
[ 0.000000] 0: 0x00000090 -> 0x0000009e
[ 0.000000] 0: 0x00000100 -> 0x0007ee98
[ 0.000000] 0: 0x0007eebf -> 0x0007eeff
[ 0.000000] 0: 0x0007efbf -> 0x0007eff2
[ 0.000000] 0: 0x0007efff -> 0x0007f000
[ 0.000000] On node 0 totalpages: 519849
[ 0.000000] DMA zone: 56 pages used for memmap
[ 0.000000] DMA zone: 101 pages reserved
[ 0.000000] DMA zone: 3840 pages, LIFO batch:0
[ 0.000000] DMA32 zone: 7056 pages used for memmap
[ 0.000000] DMA32 zone: 508796 pages, LIFO batch:31
[ 0.000000] ACPI: PM-Timer IO Port: 0x408
[ 0.000000] ACPI: Local APIC address 0xfee00000
[ 0.000000] ACPI: LAPIC (acpi_id[0x01] lapic_id[0x00] enabled)
[ 0.000000] ACPI: LAPIC (acpi_id[0x02] lapic_id[0x01] enabled)
[ 0.000000] ACPI: LAPIC (acpi_id[0x03] lapic_id[0x02] enabled)
[ 0.000000] ACPI: LAPIC (acpi_id[0x04] lapic_id[0x03] enabled)
[ 0.000000] ACPI: LAPIC_NMI (acpi_id[0x01] high level lint[0x1])
[ 0.000000] ACPI: LAPIC_NMI (acpi_id[0x02] high level lint[0x1])
[ 0.000000] ACPI: LAPIC_NMI (acpi_id[0x03] high level lint[0x1])
[ 0.000000] ACPI: LAPIC_NMI (acpi_id[0x04] high level lint[0x1])
[ 0.000000] ACPI: IOAPIC (id[0x08] address[0xfec00000] gsi_base[0])
[ 0.000000] IOAPIC[0]: apic_id 8, version 32, address 0xfec00000, GSI 0-23
[ 0.000000] ACPI: INT_SRC_OVR (bus 0 bus_irq 0 global_irq 2 dfl dfl)
[ 0.000000] ACPI: INT_SRC_OVR (bus 0 bus_irq 9 global_irq 9 high level)
[ 0.000000] ACPI: IRQ0 used by override.
[ 0.000000] ACPI: IRQ2 used by override.
[ 0.000000] ACPI: IRQ9 used by override.
[ 0.000000] Using ACPI (MADT) for SMP configuration information
[ 0.000000] ACPI: HPET id: 0x8086a201 base: 0xfed00000
[ 0.000000] SMP: Allowing 4 CPUs, 0 hotplug CPUs
[ 0.000000] nr_irqs_gsi: 24
[ 0.000000] PM: Registered nosave memory: 000000000008f000 - 0000000000090000
[ 0.000000] PM: Registered nosave memory: 000000000009e000 - 000000000009f000
[ 0.000000] PM: Registered nosave memory: 000000000009f000 - 00000000000a0000
[ 0.000000] PM: Registered nosave memory: 00000000000a0000 - 00000000000e0000
[ 0.000000] PM: Registered nosave memory: 00000000000e0000 - 0000000000100000
[ 0.000000] PM: Registered nosave memory: 000000007ee98000 - 000000007eebf000
[ 0.000000] PM: Registered nosave memory: 000000007eeff000 - 000000007efbf000
[ 0.000000] PM: Registered nosave memory: 000000007eff2000 - 000000007efff000
[ 0.000000] Allocating PCI resources starting at 80000000 (gap: 80000000:60000000)
[ 0.000000] Booting paravirtualized kernel on bare hardware
[ 0.000000] NR_CPUS:512 nr_cpumask_bits:512 nr_cpu_ids:4 nr_node_ids:1
[ 0.000000] PERCPU: Embedded 30 pages/cpu @ffff880001800000 s90392 r8192 d24296 u524288
[ 0.000000] pcpu-alloc: s90392 r8192 d24296 u524288 alloc=1*2097152
[ 0.000000] pcpu-alloc: [0] 0 1 2 3
[ 0.000000] Built 1 zonelists in Node order, mobility grouping on. Total pages: 512636
[ 0.000000] Policy zone: DMA32
[ 0.000000] Kernel command line: BOOT_IMAGE=/boot/vmlinuz-2.6.32-5-amd64 root=UUID=54290ac6-2db5-424b-8cdb-e54f7e644b70 ro quiet
[ 0.000000] PID hash table entries: 4096 (order: 3, 32768 bytes)
[ 0.000000] Initializing CPU#0
[ 0.000000] Checking aperture...
[ 0.000000] No AGP bridge found
[ 0.000000] Calgary: detecting Calgary via BIOS EBDA area
[ 0.000000] Calgary: Unable to locate Rio Grande table in EBDA - bailing!
[ 0.000000] Memory: 2033784k/2080768k available (3087k kernel code, 1372k absent, 45612k reserved, 2052k data, 592k init)
[ 0.000000] SLUB: Genslabs=14, HWalign=64, Order=0-3, MinObjects=0, CPUs=4, Nodes=1
[ 0.000000] Hierarchical RCU implementation.
[ 0.000000] NR_IRQS:4352 nr_irqs:440
[ 0.000000] Extended CMOS year: 2000
[ 0.000000] Console: colour VGA+ 80x25
[ 0.000000] console [tty0] enabled
[ 0.000000] hpet clockevent registered
[ 0.000000] Fast TSC calibration using PIT
[ 0.004000] Detected 2133.336 MHz processor.
[ 0.000008] Calibrating delay loop (skipped), value calculated using timer frequency.. 4266.67 BogoMIPS (lpj=8533344)
[ 0.000049] Security Framework initialized
[ 0.000056] SELinux: Disabled at boot.
[ 0.000398] Dentry cache hash table entries: 262144 (order: 9, 2097152 bytes)
[ 0.001959] Inode-cache hash table entries: 131072 (order: 8, 1048576 bytes)
[ 0.002686] Mount-cache hash table entries: 256
[ 0.002953] Initializing cgroup subsys ns
[ 0.002960] Initializing cgroup subsys cpuacct
[ 0.002967] Initializing cgroup subsys devices
[ 0.002971] Initializing cgroup subsys freezer
[ 0.002975] Initializing cgroup subsys net_cls
[ 0.003017] CPU: L1 I cache: 32K, L1 D cache: 24K
[ 0.003021] CPU: L2 cache: 512K
[ 0.003027] CPU 0/0x0 -> Node 0
[ 0.003030] CPU: Physical Processor ID: 0
[ 0.003033] CPU: Processor Core ID: 0
[ 0.003038] mce: CPU supports 5 MCE banks
[ 0.003048] CPU0: Thermal monitoring enabled (TM1)
[ 0.003055] using mwait in idle threads.
[ 0.003058] Performance Events: Nehalem/Corei7 events, Intel PMU driver.
[ 0.003067] ... version: 3
[ 0.003070] ... bit width: 40
[ 0.003073] ... generic registers: 2
[ 0.003076] ... value mask: 000000ffffffffff
[ 0.003079] ... max period: 000000007fffffff
[ 0.003082] ... fixed-purpose events: 3
[ 0.003085] ... event mask: 0000000700000003
[ 0.004215] ACPI: Core revision 20090903
[ 0.015804] Setting APIC routing to flat
[ 0.016171] ..TIMER: vector=0x30 apic1=0 pin1=2 apic2=-1 pin2=-1
[ 0.056185] CPU0: Intel(R) Atom(TM) CPU D2700 @ 2.13GHz stepping 01
[ 0.163445] Booting processor 1 APIC 0x1 ip 0x6000
[ 0.173430] Initializing CPU#1
[ 0.250995] CPU: L1 I cache: 32K, L1 D cache: 24K
[ 0.250999] CPU: L2 cache: 512K
[ 0.251004] CPU 1/0x1 -> Node 0
[ 0.251008] CPU: Physical Processor ID: 0
[ 0.251011] CPU: Processor Core ID: 0
[ 0.251023] CPU1: Thermal monitoring enabled (TM1)
[ 0.251039] CPU1: Intel(R) Atom(TM) CPU D2700 @ 2.13GHz stepping 01
[ 0.251051] checking TSC synchronization [CPU#0 -> CPU#1]: passed.
[ 0.271190] Booting processor 2 APIC 0x2 ip 0x6000
[ 0.281119] Initializing CPU#2
[ 0.358771] CPU: L1 I cache: 32K, L1 D cache: 24K
[ 0.358775] CPU: L2 cache: 512K
[ 0.358780] CPU 2/0x2 -> Node 0
[ 0.358783] CPU: Physical Processor ID: 0
[ 0.358785] CPU: Processor Core ID: 1
[ 0.358795] CPU2: Thermal monitoring enabled (TM1)
[ 0.358862] CPU2: Intel(R) Atom(TM) CPU D2700 @ 2.13GHz stepping 01
[ 0.358873] checking TSC synchronization [CPU#0 -> CPU#2]: passed.
[ 0.378970] Booting processor 3 APIC 0x3 ip 0x6000
[ 0.388901] Initializing CPU#3
[ 0.466548] CPU: L1 I cache: 32K, L1 D cache: 24K
[ 0.466552] CPU: L2 cache: 512K
[ 0.466556] CPU 3/0x3 -> Node 0
[ 0.466559] CPU: Physical Processor ID: 0
[ 0.466561] CPU: Processor Core ID: 1
[ 0.466571] CPU3: Thermal monitoring enabled (TM1)
[ 0.466644] CPU3: Intel(R) Atom(TM) CPU D2700 @ 2.13GHz stepping 01
[ 0.466654] checking TSC synchronization [CPU#0 -> CPU#3]: passed.
[ 0.486641] Brought up 4 CPUs
[ 0.486646] Total of 4 processors activated (17067.07 BogoMIPS).
[ 0.487095] CPU0 attaching sched-domain:
[ 0.487101] domain 0: span 0-1 level SIBLING
[ 0.487106] groups: group ffff88000180fae0 cpus 0 (cpu_power = 589) group ffff88000188fae0 cpus 1 (cpu_power = 589)
[ 0.487118] domain 1: span 0-1 level MC
[ 0.487122] groups: group ffff88000180fbf0 cpus 0-1 (cpu_power = 1178)
[ 0.487130] domain 2: span 0-3 level CPU
[ 0.487134] groups: group ffff88000180fd00 cpus 0-1 (cpu_power = 1178) group ffff88000190fd00 cpus 2-3 (cpu_power = 1178)
[ 0.487149] CPU1 attaching sched-domain:
[ 0.487153] domain 0: span 0-1 level SIBLING
[ 0.487156] groups: group ffff88000188fae0 cpus 1 (cpu_power = 589) group ffff88000180fae0 cpus 0 (cpu_power = 589)
[ 0.487167] domain 1: span 0-1 level MC
[ 0.487171] groups: group ffff88000180fbf0 cpus 0-1 (cpu_power = 1178)
[ 0.487179] domain 2: span 0-3 level CPU
[ 0.487183] groups: group ffff88000180fd00 cpus 0-1 (cpu_power = 1178) group ffff88000190fd00 cpus 2-3 (cpu_power = 1178)
[ 0.487196] CPU2 attaching sched-domain:
[ 0.487199] domain 0: span 2-3 level SIBLING
[ 0.487203] groups: group ffff88000190fae0 cpus 2 (cpu_power = 589) group ffff88000198fae0 cpus 3 (cpu_power = 589)
[ 0.487214] domain 1: span 2-3 level MC
[ 0.487218] groups: group ffff88000190fbf0 cpus 2-3 (cpu_power = 1178)
[ 0.487225] domain 2: span 0-3 level CPU
[ 0.487229] groups: group ffff88000190fd00 cpus 2-3 (cpu_power = 1178) group ffff88000180fd00 cpus 0-1 (cpu_power = 1178)
[ 0.487242] CPU3 attaching sched-domain:
[ 0.487246] domain 0: span 2-3 level SIBLING
[ 0.487249] groups: group ffff88000198fae0 cpus 3 (cpu_power = 589) group ffff88000190fae0 cpus 2 (cpu_power = 589)
[ 0.487260] domain 1: span 2-3 level MC
[ 0.487264] groups: group ffff88000190fbf0 cpus 2-3 (cpu_power = 1178)
[ 0.487272] domain 2: span 0-3 level CPU
[ 0.487275] groups: group ffff88000190fd00 cpus 2-3 (cpu_power = 1178) group ffff88000180fd00 cpus 0-1 (cpu_power = 1178)
[ 0.487853] devtmpfs: initialized
[ 0.491880] regulator: core version 0.5
[ 0.491978] NET: Registered protocol family 16
[ 0.492165] ACPI FADT declares the system doesn't support PCIe ASPM, so disable it
[ 0.492170] ACPI: bus type pci registered
[ 0.492296] PCI: MCFG configuration 0: base e0000000 segment 0 buses 0 - 63
[ 0.492300] PCI: MCFG area at e0000000 reserved in E820
[ 0.496226] PCI: Using MMCONFIG at e0000000 - e3ffffff
[ 0.496230] PCI: Using configuration type 1 for base access
[ 0.497220] bio: create slab <bio-0> at 0
[ 0.498434] ACPI: EC: Look up EC in DSDT
[ 0.500992] ACPI: Executed 1 blocks of module-level executable AML code
[ 0.504268] ACPI: BIOS _OSI(Linux) query ignored
[ 0.506917] ACPI: Interpreter enabled
[ 0.506923] ACPI: (supports S0 S3 S4 S5)
[ 0.506962] ACPI: Using IOAPIC for interrupt routing
[ 0.517173] ACPI: No dock devices found.
[ 0.521312] _OSC invalid UUID
[ 0.521317] ACPI: PCI Root Bridge [PCI0] (0000:00)
[ 0.521464] pci 0000:00:02.0: reg 10 32bit mmio: [0x80200000-0x802fffff]
[ 0.521472] pci 0000:00:02.0: reg 14 io port: [0x30d0-0x30d7]
[ 0.521577] pci 0000:00:1b.0: reg 10 64bit mmio: [0x80400000-0x80403fff]
[ 0.521643] pci 0000:00:1b.0: PME# supported from D0 D3hot D3cold
[ 0.521650] pci 0000:00:1b.0: PME# disabled
[ 0.521746] pci 0000:00:1c.0: PME# supported from D0 D3hot D3cold
[ 0.521752] pci 0000:00:1c.0: PME# disabled
[ 0.521827] pci 0000:00:1d.0: reg 20 io port: [0x30a0-0x30bf]
[ 0.521906] pci 0000:00:1d.1: reg 20 io port: [0x3080-0x309f]
[ 0.521987] pci 0000:00:1d.2: reg 20 io port: [0x3060-0x307f]
[ 0.522070] pci 0000:00:1d.3: reg 20 io port: [0x3040-0x305f]
[ 0.522144] pci 0000:00:1d.7: reg 10 32bit mmio: [0x80304400-0x803047ff]
[ 0.522218] pci 0000:00:1d.7: PME# supported from D0 D3hot D3cold
[ 0.522226] pci 0000:00:1d.7: PME# disabled
[ 0.522383] pci 0000:00:1f.0: [Firmware Bug]: TigerPoint LPC.BM_STS cleared
[ 0.522470] pci 0000:00:1f.2: reg 10 io port: [0x30c8-0x30cf]
[ 0.522479] pci 0000:00:1f.2: reg 14 io port: [0x30dc-0x30df]
[ 0.522487] pci 0000:00:1f.2: reg 18 io port: [0x30c0-0x30c7]
[ 0.522496] pci 0000:00:1f.2: reg 1c io port: [0x30d8-0x30db]
[ 0.522505] pci 0000:00:1f.2: reg 20 io port: [0x3020-0x302f]
[ 0.522514] pci 0000:00:1f.2: reg 24 32bit mmio: [0x80304000-0x803043ff]
[ 0.522558] pci 0000:00:1f.2: PME# supported from D3hot
[ 0.522563] pci 0000:00:1f.2: PME# disabled
[ 0.522622] pci 0000:00:1f.3: reg 20 io port: [0x3000-0x301f]
[ 0.522801] pci 0000:01:00.0: reg 10 32bit mmio: [0x80120000-0x8013ffff]
[ 0.522818] pci 0000:01:00.0: reg 14 32bit mmio: [0x80100000-0x8011ffff]
[ 0.522834] pci 0000:01:00.0: reg 18 io port: [0x2000-0x201f]
[ 0.522851] pci 0000:01:00.0: reg 1c 32bit mmio: [0x80140000-0x80143fff]
[ 0.523004] pci 0000:01:00.0: PME# supported from D0 D3hot D3cold
[ 0.523014] pci 0000:01:00.0: PME# disabled
[ 0.523114] pci 0000:00:1c.0: bridge io port: [0x2000-0x2fff]
[ 0.523120] pci 0000:00:1c.0: bridge 32bit mmio: [0x80100000-0x801fffff]
[ 0.523277] pci 0000:00:1e.0: transparent bridge
[ 0.523283] pci 0000:00:1e.0: bridge io port: [0x1000-0x1fff]
[ 0.523289] pci 0000:00:1e.0: bridge 32bit mmio: [0x80000000-0x800fffff]
[ 0.523350] pci 0000:03:00.0: reg 10 io port: [0x1300-0x13ff]
[ 0.523362] pci 0000:03:00.0: reg 14 32bit mmio: [0x80000300-0x800003ff]
[ 0.523445] pci 0000:03:00.0: supports D1 D2
[ 0.523449] pci 0000:03:00.0: PME# supported from D0 D1 D2 D3hot D3cold
[ 0.523456] pci 0000:03:00.0: PME# disabled
[ 0.523521] pci 0000:03:01.0: reg 10 io port: [0x1200-0x12ff]
[ 0.523533] pci 0000:03:01.0: reg 14 32bit mmio: [0x80000200-0x800002ff]
[ 0.523615] pci 0000:03:01.0: supports D1 D2
[ 0.523619] pci 0000:03:01.0: PME# supported from D0 D1 D2 D3hot D3cold
[ 0.523627] pci 0000:03:01.0: PME# disabled
[ 0.523696] pci 0000:03:02.0: reg 10 io port: [0x1100-0x11ff]
[ 0.523708] pci 0000:03:02.0: reg 14 32bit mmio: [0x80000100-0x800001ff]
[ 0.523793] pci 0000:03:02.0: supports D1 D2
[ 0.523797] pci 0000:03:02.0: PME# supported from D0 D1 D2 D3hot D3cold
[ 0.523804] pci 0000:03:02.0: PME# disabled
[ 0.523871] pci 0000:03:03.0: reg 10 io port: [0x1000-0x10ff]
[ 0.523883] pci 0000:03:03.0: reg 14 32bit mmio: [0x80000000-0x800000ff]
[ 0.523969] pci 0000:03:03.0: supports D1 D2
[ 0.523972] pci 0000:03:03.0: PME# supported from D0 D1 D2 D3hot D3cold
[ 0.523980] pci 0000:03:03.0: PME# disabled
[ 0.524061] pci 0000:02:00.0: bridge io port: [0x1000-0x1fff]
[ 0.524068] pci 0000:02:00.0: bridge 32bit mmio: [0x80000000-0x800fffff]
[ 0.524100] ACPI: PCI Interrupt Routing Table [\_SB_.PCI0._PRT]
[ 0.524264] ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.P0P1._PRT]
[ 0.524533] ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.RP01._PRT]
[ 0.524785] _OSC invalid UUID
[ 0.533137] ACPI: PCI Interrupt Link [LNKA] (IRQs 1 3 4 5 6 7 10 12 14 15) *11
[ 0.533303] ACPI: PCI Interrupt Link [LNKB] (IRQs 1 3 4 5 6 7 11 12 14 15) *0, disabled.
[ 0.533466] ACPI: PCI Interrupt Link [LNKC] (IRQs 1 3 4 5 6 7 10 12 14 15) *9
[ 0.533624] ACPI: PCI Interrupt Link [LNKD] (IRQs 1 3 4 5 6 7 *11 12 14 15)
[ 0.533779] ACPI: PCI Interrupt Link [LNKE] (IRQs 1 3 4 5 6 7 *10 12 14 15)
[ 0.533935] ACPI: PCI Interrupt Link [LNKF] (IRQs 1 3 4 5 6 7 *11 12 14 15)
[ 0.534091] ACPI: PCI Interrupt Link [LNKG] (IRQs 1 3 4 5 6 7 10 12 14 15) *9
[ 0.534248] ACPI: PCI Interrupt Link [LNKH] (IRQs 1 3 4 5 6 7 11 12 14 15) *10
[ 0.534442] vgaarb: device added: PCI:0000:00:02.0,decodes=io+mem,owns=io+mem,locks=none
[ 0.534460] vgaarb: loaded
[ 0.534614] PCI: Using ACPI for IRQ routing
[ 0.534949] hpet0: at MMIO 0xfed00000, IRQs 2, 8, 0
[ 0.534957] hpet0: 3 comparators, 64-bit 14.318180 MHz counter
[ 0.536978] Switching to clocksource tsc
[ 0.539053] pnp: PnP ACPI init
[ 0.539090] ACPI: bus type pnp registered
[ 0.541729] pnp: PnP ACPI: found 9 devices
[ 0.541734] ACPI: ACPI bus type pnp unregistered
[ 0.541756] system 00:03: iomem range 0xfed00000-0xfed003ff has been reserved
[ 0.541769] system 00:05: ioport range 0x680-0x69f has been reserved
[ 0.541774] system 00:05: ioport range 0xffff-0xffff has been reserved
[ 0.541780] system 00:05: ioport range 0xffff-0xffff has been reserved
[ 0.541785] system 00:05: ioport range 0xffff-0xffff has been reserved
[ 0.541791] system 00:05: ioport range 0x400-0x47f has been reserved
[ 0.541796] system 00:05: ioport range 0x500-0x57f has been reserved
[ 0.541801] system 00:05: ioport range 0x600-0x61f has been reserved
[ 0.541810] system 00:06: ioport range 0x6a0-0x6af has been reserved
[ 0.541816] system 00:06: ioport range 0x6b0-0x6ff has been reserved
[ 0.541826] system 00:08: iomem range 0xfed1c000-0xfed1ffff has been reserved
[ 0.541832] system 00:08: iomem range 0x0-0x3fff could not be reserved
[ 0.541837] system 00:08: iomem range 0x0-0xfff could not be reserved
[ 0.541842] system 00:08: iomem range 0x0-0xfff could not be reserved
[ 0.541848] system 00:08: iomem range 0xfed45000-0xfed8ffff has been reserved
[ 0.546881] pci 0000:00:1c.0: PCI bridge, secondary bus 0000:01
[ 0.546887] pci 0000:00:1c.0: IO window: 0x2000-0x2fff
[ 0.546895] pci 0000:00:1c.0: MEM window: 0x80100000-0x801fffff
[ 0.546902] pci 0000:00:1c.0: PREFETCH window: 0x00000080500000-0x000000806fffff
[ 0.546913] pci 0000:02:00.0: PCI bridge, secondary bus 0000:03
[ 0.546918] pci 0000:02:00.0: IO window: 0x1000-0x1fff
[ 0.546926] pci 0000:02:00.0: MEM window: 0x80000000-0x800fffff
[ 0.546932] pci 0000:02:00.0: PREFETCH window: disabled
[ 0.546943] pci 0000:00:1e.0: PCI bridge, secondary bus 0000:02
[ 0.546948] pci 0000:00:1e.0: IO window: 0x1000-0x1fff
[ 0.546954] pci 0000:00:1e.0: MEM window: 0x80000000-0x800fffff
[ 0.546960] pci 0000:00:1e.0: PREFETCH window: disabled
[ 0.546984] alloc irq_desc for 16 on node -1
[ 0.546993] alloc kstat_irqs on node -1
[ 0.547008] pci 0000:00:1c.0: PCI INT A -> GSI 16 (level, low) -> IRQ 16
[ 0.547015] pci 0000:00:1c.0: setting latency timer to 64
[ 0.547025] pci 0000:00:1e.0: setting latency timer to 64
[ 0.547043] pci_bus 0000:00: resource 0 io: [0x00-0xffff]
[ 0.547048] pci_bus 0000:00: resource 1 mem: [0x000000-0xffffffffffffffff]
[ 0.547053] pci_bus 0000:01: resource 0 io: [0x2000-0x2fff]
[ 0.547058] pci_bus 0000:01: resource 1 mem: [0x80100000-0x801fffff]
[ 0.547062] pci_bus 0000:01: resource 2 pref mem [0x80500000-0x806fffff]
[ 0.547067] pci_bus 0000:02: resource 0 io: [0x1000-0x1fff]
[ 0.547072] pci_bus 0000:02: resource 1 mem: [0x80000000-0x800fffff]
[ 0.547076] pci_bus 0000:02: resource 3 io: [0x00-0xffff]
[ 0.547081] pci_bus 0000:02: resource 4 mem: [0x000000-0xffffffffffffffff]
[ 0.547086] pci_bus 0000:03: resource 0 io: [0x1000-0x1fff]
[ 0.547090] pci_bus 0000:03: resource 1 mem: [0x80000000-0x800fffff]
[ 0.547149] NET: Registered protocol family 2
[ 0.547390] IP route cache hash table entries: 65536 (order: 7, 524288 bytes)
[ 0.548885] TCP established hash table entries: 262144 (order: 10, 4194304 bytes)
[ 0.551860] TCP bind hash table entries: 65536 (order: 8, 1048576 bytes)
[ 0.552555] TCP: Hash tables configured (established 262144 bind 65536)
[ 0.552560] TCP reno registered
[ 0.552763] NET: Registered protocol family 1
[ 0.552811] pci 0000:00:02.0: Boot video device
[ 0.552834] alloc irq_desc for 23 on node -1
[ 0.552839] alloc kstat_irqs on node -1
[ 0.552853] pci 0000:00:1d.0: PCI INT A -> GSI 23 (level, low) -> IRQ 23
[ 0.552874] pci 0000:00:1d.0: PCI INT A disabled
[ 0.552885] alloc irq_desc for 19 on node -1
[ 0.552888] alloc kstat_irqs on node -1
[ 0.552895] pci 0000:00:1d.1: PCI INT B -> GSI 19 (level, low) -> IRQ 19
[ 0.552916] pci 0000:00:1d.1: PCI INT B disabled
[ 0.552931] alloc irq_desc for 18 on node -1
[ 0.552935] alloc kstat_irqs on node -1
[ 0.552942] pci 0000:00:1d.2: PCI INT C -> GSI 18 (level, low) -> IRQ 18
[ 0.552964] pci 0000:00:1d.2: PCI INT C disabled
[ 0.552976] pci 0000:00:1d.3: PCI INT D -> GSI 16 (level, low) -> IRQ 16
[ 0.552997] pci 0000:00:1d.3: PCI INT D disabled
[ 0.553012] pci 0000:00:1d.7: PCI INT A -> GSI 23 (level, low) -> IRQ 23
[ 0.570480] pci 0000:00:1d.7: PCI INT A disabled
[ 0.570602] Unpacking initramfs...
[ 0.918667] Freeing initrd memory: 9105k freed
[ 0.926323] audit: initializing netlink socket (disabled)
[ 0.926342] type=2000 audit(1369197303.773:1): initialized
[ 0.931035] HugeTLB registered 2 MB page size, pre-allocated 0 pages
[ 0.933724] VFS: Disk quotas dquot_6.5.2
[ 0.933829] Dquot-cache hash table entries: 512 (order 0, 4096 bytes)
[ 0.933975] msgmni has been set to 3990
[ 0.934386] alg: No test for stdrng (krng)
[ 0.934494] Block layer SCSI generic (bsg) driver version 0.4 loaded (major 253)
[ 0.934499] io scheduler noop registered
[ 0.934502] io scheduler anticipatory registered
[ 0.934505] io scheduler deadline registered
[ 0.934615] io scheduler cfq registered (default)
[ 0.934794] alloc irq_desc for 24 on node -1
[ 0.934798] alloc kstat_irqs on node -1
[ 0.934814] pcieport 0000:00:1c.0: irq 24 for MSI/MSI-X
[ 0.934826] pcieport 0000:00:1c.0: setting latency timer to 64
[ 0.937873] Linux agpgart interface v0.103
[ 0.937950] Serial: 8250/16550 driver, 4 ports, IRQ sharing enabled
[ 0.938523] input: Macintosh mouse button emulation as /devices/virtual/input/input0
[ 0.938633] PNP: No PS/2 controller found. Probing ports directly.
[ 0.941313] serio: i8042 KBD port at 0x60,0x64 irq 1
[ 0.941324] serio: i8042 AUX port at 0x60,0x64 irq 12
[ 0.941497] mice: PS/2 mouse device common for all mice
[ 0.941560] rtc_cmos 00:07: RTC can wake from S4
[ 0.941634] rtc_cmos 00:07: rtc core: registered rtc_cmos as rtc0
[ 0.941669] rtc0: alarms up to one month, y3k, 242 bytes nvram, hpet irqs
[ 0.941688] cpuidle: using governor ladder
[ 0.941693] cpuidle: using governor menu
[ 0.941712] No iBFT detected.
[ 0.942338] TCP cubic registered
[ 0.942592] NET: Registered protocol family 10
[ 0.943885] Mobile IPv6
[ 0.943891] NET: Registered protocol family 17
[ 0.944065] PM: Resume from disk failed.
[ 0.944083] registered taskstats version 1
[ 0.944635] rtc_cmos 00:07: setting system clock to 2013-05-22 04:35:04 UTC (1369197304)
[ 0.944740] Initalizing network drop monitor service
[ 0.944793] Freeing unused kernel memory: 592k freed
[ 0.945019] Write protecting the kernel read-only data: 4252k
[ 0.972849] udev[76]: starting version 164
[ 1.063074] e1000e: Intel(R) PRO/1000 Network Driver - 1.2.20-k2
[ 1.063082] e1000e: Copyright(c) 1999 - 2011 Intel Corporation.
[ 1.063238] e1000e 0000:01:00.0: PCI INT A -> GSI 16 (level, low) -> IRQ 16
[ 1.063293] e1000e 0000:01:00.0: setting latency timer to 64
[ 1.063562] alloc irq_desc for 25 on node -1
[ 1.063569] alloc kstat_irqs on node -1
[ 1.063587] e1000e 0000:01:00.0: irq 25 for MSI/MSI-X
[ 1.063594] alloc irq_desc for 26 on node -1
[ 1.063598] alloc kstat_irqs on node -1
[ 1.063607] e1000e 0000:01:00.0: irq 26 for MSI/MSI-X
[ 1.063614] alloc irq_desc for 27 on node -1
[ 1.063618] alloc kstat_irqs on node -1
[ 1.063626] e1000e 0000:01:00.0: irq 27 for MSI/MSI-X
[ 1.063828] e1000e 0000:01:00.0: Disabling ASPM L0s
[ 1.092765] usbcore: registered new interface driver usbfs
[ 1.092831] usbcore: registered new interface driver hub
[ 1.092951] usbcore: registered new device driver usb
[ 1.098087] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
[ 1.098148] ehci_hcd 0000:00:1d.7: PCI INT A -> GSI 23 (level, low) -> IRQ 23
[ 1.098194] ehci_hcd 0000:00:1d.7: setting latency timer to 64
[ 1.098202] ehci_hcd 0000:00:1d.7: EHCI Host Controller
[ 1.098255] ehci_hcd 0000:00:1d.7: new USB bus registered, assigned bus number 1
[ 1.098333] ehci_hcd 0000:00:1d.7: using broken periodic workaround
[ 1.098353] ehci_hcd 0000:00:1d.7: debug port 1
[ 1.102256] ehci_hcd 0000:00:1d.7: cache line size of 32 is not supported
[ 1.104910] ehci_hcd 0000:00:1d.7: irq 23, io mem 0x80304400
[ 1.117298] ehci_hcd 0000:00:1d.7: USB 2.0 started, EHCI 1.00
[ 1.117363] usb usb1: New USB device found, idVendor=1d6b, idProduct=0002
[ 1.117368] usb usb1: New USB device strings: Mfr=3, Product=2, SerialNumber=1
[ 1.117372] usb usb1: Product: EHCI Host Controller
[ 1.117376] usb usb1: Manufacturer: Linux 2.6.32-5-amd64 ehci_hcd
[ 1.117380] usb usb1: SerialNumber: 0000:00:1d.7
[ 1.117534] usb usb1: configuration #1 chosen from 1 choice
[ 1.117616] hub 1-0:1.0: USB hub found
[ 1.117635] hub 1-0:1.0: 8 ports detected
[ 1.125784] SCSI subsystem initialized
[ 1.134211] via-rhine.c:v1.10-LK1.4.3 2007-03-06 Written by Donald Becker
[ 1.134296] alloc irq_desc for 20 on node -1
[ 1.134302] alloc kstat_irqs on node -1
[ 1.134320] via-rhine 0000:03:00.0: PCI INT A -> GSI 20 (level, low) -> IRQ 20
[ 1.134635] via-rhine: Woke system up. Reason: Unknown.
[ 1.134644] via-rhine: Reset not complete yet. Trying harder.
[ 1.137009] Invalid MAC address
[ 1.137061] via-rhine: probe of 0000:03:00.0 failed with error -5
[ 1.137097] alloc irq_desc for 21 on node -1
[ 1.137100] alloc kstat_irqs on node -1
[ 1.137113] via-rhine 0000:03:01.0: PCI INT A -> GSI 21 (level, low) -> IRQ 21
[ 1.137140] via-rhine: Woke system up. Reason: Unknown.
[ 1.137146] via-rhine: Reset not complete yet. Trying harder.
[ 1.138430] uhci_hcd: USB Universal Host Controller Interface driver
[ 1.138536] uhci_hcd 0000:00:1d.0: PCI INT A -> GSI 23 (level, low) -> IRQ 23
[ 1.139599] Invalid MAC address
[ 1.139674] via-rhine: probe of 0000:03:01.0 failed with error -5
[ 1.139725] alloc irq_desc for 22 on node -1
[ 1.139729] alloc kstat_irqs on node -1
[ 1.139744] via-rhine 0000:03:02.0: PCI INT A -> GSI 22 (level, low) -> IRQ 22
[ 1.139775] via-rhine: Woke system up. Reason: Unknown.
[ 1.139782] via-rhine: Reset not complete yet. Trying harder.
[ 1.139860] uhci_hcd 0000:00:1d.0: setting latency timer to 64
[ 1.139871] uhci_hcd 0000:00:1d.0: UHCI Host Controller
[ 1.139912] uhci_hcd 0000:00:1d.0: new USB bus registered, assigned bus number 2
[ 1.139974] uhci_hcd 0000:00:1d.0: irq 23, io base 0x000030a0
[ 1.140091] usb usb2: New USB device found, idVendor=1d6b, idProduct=0001
[ 1.140098] usb usb2: New USB device strings: Mfr=3, Product=2, SerialNumber=1
[ 1.140103] usb usb2: Product: UHCI Host Controller
[ 1.140108] usb usb2: Manufacturer: Linux 2.6.32-5-amd64 uhci_hcd
[ 1.140113] usb usb2: SerialNumber: 0000:00:1d.0
[ 1.140324] usb usb2: configuration #1 chosen from 1 choice
[ 1.140405] hub 2-0:1.0: USB hub found
[ 1.140422] hub 2-0:1.0: 2 ports detected
[ 1.140549] uhci_hcd 0000:00:1d.1: PCI INT B -> GSI 19 (level, low) -> IRQ 19
[ 1.140572] uhci_hcd 0000:00:1d.1: setting latency timer to 64
[ 1.140580] uhci_hcd 0000:00:1d.1: UHCI Host Controller
[ 1.140600] uhci_hcd 0000:00:1d.1: new USB bus registered, assigned bus number 3
[ 1.140682] uhci_hcd 0000:00:1d.1: irq 19, io base 0x00003080
[ 1.140780] usb usb3: New USB device found, idVendor=1d6b, idProduct=0001
[ 1.140786] usb usb3: New USB device strings: Mfr=3, Product=2, SerialNumber=1
[ 1.140792] usb usb3: Product: UHCI Host Controller
[ 1.140797] usb usb3: Manufacturer: Linux 2.6.32-5-amd64 uhci_hcd
[ 1.140802] usb usb3: SerialNumber: 0000:00:1d.1
[ 1.140979] usb usb3: configuration #1 chosen from 1 choice
[ 1.141056] hub 3-0:1.0: USB hub found
[ 1.141072] hub 3-0:1.0: 2 ports detected
[ 1.141197] uhci_hcd 0000:00:1d.2: PCI INT C -> GSI 18 (level, low) -> IRQ 18
[ 1.141219] uhci_hcd 0000:00:1d.2: setting latency timer to 64
[ 1.141227] uhci_hcd 0000:00:1d.2: UHCI Host Controller
[ 1.141249] uhci_hcd 0000:00:1d.2: new USB bus registered, assigned bus number 4
[ 1.141348] uhci_hcd 0000:00:1d.2: irq 18, io base 0x00003060
[ 1.141448] usb usb4: New USB device found, idVendor=1d6b, idProduct=0001
[ 1.141455] usb usb4: New USB device strings: Mfr=3, Product=2, SerialNumber=1
[ 1.141460] usb usb4: Product: UHCI Host Controller
[ 1.141465] usb usb4: Manufacturer: Linux 2.6.32-5-amd64 uhci_hcd
[ 1.141471] usb usb4: SerialNumber: 0000:00:1d.2
[ 1.141649] usb usb4: configuration #1 chosen from 1 choice
[ 1.141724] hub 4-0:1.0: USB hub found
[ 1.141741] hub 4-0:1.0: 2 ports detected
[ 1.141865] uhci_hcd 0000:00:1d.3: PCI INT D -> GSI 16 (level, low) -> IRQ 16
[ 1.141888] uhci_hcd 0000:00:1d.3: setting latency timer to 64
[ 1.141896] uhci_hcd 0000:00:1d.3: UHCI Host Controller
[ 1.141917] uhci_hcd 0000:00:1d.3: new USB bus registered, assigned bus number 5
[ 1.141999] uhci_hcd 0000:00:1d.3: irq 16, io base 0x00003040
[ 1.142098] usb usb5: New USB device found, idVendor=1d6b, idProduct=0001
[ 1.142105] usb usb5: New USB device strings: Mfr=3, Product=2, SerialNumber=1
[ 1.142110] usb usb5: Product: UHCI Host Controller
[ 1.142115] usb usb5: Manufacturer: Linux 2.6.32-5-amd64 uhci_hcd
[ 1.142121] usb usb5: SerialNumber: 0000:00:1d.3
[ 1.142289] usb usb5: configuration #1 chosen from 1 choice
[ 1.142335] Invalid MAC address
[ 1.142370] hub 5-0:1.0: USB hub found
[ 1.142376] via-rhine: probe of 0000:03:02.0 failed with error -5
[ 1.142387] hub 5-0:1.0: 2 ports detected
[ 1.142402] via-rhine 0000:03:03.0: PCI INT A -> GSI 23 (level, low) -> IRQ 23
[ 1.148705] eth0: VIA Rhine III (Management Adapter) at 0x11000, 00:00:24:cf:a5:d7, IRQ 23.
[ 1.149482] eth0: MII PHY found at address 1, status 0x7849 advertising 05e1 Link 0000.
[ 1.173888] libata version 3.00 loaded.
[ 1.180933] ahci 0000:00:1f.2: version 3.0
[ 1.180961] ahci 0000:00:1f.2: PCI INT B -> GSI 19 (level, low) -> IRQ 19
[ 1.181030] alloc irq_desc for 28 on node -1
[ 1.181036] alloc kstat_irqs on node -1
[ 1.181057] ahci 0000:00:1f.2: irq 28 for MSI/MSI-X
[ 1.181114] ahci: SSS flag set, parallel bus scan disabled
[ 1.181158] ahci 0000:00:1f.2: AHCI 0001.0100 32 slots 4 ports 3 Gbps 0x3 impl SATA mode
[ 1.181167] ahci 0000:00:1f.2: flags: 64bit ncq stag pm led clo pio slum part
[ 1.181176] ahci 0000:00:1f.2: setting latency timer to 64
[ 1.181466] scsi0 : ahci
[ 1.181715] scsi1 : ahci
[ 1.181900] scsi2 : ahci
[ 1.182066] scsi3 : ahci
[ 1.182194] ata1: SATA max UDMA/133 abar m1024@0x80304000 port 0x80304100 irq 28
[ 1.182203] ata2: SATA max UDMA/133 abar m1024@0x80304000 port 0x80304180 irq 28
[ 1.182209] ata3: DUMMY
[ 1.182212] ata4: DUMMY
[ 1.194226] e1000e 0000:01:00.0: eth1: (PCI Express:2.5GB/s:Width x1) 00:22:4d:81:9e:39
[ 1.194236] e1000e 0000:01:00.0: eth1: Intel(R) PRO/1000 Network Connection
[ 1.194260] e1000e 0000:01:00.0: eth1: MAC: 3, PHY: 8, PBA No: FFFFFF-0FF
[ 1.503166] ata1: SATA link up 1.5 Gbps (SStatus 113 SControl 300)
[ 1.541361] ata1.00: HPA detected: current 625140335, native 625142448
[ 1.541370] ata1.00: ATA-7: ST3320620AS, 3.AAK, max UDMA/133
[ 1.541375] ata1.00: 625140335 sectors, multi 16: LBA48 NCQ (depth 31/32)
[ 1.599572] ata1.00: configured for UDMA/133
[ 1.615098] scsi 0:0:0:0: Direct-Access ATA ST3320620AS 3.AA PQ: 0 ANSI: 5
[ 1.672306] usb 3-1: new low speed USB device using uhci_hcd and address 2
[ 1.842329] usb 3-1: New USB device found, idVendor=046d, idProduct=c019
[ 1.842335] usb 3-1: New USB device strings: Mfr=1, Product=2, SerialNumber=0
[ 1.842340] usb 3-1: Product: USB Optical Mouse
[ 1.842343] usb 3-1: Manufacturer: Logitech
[ 1.842491] usb 3-1: configuration #1 chosen from 1 choice
[ 1.939254] ata2: SATA link down (SStatus 0 SControl 300)
[ 1.961426] usbcore: registered new interface driver hiddev
[ 1.968499] sd 0:0:0:0: [sda] 625140335 512-byte logical blocks: (320 GB/298 GiB)
[ 1.968640] sd 0:0:0:0: [sda] Write Protect is off
[ 1.968646] sd 0:0:0:0: [sda] Mode Sense: 00 3a 00 00
[ 1.968703] sd 0:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
[ 1.969044] sda:
[ 1.974446] input: Logitech USB Optical Mouse as /devices/pci0000:00/0000:00:1d.1/usb3/3-1/3-1:1.0/input/input1
[ 1.974646] generic-usb 0003:046D:C019.0001: input,hidraw0: USB HID v1.11 Mouse [Logitech USB Optical Mouse] on usb-0000:00:1d.1-1/input0
[ 1.974708] usbcore: registered new interface driver usbhid
[ 1.974716] usbhid: v2.6:USB HID core driver
[ 1.988297] sda1 sda2 < sda5 >
[ 2.012199] sd 0:0:0:0: [sda] Attached SCSI disk
[ 2.081953] usb 4-2: new low speed USB device using uhci_hcd and address 2
[ 2.261139] usb 4-2: New USB device found, idVendor=046d, idProduct=c315
[ 2.261145] usb 4-2: New USB device strings: Mfr=1, Product=2, SerialNumber=0
[ 2.261150] usb 4-2: Product: Logitech USB Keyboard
[ 2.261154] usb 4-2: Manufacturer: Logitech
[ 2.261299] usb 4-2: configuration #1 chosen from 1 choice
[ 2.278537] input: Logitech Logitech USB Keyboard as /devices/pci0000:00/0000:00:1d.2/usb4/4-2/4-2:1.0/input/input2
[ 2.278693] generic-usb 0003:046D:C315.0002: input,hidraw1: USB HID v1.10 Keyboard [Logitech Logitech USB Keyboard] on usb-0000:00:1d.2-2/input0
[ 2.365922] PM: Starting manual resume from disk
[ 2.365928] PM: Resume from partition 8:5
[ 2.365931] PM: Checking hibernation image.
[ 2.366204] PM: Error -22 checking image file
[ 2.366207] PM: Resume from disk failed.
[ 2.419755] kjournald starting. Commit interval 5 seconds
[ 2.419767] EXT3-fs: mounted filesystem with ordered data mode.
[ 3.605864] udev[365]: starting version 164
[ 3.999933] processor LNXCPU:00: registered as cooling_device0
[ 4.000073] processor LNXCPU:01: registered as cooling_device1
[ 4.000221] processor LNXCPU:02: registered as cooling_device2
[ 4.000952] processor LNXCPU:03: registered as cooling_device3
[ 4.004810] input: PC Speaker as /devices/platform/pcspkr/input/input3
[ 4.007321] input: Power Button as /devices/LNXSYSTM:00/LNXSYBUS:00/PNP0C0C:00/input/input4
[ 4.007343] ACPI: Power Button [PWRB]
[ 4.007514] input: Sleep Button as /devices/LNXSYSTM:00/LNXSYBUS:00/PNP0C0E:00/input/input5
[ 4.007525] ACPI: Sleep Button [SLPB]
[ 4.007689] input: Power Button as /devices/LNXSYSTM:00/LNXPWRBN:00/input/input6
[ 4.007700] ACPI: Power Button [PWRF]
[ 4.286852] i801_smbus 0000:00:1f.3: PCI INT B -> GSI 19 (level, low) -> IRQ 19
[ 4.305768] pci_hotplug: PCI Hot Plug PCI Core version: 0.5
[ 4.309944] shpchp: Standard Hot Plug PCI Controller Driver version: 0.4
[ 4.358630] Error: Driver 'pcspkr' is already registered, aborting...
[ 4.462658] HDA Intel 0000:00:1b.0: PCI INT A -> GSI 22 (level, low) -> IRQ 22
[ 4.462728] HDA Intel 0000:00:1b.0: setting latency timer to 64
[ 4.833301] hda_codec: ALC662 rev1: BIOS auto-probing.
[ 4.834990] input: HDA Digital PCBeep as /devices/pci0000:00/0000:00:1b.0/input/input7
[ 5.575428] Adding 3989496k swap on /dev/sda5. Priority:-1 extents:1 across:3989496k
[ 5.769853] EXT3 FS on sda1, internal journal
[ 5.896814] loop: module loaded
[ 7.232285] ADDRCONF(NETDEV_UP): eth1: link is not ready
[ 9.950650] e1000e: eth1 NIC Link is Up 100 Mbps Full Duplex, Flow Control: None
[ 9.950657] e1000e 0000:01:00.0: eth1: 10/100 speed: disabling TSO
[ 9.951362] ADDRCONF(NETDEV_CHANGE): eth1: link becomes ready
[ 20.794888] eth1: no IPv6 routers present
[ 72.391236] usb 1-4: new high speed USB device using ehci_hcd and address 4
[ 72.523843] usb 1-4: New USB device found, idVendor=0781, idProduct=5566
[ 72.523850] usb 1-4: New USB device strings: Mfr=1, Product=2, SerialNumber=3
[ 72.523855] usb 1-4: Product: Cruzer Slice
[ 72.523858] usb 1-4: Manufacturer: SanDisk
[ 72.523861] usb 1-4: SerialNumber: 200548584313BAB2E645
[ 72.524026] usb 1-4: configuration #1 chosen from 1 choice
[ 72.590657] Initializing USB Mass Storage driver...
[ 72.590989] scsi4 : SCSI emulation for USB Mass Storage devices
[ 72.591181] usb-storage: device found at 4
[ 72.591186] usb-storage: waiting for device to settle before scanning
[ 72.591209] usbcore: registered new interface driver usb-storage
[ 72.591216] USB Mass Storage support registered.
[ 77.581648] usb-storage: device scan complete
[ 77.582376] scsi 4:0:0:0: Direct-Access SanDisk Cruzer Slice 1.02 PQ: 0 ANSI: 2
[ 77.584230] sd 4:0:0:0: [sdb] 7813120 512-byte logical blocks: (4.00 GB/3.72 GiB)
[ 77.585715] sd 4:0:0:0: [sdb] Write Protect is off
[ 77.585722] sd 4:0:0:0: [sdb] Mode Sense: 03 00 00 00
[ 77.585725] sd 4:0:0:0: [sdb] Assuming drive cache: write through
[ 77.588340] sd 4:0:0:0: [sdb] Assuming drive cache: write through
[ 77.588396] sdb: sdb1
[ 77.598314] sd 4:0:0:0: [sdb] Assuming drive cache: write through
[ 77.598367] sd 4:0:0:0: [sdb] Attached SCSI removable disk
[ 101.110832] FAT: utf8 is not a recommended IO charset for FAT filesystems, filesystem will be case sensitive!
[ 0.000000] Initializing cgroup subsys cpuset
[ 0.000000] Initializing cgroup subsys cpu
[ 0.000000] Linux version 3.2.0-4-amd64 (debian-kernel@lists.debian.org) (gcc version 4.6.3 (Debian 4.6.3-14) ) #1 SMP Debian 3.2.41-2+deb7u2
[ 0.000000] Command line: BOOT_IMAGE=/boot/vmlinuz-3.2.0-4-amd64 root=UUID=54290ac6-2db5-424b-8cdb-e54f7e644b70 ro quiet
[ 0.000000] Disabled fast string operations
[ 0.000000] BIOS-provided physical RAM map:
[ 0.000000] BIOS-e820: 0000000000000000 - 000000000008f000 (usable)
[ 0.000000] BIOS-e820: 000000000008f000 - 0000000000090000 (reserved)
[ 0.000000] BIOS-e820: 0000000000090000 - 000000000009e800 (usable)
[ 0.000000] BIOS-e820: 000000000009e800 - 00000000000a0000 (reserved)
[ 0.000000] BIOS-e820: 00000000000e0000 - 0000000000100000 (reserved)
[ 0.000000] BIOS-e820: 0000000000100000 - 000000007ee98000 (usable)
[ 0.000000] BIOS-e820: 000000007ee98000 - 000000007eebf000 (reserved)
[ 0.000000] BIOS-e820: 000000007eebf000 - 000000007eeff000 (usable)
[ 0.000000] BIOS-e820: 000000007eeff000 - 000000007efbf000 (ACPI NVS)
[ 0.000000] BIOS-e820: 000000007efbf000 - 000000007eff2000 (usable)
[ 0.000000] BIOS-e820: 000000007eff2000 - 000000007efff000 (ACPI data)
[ 0.000000] BIOS-e820: 000000007efff000 - 000000007f000000 (usable)
[ 0.000000] BIOS-e820: 000000007f000000 - 0000000080000000 (reserved)
[ 0.000000] BIOS-e820: 00000000e0000000 - 00000000e4000000 (reserved)
[ 0.000000] BIOS-e820: 00000000ffe00000 - 0000000100000000 (reserved)
[ 0.000000] NX (Execute Disable) protection: active
[ 0.000000] SMBIOS 2.7 present.
[ 0.000000] DMI: /D2700DC , BIOS MUCDT10N.86A.0075.2013.0427.1548 04/27/2013
[ 0.000000] e820 update range: 0000000000000000 - 0000000000010000 (usable) ==> (reserved)
[ 0.000000] e820 remove range: 00000000000a0000 - 0000000000100000 (usable)
[ 0.000000] No AGP bridge found
[ 0.000000] last_pfn = 0x7f000 max_arch_pfn = 0x400000000
[ 0.000000] MTRR default type: uncachable
[ 0.000000] MTRR fixed ranges enabled:
[ 0.000000] 00000-9FFFF write-back
[ 0.000000] A0000-BFFFF uncachable
[ 0.000000] C0000-DFFFF write-protect
[ 0.000000] E0000-FFFFF uncachable
[ 0.000000] MTRR variable ranges enabled:
[ 0.000000] 0 base 000000000 mask F80000000 write-back
[ 0.000000] 1 base 07F000000 mask FFF000000 uncachable
[ 0.000000] 2 base 0FFE00000 mask FFFE00000 write-protect
[ 0.000000] 3 disabled
[ 0.000000] 4 disabled
[ 0.000000] 5 disabled
[ 0.000000] 6 disabled
[ 0.000000] x86 PAT enabled: cpu 0, old 0x7040600070406, new 0x7010600070106
[ 0.000000] found SMP MP-table at [ffff8800000fbe40] fbe40
[ 0.000000] initial memory mapped : 0 - 20000000
[ 0.000000] Base memory trampoline at [ffff880000099000] 99000 size 20480
[ 0.000000] init_memory_mapping: 0000000000000000-000000007f000000
[ 0.000000] 0000000000 - 007f000000 page 2M
[ 0.000000] kernel direct mapping tables up to 7f000000 @ 1fffd000-20000000
[ 0.000000] RAMDISK: 36c74000 - 37632000
[ 0.000000] ACPI: RSDP 00000000000f2390 00024 (v02 INTEL )
[ 0.000000] ACPI: XSDT 000000007effe120 0004C (v01 INTEL TIANO 0000004B 01000013)
[ 0.000000] ACPI: FACP 000000007eff6000 000F4 (v03 INTEL TIANO 0000004B MSFT 0100000D)
[ 0.000000] ACPI: DSDT 000000007eff8000 05B38 (v02 INTEL TIANO 0000004B MSFT 0100000D)
[ 0.000000] ACPI: FACS 000000007ef85000 00040
[ 0.000000] ACPI: SSDT 000000007eff7000 0043E (v01 INTEL TIANO 0000004B MSFT 0100000D)
[ 0.000000] ACPI: APIC 000000007eff5000 00084 (v02 INTEL TIANO 0000004B MSFT 0100000D)
[ 0.000000] ACPI: MCFG 000000007eff4000 0003C (v01 INTEL TIANO 0000004B MSFT 0100000D)
[ 0.000000] ACPI: HPET 000000007eff3000 00038 (v01 INTEL TIANO 0000004B MSFT 0100000D)
[ 0.000000] ACPI: Local APIC address 0xfee00000
[ 0.000000] No NUMA configuration found
[ 0.000000] Faking a node at 0000000000000000-000000007f000000
[ 0.000000] Initmem setup node 0 0000000000000000-000000007f000000
[ 0.000000] NODE_DATA [000000007efed000 - 000000007eff1fff]
[ 0.000000] [ffffea0000000000-ffffea0001bfffff] PMD -> [ffff88007c600000-ffff88007e1fffff] on node 0
[ 0.000000] Zone PFN ranges:
[ 0.000000] DMA 0x00000010 -> 0x00001000
[ 0.000000] DMA32 0x00001000 -> 0x00100000
[ 0.000000] Normal empty
[ 0.000000] Movable zone start PFN for each node
[ 0.000000] early_node_map[6] active PFN ranges
[ 0.000000] 0: 0x00000010 -> 0x0000008f
[ 0.000000] 0: 0x00000090 -> 0x0000009e
[ 0.000000] 0: 0x00000100 -> 0x0007ee98
[ 0.000000] 0: 0x0007eebf -> 0x0007eeff
[ 0.000000] 0: 0x0007efbf -> 0x0007eff2
[ 0.000000] 0: 0x0007efff -> 0x0007f000
[ 0.000000] On node 0 totalpages: 519833
[ 0.000000] DMA zone: 56 pages used for memmap
[ 0.000000] DMA zone: 5 pages reserved
[ 0.000000] DMA zone: 3920 pages, LIFO batch:0
[ 0.000000] DMA32 zone: 7056 pages used for memmap
[ 0.000000] DMA32 zone: 508796 pages, LIFO batch:31
[ 0.000000] ACPI: PM-Timer IO Port: 0x408
[ 0.000000] ACPI: Local APIC address 0xfee00000
[ 0.000000] ACPI: LAPIC (acpi_id[0x01] lapic_id[0x00] enabled)
[ 0.000000] ACPI: LAPIC (acpi_id[0x02] lapic_id[0x01] enabled)
[ 0.000000] ACPI: LAPIC (acpi_id[0x03] lapic_id[0x02] enabled)
[ 0.000000] ACPI: LAPIC (acpi_id[0x04] lapic_id[0x03] enabled)
[ 0.000000] ACPI: LAPIC_NMI (acpi_id[0x01] high level lint[0x1])
[ 0.000000] ACPI: LAPIC_NMI (acpi_id[0x02] high level lint[0x1])
[ 0.000000] ACPI: LAPIC_NMI (acpi_id[0x03] high level lint[0x1])
[ 0.000000] ACPI: LAPIC_NMI (acpi_id[0x04] high level lint[0x1])
[ 0.000000] ACPI: IOAPIC (id[0x08] address[0xfec00000] gsi_base[0])
[ 0.000000] IOAPIC[0]: apic_id 8, version 32, address 0xfec00000, GSI 0-23
[ 0.000000] ACPI: INT_SRC_OVR (bus 0 bus_irq 0 global_irq 2 dfl dfl)
[ 0.000000] ACPI: INT_SRC_OVR (bus 0 bus_irq 9 global_irq 9 high level)
[ 0.000000] ACPI: IRQ0 used by override.
[ 0.000000] ACPI: IRQ2 used by override.
[ 0.000000] ACPI: IRQ9 used by override.
[ 0.000000] Using ACPI (MADT) for SMP configuration information
[ 0.000000] ACPI: HPET id: 0x8086a201 base: 0xfed00000
[ 0.000000] SMP: Allowing 4 CPUs, 0 hotplug CPUs
[ 0.000000] nr_irqs_gsi: 40
[ 0.000000] PM: Registered nosave memory: 000000000008f000 - 0000000000090000
[ 0.000000] PM: Registered nosave memory: 000000000009e000 - 000000000009f000
[ 0.000000] PM: Registered nosave memory: 000000000009f000 - 00000000000a0000
[ 0.000000] PM: Registered nosave memory: 00000000000a0000 - 00000000000e0000
[ 0.000000] PM: Registered nosave memory: 00000000000e0000 - 0000000000100000
[ 0.000000] PM: Registered nosave memory: 000000007ee98000 - 000000007eebf000
[ 0.000000] PM: Registered nosave memory: 000000007eeff000 - 000000007efbf000
[ 0.000000] PM: Registered nosave memory: 000000007eff2000 - 000000007efff000
[ 0.000000] Allocating PCI resources starting at 80000000 (gap: 80000000:60000000)
[ 0.000000] Booting paravirtualized kernel on bare hardware
[ 0.000000] setup_percpu: NR_CPUS:512 nr_cpumask_bits:512 nr_cpu_ids:4 nr_node_ids:1
[ 0.000000] PERCPU: Embedded 28 pages/cpu @ffff88007ec00000 s82944 r8192 d23552 u524288
[ 0.000000] pcpu-alloc: s82944 r8192 d23552 u524288 alloc=1*2097152
[ 0.000000] pcpu-alloc: [0] 0 1 2 3
[ 0.000000] Built 1 zonelists in Node order, mobility grouping on. Total pages: 512716
[ 0.000000] Policy zone: DMA32
[ 0.000000] Kernel command line: BOOT_IMAGE=/boot/vmlinuz-3.2.0-4-amd64 root=UUID=54290ac6-2db5-424b-8cdb-e54f7e644b70 ro quiet
[ 0.000000] PID hash table entries: 4096 (order: 3, 32768 bytes)
[ 0.000000] Checking aperture...
[ 0.000000] No AGP bridge found
[ 0.000000] Calgary: detecting Calgary via BIOS EBDA area
[ 0.000000] Calgary: Unable to locate Rio Grande table in EBDA - bailing!
[ 0.000000] Memory: 2031720k/2080768k available (3420k kernel code, 1436k absent, 47612k reserved, 3318k data, 576k init)
[ 0.000000] Hierarchical RCU implementation.
[ 0.000000] RCU dyntick-idle grace-period acceleration is enabled.
[ 0.000000] NR_IRQS:33024 nr_irqs:712 16
[ 0.000000] Extended CMOS year: 2000
[ 0.000000] Console: colour VGA+ 80x25
[ 0.000000] console [tty0] enabled
[ 0.000000] hpet clockevent registered
[ 0.000000] Fast TSC calibration using PIT
[ 0.004000] Detected 2133.258 MHz processor.
[ 0.000005] Calibrating delay loop (skipped), value calculated using timer frequency.. 4266.51 BogoMIPS (lpj=8533032)
[ 0.000014] pid_max: default: 32768 minimum: 301
[ 0.000112] Security Framework initialized
[ 0.000121] AppArmor: AppArmor disabled by boot time parameter
[ 0.000481] Dentry cache hash table entries: 262144 (order: 9, 2097152 bytes)
[ 0.002076] Inode-cache hash table entries: 131072 (order: 8, 1048576 bytes)
[ 0.002831] Mount-cache hash table entries: 256
[ 0.003108] Initializing cgroup subsys cpuacct
[ 0.003119] Initializing cgroup subsys memory
[ 0.003146] Initializing cgroup subsys devices
[ 0.003154] Initializing cgroup subsys freezer
[ 0.003158] Initializing cgroup subsys net_cls
[ 0.003163] Initializing cgroup subsys blkio
[ 0.003180] Initializing cgroup subsys perf_event
[ 0.003236] Disabled fast string operations
[ 0.003244] CPU: Physical Processor ID: 0
[ 0.003247] CPU: Processor Core ID: 0
[ 0.003251] mce: CPU supports 5 MCE banks
[ 0.003264] CPU0: Thermal monitoring enabled (TM1)
[ 0.003271] using mwait in idle threads.
[ 0.003841] ACPI: Core revision 20110623
[ 0.011823] ..TIMER: vector=0x30 apic1=0 pin1=2 apic2=-1 pin2=-1
[ 0.051510] CPU0: Intel(R) Atom(TM) CPU D2700 @ 2.13GHz stepping 01
[ 0.159299] Performance Events: PEBS fmt0+, generic architected perfmon, Intel PMU driver.
[ 0.159311] ... version: 3
[ 0.159314] ... bit width: 40
[ 0.159318] ... generic registers: 2
[ 0.159321] ... value mask: 000000ffffffffff
[ 0.159324] ... max period: 000000007fffffff
[ 0.159327] ... fixed-purpose events: 3
[ 0.159330] ... event mask: 0000000700000003
[ 0.159829] NMI watchdog enabled, takes one hw-pmu counter.
[ 0.160200] Booting Node 0, Processors #1
[ 0.160206] smpboot cpu 1: start_ip = 99000
[ 0.247309] Disabled fast string operations
[ 0.267414] NMI watchdog enabled, takes one hw-pmu counter.
[ 0.267701] #2
[ 0.267704] smpboot cpu 2: start_ip = 99000
[ 0.355311] Disabled fast string operations
[ 0.375456] NMI watchdog enabled, takes one hw-pmu counter.
[ 0.375720] #3 Ok.
[ 0.375723] smpboot cpu 3: start_ip = 99000
[ 0.463312] Disabled fast string operations
[ 0.483464] NMI watchdog enabled, takes one hw-pmu counter.
[ 0.483512] Brought up 4 CPUs
[ 0.483517] Total of 4 processors activated (17066.93 BogoMIPS).
[ 0.484609] devtmpfs: initialized
[ 0.489004] PM: Registering ACPI NVS region at 7eeff000 (786432 bytes)
[ 0.489379] print_constraints: dummy:
[ 0.489515] NET: Registered protocol family 16
[ 0.489756] ACPI FADT declares the system doesn't support PCIe ASPM, so disable it
[ 0.489762] ACPI: bus type pci registered
[ 0.489936] PCI: MMCONFIG for domain 0000 [bus 00-3f] at [mem 0xe0000000-0xe3ffffff] (base 0xe0000000)
[ 0.489943] PCI: MMCONFIG at [mem 0xe0000000-0xe3ffffff] reserved in E820
[ 0.504080] PCI: Using configuration type 1 for base access
[ 0.506131] bio: create slab <bio-0> at 0
[ 0.506368] ACPI: Added _OSI(Module Device)
[ 0.506374] ACPI: Added _OSI(Processor Device)
[ 0.506378] ACPI: Added _OSI(3.0 _SCP Extensions)
[ 0.506383] ACPI: Added _OSI(Processor Aggregator Device)
[ 0.508284] ACPI: EC: Look up EC in DSDT
[ 0.510284] ACPI: Executed 1 blocks of module-level executable AML code
[ 0.535378] [Firmware Bug]: ACPI: BIOS _OSI(Linux) query ignored
[ 0.536187] ACPI: Interpreter enabled
[ 0.536195] ACPI: (supports S0 S3 S4 S5)
[ 0.536245] ACPI: Using IOAPIC for interrupt routing
[ 0.548138] ACPI: No dock devices found.
[ 0.548144] HEST: Table not found.
[ 0.548151] PCI: Using host bridge windows from ACPI; if necessary, use "pci=nocrs" and report a bug
[ 0.548669] \_SB_.PCI0:_OSC invalid UUID
[ 0.548672] _OSC request data:1 8 1f
[ 0.548682] ACPI: PCI Root Bridge [PCI0] (domain 0000 [bus 00-ff])
[ 0.549378] pci_root PNP0A08:00: host bridge window [io 0x0000-0x0cf7]
[ 0.549384] pci_root PNP0A08:00: host bridge window [io 0x0d00-0xffff]
[ 0.549390] pci_root PNP0A08:00: host bridge window [mem 0x000a0000-0x000bffff]
[ 0.549395] pci_root PNP0A08:00: host bridge window [mem 0x000c0000-0x000dffff]
[ 0.549400] pci_root PNP0A08:00: host bridge window [mem 0x000e0000-0x000effff]
[ 0.549405] pci_root PNP0A08:00: host bridge window [mem 0x000f0000-0x000fffff]
[ 0.549410] pci_root PNP0A08:00: host bridge window [mem 0x7f800000-0x7fffffff]
[ 0.549415] pci_root PNP0A08:00: host bridge window [mem 0x80000000-0xfebfffff]
[ 0.549420] pci_root PNP0A08:00: host bridge window [mem 0xfed40000-0xfed44fff]
[ 0.549449] pci 0000:00:00.0: [8086:0bf3] type 0 class 0x000600
[ 0.549508] pci 0000:00:02.0: [8086:0be2] type 0 class 0x000300
[ 0.549523] pci 0000:00:02.0: reg 10: [mem 0x80200000-0x802fffff]
[ 0.549532] pci 0000:00:02.0: reg 14: [io 0x30d0-0x30d7]
[ 0.549632] pci 0000:00:1b.0: [8086:27d8] type 0 class 0x000403
[ 0.549654] pci 0000:00:1b.0: reg 10: [mem 0x80400000-0x80403fff 64bit]
[ 0.549739] pci 0000:00:1b.0: PME# supported from D0 D3hot D3cold
[ 0.549776] pci 0000:00:1c.0: [8086:27d0] type 1 class 0x000604
[ 0.549866] pci 0000:00:1c.0: PME# supported from D0 D3hot D3cold
[ 0.549909] pci 0000:00:1d.0: [8086:27c8] type 0 class 0x000c03
[ 0.549975] pci 0000:00:1d.0: reg 20: [io 0x30a0-0x30bf]
[ 0.550031] pci 0000:00:1d.1: [8086:27c9] type 0 class 0x000c03
[ 0.550096] pci 0000:00:1d.1: reg 20: [io 0x3080-0x309f]
[ 0.550153] pci 0000:00:1d.2: [8086:27ca] type 0 class 0x000c03
[ 0.550218] pci 0000:00:1d.2: reg 20: [io 0x3060-0x307f]
[ 0.550273] pci 0000:00:1d.3: [8086:27cb] type 0 class 0x000c03
[ 0.550325] pci 0000:00:1d.3: reg 20: [io 0x3040-0x305f]
[ 0.550392] pci 0000:00:1d.7: [8086:27cc] type 0 class 0x000c03
[ 0.550418] pci 0000:00:1d.7: reg 10: [mem 0x80304400-0x803047ff]
[ 0.550521] pci 0000:00:1d.7: PME# supported from D0 D3hot D3cold
[ 0.550553] pci 0000:00:1e.0: [8086:2448] type 1 class 0x000604
[ 0.550637] pci 0000:00:1f.0: [8086:27bc] type 0 class 0x000601
[ 0.550732] pci 0000:00:1f.0: [Firmware Bug]: TigerPoint LPC.BM_STS cleared
[ 0.550794] pci 0000:00:1f.2: [8086:27c1] type 0 class 0x000106
[ 0.550815] pci 0000:00:1f.2: reg 10: [io 0x30c8-0x30cf]
[ 0.550827] pci 0000:00:1f.2: reg 14: [io 0x30dc-0x30df]
[ 0.550839] pci 0000:00:1f.2: reg 18: [io 0x30c0-0x30c7]
[ 0.550851] pci 0000:00:1f.2: reg 1c: [io 0x30d8-0x30db]
[ 0.550863] pci 0000:00:1f.2: reg 20: [io 0x3020-0x302f]
[ 0.550876] pci 0000:00:1f.2: reg 24: [mem 0x80304000-0x803043ff]
[ 0.550921] pci 0000:00:1f.2: PME# supported from D3hot
[ 0.550949] pci 0000:00:1f.3: [8086:27da] type 0 class 0x000c05
[ 0.551013] pci 0000:00:1f.3: reg 20: [io 0x3000-0x301f]
[ 0.551213] pci 0000:01:00.0: [8086:10d3] type 0 class 0x000200
[ 0.551247] pci 0000:01:00.0: reg 10: [mem 0x80120000-0x8013ffff]
[ 0.551272] pci 0000:01:00.0: reg 14: [mem 0x80100000-0x8011ffff]
[ 0.551300] pci 0000:01:00.0: reg 18: [io 0x2000-0x201f]
[ 0.551346] pci 0000:01:00.0: reg 1c: [mem 0x80140000-0x80143fff]
[ 0.551536] pci 0000:01:00.0: PME# supported from D0 D3hot D3cold
[ 0.551630] pci 0000:00:1c.0: PCI bridge to [bus 01-01]
[ 0.551638] pci 0000:00:1c.0: bridge window [io 0x2000-0x2fff]
[ 0.551645] pci 0000:00:1c.0: bridge window [mem 0x80100000-0x801fffff]
[ 0.551701] pci 0000:02:00.0: [104c:ac23] type 1 class 0x000604
[ 0.551840] pci 0000:00:1e.0: PCI bridge to [bus 02-03] (subtractive decode)
[ 0.551847] pci 0000:00:1e.0: bridge window [io 0x1000-0x1fff]
[ 0.551854] pci 0000:00:1e.0: bridge window [mem 0x80000000-0x800fffff]
[ 0.551864] pci 0000:00:1e.0: bridge window [io 0x0000-0x0cf7] (subtractive decode)
[ 0.551870] pci 0000:00:1e.0: bridge window [io 0x0d00-0xffff] (subtractive decode)
[ 0.551875] pci 0000:00:1e.0: bridge window [mem 0x000a0000-0x000bffff] (subtractive decode)
[ 0.551881] pci 0000:00:1e.0: bridge window [mem 0x000c0000-0x000dffff] (subtractive decode)
[ 0.551886] pci 0000:00:1e.0: bridge window [mem 0x000e0000-0x000effff] (subtractive decode)
[ 0.551892] pci 0000:00:1e.0: bridge window [mem 0x000f0000-0x000fffff] (subtractive decode)
[ 0.551898] pci 0000:00:1e.0: bridge window [mem 0x7f800000-0x7fffffff] (subtractive decode)
[ 0.551903] pci 0000:00:1e.0: bridge window [mem 0x80000000-0xfebfffff] (subtractive decode)
[ 0.551909] pci 0000:00:1e.0: bridge window [mem 0xfed40000-0xfed44fff] (subtractive decode)
[ 0.551968] pci 0000:03:00.0: [1106:3053] type 0 class 0x000200
[ 0.552000] pci 0000:03:00.0: reg 10: [io 0x1300-0x13ff]
[ 0.552018] pci 0000:03:00.0: reg 14: [mem 0x80000300-0x800003ff]
[ 0.552132] pci 0000:03:00.0: supports D1 D2
[ 0.552136] pci 0000:03:00.0: PME# supported from D0 D1 D2 D3hot D3cold
[ 0.552175] pci 0000:03:01.0: [1106:3053] type 0 class 0x000200
[ 0.552205] pci 0000:03:01.0: reg 10: [io 0x1200-0x12ff]
[ 0.552223] pci 0000:03:01.0: reg 14: [mem 0x80000200-0x800002ff]
[ 0.552339] pci 0000:03:01.0: supports D1 D2
[ 0.552343] pci 0000:03:01.0: PME# supported from D0 D1 D2 D3hot D3cold
[ 0.552382] pci 0000:03:02.0: [1106:3053] type 0 class 0x000200
[ 0.552412] pci 0000:03:02.0: reg 10: [io 0x1100-0x11ff]
[ 0.552431] pci 0000:03:02.0: reg 14: [mem 0x80000100-0x800001ff]
[ 0.552544] pci 0000:03:02.0: supports D1 D2
[ 0.552549] pci 0000:03:02.0: PME# supported from D0 D1 D2 D3hot D3cold
[ 0.552587] pci 0000:03:03.0: [1106:3053] type 0 class 0x000200
[ 0.552617] pci 0000:03:03.0: reg 10: [io 0x1000-0x10ff]
[ 0.552634] pci 0000:03:03.0: reg 14: [mem 0x80000000-0x800000ff]
[ 0.552747] pci 0000:03:03.0: supports D1 D2
[ 0.552752] pci 0000:03:03.0: PME# supported from D0 D1 D2 D3hot D3cold
[ 0.552826] pci 0000:02:00.0: PCI bridge to [bus 03-03]
[ 0.552836] pci 0000:02:00.0: bridge window [io 0x1000-0x1fff]
[ 0.552845] pci 0000:02:00.0: bridge window [mem 0x80000000-0x800fffff]
[ 0.552875] ACPI: PCI Interrupt Routing Table [\_SB_.PCI0._PRT]
[ 0.553049] ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.P0P1._PRT]
[ 0.553375] ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.RP01._PRT]
[ 0.553623] \_SB_.PCI0:_OSC invalid UUID
[ 0.553626] _OSC request data:1 1f 1f
[ 0.553635] pci0000:00: Requesting ACPI _OSC control (0x1d)
[ 0.553739] \_SB_.PCI0:_OSC invalid UUID
[ 0.553742] _OSC request data:1 0 1d
[ 0.553751] pci0000:00: ACPI _OSC request failed (AE_ERROR), returned control mask: 0x1d
[ 0.553754] ACPI _OSC control for PCIe not granted, disabling ASPM
[ 0.561973] ACPI: PCI Interrupt Link [LNKA] (IRQs 1 3 4 5 6 7 10 12 14 15) *11
[ 0.562106] ACPI: PCI Interrupt Link [LNKB] (IRQs 1 3 4 5 6 7 11 12 14 15) *0, disabled.
[ 0.562236] ACPI: PCI Interrupt Link [LNKC] (IRQs 1 3 4 5 6 7 10 12 14 15) *9
[ 0.562363] ACPI: PCI Interrupt Link [LNKD] (IRQs 1 3 4 5 6 7 *11 12 14 15)
[ 0.562491] ACPI: PCI Interrupt Link [LNKE] (IRQs 1 3 4 5 6 7 *10 12 14 15)
[ 0.562618] ACPI: PCI Interrupt Link [LNKF] (IRQs 1 3 4 5 6 7 *11 12 14 15)
[ 0.562745] ACPI: PCI Interrupt Link [LNKG] (IRQs 1 3 4 5 6 7 10 12 14 15) *9
[ 0.562874] ACPI: PCI Interrupt Link [LNKH] (IRQs 1 3 4 5 6 7 11 12 14 15) *10
[ 0.563140] vgaarb: device added: PCI:0000:00:02.0,decodes=io+mem,owns=io+mem,locks=none
[ 0.563162] vgaarb: loaded
[ 0.563165] vgaarb: bridge control possible 0000:00:02.0
[ 0.563271] PCI: Using ACPI for IRQ routing
[ 0.564987] PCI: pci_cache_line_size set to 64 bytes
[ 0.565172] reserve RAM buffer: 000000000008f000 - 000000000008ffff
[ 0.565177] reserve RAM buffer: 000000000009e800 - 000000000009ffff
[ 0.565182] reserve RAM buffer: 000000007ee98000 - 000000007fffffff
[ 0.565187] reserve RAM buffer: 000000007eeff000 - 000000007fffffff
[ 0.565192] reserve RAM buffer: 000000007eff2000 - 000000007fffffff
[ 0.565196] reserve RAM buffer: 000000007f000000 - 000000007fffffff
[ 0.565451] hpet0: at MMIO 0xfed00000, IRQs 2, 8, 0
[ 0.565460] hpet0: 3 comparators, 64-bit 14.318180 MHz counter
[ 0.567500] Switching to clocksource hpet
[ 0.571586] pnp: PnP ACPI init
[ 0.571621] ACPI: bus type pnp registered
[ 0.572003] pnp 00:00: [bus 00-ff]
[ 0.572009] pnp 00:00: [io 0x0000-0x0cf7 window]
[ 0.572014] pnp 00:00: [io 0x0cf8-0x0cff]
[ 0.572019] pnp 00:00: [io 0x0d00-0xffff window]
[ 0.572024] pnp 00:00: [mem 0x000a0000-0x000bffff window]
[ 0.572029] pnp 00:00: [mem 0x000c0000-0x000dffff window]
[ 0.572034] pnp 00:00: [mem 0x000e0000-0x000effff window]
[ 0.572039] pnp 00:00: [mem 0x000f0000-0x000fffff window]
[ 0.572044] pnp 00:00: [mem 0x7f800000-0x7fffffff window]
[ 0.572049] pnp 00:00: [mem 0x80000000-0xfebfffff window]
[ 0.572054] pnp 00:00: [mem 0xfed40000-0xfed44fff window]
[ 0.572166] pnp 00:00: Plug and Play ACPI device, IDs PNP0a08 PNP0a03 (active)
[ 0.572210] pnp 00:01: [io 0x0000-0x001f]
[ 0.572215] pnp 00:01: [io 0x0081-0x0091]
[ 0.572222] pnp 00:01: [io 0x0093-0x009f]
[ 0.572226] pnp 00:01: [io 0x00c0-0x00df]
[ 0.572231] pnp 00:01: [dma 4]
[ 0.572292] pnp 00:01: Plug and Play ACPI device, IDs PNP0200 (active)
[ 0.572316] pnp 00:02: [mem 0xff000000-0xffffffff]
[ 0.572375] pnp 00:02: Plug and Play ACPI device, IDs INT0800 (active)
[ 0.572556] pnp 00:03: [mem 0xfed00000-0xfed003ff]
[ 0.572658] system 00:03: [mem 0xfed00000-0xfed003ff] has been reserved
[ 0.572666] system 00:03: Plug and Play ACPI device, IDs PNP0103 PNP0c01 (active)
[ 0.572695] pnp 00:04: [io 0x00f0]
[ 0.572713] pnp 00:04: [irq 13]
[ 0.572778] pnp 00:04: Plug and Play ACPI device, IDs PNP0c04 (active)
[ 0.572808] pnp 00:05: [io 0x002e-0x002f]
[ 0.572813] pnp 00:05: [io 0x004e-0x004f]
[ 0.572817] pnp 00:05: [io 0x0061]
[ 0.572821] pnp 00:05: [io 0x0063]
[ 0.572825] pnp 00:05: [io 0x0065]
[ 0.572829] pnp 00:05: [io 0x0067]
[ 0.572833] pnp 00:05: [io 0x0070]
[ 0.572838] pnp 00:05: [io 0x0080]
[ 0.572842] pnp 00:05: [io 0x0092]
[ 0.572846] pnp 00:05: [io 0x00b2-0x00b3]
[ 0.572850] pnp 00:05: [io 0x0680-0x069f]
[ 0.572855] pnp 00:05: [io 0xffff]
[ 0.572859] pnp 00:05: [io 0xffff]
[ 0.572863] pnp 00:05: [io 0xffff]
[ 0.572867] pnp 00:05: [io 0x0400-0x047f]
[ 0.572871] pnp 00:05: [io 0x0500-0x057f]
[ 0.572876] pnp 00:05: [io 0x0600-0x061f]
[ 0.573000] system 00:05: [io 0x0680-0x069f] has been reserved
[ 0.573006] system 00:05: [io 0xffff] has been reserved
[ 0.573012] system 00:05: [io 0xffff] has been reserved
[ 0.573018] system 00:05: [io 0xffff] has been reserved
[ 0.573023] system 00:05: [io 0x0400-0x047f] has been reserved
[ 0.573029] system 00:05: [io 0x0500-0x057f] has been reserved
[ 0.573035] system 00:05: [io 0x0600-0x061f] has been reserved
[ 0.573042] system 00:05: Plug and Play ACPI device, IDs PNP0c02 (active)
[ 0.573109] pnp 00:06: [io 0x06a0-0x06af]
[ 0.573114] pnp 00:06: [io 0x06b0-0x06ff]
[ 0.573206] system 00:06: [io 0x06a0-0x06af] has been reserved
[ 0.573212] system 00:06: [io 0x06b0-0x06ff] has been reserved
[ 0.573219] system 00:06: Plug and Play ACPI device, IDs PNP0c02 (active)
[ 0.573243] pnp 00:07: [io 0x0070-0x0077]
[ 0.573257] pnp 00:07: [irq 8]
[ 0.573315] pnp 00:07: Plug and Play ACPI device, IDs PNP0b00 (active)
[ 0.574047] pnp 00:08: [mem 0xfed1c000-0xfed1ffff]
[ 0.574052] pnp 00:08: [mem 0x00000000-0x00003fff]
[ 0.574060] pnp 00:08: [mem 0x00000000-0x00000fff]
[ 0.574065] pnp 00:08: [mem 0x00000000-0x00000fff]
[ 0.574070] pnp 00:08: [mem 0x00000000-0xffffffffffffffff disabled]
[ 0.574075] pnp 00:08: [mem 0xfed45000-0xfed8ffff]
[ 0.574196] system 00:08: [mem 0xfed1c000-0xfed1ffff] has been reserved
[ 0.574203] system 00:08: [mem 0x00000000-0x00003fff] could not be reserved
[ 0.574209] system 00:08: [mem 0x00000000-0x00000fff] could not be reserved
[ 0.574215] system 00:08: [mem 0x00000000-0x00000fff] could not be reserved
[ 0.574221] system 00:08: [mem 0xfed45000-0xfed8ffff] has been reserved
[ 0.574228] system 00:08: Plug and Play ACPI device, IDs PNP0c02 (active)
[ 0.574549] pnp: PnP ACPI: found 9 devices
[ 0.574553] ACPI: ACPI bus type pnp unregistered
[ 0.584656] PCI: max bus depth: 2 pci_try_num: 3
[ 0.584711] pci 0000:00:1c.0: BAR 15: assigned [mem 0x80500000-0x806fffff 64bit pref]
[ 0.584718] pci 0000:00:1c.0: PCI bridge to [bus 01-01]
[ 0.584724] pci 0000:00:1c.0: bridge window [io 0x2000-0x2fff]
[ 0.584732] pci 0000:00:1c.0: bridge window [mem 0x80100000-0x801fffff]
[ 0.584739] pci 0000:00:1c.0: bridge window [mem 0x80500000-0x806fffff 64bit pref]
[ 0.584751] pci 0000:02:00.0: PCI bridge to [bus 03-03]
[ 0.584757] pci 0000:02:00.0: bridge window [io 0x1000-0x1fff]
[ 0.584765] pci 0000:02:00.0: bridge window [mem 0x80000000-0x800fffff]
[ 0.584780] pci 0000:00:1e.0: PCI bridge to [bus 02-03]
[ 0.584785] pci 0000:00:1e.0: bridge window [io 0x1000-0x1fff]
[ 0.584792] pci 0000:00:1e.0: bridge window [mem 0x80000000-0x800fffff]
[ 0.584835] pci 0000:00:1c.0: setting latency timer to 64
[ 0.584847] pci 0000:00:1e.0: setting latency timer to 64
[ 0.584862] pci_bus 0000:00: resource 4 [io 0x0000-0x0cf7]
[ 0.584867] pci_bus 0000:00: resource 5 [io 0x0d00-0xffff]
[ 0.584872] pci_bus 0000:00: resource 6 [mem 0x000a0000-0x000bffff]
[ 0.584877] pci_bus 0000:00: resource 7 [mem 0x000c0000-0x000dffff]
[ 0.584882] pci_bus 0000:00: resource 8 [mem 0x000e0000-0x000effff]
[ 0.584886] pci_bus 0000:00: resource 9 [mem 0x000f0000-0x000fffff]
[ 0.584891] pci_bus 0000:00: resource 10 [mem 0x7f800000-0x7fffffff]
[ 0.584896] pci_bus 0000:00: resource 11 [mem 0x80000000-0xfebfffff]
[ 0.584901] pci_bus 0000:00: resource 12 [mem 0xfed40000-0xfed44fff]
[ 0.584907] pci_bus 0000:01: resource 0 [io 0x2000-0x2fff]
[ 0.584911] pci_bus 0000:01: resource 1 [mem 0x80100000-0x801fffff]
[ 0.584916] pci_bus 0000:01: resource 2 [mem 0x80500000-0x806fffff 64bit pref]
[ 0.584922] pci_bus 0000:02: resource 0 [io 0x1000-0x1fff]
[ 0.584927] pci_bus 0000:02: resource 1 [mem 0x80000000-0x800fffff]
[ 0.584932] pci_bus 0000:02: resource 4 [io 0x0000-0x0cf7]
[ 0.584936] pci_bus 0000:02: resource 5 [io 0x0d00-0xffff]
[ 0.584941] pci_bus 0000:02: resource 6 [mem 0x000a0000-0x000bffff]
[ 0.584946] pci_bus 0000:02: resource 7 [mem 0x000c0000-0x000dffff]
[ 0.584951] pci_bus 0000:02: resource 8 [mem 0x000e0000-0x000effff]
[ 0.584955] pci_bus 0000:02: resource 9 [mem 0x000f0000-0x000fffff]
[ 0.584960] pci_bus 0000:02: resource 10 [mem 0x7f800000-0x7fffffff]
[ 0.584965] pci_bus 0000:02: resource 11 [mem 0x80000000-0xfebfffff]
[ 0.584970] pci_bus 0000:02: resource 12 [mem 0xfed40000-0xfed44fff]
[ 0.584975] pci_bus 0000:03: resource 0 [io 0x1000-0x1fff]
[ 0.584980] pci_bus 0000:03: resource 1 [mem 0x80000000-0x800fffff]
[ 0.585135] NET: Registered protocol family 2
[ 0.585365] IP route cache hash table entries: 65536 (order: 7, 524288 bytes)
[ 0.586951] TCP established hash table entries: 262144 (order: 10, 4194304 bytes)
[ 0.589958] TCP bind hash table entries: 65536 (order: 8, 1048576 bytes)
[ 0.590655] TCP: Hash tables configured (established 262144 bind 65536)
[ 0.590661] TCP reno registered
[ 0.590688] UDP hash table entries: 1024 (order: 3, 32768 bytes)
[ 0.590722] UDP-Lite hash table entries: 1024 (order: 3, 32768 bytes)
[ 0.591016] NET: Registered protocol family 1
[ 0.591054] pci 0000:00:02.0: Boot video device
[ 0.607640] PCI: CLS 64 bytes, default 64
[ 0.607758] Unpacking initramfs...
[ 1.019335] Freeing initrd memory: 9976k freed
[ 1.028155] audit: initializing netlink socket (disabled)
[ 1.028178] type=2000 audit(1369198664.872:1): initialized
[ 1.050559] HugeTLB registered 2 MB page size, pre-allocated 0 pages
[ 1.051579] VFS: Disk quotas dquot_6.5.2
[ 1.051647] Dquot-cache hash table entries: 512 (order 0, 4096 bytes)
[ 1.051793] msgmni has been set to 3987
[ 1.052149] alg: No test for stdrng (krng)
[ 1.052218] Block layer SCSI generic (bsg) driver version 0.4 loaded (major 253)
[ 1.052225] io scheduler noop registered
[ 1.052228] io scheduler deadline registered
[ 1.052268] io scheduler cfq registered (default)
[ 1.052444] pcieport 0000:00:1c.0: setting latency timer to 64
[ 1.052508] pcieport 0000:00:1c.0: irq 40 for MSI/MSI-X
[ 1.052700] pci_hotplug: PCI Hot Plug PCI Core version: 0.5
[ 1.052754] pciehp: PCI Express Hot Plug Controller Driver version: 0.4
[ 1.052758] acpiphp: ACPI Hot Plug PCI Controller Driver version: 0.5
[ 1.053342] intel_idle: does not run on family 6 model 54
[ 1.053386] ERST: Table is not found!
[ 1.053389] GHES: HEST is not enabled!
[ 1.053515] Serial: 8250/16550 driver, 4 ports, IRQ sharing enabled
[ 1.228159] Linux agpgart interface v0.103
[ 1.228453] i8042: PNP: No PS/2 controller found. Probing ports directly.
[ 1.231060] serio: i8042 KBD port at 0x60,0x64 irq 1
[ 1.231078] serio: i8042 AUX port at 0x60,0x64 irq 12
[ 1.231439] mousedev: PS/2 mouse device common for all mice
[ 1.231518] rtc_cmos 00:07: RTC can wake from S4
[ 1.231750] rtc_cmos 00:07: rtc core: registered rtc_cmos as rtc0
[ 1.231789] rtc0: alarms up to one month, y3k, 242 bytes nvram, hpet irqs
[ 1.231812] cpuidle: using governor ladder
[ 1.231816] cpuidle: using governor menu
[ 1.232257] TCP cubic registered
[ 1.232372] NET: Registered protocol family 10
[ 1.233414] Mobile IPv6
[ 1.233420] NET: Registered protocol family 17
[ 1.233429] Registering the dns_resolver key type
[ 1.233748] PM: Hibernation image not present or could not be loaded.
[ 1.233773] registered taskstats version 1
[ 1.234596] rtc_cmos 00:07: setting system clock to 2013-05-22 04:57:45 UTC (1369198665)
[ 1.234728] Initializing network drop monitor service
[ 1.237384] Freeing unused kernel memory: 576k freed
[ 1.237609] Write protecting the kernel read-only data: 6144k
[ 1.244090] Freeing unused kernel memory: 660k freed
[ 1.250984] Freeing unused kernel memory: 676k freed
[ 1.275920] udevd[57]: starting version 175
[ 1.333155] usbcore: registered new interface driver usbfs
[ 1.333218] usbcore: registered new interface driver hub
[ 1.339492] usbcore: registered new device driver usb
[ 1.340848] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
[ 1.340935] ehci_hcd 0000:00:1d.7: setting latency timer to 64
[ 1.340945] ehci_hcd 0000:00:1d.7: EHCI Host Controller
[ 1.341023] ehci_hcd 0000:00:1d.7: new USB bus registered, assigned bus number 1
[ 1.341086] ehci_hcd 0000:00:1d.7: using broken periodic workaround
[ 1.341106] ehci_hcd 0000:00:1d.7: debug port 1
[ 1.345003] ehci_hcd 0000:00:1d.7: cache line size of 64 is not supported
[ 1.345838] e1000e: Intel(R) PRO/1000 Network Driver - 1.5.1-k
[ 1.345846] e1000e: Copyright(c) 1999 - 2011 Intel Corporation.
[ 1.345906] e1000e 0000:01:00.0: Disabling ASPM L0s L1
[ 1.346027] e1000e 0000:01:00.0: setting latency timer to 64
[ 1.346397] e1000e 0000:01:00.0: irq 41 for MSI/MSI-X
[ 1.346416] e1000e 0000:01:00.0: irq 42 for MSI/MSI-X
[ 1.346433] e1000e 0000:01:00.0: irq 43 for MSI/MSI-X
[ 1.351105] ehci_hcd 0000:00:1d.7: irq 23, io mem 0x80304400
[ 1.361163] SCSI subsystem initialized
[ 1.363913] ehci_hcd 0000:00:1d.7: USB 2.0 started, EHCI 1.00
[ 1.363994] usb usb1: New USB device found, idVendor=1d6b, idProduct=0002
[ 1.364002] usb usb1: New USB device strings: Mfr=3, Product=2, SerialNumber=1
[ 1.364009] usb usb1: Product: EHCI Host Controller
[ 1.364014] usb usb1: Manufacturer: Linux 3.2.0-4-amd64 ehci_hcd
[ 1.364020] usb usb1: SerialNumber: 0000:00:1d.7
[ 1.364439] hub 1-0:1.0: USB hub found
[ 1.364457] hub 1-0:1.0: 8 ports detected
[ 1.367465] uhci_hcd: USB Universal Host Controller Interface driver
[ 1.369362] uhci_hcd 0000:00:1d.0: setting latency timer to 64
[ 1.369375] uhci_hcd 0000:00:1d.0: UHCI Host Controller
[ 1.369423] uhci_hcd 0000:00:1d.0: new USB bus registered, assigned bus number 2
[ 1.369483] uhci_hcd 0000:00:1d.0: irq 23, io base 0x000030a0
[ 1.369614] usb usb2: New USB device found, idVendor=1d6b, idProduct=0001
[ 1.369622] usb usb2: New USB device strings: Mfr=3, Product=2, SerialNumber=1
[ 1.369631] usb usb2: Product: UHCI Host Controller
[ 1.369637] usb usb2: Manufacturer: Linux 3.2.0-4-amd64 uhci_hcd
[ 1.369643] usb usb2: SerialNumber: 0000:00:1d.0
[ 1.370101] hub 2-0:1.0: USB hub found
[ 1.370124] hub 2-0:1.0: 2 ports detected
[ 1.370393] uhci_hcd 0000:00:1d.1: setting latency timer to 64
[ 1.370403] uhci_hcd 0000:00:1d.1: UHCI Host Controller
[ 1.370433] uhci_hcd 0000:00:1d.1: new USB bus registered, assigned bus number 3
[ 1.370536] uhci_hcd 0000:00:1d.1: irq 19, io base 0x00003080
[ 1.370670] usb usb3: New USB device found, idVendor=1d6b, idProduct=0001
[ 1.370679] usb usb3: New USB device strings: Mfr=3, Product=2, SerialNumber=1
[ 1.370686] usb usb3: Product: UHCI Host Controller
[ 1.370691] usb usb3: Manufacturer: Linux 3.2.0-4-amd64 uhci_hcd
[ 1.370697] usb usb3: SerialNumber: 0000:00:1d.1
[ 1.371139] hub 3-0:1.0: USB hub found
[ 1.371156] hub 3-0:1.0: 2 ports detected
[ 1.371413] uhci_hcd 0000:00:1d.2: setting latency timer to 64
[ 1.371424] uhci_hcd 0000:00:1d.2: UHCI Host Controller
[ 1.371461] uhci_hcd 0000:00:1d.2: new USB bus registered, assigned bus number 4
[ 1.371597] uhci_hcd 0000:00:1d.2: irq 18, io base 0x00003060
[ 1.371713] usb usb4: New USB device found, idVendor=1d6b, idProduct=0001
[ 1.371720] usb usb4: New USB device strings: Mfr=3, Product=2, SerialNumber=1
[ 1.371726] usb usb4: Product: UHCI Host Controller
[ 1.371731] usb usb4: Manufacturer: Linux 3.2.0-4-amd64 uhci_hcd
[ 1.371737] usb usb4: SerialNumber: 0000:00:1d.2
[ 1.372139] hub 4-0:1.0: USB hub found
[ 1.372154] hub 4-0:1.0: 2 ports detected
[ 1.372383] uhci_hcd 0000:00:1d.3: setting latency timer to 64
[ 1.372392] uhci_hcd 0000:00:1d.3: UHCI Host Controller
[ 1.372416] uhci_hcd 0000:00:1d.3: new USB bus registered, assigned bus number 5
[ 1.372492] uhci_hcd 0000:00:1d.3: irq 16, io base 0x00003040
[ 1.372610] usb usb5: New USB device found, idVendor=1d6b, idProduct=0001
[ 1.372618] usb usb5: New USB device strings: Mfr=3, Product=2, SerialNumber=1
[ 1.372625] usb usb5: Product: UHCI Host Controller
[ 1.372630] usb usb5: Manufacturer: Linux 3.2.0-4-amd64 uhci_hcd
[ 1.372637] usb usb5: SerialNumber: 0000:00:1d.3
[ 1.373109] hub 5-0:1.0: USB hub found
[ 1.373129] hub 5-0:1.0: 2 ports detected
[ 1.380031] libata version 3.00 loaded.
[ 1.382726] ahci 0000:00:1f.2: version 3.0
[ 1.382860] ahci 0000:00:1f.2: irq 44 for MSI/MSI-X
[ 1.383019] ahci: SSS flag set, parallel bus scan disabled
[ 1.383069] ahci 0000:00:1f.2: AHCI 0001.0100 32 slots 4 ports 3 Gbps 0x3 impl SATA mode
[ 1.383080] ahci 0000:00:1f.2: flags: 64bit ncq stag pm led clo pio slum part
[ 1.383091] ahci 0000:00:1f.2: setting latency timer to 64
[ 1.389502] via_rhine: v1.10-LK1.5.0 2010-10-09 Written by Donald Becker
[ 1.389650] via-rhine 0000:03:00.0: (unregistered net_device): Woke system up. Reason: Unknown
[ 1.389663] via-rhine 0000:03:00.0: (unregistered net_device): Reset not complete yet. Trying harder.
[ 1.390658] scsi0 : ahci
[ 1.391323] scsi1 : ahci
[ 1.392055] scsi2 : ahci
[ 1.392211] via-rhine 0000:03:00.0: (unregistered net_device): Invalid MAC address: ff:ff:ff:ff:ff:ff
[ 1.392271] via-rhine 0000:03:00.0: (unregistered net_device): Using random MAC address: ee:fb:b6:37:67:8e
[ 1.392360] scsi3 : ahci
[ 1.392914] ata1: SATA max UDMA/133 abar m1024@0x80304000 port 0x80304100 irq 44
[ 1.392924] ata2: SATA max UDMA/133 abar m1024@0x80304000 port 0x80304180 irq 44
[ 1.392931] ata3: DUMMY
[ 1.392935] ata4: DUMMY
[ 1.393269] via-rhine 0000:03:00.0: eth0: VIA Rhine III (Management Adapter) at 0x11300, ee:fb:b6:37:67:8e, IRQ 20
[ 1.397885] via-rhine 0000:03:01.0: (unregistered net_device): Woke system up. Reason: Unknown
[ 1.397901] via-rhine 0000:03:01.0: (unregistered net_device): Reset not complete yet. Trying harder.
[ 1.400461] via-rhine 0000:03:01.0: (unregistered net_device): Invalid MAC address: ff:ff:ff:ff:ff:ff
[ 1.400521] via-rhine 0000:03:01.0: (unregistered net_device): Using random MAC address: 9a:ab:46:bd:3e:6b
[ 1.403678] via-rhine 0000:03:01.0: eth1: VIA Rhine III (Management Adapter) at 0x11200, 9a:ab:46:bd:3e:6b, IRQ 21
[ 1.407436] via-rhine 0000:03:02.0: (unregistered net_device): Woke system up. Reason: Unknown
[ 1.407446] via-rhine 0000:03:02.0: (unregistered net_device): Reset not complete yet. Trying harder.
[ 1.409909] via-rhine 0000:03:02.0: (unregistered net_device): Invalid MAC address: ff:ff:ff:ff:ff:ff
[ 1.409963] via-rhine 0000:03:02.0: (unregistered net_device): Using random MAC address: e2:48:cb:ae:c0:42
[ 1.410984] via-rhine 0000:03:02.0: eth2: VIA Rhine III (Management Adapter) at 0x11100, e2:48:cb:ae:c0:42, IRQ 22
[ 1.421499] via-rhine 0000:03:03.0: eth3: VIA Rhine III (Management Adapter) at 0x11000, 00:00:24:cf:a5:d7, IRQ 23
[ 1.422277] via-rhine 0000:03:03.0: eth3: MII PHY found at address 1, status 0x7849 advertising 05e1 Link 0000
[ 1.456225] e1000e 0000:01:00.0: eth4: (PCI Express:2.5GT/s:Width x1) 00:22:4d:81:9e:39
[ 1.456232] e1000e 0000:01:00.0: eth4: Intel(R) PRO/1000 Network Connection
[ 1.456253] e1000e 0000:01:00.0: eth4: MAC: 3, PHY: 8, PBA No: FFFFFF-0FF
[ 1.711576] ata1: SATA link up 1.5 Gbps (SStatus 113 SControl 300)
[ 1.731566] usb 1-4: new high-speed USB device number 3 using ehci_hcd
[ 1.752106] ata1.00: HPA detected: current 625140335, native 625142448
[ 1.752115] ata1.00: ATA-7: ST3320620AS, 3.AAK, max UDMA/133
[ 1.752121] ata1.00: 625140335 sectors, multi 16: LBA48 NCQ (depth 31/32)
[ 1.810413] ata1.00: configured for UDMA/133
[ 1.810649] scsi 0:0:0:0: Direct-Access ATA ST3320620AS 3.AA PQ: 0 ANSI: 5
[ 1.864437] usb 1-4: New USB device found, idVendor=0781, idProduct=5566
[ 1.864444] usb 1-4: New USB device strings: Mfr=1, Product=2, SerialNumber=3
[ 1.864449] usb 1-4: Product: Cruzer Slice
[ 1.864452] usb 1-4: Manufacturer: SanDisk
[ 1.864456] usb 1-4: SerialNumber: 200548584313BAB2E645
[ 1.869646] Initializing USB Mass Storage driver...
[ 1.869893] scsi4 : usb-storage 1-4:1.0
[ 1.870060] usbcore: registered new interface driver usb-storage
[ 1.870064] USB Mass Storage support registered.
[ 2.023576] Refined TSC clocksource calibration: 2133.408 MHz.
[ 2.023585] Switching to clocksource tsc
[ 2.127582] ata2: SATA link down (SStatus 0 SControl 300)
[ 2.137976] sd 0:0:0:0: [sda] 625140335 512-byte logical blocks: (320 GB/298 GiB)
[ 2.138184] sd 0:0:0:0: [sda] Write Protect is off
[ 2.138192] sd 0:0:0:0: [sda] Mode Sense: 00 3a 00 00
[ 2.138269] sd 0:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
[ 2.159585] usb 3-1: new low-speed USB device number 2 using uhci_hcd
[ 2.181823] sda: sda1 sda2 < sda5 >
[ 2.182599] sd 0:0:0:0: [sda] Attached SCSI disk
[ 2.186000] sd 0:0:0:0: Attached scsi generic sg0 type 0
[ 2.334666] usb 3-1: New USB device found, idVendor=046d, idProduct=c019
[ 2.334674] usb 3-1: New USB device strings: Mfr=1, Product=2, SerialNumber=0
[ 2.334679] usb 3-1: Product: USB Optical Mouse
[ 2.334683] usb 3-1: Manufacturer: Logitech
[ 2.357062] input: Logitech USB Optical Mouse as /devices/pci0000:00/0000:00:1d.1/usb3/3-1/3-1:1.0/input/input0
[ 2.357282] generic-usb 0003:046D:C019.0001: input,hidraw0: USB HID v1.11 Mouse [Logitech USB Optical Mouse] on usb-0000:00:1d.1-1/input0
[ 2.357327] usbcore: registered new interface driver usbhid
[ 2.357331] usbhid: USB HID core driver
[ 2.575608] usb 4-2: new low-speed USB device number 2 using uhci_hcd
[ 2.751748] usb 4-2: New USB device found, idVendor=046d, idProduct=c315
[ 2.751755] usb 4-2: New USB device strings: Mfr=1, Product=2, SerialNumber=0
[ 2.751760] usb 4-2: Product: Logitech USB Keyboard
[ 2.751764] usb 4-2: Manufacturer: Logitech
[ 2.769184] input: Logitech Logitech USB Keyboard as /devices/pci0000:00/0000:00:1d.2/usb4/4-2/4-2:1.0/input/input1
[ 2.769357] generic-usb 0003:046D:C315.0002: input,hidraw1: USB HID v1.10 Keyboard [Logitech Logitech USB Keyboard] on usb-0000:00:1d.2-2/input0
[ 2.818747] PM: Starting manual resume from disk
[ 2.818754] PM: Hibernation image partition 8:5 present
[ 2.818757] PM: Looking for hibernation image.
[ 2.819147] PM: Image not found (code -22)
[ 2.819151] PM: Hibernation image not present or could not be loaded.
[ 2.857230] kjournald starting. Commit interval 5 seconds
[ 2.857402] EXT3-fs (sda1): mounted filesystem with ordered data mode
[ 2.868640] scsi 4:0:0:0: Direct-Access SanDisk Cruzer Slice 1.02 PQ: 0 ANSI: 2
[ 2.869781] sd 4:0:0:0: Attached scsi generic sg1 type 0
[ 2.870244] sd 4:0:0:0: [sdb] 7813120 512-byte logical blocks: (4.00 GB/3.72 GiB)
[ 2.870984] sd 4:0:0:0: [sdb] Write Protect is off
[ 2.870990] sd 4:0:0:0: [sdb] Mode Sense: 03 00 00 00
[ 2.871735] sd 4:0:0:0: [sdb] No Caching mode page present
[ 2.871775] sd 4:0:0:0: [sdb] Assuming drive cache: write through
[ 2.875111] sd 4:0:0:0: [sdb] No Caching mode page present
[ 2.875150] sd 4:0:0:0: [sdb] Assuming drive cache: write through
[ 2.876027] sdb: sdb1
[ 2.878734] sd 4:0:0:0: [sdb] No Caching mode page present
[ 2.878773] sd 4:0:0:0: [sdb] Assuming drive cache: write through
[ 2.878810] sd 4:0:0:0: [sdb] Attached SCSI removable disk
[ 4.822109] udevd[338]: starting version 175
[ 5.039219] input: Power Button as /devices/LNXSYSTM:00/LNXSYBUS:00/PNP0C0C:00/input/input2
[ 5.039236] ACPI: Power Button [PWRB]
[ 5.039425] input: Sleep Button as /devices/LNXSYSTM:00/LNXSYBUS:00/PNP0C0E:00/input/input3
[ 5.039436] ACPI: Sleep Button [SLPB]
[ 5.039617] input: Power Button as /devices/LNXSYSTM:00/LNXPWRBN:00/input/input4
[ 5.039628] ACPI: Power Button [PWRF]
[ 5.071736] input: PC Speaker as /devices/platform/pcspkr/input/input5
[ 5.144556] coretemp coretemp.0: Unable to read TjMax from CPU 0
[ 5.144568] coretemp coretemp.0: Using relative temperature scale!
[ 5.144595] coretemp coretemp.0: Unable to read TjMax from CPU 2
[ 5.144605] coretemp coretemp.0: Using relative temperature scale!
[ 5.424150] iTCO_vendor_support: vendor-support=0
[ 5.432097] iTCO_wdt: Intel TCO WatchDog Timer Driver v1.07
[ 5.432330] iTCO_wdt: Found a NM10 TCO device (Version=2, TCOBASE=0x0460)
[ 5.432678] iTCO_wdt: initialized. heartbeat=30 sec (nowayout=0)
[ 5.565552] [drm] Initialized drm 1.1.0 20060810
[ 5.672793] udevd[371]: renamed network interface eth4 to rename6
[ 5.688418] gma500 0000:00:02.0: setting latency timer to 64
[ 5.688461] gma500 0000:00:02.0: irq 45 for MSI/MSI-X
[ 5.688773] Stolen memory information
[ 5.688776] base in RAM: 0x7f800000
[ 5.688780] size: 7932K, calculated by (GTT RAM base) - (Stolen base), seems wrong
[ 5.688784] the correct size should be: 8M(dvmt mode=3)
[ 5.690848] Set up 1983 stolen pages starting at 0x7f800000, GTT offset 0K
[ 5.690975] [drm] SGX core id = 0x00000000
[ 5.690978] [drm] SGX core rev major = 0x00, minor = 0x00
[ 5.690982] [drm] SGX core rev maintenance = 0x00, designer = 0x00
[ 5.703706] [drm] Supports vblank timestamp caching Rev 1 (10.10.2010).
[ 5.703711] [drm] No driver support for vblank timestamp query.
[ 5.711449] Error: Driver 'pcspkr' is already registered, aborting...
[ 6.023278] gma500 0000:00:02.0: allocated 1680x1050 fb
[ 6.023438] fbcon: psbfb (fb0) is primary device
[ 6.601651] Console: switching to colour frame buffer device 170x48
[ 6.610779] fb0: psbfb frame buffer device
[ 6.610782] drm: registered panic notifier
[ 6.610875] [drm] Initialized gma500 1.0.0 2011-06-06 for 0000:00:02.0 on minor 0
[ 6.611103] snd_hda_intel 0000:00:1b.0: irq 46 for MSI/MSI-X
[ 6.611165] snd_hda_intel 0000:00:1b.0: setting latency timer to 64
[ 6.673765] input: HDA Digital PCBeep as /devices/pci0000:00/0000:00:1b.0/input/input6
[ 6.674743] HDMI status: Codec=1 Pin=3 Presence_Detect=0 ELD_Valid=0
[ 6.678089] input: HDA Intel HDMI/DP,pcm=3 as /devices/pci0000:00/0000:00:1b.0/sound/card0/input7
[ 6.678817] input: HDA Intel Headphone as /devices/pci0000:00/0000:00:1b.0/sound/card0/input8
[ 6.679386] shpchp: Standard Hot Plug PCI Controller Driver version: 0.4
[ 6.716941] udevd[373]: renamed network interface eth3 to rename5
[ 98.028864] Adding 3989500k swap on /dev/sda5. Priority:-1 extents:1 across:3989500k
[ 98.480674] EXT3-fs (sda1): using internal journal
[ 98.677027] loop: module loaded
[ 100.535910] via-rhine 0000:03:01.0: eth1: Reset not complete yet. Trying harder.
[ 100.541903] via-rhine 0000:03:01.0: eth1: link up, 100Mbps, full-duplex, lpa 0xFFFF
[ 100.650014] RPC: Registered named UNIX socket transport module.
[ 100.650020] RPC: Registered udp transport module.
[ 100.650024] RPC: Registered tcp transport module.
[ 100.650028] RPC: Registered tcp NFSv4.1 backchannel transport module.
[ 100.707856] FS-Cache: Loaded
[ 100.743864] FS-Cache: Netfs 'nfs' registered for caching
[ 100.759436] Installing knfsd (copyright (C) 1996 okir@monad.swb.de).
[ 110.795362] eth1: no IPv6 routers present
[ 138.964354] ------------[ cut here ]------------
[ 138.964367] WARNING: at /build/buildd-linux_3.2.41-2+deb7u2-amd64-NHQI9B/linux-3.2.41/net/sched/sch_generic.c:256 dev_watchdog+0xf2/0x151()
[ 138.964373] Hardware name:
[ 138.964377] NETDEV WATCHDOG: eth1 (via-rhine): transmit queue 0 timed out
[ 138.964380] Modules linked in: nfsd nfs nfs_acl auth_rpcgss fscache lockd sunrpc loop snd_hda_codec_realtek snd_hda_codec_hdmi shpchp snd_hda_intel snd_hda_codec gma500_gfx snd_hwdep snd_pcm drm_kms_helper snd_page_alloc drm snd_timer snd i2c_i801 iTCO_wdt iTCO_vendor_support i2c_algo_bit i2c_core soundcore coretemp processor psmouse video pcspkr evdev serio_raw button thermal_sys ext3 mbcache jbd usbhid hid sg sd_mod crc_t10dif usb_storage via_rhine mii ahci libahci libata uhci_hcd scsi_mod e1000e ehci_hcd usbcore usb_common [last unloaded: scsi_wait_scan]
[ 138.964457] Pid: 0, comm: swapper/1 Not tainted 3.2.0-4-amd64 #1 Debian 3.2.41-2+deb7u2
[ 138.964461] Call Trace:
[ 138.964465] <IRQ> [<ffffffff81046a55>] ? warn_slowpath_common+0x78/0x8c
[ 138.964480] [<ffffffff81046b01>] ? warn_slowpath_fmt+0x45/0x4a
[ 138.964487] [<ffffffff812a5c4d>] ? netif_tx_lock+0x40/0x75
[ 138.964496] [<ffffffff812a5dbd>] ? dev_watchdog+0xf2/0x151
[ 138.964503] [<ffffffff81052208>] ? run_timer_softirq+0x19a/0x261
[ 138.964509] [<ffffffff812a5ccb>] ? netif_tx_unlock+0x49/0x49
[ 138.964517] [<ffffffff81065f1d>] ? timekeeping_get_ns+0xd/0x2a
[ 138.964523] [<ffffffff8104c094>] ? __do_softirq+0xb9/0x177
[ 138.964530] [<ffffffff81354c2c>] ? call_softirq+0x1c/0x30
[ 138.964538] [<ffffffff8100f8dd>] ? do_softirq+0x3c/0x7b
[ 138.964544] [<ffffffff8104c2fc>] ? irq_exit+0x3c/0x9a
[ 138.964551] [<ffffffff810241e0>] ? smp_apic_timer_interrupt+0x74/0x82
[ 138.964557] [<ffffffff8135349e>] ? apic_timer_interrupt+0x6e/0x80
[ 138.964561] <EOI> [<ffffffff810146a3>] ? mwait_idle+0x7f/0xac
[ 138.964572] [<ffffffff81014696>] ? mwait_idle+0x72/0xac
[ 138.964578] [<ffffffff8100d24d>] ? cpu_idle+0xaf/0xf2
[ 138.964584] [<ffffffff81070c36>] ? arch_local_irq_restore+0x2/0x8
[ 138.964591] [<ffffffff8133fce4>] ? start_secondary+0x1d5/0x1db
[ 138.964596] ---[ end trace ecf9398160be82d6 ]---
[ 138.965785] via-rhine 0000:03:01.0: eth1: Transmit timed out, status ffff, PHY status ffff, resetting...
[ 138.965893] via-rhine 0000:03:01.0: eth1: Reset not complete yet. Trying harder.
[ 138.971961] via-rhine 0000:03:01.0: eth1: link up, 100Mbps, full-duplex, lpa 0xFFFF
[ 426.196436] FAT-fs (sdb1): utf8 is not a recommended IO charset for FAT filesystems, filesystem will be case sensitive!
0000-0cf7 : PCI Bus 0000:00
0000-001f : dma1
0020-0021 : pic1
0040-0043 : timer0
0050-0053 : timer1
0060-0060 : keyboard
0064-0064 : keyboard
0070-0077 : rtc0
0080-008f : dma page reg
00a0-00a1 : pic2
00c0-00df : dma2
00f0-00ff : fpu
03c0-03df : vga+
0400-047f : pnp 00:04
0400-0403 : ACPI PM1a_EVT_BLK
0404-0405 : ACPI PM1a_CNT_BLK
0408-040b : ACPI PM_TMR
0410-0415 : ACPI CPU throttle
0420-0420 : ACPI PM2_CNT_BLK
0428-042f : ACPI GPE0_BLK
0430-0433 : iTCO_wdt
0430-0433 : iTCO_wdt
0460-047f : iTCO_wdt
0460-047f : iTCO_wdt
0500-057f : pnp 00:04
0600-061f : pnp 00:04
0680-069f : pnp 00:04
06a0-06af : pnp 00:05
06b0-06ff : pnp 00:05
0cf8-0cff : PCI conf1
0d00-ffff : PCI Bus 0000:00
1000-1fff : PCI Bus 0000:02
1000-1fff : PCI Bus 0000:03
1000-10ff : 0000:03:03.0
1000-10ff : via-rhine
1100-11ff : 0000:03:02.0
1100-11ff : via-rhine
1200-12ff : 0000:03:01.0
1200-12ff : via-rhine
1300-13ff : 0000:03:00.0
1300-13ff : via-rhine
2000-2fff : PCI Bus 0000:01
2000-201f : 0000:01:00.0
3000-301f : 0000:00:1f.3
3000-301f : i801_smbus
3020-302f : 0000:00:1f.2
3020-302f : ahci
3040-305f : 0000:00:1d.3
3040-305f : uhci_hcd
3060-307f : 0000:00:1d.2
3060-307f : uhci_hcd
3080-309f : 0000:00:1d.1
3080-309f : uhci_hcd
30a0-30bf : 0000:00:1d.0
30a0-30bf : uhci_hcd
30c0-30c7 : 0000:00:1f.2
30c0-30c7 : ahci
30c8-30cf : 0000:00:1f.2
30c8-30cf : ahci
30d0-30d7 : 0000:00:02.0
30d8-30db : 0000:00:1f.2
30d8-30db : ahci
30dc-30df : 0000:00:1f.2
30dc-30df : ahci
ffff-ffff : pnp 00:04
ffff-ffff : pnp 00:04
ffff-ffff : pnp 00:04
0000-001f : dma1
0020-0021 : pic1
0040-0043 : timer0
0050-0053 : timer1
0060-0060 : keyboard
0064-0064 : keyboard
0070-0077 : rtc0
0080-008f : dma page reg
00a0-00a1 : pic2
00c0-00df : dma2
00f0-00ff : fpu
03c0-03df : vga+
0400-047f : pnp 00:05
0400-0403 : ACPI PM1a_EVT_BLK
0404-0405 : ACPI PM1a_CNT_BLK
0408-040b : ACPI PM_TMR
0410-0415 : ACPI CPU throttle
0420-0420 : ACPI PM2_CNT_BLK
0428-042f : ACPI GPE0_BLK
0500-057f : pnp 00:05
0600-061f : pnp 00:05
0680-069f : pnp 00:05
06a0-06af : pnp 00:06
06b0-06ff : pnp 00:06
0cf8-0cff : PCI conf1
1000-1fff : PCI Bus 0000:02
1000-1fff : PCI Bus 0000:03
1000-10ff : 0000:03:03.0
1000-10ff : via-rhine
1100-11ff : 0000:03:02.0
1200-12ff : 0000:03:01.0
1300-13ff : 0000:03:00.0
2000-2fff : PCI Bus 0000:01
2000-201f : 0000:01:00.0
3000-301f : 0000:00:1f.3
3000-301f : i801_smbus
3020-302f : 0000:00:1f.2
3020-302f : ahci
3040-305f : 0000:00:1d.3
3040-305f : uhci_hcd
3060-307f : 0000:00:1d.2
3060-307f : uhci_hcd
3080-309f : 0000:00:1d.1
3080-309f : uhci_hcd
30a0-30bf : 0000:00:1d.0
30a0-30bf : uhci_hcd
30c0-30c7 : 0000:00:1f.2
30c0-30c7 : ahci
30c8-30cf : 0000:00:1f.2
30c8-30cf : ahci
30d0-30d7 : 0000:00:02.0
30d8-30db : 0000:00:1f.2
30d8-30db : ahci
30dc-30df : 0000:00:1f.2
30dc-30df : ahci
ffff-ffff : pnp 00:05
ffff-ffff : pnp 00:05
ffff-ffff : pnp 00:05
[ 0.000000] Initializing cgroup subsys cpuset
[ 0.000000] Initializing cgroup subsys cpu
[ 0.000000] Linux version 3.8-2-amd64 (debian-kernel@lists.debian.org) (gcc version 4.7.2 (Debian 4.7.2-5) ) #1 SMP Debian 3.8.13-1
[ 0.000000] Command line: BOOT_IMAGE=/boot/vmlinuz-3.8-2-amd64 root=UUID=54290ac6-2db5-424b-8cdb-e54f7e644b70 ro quiet
[ 0.000000] Disabled fast string operations
[ 0.000000] e820: BIOS-provided physical RAM map:
[ 0.000000] BIOS-e820: [mem 0x0000000000000000-0x000000000008efff] usable
[ 0.000000] BIOS-e820: [mem 0x000000000008f000-0x000000000008ffff] reserved
[ 0.000000] BIOS-e820: [mem 0x0000000000090000-0x000000000009e7ff] usable
[ 0.000000] BIOS-e820: [mem 0x000000000009e800-0x000000000009ffff] reserved
[ 0.000000] BIOS-e820: [mem 0x00000000000e0000-0x00000000000fffff] reserved
[ 0.000000] BIOS-e820: [mem 0x0000000000100000-0x000000007ee97fff] usable
[ 0.000000] BIOS-e820: [mem 0x000000007ee98000-0x000000007eebefff] reserved
[ 0.000000] BIOS-e820: [mem 0x000000007eebf000-0x000000007eefefff] usable
[ 0.000000] BIOS-e820: [mem 0x000000007eeff000-0x000000007efbefff] ACPI NVS
[ 0.000000] BIOS-e820: [mem 0x000000007efbf000-0x000000007eff1fff] usable
[ 0.000000] BIOS-e820: [mem 0x000000007eff2000-0x000000007effefff] ACPI data
[ 0.000000] BIOS-e820: [mem 0x000000007efff000-0x000000007effffff] usable
[ 0.000000] BIOS-e820: [mem 0x000000007f000000-0x000000007fffffff] reserved
[ 0.000000] BIOS-e820: [mem 0x00000000e0000000-0x00000000e3ffffff] reserved
[ 0.000000] BIOS-e820: [mem 0x00000000ffe00000-0x00000000ffffffff] reserved
[ 0.000000] NX (Execute Disable) protection: active
[ 0.000000] SMBIOS 2.7 present.
[ 0.000000] DMI: /D2700DC , BIOS MUCDT10N.86A.0075.2013.0427.1548 04/27/2013
[ 0.000000] e820: update [mem 0x00000000-0x0000ffff] usable ==> reserved
[ 0.000000] e820: remove [mem 0x000a0000-0x000fffff] usable
[ 0.000000] No AGP bridge found
[ 0.000000] e820: last_pfn = 0x7f000 max_arch_pfn = 0x400000000
[ 0.000000] MTRR default type: uncachable
[ 0.000000] MTRR fixed ranges enabled:
[ 0.000000] 00000-9FFFF write-back
[ 0.000000] A0000-BFFFF uncachable
[ 0.000000] C0000-DFFFF write-protect
[ 0.000000] E0000-FFFFF uncachable
[ 0.000000] MTRR variable ranges enabled:
[ 0.000000] 0 base 000000000 mask F80000000 write-back
[ 0.000000] 1 base 07F000000 mask FFF000000 uncachable
[ 0.000000] 2 base 0FFE00000 mask FFFE00000 write-protect
[ 0.000000] 3 disabled
[ 0.000000] 4 disabled
[ 0.000000] 5 disabled
[ 0.000000] 6 disabled
[ 0.000000] x86 PAT enabled: cpu 0, old 0x7040600070406, new 0x7010600070106
[ 0.000000] found SMP MP-table at [mem 0x000fbe40-0x000fbe4f] mapped at [ffff8800000fbe40]
[ 0.000000] initial memory mapped: [mem 0x00000000-0x1fffffff]
[ 0.000000] Base memory trampoline at [ffff880000098000] 98000 size 24576
[ 0.000000] init_memory_mapping: [mem 0x00000000-0x7effffff]
[ 0.000000] [mem 0x00000000-0x7effffff] page 2M
[ 0.000000] kernel direct mapping tables up to 0x7effffff @ [mem 0x1fffd000-0x1fffffff]
[ 0.000000] RAMDISK: [mem 0x36a32000-0x37510fff]
[ 0.000000] ACPI: RSDP 00000000000f2390 00024 (v02 INTEL )
[ 0.000000] ACPI: XSDT 000000007effe120 0004C (v01 INTEL TIANO 0000004B 01000013)
[ 0.000000] ACPI: FACP 000000007eff6000 000F4 (v03 INTEL TIANO 0000004B MSFT 0100000D)
[ 0.000000] ACPI: DSDT 000000007eff8000 05B38 (v02 INTEL TIANO 0000004B MSFT 0100000D)
[ 0.000000] ACPI: FACS 000000007ef85000 00040
[ 0.000000] ACPI: SSDT 000000007eff7000 0043E (v01 INTEL TIANO 0000004B MSFT 0100000D)
[ 0.000000] ACPI: APIC 000000007eff5000 00084 (v02 INTEL TIANO 0000004B MSFT 0100000D)
[ 0.000000] ACPI: MCFG 000000007eff4000 0003C (v01 INTEL TIANO 0000004B MSFT 0100000D)
[ 0.000000] ACPI: HPET 000000007eff3000 00038 (v01 INTEL TIANO 0000004B MSFT 0100000D)
[ 0.000000] ACPI: Local APIC address 0xfee00000
[ 0.000000] No NUMA configuration found
[ 0.000000] Faking a node at [mem 0x0000000000000000-0x000000007effffff]
[ 0.000000] Initmem setup node 0 [mem 0x00000000-0x7effffff]
[ 0.000000] NODE_DATA [mem 0x7efee000-0x7eff1fff]
[ 0.000000] [ffffea0000000000-ffffea0001bfffff] PMD -> [ffff88007c600000-ffff88007e1fffff] on node 0
[ 0.000000] Zone ranges:
[ 0.000000] DMA [mem 0x00010000-0x00ffffff]
[ 0.000000] DMA32 [mem 0x01000000-0xffffffff]
[ 0.000000] Normal empty
[ 0.000000] Movable zone start for each node
[ 0.000000] Early memory node ranges
[ 0.000000] node 0: [mem 0x00010000-0x0008efff]
[ 0.000000] node 0: [mem 0x00090000-0x0009dfff]
[ 0.000000] node 0: [mem 0x00100000-0x7ee97fff]
[ 0.000000] node 0: [mem 0x7eebf000-0x7eefefff]
[ 0.000000] node 0: [mem 0x7efbf000-0x7eff1fff]
[ 0.000000] node 0: [mem 0x7efff000-0x7effffff]
[ 0.000000] On node 0 totalpages: 519833
[ 0.000000] DMA zone: 56 pages used for memmap
[ 0.000000] DMA zone: 6 pages reserved
[ 0.000000] DMA zone: 3919 pages, LIFO batch:0
[ 0.000000] DMA32 zone: 7056 pages used for memmap
[ 0.000000] DMA32 zone: 508796 pages, LIFO batch:31
[ 0.000000] ACPI: PM-Timer IO Port: 0x408
[ 0.000000] ACPI: Local APIC address 0xfee00000
[ 0.000000] ACPI: LAPIC (acpi_id[0x01] lapic_id[0x00] enabled)
[ 0.000000] ACPI: LAPIC (acpi_id[0x02] lapic_id[0x01] enabled)
[ 0.000000] ACPI: LAPIC (acpi_id[0x03] lapic_id[0x02] enabled)
[ 0.000000] ACPI: LAPIC (acpi_id[0x04] lapic_id[0x03] enabled)
[ 0.000000] ACPI: LAPIC_NMI (acpi_id[0x01] high level lint[0x1])
[ 0.000000] ACPI: LAPIC_NMI (acpi_id[0x02] high level lint[0x1])
[ 0.000000] ACPI: LAPIC_NMI (acpi_id[0x03] high level lint[0x1])
[ 0.000000] ACPI: LAPIC_NMI (acpi_id[0x04] high level lint[0x1])
[ 0.000000] ACPI: IOAPIC (id[0x08] address[0xfec00000] gsi_base[0])
[ 0.000000] IOAPIC[0]: apic_id 8, version 32, address 0xfec00000, GSI 0-23
[ 0.000000] ACPI: INT_SRC_OVR (bus 0 bus_irq 0 global_irq 2 dfl dfl)
[ 0.000000] ACPI: INT_SRC_OVR (bus 0 bus_irq 9 global_irq 9 high level)
[ 0.000000] ACPI: IRQ0 used by override.
[ 0.000000] ACPI: IRQ2 used by override.
[ 0.000000] ACPI: IRQ9 used by override.
[ 0.000000] Using ACPI (MADT) for SMP configuration information
[ 0.000000] ACPI: HPET id: 0x8086a201 base: 0xfed00000
[ 0.000000] smpboot: Allowing 4 CPUs, 0 hotplug CPUs
[ 0.000000] nr_irqs_gsi: 40
[ 0.000000] PM: Registered nosave memory: 000000000008f000 - 0000000000090000
[ 0.000000] PM: Registered nosave memory: 000000000009e000 - 000000000009f000
[ 0.000000] PM: Registered nosave memory: 000000000009f000 - 00000000000a0000
[ 0.000000] PM: Registered nosave memory: 00000000000a0000 - 00000000000e0000
[ 0.000000] PM: Registered nosave memory: 00000000000e0000 - 0000000000100000
[ 0.000000] PM: Registered nosave memory: 000000007ee98000 - 000000007eebf000
[ 0.000000] PM: Registered nosave memory: 000000007eeff000 - 000000007efbf000
[ 0.000000] PM: Registered nosave memory: 000000007eff2000 - 000000007efff000
[ 0.000000] e820: [mem 0x80000000-0xdfffffff] available for PCI devices
[ 0.000000] Booting paravirtualized kernel on bare hardware
[ 0.000000] setup_percpu: NR_CPUS:512 nr_cpumask_bits:512 nr_cpu_ids:4 nr_node_ids:1
[ 0.000000] PERCPU: Embedded 28 pages/cpu @ffff88007ec00000 s84096 r8192 d22400 u524288
[ 0.000000] pcpu-alloc: s84096 r8192 d22400 u524288 alloc=1*2097152
[ 0.000000] pcpu-alloc: [0] 0 1 2 3
[ 0.000000] Built 1 zonelists in Node order, mobility grouping on. Total pages: 512715
[ 0.000000] Policy zone: DMA32
[ 0.000000] Kernel command line: BOOT_IMAGE=/boot/vmlinuz-3.8-2-amd64 root=UUID=54290ac6-2db5-424b-8cdb-e54f7e644b70 ro quiet
[ 0.000000] PID hash table entries: 4096 (order: 3, 32768 bytes)
[ 0.000000] __ex_table already sorted, skipping sort
[ 0.000000] Checking aperture...
[ 0.000000] No AGP bridge found
[ 0.000000] Calgary: detecting Calgary via BIOS EBDA area
[ 0.000000] Calgary: Unable to locate Rio Grande table in EBDA - bailing!
[ 0.000000] Memory: 2030524k/2080768k available (3633k kernel code, 1436k absent, 48808k reserved, 3104k data, 616k init)
[ 0.000000] Hierarchical RCU implementation.
[ 0.000000] RCU dyntick-idle grace-period acceleration is enabled.
[ 0.000000] RCU restricting CPUs from NR_CPUS=512 to nr_cpu_ids=4.
[ 0.000000] NR_IRQS:33024 nr_irqs:712 16
[ 0.000000] Extended CMOS year: 2000
[ 0.000000] Console: colour VGA+ 80x25
[ 0.000000] console [tty0] enabled
[ 0.000000] hpet clockevent registered
[ 0.000000] tsc: Fast TSC calibration failed
[ 0.008000] tsc: PIT calibration matches HPET. 1 loops
[ 0.008000] tsc: Detected 2133.413 MHz processor
[ 0.000006] Calibrating delay loop (skipped), value calculated using timer frequency.. 4266.82 BogoMIPS (lpj=8533652)
[ 0.000013] pid_max: default: 32768 minimum: 301
[ 0.000107] Security Framework initialized
[ 0.000114] AppArmor: AppArmor disabled by boot time parameter
[ 0.000484] Dentry cache hash table entries: 262144 (order: 9, 2097152 bytes)
[ 0.002080] Inode-cache hash table entries: 131072 (order: 8, 1048576 bytes)
[ 0.002828] Mount-cache hash table entries: 256
[ 0.003238] Initializing cgroup subsys cpuacct
[ 0.003245] Initializing cgroup subsys memory
[ 0.003277] Initializing cgroup subsys devices
[ 0.003282] Initializing cgroup subsys freezer
[ 0.003286] Initializing cgroup subsys net_cls
[ 0.003290] Initializing cgroup subsys blkio
[ 0.003294] Initializing cgroup subsys perf_event
[ 0.003347] Disabled fast string operations
[ 0.003355] CPU: Physical Processor ID: 0
[ 0.003358] CPU: Processor Core ID: 0
[ 0.003362] mce: CPU supports 5 MCE banks
[ 0.003376] CPU0: Thermal monitoring enabled (TM1)
[ 0.003383] process: using mwait in idle threads
[ 0.003393] Last level iTLB entries: 4KB 32, 2MB 0, 4MB 0
[ 0.003393] Last level dTLB entries: 4KB 64, 2MB 0, 4MB 8
[ 0.003393] tlb_flushall_shift: 6
[ 0.003513] Freeing SMP alternatives: 12k freed
[ 0.004066] ACPI: Core revision 20121018
[ 0.012611] ..TIMER: vector=0x30 apic1=0 pin1=2 apic2=-1 pin2=-1
[ 0.055430] smpboot: CPU0: Intel(R) Atom(TM) CPU D2700 @ 2.13GHz (fam: 06, model: 36, stepping: 01)
[ 0.159262] Performance Events: PEBS fmt0+, 8-deep LBR, Atom events, Intel PMU driver.
[ 0.159276] ... version: 3
[ 0.159279] ... bit width: 40
[ 0.159282] ... generic registers: 2
[ 0.159285] ... value mask: 000000ffffffffff
[ 0.159288] ... max period: 000000007fffffff
[ 0.159291] ... fixed-purpose events: 3
[ 0.159294] ... event mask: 0000000700000003
[ 0.171010] Disabled fast string operations
[ 0.173448] NMI watchdog: enabled on all CPUs, permanently consumes one hw-PMU counter.
[ 0.184716] Disabled fast string operations
[ 0.160084] smpboot: Booting Node 0, Processors #1 #2 #3 OK
[ 0.198055] Disabled fast string operations
[ 0.200168] Brought up 4 CPUs
[ 0.200176] smpboot: Total of 4 processors activated (17067.30 BogoMIPS)
[ 0.201333] devtmpfs: initialized
[ 0.206153] PM: Registering ACPI NVS region [mem 0x7eeff000-0x7efbefff] (786432 bytes)
[ 0.206503] regulator-dummy: no parameters
[ 0.206662] NET: Registered protocol family 16
[ 0.206985] ACPI FADT declares the system doesn't support PCIe ASPM, so disable it
[ 0.206991] ACPI: bus type pci registered
[ 0.207158] PCI: MMCONFIG for domain 0000 [bus 00-3f] at [mem 0xe0000000-0xe3ffffff] (base 0xe0000000)
[ 0.207184] PCI: MMCONFIG at [mem 0xe0000000-0xe3ffffff] reserved in E820
[ 0.214765] PCI: Using configuration type 1 for base access
[ 0.216828] bio: create slab <bio-0> at 0
[ 0.217060] ACPI: Added _OSI(Module Device)
[ 0.217065] ACPI: Added _OSI(Processor Device)
[ 0.217071] ACPI: Added _OSI(3.0 _SCP Extensions)
[ 0.217075] ACPI: Added _OSI(Processor Aggregator Device)
[ 0.219092] ACPI: EC: Look up EC in DSDT
[ 0.221280] ACPI: Executed 1 blocks of module-level executable AML code
[ 0.226081] [Firmware Bug]: ACPI: BIOS _OSI(Linux) query ignored
[ 0.226915] ACPI: Interpreter enabled
[ 0.226923] ACPI: (supports S0 S3 S4 S5)
[ 0.226974] ACPI: Using IOAPIC for interrupt routing
[ 0.239607] ACPI: No dock devices found.
[ 0.239619] PCI: Using host bridge windows from ACPI; if necessary, use "pci=nocrs" and report a bug
[ 0.240062] ACPI: PCI Root Bridge [PCI0] (domain 0000 [bus 00-ff])
[ 0.240069] ACPI: PCI Interrupt Routing Table [\_SB_.PCI0._PRT]
[ 0.240336] \_SB_.PCI0:_OSC invalid UUID
[ 0.240340] _OSC request data:1 8 0
[ 0.241028] pci_root PNP0A08:00: [Firmware Info]: MMCONFIG for domain 0000 [bus 00-3f] only partially covers this bridge
[ 0.241115] PCI host bridge to bus 0000:00
[ 0.241123] pci_bus 0000:00: root bus resource [bus 00-ff]
[ 0.241129] pci_bus 0000:00: root bus resource [io 0x0000-0x0cf7]
[ 0.241135] pci_bus 0000:00: root bus resource [io 0x0d00-0xffff]
[ 0.241140] pci_bus 0000:00: root bus resource [mem 0x000a0000-0x000bffff]
[ 0.241146] pci_bus 0000:00: root bus resource [mem 0x000c0000-0x000dffff]
[ 0.241151] pci_bus 0000:00: root bus resource [mem 0x000e0000-0x000effff]
[ 0.241157] pci_bus 0000:00: root bus resource [mem 0x000f0000-0x000fffff]
[ 0.241162] pci_bus 0000:00: root bus resource [mem 0x7f800000-0x7fffffff]
[ 0.241168] pci_bus 0000:00: root bus resource [mem 0x80000000-0xfebfffff]
[ 0.241173] pci_bus 0000:00: root bus resource [mem 0xfed40000-0xfed44fff]
[ 0.241192] pci 0000:00:00.0: [8086:0bf3] type 00 class 0x060000
[ 0.241254] pci 0000:00:02.0: [8086:0be2] type 00 class 0x030000
[ 0.241270] pci 0000:00:02.0: reg 10: [mem 0x80200000-0x802fffff]
[ 0.241279] pci 0000:00:02.0: reg 14: [io 0x30d0-0x30d7]
[ 0.241381] pci 0000:00:1b.0: [8086:27d8] type 00 class 0x040300
[ 0.241403] pci 0000:00:1b.0: reg 10: [mem 0x80400000-0x80403fff 64bit]
[ 0.241495] pci 0000:00:1b.0: PME# supported from D0 D3hot D3cold
[ 0.241536] pci 0000:00:1c.0: [8086:27d0] type 01 class 0x060400
[ 0.241624] pci 0000:00:1c.0: PME# supported from D0 D3hot D3cold
[ 0.241670] pci 0000:00:1d.0: [8086:27c8] type 00 class 0x0c0300
[ 0.241737] pci 0000:00:1d.0: reg 20: [io 0x30a0-0x30bf]
[ 0.241795] pci 0000:00:1d.1: [8086:27c9] type 00 class 0x0c0300
[ 0.241860] pci 0000:00:1d.1: reg 20: [io 0x3080-0x309f]
[ 0.241918] pci 0000:00:1d.2: [8086:27ca] type 00 class 0x0c0300
[ 0.241981] pci 0000:00:1d.2: reg 20: [io 0x3060-0x307f]
[ 0.242041] pci 0000:00:1d.3: [8086:27cb] type 00 class 0x0c0300
[ 0.242106] pci 0000:00:1d.3: reg 20: [io 0x3040-0x305f]
[ 0.242174] pci 0000:00:1d.7: [8086:27cc] type 00 class 0x0c0320
[ 0.242201] pci 0000:00:1d.7: reg 10: [mem 0x80304400-0x803047ff]
[ 0.242307] pci 0000:00:1d.7: PME# supported from D0 D3hot D3cold
[ 0.242340] pci 0000:00:1e.0: [8086:2448] type 01 class 0x060401
[ 0.242427] pci 0000:00:1f.0: [8086:27bc] type 00 class 0x060100
[ 0.242525] pci 0000:00:1f.0: [Firmware Bug]: TigerPoint LPC.BM_STS cleared
[ 0.242590] pci 0000:00:1f.2: [8086:27c1] type 00 class 0x010601
[ 0.242612] pci 0000:00:1f.2: reg 10: [io 0x30c8-0x30cf]
[ 0.242624] pci 0000:00:1f.2: reg 14: [io 0x30dc-0x30df]
[ 0.242638] pci 0000:00:1f.2: reg 18: [io 0x30c0-0x30c7]
[ 0.242650] pci 0000:00:1f.2: reg 1c: [io 0x30d8-0x30db]
[ 0.242662] pci 0000:00:1f.2: reg 20: [io 0x3020-0x302f]
[ 0.242675] pci 0000:00:1f.2: reg 24: [mem 0x80304000-0x803043ff]
[ 0.242724] pci 0000:00:1f.2: PME# supported from D3hot
[ 0.242754] pci 0000:00:1f.3: [8086:27da] type 00 class 0x0c0500
[ 0.242819] pci 0000:00:1f.3: reg 20: [io 0x3000-0x301f]
[ 0.243017] pci 0000:01:00.0: [8086:10d3] type 00 class 0x020000
[ 0.243051] pci 0000:01:00.0: reg 10: [mem 0x80120000-0x8013ffff]
[ 0.243077] pci 0000:01:00.0: reg 14: [mem 0x80100000-0x8011ffff]
[ 0.243115] pci 0000:01:00.0: reg 18: [io 0x2000-0x201f]
[ 0.243142] pci 0000:01:00.0: reg 1c: [mem 0x80140000-0x80143fff]
[ 0.243330] pci 0000:01:00.0: PME# supported from D0 D3hot D3cold
[ 0.243419] pci 0000:00:1c.0: PCI bridge to [bus 01]
[ 0.243427] pci 0000:00:1c.0: bridge window [io 0x2000-0x2fff]
[ 0.243435] pci 0000:00:1c.0: bridge window [mem 0x80100000-0x801fffff]
[ 0.243494] pci 0000:02:00.0: [104c:ac23] type 01 class 0x060400
[ 0.243636] pci 0000:00:1e.0: PCI bridge to [bus 02-03] (subtractive decode)
[ 0.243643] pci 0000:00:1e.0: bridge window [io 0x1000-0x1fff]
[ 0.243650] pci 0000:00:1e.0: bridge window [mem 0x80000000-0x800fffff]
[ 0.243661] pci 0000:00:1e.0: bridge window [io 0x0000-0x0cf7] (subtractive decode)
[ 0.243666] pci 0000:00:1e.0: bridge window [io 0x0d00-0xffff] (subtractive decode)
[ 0.243672] pci 0000:00:1e.0: bridge window [mem 0x000a0000-0x000bffff] (subtractive decode)
[ 0.243678] pci 0000:00:1e.0: bridge window [mem 0x000c0000-0x000dffff] (subtractive decode)
[ 0.243683] pci 0000:00:1e.0: bridge window [mem 0x000e0000-0x000effff] (subtractive decode)
[ 0.243689] pci 0000:00:1e.0: bridge window [mem 0x000f0000-0x000fffff] (subtractive decode)
[ 0.243694] pci 0000:00:1e.0: bridge window [mem 0x7f800000-0x7fffffff] (subtractive decode)
[ 0.243700] pci 0000:00:1e.0: bridge window [mem 0x80000000-0xfebfffff] (subtractive decode)
[ 0.243706] pci 0000:00:1e.0: bridge window [mem 0xfed40000-0xfed44fff] (subtractive decode)
[ 0.243766] pci 0000:03:00.0: [1106:3053] type 00 class 0x020000
[ 0.243797] pci 0000:03:00.0: reg 10: [io 0x1300-0x13ff]
[ 0.243817] pci 0000:03:00.0: reg 14: [mem 0x80000300-0x800003ff]
[ 0.243930] pci 0000:03:00.0: supports D1 D2
[ 0.243935] pci 0000:03:00.0: PME# supported from D0 D1 D2 D3hot D3cold
[ 0.243980] pci 0000:03:01.0: [1106:3053] type 00 class 0x020000
[ 0.244011] pci 0000:03:01.0: reg 10: [io 0x1200-0x12ff]
[ 0.244031] pci 0000:03:01.0: reg 14: [mem 0x80000200-0x800002ff]
[ 0.244149] pci 0000:03:01.0: supports D1 D2
[ 0.244153] pci 0000:03:01.0: PME# supported from D0 D1 D2 D3hot D3cold
[ 0.244193] pci 0000:03:02.0: [1106:3053] type 00 class 0x020000
[ 0.244225] pci 0000:03:02.0: reg 10: [io 0x1100-0x11ff]
[ 0.244244] pci 0000:03:02.0: reg 14: [mem 0x80000100-0x800001ff]
[ 0.244359] pci 0000:03:02.0: supports D1 D2
[ 0.244364] pci 0000:03:02.0: PME# supported from D0 D1 D2 D3hot D3cold
[ 0.244404] pci 0000:03:03.0: [1106:3053] type 00 class 0x020000
[ 0.244435] pci 0000:03:03.0: reg 10: [io 0x1000-0x10ff]
[ 0.244455] pci 0000:03:03.0: reg 14: [mem 0x80000000-0x800000ff]
[ 0.244573] pci 0000:03:03.0: supports D1 D2
[ 0.244578] pci 0000:03:03.0: PME# supported from D0 D1 D2 D3hot D3cold
[ 0.244651] pci 0000:02:00.0: PCI bridge to [bus 03]
[ 0.244662] pci 0000:02:00.0: bridge window [io 0x1000-0x1fff]
[ 0.244671] pci 0000:02:00.0: bridge window [mem 0x80000000-0x800fffff]
[ 0.244732] ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.P0P1._PRT]
[ 0.245113] ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.RP01._PRT]
[ 0.245390] \_SB_.PCI0:_OSC invalid UUID
[ 0.245394] _OSC request data:1 1f 0
[ 0.245402] pci0000:00: ACPI _OSC support notification failed, disabling PCIe ASPM
[ 0.245406] pci0000:00: Unable to request _OSC control (_OSC support mask: 0x08)
[ 0.247608] ACPI: PCI Interrupt Link [LNKA] (IRQs 1 3 4 5 6 7 10 12 14 15) *11
[ 0.247748] ACPI: PCI Interrupt Link [LNKB] (IRQs 1 3 4 5 6 7 11 12 14 15) *0, disabled.
[ 0.247884] ACPI: PCI Interrupt Link [LNKC] (IRQs 1 3 4 5 6 7 10 12 14 15) *9
[ 0.248019] ACPI: PCI Interrupt Link [LNKD] (IRQs 1 3 4 5 6 7 *11 12 14 15)
[ 0.248152] ACPI: PCI Interrupt Link [LNKE] (IRQs 1 3 4 5 6 7 *10 12 14 15)
[ 0.248290] ACPI: PCI Interrupt Link [LNKF] (IRQs 1 3 4 5 6 7 *11 12 14 15)
[ 0.248423] ACPI: PCI Interrupt Link [LNKG] (IRQs 1 3 4 5 6 7 10 12 14 15) *9
[ 0.248558] ACPI: PCI Interrupt Link [LNKH] (IRQs 1 3 4 5 6 7 11 12 14 15) *10
[ 0.248827] vgaarb: device added: PCI:0000:00:02.0,decodes=io+mem,owns=io+mem,locks=none
[ 0.248843] vgaarb: loaded
[ 0.248847] vgaarb: bridge control possible 0000:00:02.0
[ 0.248990] PCI: Using ACPI for IRQ routing
[ 0.250715] PCI: pci_cache_line_size set to 64 bytes
[ 0.250873] e820: reserve RAM buffer [mem 0x0008f000-0x0008ffff]
[ 0.250878] e820: reserve RAM buffer [mem 0x0009e800-0x0009ffff]
[ 0.250883] e820: reserve RAM buffer [mem 0x7ee98000-0x7fffffff]
[ 0.250887] e820: reserve RAM buffer [mem 0x7eeff000-0x7fffffff]
[ 0.250892] e820: reserve RAM buffer [mem 0x7eff2000-0x7fffffff]
[ 0.250896] e820: reserve RAM buffer [mem 0x7f000000-0x7fffffff]
[ 0.251170] hpet0: at MMIO 0xfed00000, IRQs 2, 8, 0
[ 0.251180] hpet0: 3 comparators, 64-bit 14.318180 MHz counter
[ 0.253196] Switching to clocksource hpet
[ 0.258092] pnp: PnP ACPI init
[ 0.258134] ACPI: bus type pnp registered
[ 0.258211] pnp 00:00: [dma 4]
[ 0.258272] pnp 00:00: Plug and Play ACPI device, IDs PNP0200 (active)
[ 0.258345] pnp 00:01: Plug and Play ACPI device, IDs INT0800 (active)
[ 0.258660] system 00:02: [mem 0xfed00000-0xfed003ff] has been reserved
[ 0.258670] system 00:02: Plug and Play ACPI device, IDs PNP0103 PNP0c01 (active)
[ 0.258761] pnp 00:03: Plug and Play ACPI device, IDs PNP0c04 (active)
[ 0.258888] system 00:04: [io 0x0680-0x069f] has been reserved
[ 0.258895] system 00:04: [io 0xffff] has been reserved
[ 0.258902] system 00:04: [io 0xffff] has been reserved
[ 0.258908] system 00:04: [io 0xffff] has been reserved
[ 0.258914] system 00:04: [io 0x0400-0x047f] has been reserved
[ 0.258920] system 00:04: [io 0x0500-0x057f] has been reserved
[ 0.258926] system 00:04: [io 0x0600-0x061f] has been reserved
[ 0.258933] system 00:04: Plug and Play ACPI device, IDs PNP0c02 (active)
[ 0.259069] system 00:05: [io 0x06a0-0x06af] has been reserved
[ 0.259075] system 00:05: [io 0x06b0-0x06ff] has been reserved
[ 0.259082] system 00:05: Plug and Play ACPI device, IDs PNP0c02 (active)
[ 0.259172] pnp 00:06: Plug and Play ACPI device, IDs PNP0b00 (active)
[ 0.260022] system 00:07: [mem 0xfed1c000-0xfed1ffff] has been reserved
[ 0.260030] system 00:07: [mem 0x00000000-0x00003fff] could not be reserved
[ 0.260037] system 00:07: [mem 0x00000000-0x00000fff] could not be reserved
[ 0.260043] system 00:07: [mem 0x00000000-0x00000fff] could not be reserved
[ 0.260049] system 00:07: [mem 0xfed45000-0xfed8ffff] has been reserved
[ 0.260057] system 00:07: Plug and Play ACPI device, IDs PNP0c02 (active)
[ 0.260389] pnp: PnP ACPI: found 8 devices
[ 0.260393] ACPI: ACPI bus type pnp unregistered
[ 0.270420] pci 0000:00:1c.0: bridge window [mem 0x00100000-0x000fffff 64bit pref] to [bus 01] add_size 200000
[ 0.270457] pci 0000:00:1c.0: res[15]=[mem 0x00100000-0x000fffff 64bit pref] get_res_add_size add_size 200000
[ 0.270471] pci 0000:00:1c.0: BAR 15: assigned [mem 0x80500000-0x806fffff 64bit pref]
[ 0.270478] pci 0000:00:1c.0: PCI bridge to [bus 01]
[ 0.270485] pci 0000:00:1c.0: bridge window [io 0x2000-0x2fff]
[ 0.270494] pci 0000:00:1c.0: bridge window [mem 0x80100000-0x801fffff]
[ 0.270502] pci 0000:00:1c.0: bridge window [mem 0x80500000-0x806fffff 64bit pref]
[ 0.270515] pci 0000:02:00.0: PCI bridge to [bus 03]
[ 0.270521] pci 0000:02:00.0: bridge window [io 0x1000-0x1fff]
[ 0.270530] pci 0000:02:00.0: bridge window [mem 0x80000000-0x800fffff]
[ 0.270546] pci 0000:00:1e.0: PCI bridge to [bus 02-03]
[ 0.270552] pci 0000:00:1e.0: bridge window [io 0x1000-0x1fff]
[ 0.270560] pci 0000:00:1e.0: bridge window [mem 0x80000000-0x800fffff]
[ 0.270610] pci 0000:00:1e.0: setting latency timer to 64
[ 0.270624] pci_bus 0000:00: resource 4 [io 0x0000-0x0cf7]
[ 0.270629] pci_bus 0000:00: resource 5 [io 0x0d00-0xffff]
[ 0.270634] pci_bus 0000:00: resource 6 [mem 0x000a0000-0x000bffff]
[ 0.270639] pci_bus 0000:00: resource 7 [mem 0x000c0000-0x000dffff]
[ 0.270644] pci_bus 0000:00: resource 8 [mem 0x000e0000-0x000effff]
[ 0.270649] pci_bus 0000:00: resource 9 [mem 0x000f0000-0x000fffff]
[ 0.270655] pci_bus 0000:00: resource 10 [mem 0x7f800000-0x7fffffff]
[ 0.270660] pci_bus 0000:00: resource 11 [mem 0x80000000-0xfebfffff]
[ 0.270665] pci_bus 0000:00: resource 12 [mem 0xfed40000-0xfed44fff]
[ 0.270671] pci_bus 0000:01: resource 0 [io 0x2000-0x2fff]
[ 0.270676] pci_bus 0000:01: resource 1 [mem 0x80100000-0x801fffff]
[ 0.270681] pci_bus 0000:01: resource 2 [mem 0x80500000-0x806fffff 64bit pref]
[ 0.270687] pci_bus 0000:02: resource 0 [io 0x1000-0x1fff]
[ 0.270692] pci_bus 0000:02: resource 1 [mem 0x80000000-0x800fffff]
[ 0.270697] pci_bus 0000:02: resource 4 [io 0x0000-0x0cf7]
[ 0.270702] pci_bus 0000:02: resource 5 [io 0x0d00-0xffff]
[ 0.270707] pci_bus 0000:02: resource 6 [mem 0x000a0000-0x000bffff]
[ 0.270712] pci_bus 0000:02: resource 7 [mem 0x000c0000-0x000dffff]
[ 0.270717] pci_bus 0000:02: resource 8 [mem 0x000e0000-0x000effff]
[ 0.270722] pci_bus 0000:02: resource 9 [mem 0x000f0000-0x000fffff]
[ 0.270728] pci_bus 0000:02: resource 10 [mem 0x7f800000-0x7fffffff]
[ 0.270733] pci_bus 0000:02: resource 11 [mem 0x80000000-0xfebfffff]
[ 0.270738] pci_bus 0000:02: resource 12 [mem 0xfed40000-0xfed44fff]
[ 0.270743] pci_bus 0000:03: resource 0 [io 0x1000-0x1fff]
[ 0.270749] pci_bus 0000:03: resource 1 [mem 0x80000000-0x800fffff]
[ 0.270877] NET: Registered protocol family 2
[ 0.271290] TCP established hash table entries: 16384 (order: 6, 262144 bytes)
[ 0.271468] TCP bind hash table entries: 16384 (order: 6, 262144 bytes)
[ 0.271590] TCP: Hash tables configured (established 16384 bind 16384)
[ 0.271737] TCP: reno registered
[ 0.271765] UDP hash table entries: 1024 (order: 3, 32768 bytes)
[ 0.271798] UDP-Lite hash table entries: 1024 (order: 3, 32768 bytes)
[ 0.272039] NET: Registered protocol family 1
[ 0.272077] pci 0000:00:02.0: Boot video device
[ 0.289283] PCI: CLS 64 bytes, default 64
[ 0.289395] Unpacking initramfs...
[ 0.725478] Freeing initrd memory: 11132k freed
[ 0.734956] audit: initializing netlink socket (disabled)
[ 0.734992] type=2000 audit(1369212350.632:1): initialized
[ 0.759329] HugeTLB registered 2 MB page size, pre-allocated 0 pages
[ 0.760150] VFS: Disk quotas dquot_6.5.2
[ 0.760239] Dquot-cache hash table entries: 512 (order 0, 4096 bytes)
[ 0.760439] msgmni has been set to 3987
[ 0.760940] alg: No test for stdrng (krng)
[ 0.761004] Block layer SCSI generic (bsg) driver version 0.4 loaded (major 252)
[ 0.761070] io scheduler noop registered
[ 0.761075] io scheduler deadline registered
[ 0.761109] io scheduler cfq registered (default)
[ 0.761332] pcieport 0000:00:1c.0: irq 40 for MSI/MSI-X
[ 0.761516] pci_hotplug: PCI Hot Plug PCI Core version: 0.5
[ 0.761568] pciehp: PCI Express Hot Plug Controller Driver version: 0.4
[ 0.761571] acpiphp: ACPI Hot Plug PCI Controller Driver version: 0.5
[ 0.762175] intel_idle: does not run on family 6 model 54
[ 0.762217] GHES: HEST is not enabled!
[ 0.762362] Serial: 8250/16550 driver, 4 ports, IRQ sharing enabled
[ 0.763432] Linux agpgart interface v0.103
[ 0.763733] i8042: PNP: No PS/2 controller found. Probing ports directly.
[ 0.766385] serio: i8042 KBD port at 0x60,0x64 irq 1
[ 0.766399] serio: i8042 AUX port at 0x60,0x64 irq 12
[ 0.766745] mousedev: PS/2 mouse device common for all mice
[ 0.766818] rtc_cmos 00:06: RTC can wake from S4
[ 0.767050] rtc_cmos 00:06: rtc core: registered rtc_cmos as rtc0
[ 0.767093] rtc0: alarms up to one month, y3k, 242 bytes nvram, hpet irqs
[ 0.767113] cpuidle: using governor ladder
[ 0.767116] cpuidle: using governor menu
[ 0.767202] drop_monitor: Initializing network drop monitor service
[ 0.767337] TCP: cubic registered
[ 0.767426] NET: Registered protocol family 10
[ 0.767820] mip6: Mobile IPv6
[ 0.767826] NET: Registered protocol family 17
[ 0.768510] PM: Hibernation image not present or could not be loaded.
[ 0.768535] registered taskstats version 1
[ 0.769497] rtc_cmos 00:06: setting system clock to 2013-05-22 08:45:50 UTC (1369212350)
[ 0.772107] Freeing unused kernel memory: 616k freed
[ 0.772371] Write protecting the kernel read-only data: 6144k
[ 0.776663] Freeing unused kernel memory: 452k freed
[ 0.781638] Freeing unused kernel memory: 524k freed
[ 0.808650] udevd[68]: starting version 175
[ 0.854615] ACPI: bus type usb registered
[ 0.854733] usbcore: registered new interface driver usbfs
[ 0.854788] usbcore: registered new interface driver hub
[ 0.855359] usbcore: registered new device driver usb
[ 0.856694] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
[ 0.861968] uhci_hcd: USB Universal Host Controller Interface driver
[ 0.862038] uhci_hcd 0000:00:1d.0: setting latency timer to 64
[ 0.862045] uhci_hcd 0000:00:1d.0: UHCI Host Controller
[ 0.862062] uhci_hcd 0000:00:1d.0: new USB bus registered, assigned bus number 1
[ 0.862141] uhci_hcd 0000:00:1d.0: irq 23, io base 0x000030a0
[ 0.862238] usb usb1: New USB device found, idVendor=1d6b, idProduct=0001
[ 0.862244] usb usb1: New USB device strings: Mfr=3, Product=2, SerialNumber=1
[ 0.862249] usb usb1: Product: UHCI Host Controller
[ 0.862253] usb usb1: Manufacturer: Linux 3.8-2-amd64 uhci_hcd
[ 0.862258] usb usb1: SerialNumber: 0000:00:1d.0
[ 0.862691] hub 1-0:1.0: USB hub found
[ 0.862710] hub 1-0:1.0: 2 ports detected
[ 0.863135] uhci_hcd 0000:00:1d.1: setting latency timer to 64
[ 0.863146] uhci_hcd 0000:00:1d.1: UHCI Host Controller
[ 0.863165] uhci_hcd 0000:00:1d.1: new USB bus registered, assigned bus number 2
[ 0.863259] uhci_hcd 0000:00:1d.1: irq 19, io base 0x00003080
[ 0.863389] usb usb2: New USB device found, idVendor=1d6b, idProduct=0001
[ 0.863397] usb usb2: New USB device strings: Mfr=3, Product=2, SerialNumber=1
[ 0.863405] usb usb2: Product: UHCI Host Controller
[ 0.863412] usb usb2: Manufacturer: Linux 3.8-2-amd64 uhci_hcd
[ 0.863418] usb usb2: SerialNumber: 0000:00:1d.1
[ 0.863861] hub 2-0:1.0: USB hub found
[ 0.863881] hub 2-0:1.0: 2 ports detected
[ 0.864341] uhci_hcd 0000:00:1d.2: setting latency timer to 64
[ 0.864352] uhci_hcd 0000:00:1d.2: UHCI Host Controller
[ 0.864371] uhci_hcd 0000:00:1d.2: new USB bus registered, assigned bus number 3
[ 0.864470] uhci_hcd 0000:00:1d.2: irq 18, io base 0x00003060
[ 0.864606] usb usb3: New USB device found, idVendor=1d6b, idProduct=0001
[ 0.864614] usb usb3: New USB device strings: Mfr=3, Product=2, SerialNumber=1
[ 0.864620] usb usb3: Product: UHCI Host Controller
[ 0.864626] usb usb3: Manufacturer: Linux 3.8-2-amd64 uhci_hcd
[ 0.864632] usb usb3: SerialNumber: 0000:00:1d.2
[ 0.866513] e1000e: Intel(R) PRO/1000 Network Driver - 2.1.4-k
[ 0.866519] e1000e: Copyright(c) 1999 - 2012 Intel Corporation.
[ 0.866563] e1000e 0000:01:00.0: Disabling ASPM L0s L1
[ 0.866808] e1000e 0000:01:00.0: Interrupt Throttling Rate (ints/sec) set to dynamic conservative mode
[ 0.866931] e1000e 0000:01:00.0: irq 41 for MSI/MSI-X
[ 0.866944] e1000e 0000:01:00.0: irq 42 for MSI/MSI-X
[ 0.866956] e1000e 0000:01:00.0: irq 43 for MSI/MSI-X
[ 0.867628] hub 3-0:1.0: USB hub found
[ 0.867652] hub 3-0:1.0: 2 ports detected
[ 0.877670] uhci_hcd 0000:00:1d.3: setting latency timer to 64
[ 0.877683] uhci_hcd 0000:00:1d.3: UHCI Host Controller
[ 0.877703] uhci_hcd 0000:00:1d.3: new USB bus registered, assigned bus number 4
[ 0.877807] uhci_hcd 0000:00:1d.3: irq 16, io base 0x00003040
[ 0.877949] usb usb4: New USB device found, idVendor=1d6b, idProduct=0001
[ 0.877958] usb usb4: New USB device strings: Mfr=3, Product=2, SerialNumber=1
[ 0.877966] usb usb4: Product: UHCI Host Controller
[ 0.877973] usb usb4: Manufacturer: Linux 3.8-2-amd64 uhci_hcd
[ 0.877979] usb usb4: SerialNumber: 0000:00:1d.3
[ 0.878489] hub 4-0:1.0: USB hub found
[ 0.878511] hub 4-0:1.0: 2 ports detected
[ 0.883148] SCSI subsystem initialized
[ 0.887062] ACPI: bus type scsi registered
[ 0.889244] libata version 3.00 loaded.
[ 0.891607] ahci 0000:00:1f.2: version 3.0
[ 0.891724] ahci 0000:00:1f.2: irq 44 for MSI/MSI-X
[ 0.891890] ahci: SSS flag set, parallel bus scan disabled
[ 0.892019] ahci 0000:00:1f.2: AHCI 0001.0100 32 slots 4 ports 3 Gbps 0x3 impl SATA mode
[ 0.892031] ahci 0000:00:1f.2: flags: 64bit ncq stag pm led clo pio slum part
[ 0.892043] ahci 0000:00:1f.2: setting latency timer to 64
[ 0.892154] ehci-pci: EHCI PCI platform driver
[ 0.894154] scsi0 : ahci
[ 0.894465] scsi1 : ahci
[ 0.894667] scsi2 : ahci
[ 0.894834] scsi3 : ahci
[ 0.894951] ata1: SATA max UDMA/133 abar m1024@0x80304000 port 0x80304100 irq 44
[ 0.894958] ata2: SATA max UDMA/133 abar m1024@0x80304000 port 0x80304180 irq 44
[ 0.894962] ata3: DUMMY
[ 0.894965] ata4: DUMMY
[ 0.895111] ehci-pci 0000:00:1d.7: setting latency timer to 64
[ 0.895122] ehci-pci 0000:00:1d.7: EHCI Host Controller
[ 0.895141] ehci-pci 0000:00:1d.7: new USB bus registered, assigned bus number 5
[ 0.895171] ehci-pci 0000:00:1d.7: debug port 1
[ 0.899120] ehci-pci 0000:00:1d.7: cache line size of 64 is not supported
[ 0.899148] ehci-pci 0000:00:1d.7: irq 23, io mem 0x80304400
[ 0.907970] ehci-pci 0000:00:1d.7: USB 2.0 started, EHCI 1.00
[ 0.908099] usb usb5: New USB device found, idVendor=1d6b, idProduct=0002
[ 0.908108] usb usb5: New USB device strings: Mfr=3, Product=2, SerialNumber=1
[ 0.908115] usb usb5: Product: EHCI Host Controller
[ 0.908122] usb usb5: Manufacturer: Linux 3.8-2-amd64 ehci_hcd
[ 0.908128] usb usb5: SerialNumber: 0000:00:1d.7
[ 0.908566] hub 5-0:1.0: USB hub found
[ 0.908584] hub 5-0:1.0: 8 ports detected
[ 0.921747] via_rhine: v1.10-LK1.5.0 2010-10-09 Written by Donald Becker
[ 0.921884] via-rhine 0000:03:00.0 (unregistered net_device): Woke system up. Reason: Unknown
[ 0.921897] via-rhine 0000:03:00.0 (unregistered net_device): Reset not complete yet. Trying harder.
[ 0.934809] via_rhine: 1024 cycles used @ rhine_reload_eeprom:672
[ 0.934831] via-rhine 0000:03:00.0 (unregistered net_device): Invalid MAC address: ff:ff:ff:ff:ff:ff
[ 0.934890] via-rhine 0000:03:00.0 (unregistered net_device): Using random MAC address: b2:a1:cc:1e:3b:23
[ 0.935436] via-rhine 0000:03:00.0 eth0: VIA Rhine III (Management Adapter) at 0x11300, b2:a1:cc:1e:3b:23, IRQ 20
[ 0.970485] via-rhine 0000:03:01.0 (unregistered net_device): Woke system up. Reason: Unknown
[ 0.970500] via-rhine 0000:03:01.0 (unregistered net_device): Reset not complete yet. Trying harder.
[ 0.980433] e1000e 0000:01:00.0 eth1: (PCI Express:2.5GT/s:Width x1) 00:22:4d:81:9e:39
[ 0.980442] e1000e 0000:01:00.0 eth1: Intel(R) PRO/1000 Network Connection
[ 0.980468] e1000e 0000:01:00.0 eth1: MAC: 3, PHY: 8, PBA No: FFFFFF-0FF
[ 0.983681] via_rhine: 1024 cycles used @ rhine_reload_eeprom:672
[ 0.983700] via-rhine 0000:03:01.0 (unregistered net_device): Invalid MAC address: ff:ff:ff:ff:ff:ff
[ 0.983787] via-rhine 0000:03:01.0 (unregistered net_device): Using random MAC address: 36:10:e5:8f:1c:87
[ 0.984185] via-rhine 0000:03:01.0 eth2: VIA Rhine III (Management Adapter) at 0x11200, 36:10:e5:8f:1c:87, IRQ 21
[ 1.018523] via-rhine 0000:03:02.0 (unregistered net_device): Woke system up. Reason: Unknown
[ 1.018535] via-rhine 0000:03:02.0 (unregistered net_device): Reset not complete yet. Trying harder.
[ 1.031174] via_rhine: 1024 cycles used @ rhine_reload_eeprom:672
[ 1.031190] via-rhine 0000:03:02.0 (unregistered net_device): Invalid MAC address: ff:ff:ff:ff:ff:ff
[ 1.031243] via-rhine 0000:03:02.0 (unregistered net_device): Using random MAC address: 32:1b:b4:3b:47:a9
[ 1.031585] via-rhine 0000:03:02.0 eth3: VIA Rhine III (Management Adapter) at 0x11100, 32:1b:b4:3b:47:a9, IRQ 22
[ 1.071381] via-rhine 0000:03:03.0 eth4: VIA Rhine III (Management Adapter) at 0x11000, 00:00:24:cf:a5:d7, IRQ 23
[ 1.072255] via-rhine 0000:03:03.0 eth4: MII PHY found at address 1, status 0x7849 advertising 05e1 Link 0000
[ 1.215286] ata1: SATA link up 1.5 Gbps (SStatus 113 SControl 300)
[ 1.251129] ata1.00: HPA detected: current 625140335, native 625142448
[ 1.251139] ata1.00: ATA-7: ST3320620AS, 3.AAK, max UDMA/133
[ 1.251144] ata1.00: 625140335 sectors, multi 16: LBA48 NCQ (depth 31/32)
[ 1.309314] ata1.00: configured for UDMA/133
[ 1.309560] scsi 0:0:0:0: Direct-Access ATA ST3320620AS 3.AA PQ: 0 ANSI: 5
[ 1.626436] ata2: SATA link down (SStatus 0 SControl 300)
[ 1.635663] sd 0:0:0:0: [sda] 625140335 512-byte logical blocks: (320 GB/298 GiB)
[ 1.635817] sd 0:0:0:0: [sda] Write Protect is off
[ 1.635824] sd 0:0:0:0: [sda] Mode Sense: 00 3a 00 00
[ 1.635887] sd 0:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
[ 1.679953] sda: sda1 sda2 < sda5 >
[ 1.680838] sd 0:0:0:0: [sda] Attached SCSI disk
[ 1.684736] sd 0:0:0:0: Attached scsi generic sg0 type 0
[ 1.714270] usb 2-1: new low-speed USB device number 2 using uhci_hcd
[ 1.730217] tsc: Refined TSC clocksource calibration: 2133.408 MHz
[ 1.730225] Switching to clocksource tsc
[ 1.889267] usb 2-1: New USB device found, idVendor=046d, idProduct=c019
[ 1.889275] usb 2-1: New USB device strings: Mfr=1, Product=2, SerialNumber=0
[ 1.889280] usb 2-1: Product: USB Optical Mouse
[ 1.889285] usb 2-1: Manufacturer: Logitech
[ 1.911379] usbcore: registered new interface driver usbhid
[ 1.911387] usbhid: USB HID core driver
[ 1.915796] input: Logitech USB Optical Mouse as /devices/pci0000:00/0000:00:1d.1/usb2/2-1/2-1:1.0/input/input0
[ 1.916059] hid-generic 0003:046D:C019.0001: input,hidraw0: USB HID v1.11 Mouse [Logitech USB Optical Mouse] on usb-0000:00:1d.1-1/input0
[ 2.001693] usb 3-2: new low-speed USB device number 2 using uhci_hcd
[ 2.021417] PM: Starting manual resume from disk
[ 2.021424] PM: Hibernation image partition 8:5 present
[ 2.021428] PM: Looking for hibernation image.
[ 2.021755] PM: Image not found (code -22)
[ 2.021760] PM: Hibernation image not present or could not be loaded.
[ 2.063047] kjournald starting. Commit interval 5 seconds
[ 2.063227] EXT3-fs (sda1): mounted filesystem with ordered data mode
[ 2.178336] usb 3-2: New USB device found, idVendor=046d, idProduct=c315
[ 2.178344] usb 3-2: New USB device strings: Mfr=1, Product=2, SerialNumber=0
[ 2.178349] usb 3-2: Product: Logitech USB Keyboard
[ 2.178354] usb 3-2: Manufacturer: Logitech
[ 2.195782] input: Logitech Logitech USB Keyboard as /devices/pci0000:00/0000:00:1d.2/usb3/3-2/3-2:1.0/input/input1
[ 2.195979] hid-generic 0003:046D:C315.0002: input,hidraw1: USB HID v1.10 Keyboard [Logitech Logitech USB Keyboard] on usb-0000:00:1d.2-2/input0
[ 3.893309] udevd[332]: starting version 175
[ 4.772423] i801_smbus 0000:00:1f.3: SMBus using PCI Interrupt
[ 4.772442] input: PC Speaker as /devices/platform/pcspkr/input/input2
[ 4.892903] input: Power Button as /devices/LNXSYSTM:00/LNXSYBUS:00/PNP0C0C:00/input/input3
[ 4.893088] ACPI: Power Button [PWRB]
[ 4.893327] input: Sleep Button as /devices/LNXSYSTM:00/LNXSYBUS:00/PNP0C0E:00/input/input4
[ 4.893501] ACPI: Sleep Button [SLPB]
[ 4.893693] input: Power Button as /devices/LNXSYSTM:00/LNXPWRBN:00/input/input5
[ 4.893839] ACPI: Power Button [PWRF]
[ 4.933832] shpchp: Standard Hot Plug PCI Controller Driver version: 0.4
[ 4.942161] microcode: CPU0 sig=0x30661, pf=0x4, revision=0x10d
[ 5.096190] [drm] Initialized drm 1.1.0 20060810
[ 5.098167] ACPI Warning: 0x0000000000000428-0x000000000000042f SystemIO conflicts with Region \PMIO 1 (20121018/utaddress-251)
[ 5.098180] ACPI Warning: 0x0000000000000428-0x000000000000042f SystemIO conflicts with Region \SWC1 2 (20121018/utaddress-251)
[ 5.098189] ACPI: If an ACPI driver is available for this device, you should use it instead of the native driver
[ 5.098195] ACPI Warning: 0x0000000000000530-0x000000000000053f SystemIO conflicts with Region \GPIO 1 (20121018/utaddress-251)
[ 5.098203] ACPI: If an ACPI driver is available for this device, you should use it instead of the native driver
[ 5.098207] ACPI Warning: 0x0000000000000500-0x000000000000052f SystemIO conflicts with Region \GPIO 1 (20121018/utaddress-251)
[ 5.098214] ACPI: If an ACPI driver is available for this device, you should use it instead of the native driver
[ 5.098218] lpc_ich: Resource conflict(s) found affecting gpio_ich
[ 5.137317] iTCO_vendor_support: vendor-support=0
[ 5.143429] iTCO_wdt: Intel TCO WatchDog Timer Driver v1.10
[ 5.143483] iTCO_wdt: Found a NM10 TCO device (Version=2, TCOBASE=0x0460)
[ 5.143855] iTCO_wdt: initialized. heartbeat=30 sec (nowayout=0)
[ 5.253252] platform microcode: firmware: agent aborted loading intel-ucode/06-36-01 (not found?)
[ 5.253417] microcode: CPU1 sig=0x30661, pf=0x4, revision=0x10d
[ 5.258302] platform microcode: firmware: agent aborted loading intel-ucode/06-36-01 (not found?)
[ 5.258490] microcode: CPU2 sig=0x30661, pf=0x4, revision=0x10d
[ 5.264737] platform microcode: firmware: agent aborted loading intel-ucode/06-36-01 (not found?)
[ 5.264945] microcode: CPU3 sig=0x30661, pf=0x4, revision=0x10d
[ 5.272461] platform microcode: firmware: agent aborted loading intel-ucode/06-36-01 (not found?)
[ 5.272784] microcode: Microcode Update Driver: v2.00 <tigran@aivazian.fsnet.co.uk>, Peter Oruba
[ 5.335100] coretemp coretemp.0: Unable to read TjMax from CPU 0
[ 5.335144] coretemp coretemp.0: Unable to read TjMax from CPU 2
[ 5.456582] gma500 0000:00:02.0: setting latency timer to 64
[ 5.456767] gma500 0000:00:02.0: irq 45 for MSI/MSI-X
[ 5.471394] ACPI Warning: _BQC returned an invalid level (20121018/video-486)
[ 5.471634] acpi device:1f: registered as cooling_device4
[ 5.472106] ACPI: Video Device [GFX0] (multi-head: yes rom: no post: no)
[ 5.472272] input: Video Bus as /devices/LNXSYSTM:00/LNXSYBUS:00/PNP0A08:00/LNXVIDEO:00/input/input6
[ 5.472513] [drm] Supports vblank timestamp caching Rev 1 (10.10.2010).
[ 5.472519] [drm] No driver support for vblank timestamp query.
[ 5.531871] Error: Driver 'pcspkr' is already registered, aborting...
[ 5.541585] gma500 0000:00:02.0: trying to get vblank count for disabled pipe 1
[ 5.541652] gma500 0000:00:02.0: trying to get vblank count for disabled pipe 1
[ 5.846849] fbcon: psbfb (fb0) is primary device
[ 6.577283] Console: switching to colour frame buffer device 170x48
[ 6.586319] gma500 0000:00:02.0: fb0: psbfb frame buffer device
[ 6.586323] gma500 0000:00:02.0: registered panic notifier
[ 6.586424] [drm] Initialized gma500 1.0.0 2011-06-06 for 0000:00:02.0 on minor 0
[ 6.586624] snd_hda_intel 0000:00:1b.0: irq 46 for MSI/MSI-X
[ 6.606457] input: HDA Digital PCBeep as /devices/pci0000:00/0000:00:1b.0/input/input7
[ 6.612295] input: HDA Intel Line as /devices/pci0000:00/0000:00:1b.0/sound/card0/input8
[ 6.612554] input: HDA Intel Rear Mic as /devices/pci0000:00/0000:00:1b.0/sound/card0/input9
[ 6.612757] input: HDA Intel Line Out as /devices/pci0000:00/0000:00:1b.0/sound/card0/input10
[ 6.612955] input: HDA Intel HDMI/DP,pcm=3 as /devices/pci0000:00/0000:00:1b.0/sound/card0/input11
[ 7.719587] Adding 3989500k swap on /dev/sda5. Priority:-1 extents:1 across:3989500k
[ 8.173096] EXT3-fs (sda1): using internal journal
[ 8.349792] loop: module loaded
[ 10.414004] RPC: Registered named UNIX socket transport module.
[ 10.414012] RPC: Registered udp transport module.
[ 10.414015] RPC: Registered tcp transport module.
[ 10.414018] RPC: Registered tcp NFSv4.1 backchannel transport module.
[ 10.561214] FS-Cache: Loaded
[ 10.578037] Key type dns_resolver registered
[ 10.623415] FS-Cache: Netfs 'nfs' registered for caching
[ 10.743484] Installing knfsd (copyright (C) 1996 okir@monad.swb.de).
[ 11.003519] IPv6: ADDRCONF(NETDEV_UP): eth1: link is not ready
[ 11.004085] via-rhine 0000:03:00.0 eth0: Reset not complete yet. Trying harder.
[ 11.063267] IPv6: ADDRCONF(NETDEV_UP): eth4: link is not ready
[ 12.896497] e1000e: eth1 NIC Link is Up 100 Mbps Full Duplex, Flow Control: None
[ 12.896509] e1000e 0000:01:00.0 eth1: 10/100 speed: disabling TSO
[ 12.896751] IPv6: ADDRCONF(NETDEV_CHANGE): eth1: link becomes ready
[ 32.830365] ------------[ cut here ]------------
[ 32.830379] WARNING: at /build/buildd-linux_3.8.13-1-amd64-YudJGj/linux-3.8.13/net/sched/sch_generic.c:254 dev_watchdog+0xe3/0x153()
[ 32.830384] Hardware name:
[ 32.830388] NETDEV WATCHDOG: eth0 (via-rhine): transmit queue 0 timed out
[ 32.830390] Modules linked in: nfsd auth_rpcgss nfs_acl nfs lockd dns_resolver fscache sunrpc loop snd_hda_codec_realtek snd_hda_codec_hdmi snd_hda_intel snd_hda_codec snd_hwdep snd_pcm gma500_gfx drm_kms_helper mperf coretemp processor iTCO_wdt iTCO_vendor_support lpc_ich drm snd_page_alloc snd_timer snd soundcore microcode shpchp video button psmouse i2c_algo_bit serio_raw mfd_core thermal_sys i2c_i801 pcspkr evdev i2c_core ext3 mbcache jbd hid_generic usbhid hid sg sd_mod crc_t10dif via_rhine mii ehci_pci ahci libahci libata scsi_mod e1000e uhci_hcd ehci_hcd usbcore usb_common
[ 32.830468] Pid: 0, comm: swapper/2 Not tainted 3.8-2-amd64 #1 Debian 3.8.13-1
[ 32.830471] Call Trace:
[ 32.830475] <IRQ> [<ffffffff8103ce54>] ? warn_slowpath_common+0x76/0x8a
[ 32.830489] [<ffffffff812dde0d>] ? netif_tx_lock+0x7a/0x7a
[ 32.830495] [<ffffffff8103cf00>] ? warn_slowpath_fmt+0x45/0x4a
[ 32.830501] [<ffffffff812dddfa>] ? netif_tx_lock+0x67/0x7a
[ 32.830510] [<ffffffff812ddef0>] ? dev_watchdog+0xe3/0x153
[ 32.830518] [<ffffffff81048287>] ? call_timer_fn+0x4b/0xf6
[ 32.830523] [<ffffffff812dde0d>] ? netif_tx_lock+0x7a/0x7a
[ 32.830530] [<ffffffff8104979a>] ? run_timer_softirq+0x18d/0x1d6
[ 32.830537] [<ffffffff811caef9>] ? timerqueue_add+0x79/0x98
[ 32.830543] [<ffffffff810436d3>] ? __do_softirq+0xcd/0x1d0
[ 32.830549] [<ffffffff81075158>] ? ktime_get+0x62/0x6a
[ 32.830556] [<ffffffff81079977>] ? clockevents_program_event+0x9a/0xb6
[ 32.830562] [<ffffffff81389ddc>] ? call_softirq+0x1c/0x30
[ 32.830568] [<ffffffff8100f9be>] ? do_softirq+0x3a/0x78
[ 32.830574] [<ffffffff8104389c>] ? irq_exit+0x3a/0x92
[ 32.830581] [<ffffffff81028af4>] ? smp_apic_timer_interrupt+0x73/0x81
[ 32.830587] [<ffffffff8138969d>] ? apic_timer_interrupt+0x6d/0x80
[ 32.830590] <EOI> [<ffffffff8101467e>] ? mwait_idle+0x80/0xac
[ 32.830601] [<ffffffff81014671>] ? mwait_idle+0x73/0xac
[ 32.830607] [<ffffffff81014df6>] ? cpu_idle+0xa6/0xe6
[ 32.830613] [<ffffffff8138372c>] ? _raw_spin_unlock_irqrestore+0xc/0xd
[ 32.830620] [<ffffffff81375984>] ? start_secondary+0x1e0/0x1e6
[ 32.830624] ---[ end trace 2b4e5ba10a703466 ]---
[ 32.842011] via-rhine 0000:03:00.0 eth0: Transmit timed out, status ffff, PHY status ffff, resetting...
[ 32.842126] via-rhine 0000:03:00.0 eth0: Reset not complete yet. Trying harder.
[ 84.735834] usb 5-4: new high-speed USB device number 4 using ehci-pci
[ 84.868386] usb 5-4: New USB device found, idVendor=0781, idProduct=5566
[ 84.868394] usb 5-4: New USB device strings: Mfr=1, Product=2, SerialNumber=3
[ 84.868400] usb 5-4: Product: Cruzer Slice
[ 84.868404] usb 5-4: Manufacturer: SanDisk
[ 84.868409] usb 5-4: SerialNumber: 200548584313BAB2E645
[ 84.935645] Initializing USB Mass Storage driver...
[ 84.935928] scsi4 : usb-storage 5-4:1.0
[ 84.936125] usbcore: registered new interface driver usb-storage
[ 84.936130] USB Mass Storage support registered.
[ 85.934233] scsi 4:0:0:0: Direct-Access SanDisk Cruzer Slice 1.02 PQ: 0 ANSI: 2
[ 85.935772] sd 4:0:0:0: Attached scsi generic sg1 type 0
[ 85.936503] sd 4:0:0:0: [sdb] 7813120 512-byte logical blocks: (4.00 GB/3.72 GiB)
[ 85.938247] sd 4:0:0:0: [sdb] Write Protect is off
[ 85.938257] sd 4:0:0:0: [sdb] Mode Sense: 03 00 00 00
[ 85.939355] sd 4:0:0:0: [sdb] No Caching mode page present
[ 85.939471] sd 4:0:0:0: [sdb] Assuming drive cache: write through
[ 85.944437] sd 4:0:0:0: [sdb] No Caching mode page present
[ 85.944528] sd 4:0:0:0: [sdb] Assuming drive cache: write through
[ 85.956349] sdb: sdb1
[ 85.959674] sd 4:0:0:0: [sdb] No Caching mode page present
[ 85.963197] sd 4:0:0:0: [sdb] Assuming drive cache: write through
[ 85.966622] sd 4:0:0:0: [sdb] Attached SCSI removable disk
[ 105.697573] FAT-fs (sdb1): utf8 is not a recommended IO charset for FAT filesystems, filesystem will be case sensitive!
0000-0cf7 : PCI Bus 0000:00
0000-001f : dma1
0020-0021 : pic1
0040-0043 : timer0
0050-0053 : timer1
0060-0060 : keyboard
0064-0064 : keyboard
0070-0077 : rtc0
0080-008f : dma page reg
00a0-00a1 : pic2
00c0-00df : dma2
00f0-00ff : fpu
03c0-03df : vga+
0400-047f : pnp 00:05
0400-0403 : ACPI PM1a_EVT_BLK
0404-0405 : ACPI PM1a_CNT_BLK
0408-040b : ACPI PM_TMR
0410-0415 : ACPI CPU throttle
0420-0420 : ACPI PM2_CNT_BLK
0428-042f : ACPI GPE0_BLK
0430-0433 : iTCO_wdt
0460-047f : iTCO_wdt
0500-057f : pnp 00:05
0600-061f : pnp 00:05
0680-069f : pnp 00:05
06a0-06af : pnp 00:06
06b0-06ff : pnp 00:06
0cf8-0cff : PCI conf1
0d00-ffff : PCI Bus 0000:00
1000-1fff : PCI Bus 0000:02
1000-1fff : PCI Bus 0000:03
1000-10ff : 0000:03:03.0
1000-10ff : via-rhine
1100-11ff : 0000:03:02.0
1100-11ff : via-rhine
1200-12ff : 0000:03:01.0
1200-12ff : via-rhine
1300-13ff : 0000:03:00.0
1300-13ff : via-rhine
2000-2fff : PCI Bus 0000:01
2000-201f : 0000:01:00.0
3000-301f : 0000:00:1f.3
3000-301f : i801_smbus
3020-302f : 0000:00:1f.2
3020-302f : ahci
3040-305f : 0000:00:1d.3
3040-305f : uhci_hcd
3060-307f : 0000:00:1d.2
3060-307f : uhci_hcd
3080-309f : 0000:00:1d.1
3080-309f : uhci_hcd
30a0-30bf : 0000:00:1d.0
30a0-30bf : uhci_hcd
30c0-30c7 : 0000:00:1f.2
30c0-30c7 : ahci
30c8-30cf : 0000:00:1f.2
30c8-30cf : ahci
30d0-30d7 : 0000:00:02.0
30d8-30db : 0000:00:1f.2
30d8-30db : ahci
30dc-30df : 0000:00:1f.2
30dc-30df : ahci
ffff-ffff : pnp 00:05
ffff-ffff : pnp 00:05
ffff-ffff : pnp 00:05
00:00.0 Host bridge: Intel Corporation Cedarview DRAM Controller (rev 03)
Subsystem: Intel Corporation Device 2011
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap- 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0
00:02.0 VGA compatible controller: Intel Corporation Cedarview Integrated Graphics Controller (rev 09) (prog-if 00 [VGA controller])
Subsystem: Intel Corporation Device 2011
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0
Interrupt: pin A routed to IRQ 11
Region 0: Memory at 80200000 (32-bit, non-prefetchable) [size=1M]
Region 1: I/O ports at 30d0 [size=8]
Expansion ROM at <unassigned> [disabled]
Capabilities: [d0] Power Management version 2
Flags: PMEClk- DSI+ D1- D2- AuxCurrent=0mA PME(D0-,D1-,D2-,D3hot-,D3cold-)
Status: D0 NoSoftRst- PME-Enable- DSel=0 DScale=0 PME-
Capabilities: [b0] Vendor Specific Information: Len=07 <?>
Capabilities: [90] MSI: Enable- Count=1/1 Maskable- 64bit-
Address: 00000000 Data: 0000
00:1b.0 Audio device: Intel Corporation N10/ICH 7 Family High Definition Audio Controller (rev 02)
Subsystem: Intel Corporation Device 2011
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0, Cache Line Size: 64 bytes
Interrupt: pin A routed to IRQ 22
Region 0: Memory at 80400000 (64-bit, non-prefetchable) [size=16K]
Capabilities: [50] Power Management version 2
Flags: PMEClk- DSI- D1- D2- AuxCurrent=55mA PME(D0+,D1-,D2-,D3hot+,D3cold+)
Status: D0 NoSoftRst- PME-Enable- DSel=0 DScale=0 PME-
Capabilities: [60] MSI: Enable- Count=1/1 Maskable- 64bit+
Address: 0000000000000000 Data: 0000
Capabilities: [70] Express (v1) Root Complex Integrated Endpoint, MSI 00
DevCap: MaxPayload 128 bytes, PhantFunc 0, Latency L0s <64ns, L1 <1us
ExtTag- RBE- FLReset-
DevCtl: Report errors: Correctable- Non-Fatal- Fatal- Unsupported-
RlxdOrd- ExtTag- PhantFunc- AuxPwr- NoSnoop+
MaxPayload 128 bytes, MaxReadReq 128 bytes
DevSta: CorrErr- UncorrErr- FatalErr- UnsuppReq- AuxPwr+ TransPend-
LnkCap: Port #0, Speed unknown, Width x0, ASPM unknown, Latency L0 <64ns, L1 <1us
ClockPM- Surprise- LLActRep- BwNot-
LnkCtl: ASPM Disabled; Disabled- Retrain- CommClk-
ExtSynch- ClockPM- AutWidDis- BWInt- AutBWInt-
LnkSta: Speed unknown, Width x0, TrErr- Train- SlotClk- DLActive- BWMgmt- ABWMgmt-
Capabilities: [100 v1] Virtual Channel
Caps: LPEVC=0 RefClk=100ns PATEntryBits=1
Arb: Fixed- WRR32- WRR64- WRR128-
Ctrl: ArbSelect=Fixed
Status: InProgress-
VC0: Caps: PATOffset=00 MaxTimeSlots=1 RejSnoopTrans-
Arb: Fixed- WRR32- WRR64- WRR128- TWRR128- WRR256-
Ctrl: Enable+ ID=0 ArbSelect=Fixed TC/VC=01
Status: NegoPending- InProgress-
VC1: Caps: PATOffset=00 MaxTimeSlots=1 RejSnoopTrans-
Arb: Fixed- WRR32- WRR64- WRR128- TWRR128- WRR256-
Ctrl: Enable+ ID=1 ArbSelect=Fixed TC/VC=02
Status: NegoPending- InProgress-
Capabilities: [130 v1] Root Complex Link
Desc: PortNumber=0f ComponentID=02 EltType=Config
Link0: Desc: TargetPort=00 TargetComponent=02 AssocRCRB- LinkType=MemMapped LinkValid+
Addr: 00000000fed1c000
Kernel driver in use: HDA Intel
00:1c.0 PCI bridge: Intel Corporation N10/ICH 7 Family PCI Express Port 1 (rev 02) (prog-if 00 [Normal decode])
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx+
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0, Cache Line Size: 64 bytes
Bus: primary=00, secondary=01, subordinate=01, sec-latency=0
I/O behind bridge: 00002000-00002fff
Memory behind bridge: 80100000-801fffff
Prefetchable memory behind bridge: 0000000080500000-00000000806fffff
Secondary status: 66MHz- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- <SERR- <PERR-
BridgeCtl: Parity- SERR- NoISA+ VGA- MAbort- >Reset- FastB2B-
PriDiscTmr- SecDiscTmr- DiscTmrStat- DiscTmrSERREn-
Capabilities: [40] Express (v1) Root Port (Slot+), MSI 00
DevCap: MaxPayload 128 bytes, PhantFunc 0, Latency L0s unlimited, L1 unlimited
ExtTag- RBE- FLReset-
DevCtl: Report errors: Correctable- Non-Fatal- Fatal- Unsupported-
RlxdOrd- ExtTag- PhantFunc- AuxPwr- NoSnoop-
MaxPayload 128 bytes, MaxReadReq 128 bytes
DevSta: CorrErr+ UncorrErr- FatalErr- UnsuppReq- AuxPwr+ TransPend-
LnkCap: Port #1, Speed 2.5GT/s, Width x1, ASPM L0s L1, Latency L0 <256ns, L1 <4us
ClockPM- Surprise- LLActRep+ BwNot-
LnkCtl: ASPM L0s L1 Enabled; RCB 64 bytes Disabled- Retrain- CommClk+
ExtSynch- ClockPM- AutWidDis- BWInt- AutBWInt-
LnkSta: Speed 2.5GT/s, Width x1, TrErr- Train- SlotClk+ DLActive+ BWMgmt- ABWMgmt-
SltCap: AttnBtn- PwrCtrl- MRL- AttnInd- PwrInd- HotPlug+ Surprise+
Slot #0, PowerLimit 6.500W; Interlock- NoCompl-
SltCtl: Enable: AttnBtn- PwrFlt- MRL- PresDet- CmdCplt- HPIrq- LinkChg-
Control: AttnInd Unknown, PwrInd Unknown, Power- Interlock-
SltSta: Status: AttnBtn- PowerFlt- MRL- CmdCplt- PresDet+ Interlock-
Changed: MRL- PresDet+ LinkState+
RootCtl: ErrCorrectable- ErrNon-Fatal- ErrFatal- PMEIntEna+ CRSVisible-
RootCap: CRSVisible-
RootSta: PME ReqID 0000, PMEStatus- PMEPending-
Capabilities: [80] MSI: Enable+ Count=1/1 Maskable- 64bit-
Address: fee0f00c Data: 4169
Capabilities: [90] Subsystem: Intel Corporation Device 2011
Capabilities: [a0] Power Management version 2
Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA PME(D0+,D1-,D2-,D3hot+,D3cold+)
Status: D0 NoSoftRst- PME-Enable- DSel=0 DScale=0 PME-
Capabilities: [100 v1] Virtual Channel
Caps: LPEVC=0 RefClk=100ns PATEntryBits=1
Arb: Fixed+ WRR32- WRR64- WRR128-
Ctrl: ArbSelect=Fixed
Status: InProgress-
VC0: Caps: PATOffset=00 MaxTimeSlots=1 RejSnoopTrans-
Arb: Fixed+ WRR32- WRR64- WRR128- TWRR128- WRR256-
Ctrl: Enable+ ID=0 ArbSelect=Fixed TC/VC=ff
Status: NegoPending- InProgress-
VC1: Caps: PATOffset=00 MaxTimeSlots=1 RejSnoopTrans-
Arb: Fixed+ WRR32- WRR64- WRR128- TWRR128- WRR256-
Ctrl: Enable- ID=0 ArbSelect=Fixed TC/VC=00
Status: NegoPending- InProgress-
Capabilities: [180 v1] Root Complex Link
Desc: PortNumber=01 ComponentID=02 EltType=Config
Link0: Desc: TargetPort=00 TargetComponent=02 AssocRCRB- LinkType=MemMapped LinkValid+
Addr: 00000000fed1c001
Kernel driver in use: pcieport
00:1d.0 USB Controller: Intel Corporation N10/ICH 7 Family USB UHCI Controller #1 (rev 02) (prog-if 00 [UHCI])
Subsystem: Intel Corporation Device 2011
Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap- 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0
Interrupt: pin A routed to IRQ 23
Region 4: I/O ports at 30a0 [size=32]
Kernel driver in use: uhci_hcd
00:1d.1 USB Controller: Intel Corporation N10/ICH 7 Family USB UHCI Controller #2 (rev 02) (prog-if 00 [UHCI])
Subsystem: Intel Corporation Device 2011
Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap- 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0
Interrupt: pin B routed to IRQ 19
Region 4: I/O ports at 3080 [size=32]
Kernel driver in use: uhci_hcd
00:1d.2 USB Controller: Intel Corporation N10/ICH 7 Family USB UHCI Controller #3 (rev 02) (prog-if 00 [UHCI])
Subsystem: Intel Corporation Device 2011
Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap- 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0
Interrupt: pin C routed to IRQ 18
Region 4: I/O ports at 3060 [size=32]
Kernel driver in use: uhci_hcd
00:1d.3 USB Controller: Intel Corporation N10/ICH 7 Family USB UHCI Controller #4 (rev 02) (prog-if 00 [UHCI])
Subsystem: Intel Corporation Device 2011
Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap- 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0
Interrupt: pin D routed to IRQ 16
Region 4: I/O ports at 3040 [size=32]
Kernel driver in use: uhci_hcd
00:1d.7 USB Controller: Intel Corporation N10/ICH 7 Family USB2 EHCI Controller (rev 02) (prog-if 20 [EHCI])
Subsystem: Intel Corporation Device 2011
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0
Interrupt: pin A routed to IRQ 23
Region 0: Memory at 80304400 (32-bit, non-prefetchable) [size=1K]
Capabilities: [50] Power Management version 2
Flags: PMEClk- DSI- D1- D2- AuxCurrent=375mA PME(D0+,D1-,D2-,D3hot+,D3cold+)
Status: D0 NoSoftRst- PME-Enable- DSel=0 DScale=0 PME+
Capabilities: [58] Debug port: BAR=1 offset=00a0
Kernel driver in use: ehci_hcd
00:1e.0 PCI bridge: Intel Corporation 82801 Mobile PCI Bridge (rev e2) (prog-if 01 [Subtractive decode])
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR+ FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0
Bus: primary=00, secondary=02, subordinate=03, sec-latency=32
I/O behind bridge: 00001000-00001fff
Memory behind bridge: 80000000-800fffff
Prefetchable memory behind bridge: 00000000fff00000-00000000000fffff
Secondary status: 66MHz- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort+ <SERR- <PERR-
BridgeCtl: Parity- SERR- NoISA+ VGA- MAbort- >Reset- FastB2B-
PriDiscTmr- SecDiscTmr- DiscTmrStat- DiscTmrSERREn-
Capabilities: [50] Subsystem: Intel Corporation Device 2011
00:1f.0 ISA bridge: Intel Corporation NM10 Family LPC Controller (rev 02)
Subsystem: Intel Corporation Device 2011
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR+ FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0
Capabilities: [e0] Vendor Specific Information: Len=0c <?>
00:1f.2 SATA controller: Intel Corporation N10/ICH7 Family SATA AHCI Controller (rev 02) (prog-if 01 [AHCI 1.0])
Subsystem: Intel Corporation Device 2011
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx+
Status: Cap+ 66MHz+ UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0
Interrupt: pin B routed to IRQ 28
Region 0: I/O ports at 30c8 [size=8]
Region 1: I/O ports at 30dc [size=4]
Region 2: I/O ports at 30c0 [size=8]
Region 3: I/O ports at 30d8 [size=4]
Region 4: I/O ports at 3020 [size=16]
Region 5: Memory at 80304000 (32-bit, non-prefetchable) [size=1K]
Capabilities: [80] MSI: Enable+ Count=1/1 Maskable- 64bit-
Address: fee0f00c Data: 41a1
Capabilities: [70] Power Management version 2
Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA PME(D0-,D1-,D2-,D3hot+,D3cold-)
Status: D0 NoSoftRst- PME-Enable- DSel=0 DScale=0 PME-
Kernel driver in use: ahci
00:1f.3 SMBus: Intel Corporation N10/ICH 7 Family SMBus Controller (rev 02)
Subsystem: Intel Corporation Device 2011
Control: I/O+ Mem- BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap- 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Interrupt: pin B routed to IRQ 19
Region 4: I/O ports at 3000 [size=32]
Kernel driver in use: i801_smbus
01:00.0 Ethernet controller: Intel Corporation 82574L Gigabit Network Connection
Subsystem: Intel Corporation Device 2011
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx+
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0, Cache Line Size: 64 bytes
Interrupt: pin A routed to IRQ 16
Region 0: Memory at 80120000 (32-bit, non-prefetchable) [size=128K]
Region 1: Memory at 80100000 (32-bit, non-prefetchable) [size=128K]
Region 2: I/O ports at 2000 [size=32]
Region 3: Memory at 80140000 (32-bit, non-prefetchable) [size=16K]
Capabilities: [c8] Power Management version 2
Flags: PMEClk- DSI+ D1- D2- AuxCurrent=0mA PME(D0+,D1-,D2-,D3hot+,D3cold+)
Status: D0 NoSoftRst- PME-Enable- DSel=0 DScale=1 PME-
Capabilities: [d0] MSI: Enable- Count=1/1 Maskable- 64bit+
Address: 0000000000000000 Data: 0000
Capabilities: [e0] Express (v1) Endpoint, MSI 00
DevCap: MaxPayload 256 bytes, PhantFunc 0, Latency L0s <512ns, L1 <64us
ExtTag- AttnBtn- AttnInd- PwrInd- RBE+ FLReset-
DevCtl: Report errors: Correctable+ Non-Fatal+ Fatal+ Unsupported+
RlxdOrd+ ExtTag- PhantFunc- AuxPwr- NoSnoop+
MaxPayload 128 bytes, MaxReadReq 512 bytes
DevSta: CorrErr+ UncorrErr- FatalErr- UnsuppReq+ AuxPwr+ TransPend-
LnkCap: Port #0, Speed 2.5GT/s, Width x1, ASPM L0s L1, Latency L0 <128ns, L1 <64us
ClockPM- Surprise- LLActRep- BwNot-
LnkCtl: ASPM L0s L1 Enabled; RCB 64 bytes Disabled- Retrain- CommClk+
ExtSynch- ClockPM- AutWidDis- BWInt- AutBWInt-
LnkSta: Speed 2.5GT/s, Width x1, TrErr- Train- SlotClk+ DLActive- BWMgmt- ABWMgmt-
Capabilities: [a0] MSI-X: Enable+ Count=5 Masked-
Vector table: BAR=3 offset=00000000
PBA: BAR=3 offset=00002000
Capabilities: [100 v1] Advanced Error Reporting
UESta: DLP- SDES- TLP- FCP- CmpltTO- CmpltAbrt- UnxCmplt- RxOF- MalfTLP- ECRC- UnsupReq- ACSViol-
UEMsk: DLP- SDES- TLP- FCP- CmpltTO- CmpltAbrt- UnxCmplt- RxOF- MalfTLP- ECRC- UnsupReq- ACSViol-
UESvrt: DLP+ SDES- TLP- FCP+ CmpltTO- CmpltAbrt- UnxCmplt- RxOF+ MalfTLP+ ECRC- UnsupReq- ACSViol-
CESta: RxErr- BadTLP- BadDLLP- Rollover- Timeout- NonFatalErr+
CEMsk: RxErr- BadTLP- BadDLLP- Rollover- Timeout- NonFatalErr+
AERCap: First Error Pointer: 00, GenCap- CGenEn- ChkCap- ChkEn-
Capabilities: [140 v1] Device Serial Number 00-22-4d-ff-ff-81-9e-39
Kernel driver in use: e1000e
02:00.0 PCI bridge: Texas Instruments PCI2250 PCI-to-PCI Bridge (rev 02) (prog-if 00 [Normal decode])
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 32, Cache Line Size: 64 bytes
Bus: primary=02, secondary=03, subordinate=03, sec-latency=0
I/O behind bridge: 00001000-00001fff
Memory behind bridge: 80000000-800fffff
Prefetchable memory behind bridge: fff00000-000fffff
Secondary status: 66MHz- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- <SERR- <PERR-
BridgeCtl: Parity- SERR- NoISA+ VGA- MAbort- >Reset- FastB2B-
PriDiscTmr- SecDiscTmr- DiscTmrStat- DiscTmrSERREn-
Capabilities: [dc] Power Management version 1
Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA PME(D0-,D1-,D2-,D3hot-,D3cold-)
Status: D0 NoSoftRst- PME-Enable- DSel=0 DScale=0 PME-
03:00.0 Ethernet controller: VIA Technologies, Inc. VT6105M [Rhine-III] (rev 96)
Subsystem: VIA Technologies, Inc. Device 0106
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV+ VGASnoop- ParErr- Stepping+ SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 32 (750ns min, 2000ns max), Cache Line Size: 64 bytes
Interrupt: pin A routed to IRQ 20
Region 0: I/O ports at 1300 [size=256]
Region 1: Memory at 80000300 (32-bit, non-prefetchable) [size=256]
Capabilities: [40] Power Management version 2
Flags: PMEClk- DSI- D1+ D2+ AuxCurrent=0mA PME(D0+,D1+,D2+,D3hot+,D3cold+)
Status: D0 NoSoftRst- PME-Enable- DSel=0 DScale=0 PME-
03:01.0 Ethernet controller: VIA Technologies, Inc. VT6105M [Rhine-III] (rev 96)
Subsystem: VIA Technologies, Inc. Device 0106
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV+ VGASnoop- ParErr- Stepping+ SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 32 (750ns min, 2000ns max), Cache Line Size: 64 bytes
Interrupt: pin A routed to IRQ 21
Region 0: I/O ports at 1200 [size=256]
Region 1: Memory at 80000200 (32-bit, non-prefetchable) [size=256]
Capabilities: [40] Power Management version 2
Flags: PMEClk- DSI- D1+ D2+ AuxCurrent=0mA PME(D0+,D1+,D2+,D3hot+,D3cold+)
Status: D0 NoSoftRst- PME-Enable- DSel=0 DScale=0 PME-
03:02.0 Ethernet controller: VIA Technologies, Inc. VT6105M [Rhine-III] (rev 96)
Subsystem: VIA Technologies, Inc. Device 0106
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV+ VGASnoop- ParErr- Stepping+ SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 32 (750ns min, 2000ns max), Cache Line Size: 64 bytes
Interrupt: pin A routed to IRQ 22
Region 0: I/O ports at 1100 [size=256]
Region 1: Memory at 80000100 (32-bit, non-prefetchable) [size=256]
Capabilities: [40] Power Management version 2
Flags: PMEClk- DSI- D1+ D2+ AuxCurrent=0mA PME(D0+,D1+,D2+,D3hot+,D3cold+)
Status: D0 NoSoftRst- PME-Enable- DSel=0 DScale=0 PME-
03:03.0 Ethernet controller: VIA Technologies, Inc. VT6105M [Rhine-III] (rev 96)
Subsystem: VIA Technologies, Inc. Device 0106
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV+ VGASnoop- ParErr- Stepping+ SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 32 (750ns min, 2000ns max), Cache Line Size: 64 bytes
Interrupt: pin A routed to IRQ 23
Region 0: I/O ports at 1000 [size=256]
Region 1: Memory at 80000000 (32-bit, non-prefetchable) [size=256]
Capabilities: [40] Power Management version 2
Flags: PMEClk- DSI- D1+ D2+ AuxCurrent=0mA PME(D0+,D1+,D2+,D3hot+,D3cold+)
Status: D0 NoSoftRst- PME-Enable- DSel=0 DScale=0 PME-
Kernel driver in use: via-rhine
00:00.0 Host bridge: Intel Corporation Atom Processor D2xxx/N2xxx DRAM Controller (rev 03)
Subsystem: Intel Corporation Device 2011
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap- 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0
00:02.0 VGA compatible controller: Intel Corporation Atom Processor D2xxx/N2xxx Integrated Graphics Controller (rev 09) (prog-if 00 [VGA controller])
Subsystem: Intel Corporation Device 2011
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx+
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0
Interrupt: pin A routed to IRQ 45
Region 0: Memory at 80200000 (32-bit, non-prefetchable) [size=1M]
Region 1: I/O ports at 30d0 [size=8]
Expansion ROM at <unassigned> [disabled]
Capabilities: [d0] Power Management version 2
Flags: PMEClk- DSI+ D1- D2- AuxCurrent=0mA PME(D0-,D1-,D2-,D3hot-,D3cold-)
Status: D0 NoSoftRst- PME-Enable- DSel=0 DScale=0 PME-
Capabilities: [b0] Vendor Specific Information: Len=07 <?>
Capabilities: [90] MSI: Enable+ Count=1/1 Maskable- 64bit-
Address: fee0f00c Data: 4142
Kernel driver in use: gma500
00:1b.0 Audio device: Intel Corporation NM10/ICH7 Family High Definition Audio Controller (rev 02)
Subsystem: Intel Corporation Device 2011
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx+
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0, Cache Line Size: 64 bytes
Interrupt: pin A routed to IRQ 46
Region 0: Memory at 80400000 (64-bit, non-prefetchable) [size=16K]
Capabilities: [50] Power Management version 2
Flags: PMEClk- DSI- D1- D2- AuxCurrent=55mA PME(D0+,D1-,D2-,D3hot+,D3cold+)
Status: D0 NoSoftRst- PME-Enable- DSel=0 DScale=0 PME-
Capabilities: [60] MSI: Enable+ Count=1/1 Maskable- 64bit+
Address: 00000000fee0f00c Data: 4152
Capabilities: [70] Express (v1) Root Complex Integrated Endpoint, MSI 00
DevCap: MaxPayload 128 bytes, PhantFunc 0, Latency L0s <64ns, L1 <1us
ExtTag- RBE- FLReset-
DevCtl: Report errors: Correctable- Non-Fatal- Fatal- Unsupported-
RlxdOrd- ExtTag- PhantFunc- AuxPwr- NoSnoop+
MaxPayload 128 bytes, MaxReadReq 128 bytes
DevSta: CorrErr- UncorrErr- FatalErr- UnsuppReq- AuxPwr+ TransPend-
LnkCap: Port #0, Speed unknown, Width x0, ASPM unknown, Latency L0 <64ns, L1 <1us
ClockPM- Surprise- LLActRep- BwNot-
LnkCtl: ASPM Disabled; Disabled- Retrain- CommClk-
ExtSynch- ClockPM- AutWidDis- BWInt- AutBWInt-
LnkSta: Speed unknown, Width x0, TrErr- Train- SlotClk- DLActive- BWMgmt- ABWMgmt-
Capabilities: [100 v1] Virtual Channel
Caps: LPEVC=0 RefClk=100ns PATEntryBits=1
Arb: Fixed- WRR32- WRR64- WRR128-
Ctrl: ArbSelect=Fixed
Status: InProgress-
VC0: Caps: PATOffset=00 MaxTimeSlots=1 RejSnoopTrans-
Arb: Fixed- WRR32- WRR64- WRR128- TWRR128- WRR256-
Ctrl: Enable+ ID=0 ArbSelect=Fixed TC/VC=01
Status: NegoPending- InProgress-
VC1: Caps: PATOffset=00 MaxTimeSlots=1 RejSnoopTrans-
Arb: Fixed- WRR32- WRR64- WRR128- TWRR128- WRR256-
Ctrl: Enable+ ID=1 ArbSelect=Fixed TC/VC=02
Status: NegoPending- InProgress-
Capabilities: [130 v1] Root Complex Link
Desc: PortNumber=0f ComponentID=02 EltType=Config
Link0: Desc: TargetPort=00 TargetComponent=02 AssocRCRB- LinkType=MemMapped LinkValid+
Addr: 00000000fed1c000
Kernel driver in use: snd_hda_intel
00:1c.0 PCI bridge: Intel Corporation NM10/ICH7 Family PCI Express Port 1 (rev 02) (prog-if 00 [Normal decode])
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx+
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0, Cache Line Size: 64 bytes
Bus: primary=00, secondary=01, subordinate=01, sec-latency=0
I/O behind bridge: 00002000-00002fff
Memory behind bridge: 80100000-801fffff
Prefetchable memory behind bridge: 0000000080500000-00000000806fffff
Secondary status: 66MHz- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- <SERR- <PERR-
BridgeCtl: Parity- SERR- NoISA+ VGA- MAbort- >Reset- FastB2B-
PriDiscTmr- SecDiscTmr- DiscTmrStat- DiscTmrSERREn-
Capabilities: [40] Express (v1) Root Port (Slot+), MSI 00
DevCap: MaxPayload 128 bytes, PhantFunc 0, Latency L0s unlimited, L1 unlimited
ExtTag- RBE- FLReset-
DevCtl: Report errors: Correctable- Non-Fatal- Fatal- Unsupported-
RlxdOrd- ExtTag- PhantFunc- AuxPwr- NoSnoop-
MaxPayload 128 bytes, MaxReadReq 128 bytes
DevSta: CorrErr+ UncorrErr- FatalErr- UnsuppReq- AuxPwr+ TransPend-
LnkCap: Port #1, Speed 2.5GT/s, Width x1, ASPM L0s L1, Latency L0 <256ns, L1 <4us
ClockPM- Surprise- LLActRep+ BwNot-
LnkCtl: ASPM L0s L1 Enabled; RCB 64 bytes Disabled- Retrain- CommClk+
ExtSynch- ClockPM- AutWidDis- BWInt- AutBWInt-
LnkSta: Speed 2.5GT/s, Width x1, TrErr- Train- SlotClk+ DLActive+ BWMgmt- ABWMgmt-
SltCap: AttnBtn- PwrCtrl- MRL- AttnInd- PwrInd- HotPlug+ Surprise+
Slot #0, PowerLimit 6.500W; Interlock- NoCompl-
SltCtl: Enable: AttnBtn- PwrFlt- MRL- PresDet- CmdCplt- HPIrq- LinkChg-
Control: AttnInd Unknown, PwrInd Unknown, Power- Interlock-
SltSta: Status: AttnBtn- PowerFlt- MRL- CmdCplt- PresDet+ Interlock-
Changed: MRL- PresDet+ LinkState+
RootCtl: ErrCorrectable- ErrNon-Fatal- ErrFatal- PMEIntEna+ CRSVisible-
RootCap: CRSVisible-
RootSta: PME ReqID 0000, PMEStatus- PMEPending-
Capabilities: [80] MSI: Enable+ Count=1/1 Maskable- 64bit-
Address: fee0f00c Data: 4181
Capabilities: [90] Subsystem: Intel Corporation Device 2011
Capabilities: [a0] Power Management version 2
Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA PME(D0+,D1-,D2-,D3hot+,D3cold+)
Status: D0 NoSoftRst- PME-Enable- DSel=0 DScale=0 PME-
Capabilities: [100 v1] Virtual Channel
Caps: LPEVC=0 RefClk=100ns PATEntryBits=1
Arb: Fixed+ WRR32- WRR64- WRR128-
Ctrl: ArbSelect=Fixed
Status: InProgress-
VC0: Caps: PATOffset=00 MaxTimeSlots=1 RejSnoopTrans-
Arb: Fixed+ WRR32- WRR64- WRR128- TWRR128- WRR256-
Ctrl: Enable+ ID=0 ArbSelect=Fixed TC/VC=ff
Status: NegoPending- InProgress-
VC1: Caps: PATOffset=00 MaxTimeSlots=1 RejSnoopTrans-
Arb: Fixed+ WRR32- WRR64- WRR128- TWRR128- WRR256-
Ctrl: Enable- ID=0 ArbSelect=Fixed TC/VC=00
Status: NegoPending- InProgress-
Capabilities: [180 v1] Root Complex Link
Desc: PortNumber=01 ComponentID=02 EltType=Config
Link0: Desc: TargetPort=00 TargetComponent=02 AssocRCRB- LinkType=MemMapped LinkValid+
Addr: 00000000fed1c001
Kernel driver in use: pcieport
00:1d.0 USB controller: Intel Corporation NM10/ICH7 Family USB UHCI Controller #1 (rev 02) (prog-if 00 [UHCI])
Subsystem: Intel Corporation Device 2011
Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap- 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0
Interrupt: pin A routed to IRQ 23
Region 4: I/O ports at 30a0 [size=32]
Kernel driver in use: uhci_hcd
00:1d.1 USB controller: Intel Corporation NM10/ICH7 Family USB UHCI Controller #2 (rev 02) (prog-if 00 [UHCI])
Subsystem: Intel Corporation Device 2011
Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap- 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0
Interrupt: pin B routed to IRQ 19
Region 4: I/O ports at 3080 [size=32]
Kernel driver in use: uhci_hcd
00:1d.2 USB controller: Intel Corporation NM10/ICH7 Family USB UHCI Controller #3 (rev 02) (prog-if 00 [UHCI])
Subsystem: Intel Corporation Device 2011
Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap- 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0
Interrupt: pin C routed to IRQ 18
Region 4: I/O ports at 3060 [size=32]
Kernel driver in use: uhci_hcd
00:1d.3 USB controller: Intel Corporation NM10/ICH7 Family USB UHCI Controller #4 (rev 02) (prog-if 00 [UHCI])
Subsystem: Intel Corporation Device 2011
Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap- 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0
Interrupt: pin D routed to IRQ 16
Region 4: I/O ports at 3040 [size=32]
Kernel driver in use: uhci_hcd
00:1d.7 USB controller: Intel Corporation NM10/ICH7 Family USB2 EHCI Controller (rev 02) (prog-if 20 [EHCI])
Subsystem: Intel Corporation Device 2011
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0
Interrupt: pin A routed to IRQ 23
Region 0: Memory at 80304400 (32-bit, non-prefetchable) [size=1K]
Capabilities: [50] Power Management version 2
Flags: PMEClk- DSI- D1- D2- AuxCurrent=375mA PME(D0+,D1-,D2-,D3hot+,D3cold+)
Status: D0 NoSoftRst- PME-Enable- DSel=0 DScale=0 PME+
Capabilities: [58] Debug port: BAR=1 offset=00a0
Kernel driver in use: ehci-pci
00:1e.0 PCI bridge: Intel Corporation 82801 Mobile PCI Bridge (rev e2) (prog-if 01 [Subtractive decode])
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR+ FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0
Bus: primary=00, secondary=02, subordinate=03, sec-latency=32
I/O behind bridge: 00001000-00001fff
Memory behind bridge: 80000000-800fffff
Prefetchable memory behind bridge: 00000000fff00000-00000000000fffff
Secondary status: 66MHz- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort+ <SERR- <PERR-
BridgeCtl: Parity- SERR- NoISA+ VGA- MAbort- >Reset- FastB2B-
PriDiscTmr- SecDiscTmr- DiscTmrStat- DiscTmrSERREn-
Capabilities: [50] Subsystem: Intel Corporation Device 2011
00:1f.0 ISA bridge: Intel Corporation NM10 Family LPC Controller (rev 02)
Subsystem: Intel Corporation Device 2011
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR+ FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0
Capabilities: [e0] Vendor Specific Information: Len=0c <?>
Kernel driver in use: lpc_ich
00:1f.2 SATA controller: Intel Corporation NM10/ICH7 Family SATA Controller [AHCI mode] (rev 02) (prog-if 01 [AHCI 1.0])
Subsystem: Intel Corporation Device 2011
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx+
Status: Cap+ 66MHz+ UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0
Interrupt: pin B routed to IRQ 44
Region 0: I/O ports at 30c8 [size=8]
Region 1: I/O ports at 30dc [size=4]
Region 2: I/O ports at 30c0 [size=8]
Region 3: I/O ports at 30d8 [size=4]
Region 4: I/O ports at 3020 [size=16]
Region 5: Memory at 80304000 (32-bit, non-prefetchable) [size=1K]
Capabilities: [80] MSI: Enable+ Count=1/1 Maskable- 64bit-
Address: fee0f00c Data: 41c1
Capabilities: [70] Power Management version 2
Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA PME(D0-,D1-,D2-,D3hot+,D3cold-)
Status: D0 NoSoftRst- PME-Enable- DSel=0 DScale=0 PME-
Kernel driver in use: ahci
00:1f.3 SMBus: Intel Corporation NM10/ICH7 Family SMBus Controller (rev 02)
Subsystem: Intel Corporation Device 2011
Control: I/O+ Mem- BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap- 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Interrupt: pin B routed to IRQ 19
Region 4: I/O ports at 3000 [size=32]
Kernel driver in use: i801_smbus
01:00.0 Ethernet controller: Intel Corporation 82574L Gigabit Network Connection
Subsystem: Intel Corporation Device 2011
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx+
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0, Cache Line Size: 64 bytes
Interrupt: pin A routed to IRQ 16
Region 0: Memory at 80120000 (32-bit, non-prefetchable) [size=128K]
Region 1: Memory at 80100000 (32-bit, non-prefetchable) [size=128K]
Region 2: I/O ports at 2000 [size=32]
Region 3: Memory at 80140000 (32-bit, non-prefetchable) [size=16K]
Capabilities: [c8] Power Management version 2
Flags: PMEClk- DSI+ D1- D2- AuxCurrent=0mA PME(D0+,D1-,D2-,D3hot+,D3cold+)
Status: D0 NoSoftRst- PME-Enable- DSel=0 DScale=1 PME-
Capabilities: [d0] MSI: Enable- Count=1/1 Maskable- 64bit+
Address: 0000000000000000 Data: 0000
Capabilities: [e0] Express (v1) Endpoint, MSI 00
DevCap: MaxPayload 256 bytes, PhantFunc 0, Latency L0s <512ns, L1 <64us
ExtTag- AttnBtn- AttnInd- PwrInd- RBE+ FLReset-
DevCtl: Report errors: Correctable+ Non-Fatal+ Fatal+ Unsupported+
RlxdOrd+ ExtTag- PhantFunc- AuxPwr- NoSnoop+
MaxPayload 128 bytes, MaxReadReq 512 bytes
DevSta: CorrErr+ UncorrErr- FatalErr- UnsuppReq+ AuxPwr+ TransPend-
LnkCap: Port #0, Speed 2.5GT/s, Width x1, ASPM L0s L1, Latency L0 <128ns, L1 <64us
ClockPM- Surprise- LLActRep- BwNot-
LnkCtl: ASPM L0s L1 Enabled; RCB 64 bytes Disabled- Retrain- CommClk+
ExtSynch- ClockPM- AutWidDis- BWInt- AutBWInt-
LnkSta: Speed 2.5GT/s, Width x1, TrErr- Train- SlotClk+ DLActive- BWMgmt- ABWMgmt-
Capabilities: [a0] MSI-X: Enable+ Count=5 Masked-
Vector table: BAR=3 offset=00000000
PBA: BAR=3 offset=00002000
Capabilities: [100 v1] Advanced Error Reporting
UESta: DLP- SDES- TLP- FCP- CmpltTO- CmpltAbrt- UnxCmplt- RxOF- MalfTLP- ECRC- UnsupReq- ACSViol-
UEMsk: DLP- SDES- TLP- FCP- CmpltTO- CmpltAbrt- UnxCmplt- RxOF- MalfTLP- ECRC- UnsupReq- ACSViol-
UESvrt: DLP+ SDES- TLP- FCP+ CmpltTO- CmpltAbrt- UnxCmplt- RxOF+ MalfTLP+ ECRC- UnsupReq- ACSViol-
CESta: RxErr- BadTLP+ BadDLLP- Rollover- Timeout+ NonFatalErr+
CEMsk: RxErr- BadTLP- BadDLLP- Rollover- Timeout- NonFatalErr+
AERCap: First Error Pointer: 00, GenCap- CGenEn- ChkCap- ChkEn-
Capabilities: [140 v1] Device Serial Number 00-22-4d-ff-ff-81-9e-39
Kernel driver in use: e1000e
02:00.0 PCI bridge: Texas Instruments PCI2250 PCI-to-PCI Bridge (rev 02) (prog-if 00 [Normal decode])
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 32, Cache Line Size: 64 bytes
Bus: primary=02, secondary=03, subordinate=03, sec-latency=0
I/O behind bridge: 00001000-00001fff
Memory behind bridge: 80000000-800fffff
Prefetchable memory behind bridge: fff00000-000fffff
Secondary status: 66MHz- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- <SERR- <PERR-
BridgeCtl: Parity- SERR- NoISA+ VGA- MAbort- >Reset- FastB2B-
PriDiscTmr- SecDiscTmr- DiscTmrStat- DiscTmrSERREn-
Capabilities: [dc] Power Management version 1
Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA PME(D0-,D1-,D2-,D3hot-,D3cold-)
Status: D0 NoSoftRst- PME-Enable- DSel=0 DScale=0 PME-
03:00.0 Ethernet controller: VIA Technologies, Inc. VT6105M [Rhine-III] (rev 96)
Subsystem: VIA Technologies, Inc. Device 0106
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV+ VGASnoop- ParErr- Stepping+ SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 32 (750ns min, 2000ns max), Cache Line Size: 64 bytes
Interrupt: pin A routed to IRQ 20
Region 0: I/O ports at 1300 [size=256]
Region 1: Memory at 80000300 (32-bit, non-prefetchable) [size=256]
Capabilities: [40] Power Management version 2
Flags: PMEClk- DSI- D1+ D2+ AuxCurrent=0mA PME(D0+,D1+,D2+,D3hot+,D3cold+)
Status: D0 NoSoftRst- PME-Enable- DSel=0 DScale=0 PME-
Kernel driver in use: via-rhine
03:01.0 Ethernet controller: VIA Technologies, Inc. VT6105M [Rhine-III] (rev 96)
Subsystem: VIA Technologies, Inc. Device 0106
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV+ VGASnoop- ParErr- Stepping+ SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 32 (750ns min, 2000ns max), Cache Line Size: 64 bytes
Interrupt: pin A routed to IRQ 21
Region 0: I/O ports at 1200 [size=256]
Region 1: Memory at 80000200 (32-bit, non-prefetchable) [size=256]
Capabilities: [40] Power Management version 2
Flags: PMEClk- DSI- D1+ D2+ AuxCurrent=0mA PME(D0+,D1+,D2+,D3hot+,D3cold+)
Status: D0 NoSoftRst- PME-Enable- DSel=0 DScale=0 PME-
Kernel driver in use: via-rhine
03:02.0 Ethernet controller: VIA Technologies, Inc. VT6105M [Rhine-III] (rev 96)
Subsystem: VIA Technologies, Inc. Device 0106
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV+ VGASnoop- ParErr- Stepping+ SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 32 (750ns min, 2000ns max), Cache Line Size: 64 bytes
Interrupt: pin A routed to IRQ 22
Region 0: I/O ports at 1100 [size=256]
Region 1: Memory at 80000100 (32-bit, non-prefetchable) [size=256]
Capabilities: [40] Power Management version 2
Flags: PMEClk- DSI- D1+ D2+ AuxCurrent=0mA PME(D0+,D1+,D2+,D3hot+,D3cold+)
Status: D0 NoSoftRst- PME-Enable- DSel=0 DScale=0 PME-
Kernel driver in use: via-rhine
03:03.0 Ethernet controller: VIA Technologies, Inc. VT6105M [Rhine-III] (rev 96)
Subsystem: VIA Technologies, Inc. Device 0106
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV+ VGASnoop- ParErr- Stepping+ SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 32 (750ns min, 2000ns max), Cache Line Size: 64 bytes
Interrupt: pin A routed to IRQ 23
Region 0: I/O ports at 1000 [size=256]
Region 1: Memory at 80000000 (32-bit, non-prefetchable) [size=256]
Capabilities: [40] Power Management version 2
Flags: PMEClk- DSI- D1+ D2+ AuxCurrent=0mA PME(D0+,D1+,D2+,D3hot+,D3cold+)
Status: D0 NoSoftRst- PME-Enable- DSel=0 DScale=0 PME-
Kernel driver in use: via-rhine
00:00.0 Host bridge: Intel Corporation Atom Processor D2xxx/N2xxx DRAM Controller (rev 03)
Subsystem: Intel Corporation Device 2011
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap- 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0
00:02.0 VGA compatible controller: Intel Corporation Atom Processor D2xxx/N2xxx Integrated Graphics Controller (rev 09) (prog-if 00 [VGA controller])
Subsystem: Intel Corporation Device 2011
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx+
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0
Interrupt: pin A routed to IRQ 45
Region 0: Memory at 80200000 (32-bit, non-prefetchable) [size=1M]
Region 1: I/O ports at 30d0 [size=8]
Expansion ROM at <unassigned> [disabled]
Capabilities: [d0] Power Management version 2
Flags: PMEClk- DSI+ D1- D2- AuxCurrent=0mA PME(D0-,D1-,D2-,D3hot-,D3cold-)
Status: D0 NoSoftRst- PME-Enable- DSel=0 DScale=0 PME-
Capabilities: [b0] Vendor Specific Information: Len=07 <?>
Capabilities: [90] MSI: Enable+ Count=1/1 Maskable- 64bit-
Address: fee0f00c Data: 4199
Kernel driver in use: gma500
00:1b.0 Audio device: Intel Corporation NM10/ICH7 Family High Definition Audio Controller (rev 02)
Subsystem: Intel Corporation Device 2011
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx+
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0, Cache Line Size: 64 bytes
Interrupt: pin A routed to IRQ 46
Region 0: Memory at 80400000 (64-bit, non-prefetchable) [size=16K]
Capabilities: [50] Power Management version 2
Flags: PMEClk- DSI- D1- D2- AuxCurrent=55mA PME(D0+,D1-,D2-,D3hot+,D3cold+)
Status: D0 NoSoftRst- PME-Enable- DSel=0 DScale=0 PME-
Capabilities: [60] MSI: Enable+ Count=1/1 Maskable- 64bit+
Address: 00000000fee0f00c Data: 41a1
Capabilities: [70] Express (v1) Root Complex Integrated Endpoint, MSI 00
DevCap: MaxPayload 128 bytes, PhantFunc 0, Latency L0s <64ns, L1 <1us
ExtTag- RBE- FLReset-
DevCtl: Report errors: Correctable- Non-Fatal- Fatal- Unsupported-
RlxdOrd- ExtTag- PhantFunc- AuxPwr- NoSnoop+
MaxPayload 128 bytes, MaxReadReq 128 bytes
DevSta: CorrErr- UncorrErr- FatalErr- UnsuppReq- AuxPwr+ TransPend-
LnkCap: Port #0, Speed unknown, Width x0, ASPM unknown, Latency L0 <64ns, L1 <1us
ClockPM- Surprise- LLActRep- BwNot-
LnkCtl: ASPM Disabled; Disabled- Retrain- CommClk-
ExtSynch- ClockPM- AutWidDis- BWInt- AutBWInt-
LnkSta: Speed unknown, Width x0, TrErr- Train- SlotClk- DLActive- BWMgmt- ABWMgmt-
Capabilities: [100 v1] Virtual Channel
Caps: LPEVC=0 RefClk=100ns PATEntryBits=1
Arb: Fixed- WRR32- WRR64- WRR128-
Ctrl: ArbSelect=Fixed
Status: InProgress-
VC0: Caps: PATOffset=00 MaxTimeSlots=1 RejSnoopTrans-
Arb: Fixed- WRR32- WRR64- WRR128- TWRR128- WRR256-
Ctrl: Enable+ ID=0 ArbSelect=Fixed TC/VC=01
Status: NegoPending- InProgress-
VC1: Caps: PATOffset=00 MaxTimeSlots=1 RejSnoopTrans-
Arb: Fixed- WRR32- WRR64- WRR128- TWRR128- WRR256-
Ctrl: Enable+ ID=1 ArbSelect=Fixed TC/VC=02
Status: NegoPending- InProgress-
Capabilities: [130 v1] Root Complex Link
Desc: PortNumber=0f ComponentID=02 EltType=Config
Link0: Desc: TargetPort=00 TargetComponent=02 AssocRCRB- LinkType=MemMapped LinkValid+
Addr: 00000000fed1c000
Kernel driver in use: snd_hda_intel
00:1c.0 PCI bridge: Intel Corporation NM10/ICH7 Family PCI Express Port 1 (rev 02) (prog-if 00 [Normal decode])
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx+
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0, Cache Line Size: 64 bytes
Bus: primary=00, secondary=01, subordinate=01, sec-latency=0
I/O behind bridge: 00002000-00002fff
Memory behind bridge: 80100000-801fffff
Prefetchable memory behind bridge: 0000000080500000-00000000806fffff
Secondary status: 66MHz- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- <SERR- <PERR-
BridgeCtl: Parity- SERR- NoISA+ VGA- MAbort- >Reset- FastB2B-
PriDiscTmr- SecDiscTmr- DiscTmrStat- DiscTmrSERREn-
Capabilities: [40] Express (v1) Root Port (Slot+), MSI 00
DevCap: MaxPayload 128 bytes, PhantFunc 0, Latency L0s unlimited, L1 unlimited
ExtTag- RBE- FLReset-
DevCtl: Report errors: Correctable- Non-Fatal- Fatal- Unsupported-
RlxdOrd- ExtTag- PhantFunc- AuxPwr- NoSnoop-
MaxPayload 128 bytes, MaxReadReq 128 bytes
DevSta: CorrErr+ UncorrErr- FatalErr- UnsuppReq- AuxPwr+ TransPend-
LnkCap: Port #1, Speed 2.5GT/s, Width x1, ASPM L0s L1, Latency L0 <256ns, L1 <4us
ClockPM- Surprise- LLActRep+ BwNot-
LnkCtl: ASPM L0s L1 Enabled; RCB 64 bytes Disabled- Retrain- CommClk+
ExtSynch- ClockPM- AutWidDis- BWInt- AutBWInt-
LnkSta: Speed 2.5GT/s, Width x1, TrErr- Train- SlotClk+ DLActive+ BWMgmt- ABWMgmt-
SltCap: AttnBtn- PwrCtrl- MRL- AttnInd- PwrInd- HotPlug+ Surprise+
Slot #0, PowerLimit 6.500W; Interlock- NoCompl-
SltCtl: Enable: AttnBtn- PwrFlt- MRL- PresDet- CmdCplt- HPIrq- LinkChg-
Control: AttnInd Unknown, PwrInd Unknown, Power- Interlock-
SltSta: Status: AttnBtn- PowerFlt- MRL- CmdCplt- PresDet+ Interlock-
Changed: MRL- PresDet+ LinkState+
RootCtl: ErrCorrectable- ErrNon-Fatal- ErrFatal- PMEIntEna+ CRSVisible-
RootCap: CRSVisible-
RootSta: PME ReqID 0000, PMEStatus- PMEPending-
Capabilities: [80] MSI: Enable+ Count=1/1 Maskable- 64bit-
Address: fee0f00c Data: 4159
Capabilities: [90] Subsystem: Intel Corporation Device 2011
Capabilities: [a0] Power Management version 2
Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA PME(D0+,D1-,D2-,D3hot+,D3cold+)
Status: D0 NoSoftRst- PME-Enable- DSel=0 DScale=0 PME-
Capabilities: [100 v1] Virtual Channel
Caps: LPEVC=0 RefClk=100ns PATEntryBits=1
Arb: Fixed+ WRR32- WRR64- WRR128-
Ctrl: ArbSelect=Fixed
Status: InProgress-
VC0: Caps: PATOffset=00 MaxTimeSlots=1 RejSnoopTrans-
Arb: Fixed+ WRR32- WRR64- WRR128- TWRR128- WRR256-
Ctrl: Enable+ ID=0 ArbSelect=Fixed TC/VC=ff
Status: NegoPending- InProgress-
VC1: Caps: PATOffset=00 MaxTimeSlots=1 RejSnoopTrans-
Arb: Fixed+ WRR32- WRR64- WRR128- TWRR128- WRR256-
Ctrl: Enable- ID=0 ArbSelect=Fixed TC/VC=00
Status: NegoPending- InProgress-
Capabilities: [180 v1] Root Complex Link
Desc: PortNumber=01 ComponentID=02 EltType=Config
Link0: Desc: TargetPort=00 TargetComponent=02 AssocRCRB- LinkType=MemMapped LinkValid+
Addr: 00000000fed1c001
Kernel driver in use: pcieport
00:1d.0 USB controller: Intel Corporation NM10/ICH7 Family USB UHCI Controller #1 (rev 02) (prog-if 00 [UHCI])
Subsystem: Intel Corporation Device 2011
Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap- 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0
Interrupt: pin A routed to IRQ 23
Region 4: I/O ports at 30a0 [size=32]
Kernel driver in use: uhci_hcd
00:1d.1 USB controller: Intel Corporation NM10/ICH7 Family USB UHCI Controller #2 (rev 02) (prog-if 00 [UHCI])
Subsystem: Intel Corporation Device 2011
Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap- 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0
Interrupt: pin B routed to IRQ 19
Region 4: I/O ports at 3080 [size=32]
Kernel driver in use: uhci_hcd
00:1d.2 USB controller: Intel Corporation NM10/ICH7 Family USB UHCI Controller #3 (rev 02) (prog-if 00 [UHCI])
Subsystem: Intel Corporation Device 2011
Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap- 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0
Interrupt: pin C routed to IRQ 18
Region 4: I/O ports at 3060 [size=32]
Kernel driver in use: uhci_hcd
00:1d.3 USB controller: Intel Corporation NM10/ICH7 Family USB UHCI Controller #4 (rev 02) (prog-if 00 [UHCI])
Subsystem: Intel Corporation Device 2011
Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap- 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0
Interrupt: pin D routed to IRQ 16
Region 4: I/O ports at 3040 [size=32]
Kernel driver in use: uhci_hcd
00:1d.7 USB controller: Intel Corporation NM10/ICH7 Family USB2 EHCI Controller (rev 02) (prog-if 20 [EHCI])
Subsystem: Intel Corporation Device 2011
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0
Interrupt: pin A routed to IRQ 23
Region 0: Memory at 80304400 (32-bit, non-prefetchable) [size=1K]
Capabilities: [50] Power Management version 2
Flags: PMEClk- DSI- D1- D2- AuxCurrent=375mA PME(D0+,D1-,D2-,D3hot+,D3cold+)
Status: D0 NoSoftRst- PME-Enable- DSel=0 DScale=0 PME-
Capabilities: [58] Debug port: BAR=1 offset=00a0
Kernel driver in use: ehci_hcd
00:1e.0 PCI bridge: Intel Corporation 82801 Mobile PCI Bridge (rev e2) (prog-if 01 [Subtractive decode])
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR+ FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0
Bus: primary=00, secondary=02, subordinate=03, sec-latency=32
I/O behind bridge: 00001000-00001fff
Memory behind bridge: 80000000-800fffff
Prefetchable memory behind bridge: 00000000fff00000-00000000000fffff
Secondary status: 66MHz- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort+ <SERR- <PERR-
BridgeCtl: Parity- SERR- NoISA+ VGA- MAbort- >Reset- FastB2B-
PriDiscTmr- SecDiscTmr- DiscTmrStat- DiscTmrSERREn-
Capabilities: [50] Subsystem: Intel Corporation Device 2011
00:1f.0 ISA bridge: Intel Corporation NM10 Family LPC Controller (rev 02)
Subsystem: Intel Corporation Device 2011
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR+ FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0
Capabilities: [e0] Vendor Specific Information: Len=0c <?>
00:1f.2 SATA controller: Intel Corporation NM10/ICH7 Family SATA Controller [AHCI mode] (rev 02) (prog-if 01 [AHCI 1.0])
Subsystem: Intel Corporation Device 2011
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx+
Status: Cap+ 66MHz+ UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0
Interrupt: pin B routed to IRQ 44
Region 0: I/O ports at 30c8 [size=8]
Region 1: I/O ports at 30dc [size=4]
Region 2: I/O ports at 30c0 [size=8]
Region 3: I/O ports at 30d8 [size=4]
Region 4: I/O ports at 3020 [size=16]
Region 5: Memory at 80304000 (32-bit, non-prefetchable) [size=1K]
Capabilities: [80] MSI: Enable+ Count=1/1 Maskable- 64bit-
Address: fee0f00c Data: 4179
Capabilities: [70] Power Management version 2
Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA PME(D0-,D1-,D2-,D3hot+,D3cold-)
Status: D0 NoSoftRst- PME-Enable- DSel=0 DScale=0 PME-
Kernel driver in use: ahci
00:1f.3 SMBus: Intel Corporation NM10/ICH7 Family SMBus Controller (rev 02)
Subsystem: Intel Corporation Device 2011
Control: I/O+ Mem- BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap- 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Interrupt: pin B routed to IRQ 19
Region 4: I/O ports at 3000 [size=32]
Kernel driver in use: i801_smbus
01:00.0 Ethernet controller: Intel Corporation 82574L Gigabit Network Connection
Subsystem: Intel Corporation Device 2011
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx+
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0, Cache Line Size: 64 bytes
Interrupt: pin A routed to IRQ 16
Region 0: Memory at 80120000 (32-bit, non-prefetchable) [size=128K]
Region 1: Memory at 80100000 (32-bit, non-prefetchable) [size=128K]
Region 2: I/O ports at 2000 [size=32]
Region 3: Memory at 80140000 (32-bit, non-prefetchable) [size=16K]
Capabilities: [c8] Power Management version 2
Flags: PMEClk- DSI+ D1- D2- AuxCurrent=0mA PME(D0+,D1-,D2-,D3hot+,D3cold+)
Status: D0 NoSoftRst- PME-Enable- DSel=0 DScale=1 PME-
Capabilities: [d0] MSI: Enable- Count=1/1 Maskable- 64bit+
Address: 0000000000000000 Data: 0000
Capabilities: [e0] Express (v1) Endpoint, MSI 00
DevCap: MaxPayload 256 bytes, PhantFunc 0, Latency L0s <512ns, L1 <64us
ExtTag- AttnBtn- AttnInd- PwrInd- RBE+ FLReset-
DevCtl: Report errors: Correctable+ Non-Fatal+ Fatal+ Unsupported+
RlxdOrd+ ExtTag- PhantFunc- AuxPwr- NoSnoop+
MaxPayload 128 bytes, MaxReadReq 512 bytes
DevSta: CorrErr+ UncorrErr- FatalErr- UnsuppReq+ AuxPwr+ TransPend-
LnkCap: Port #0, Speed 2.5GT/s, Width x1, ASPM L0s L1, Latency L0 <128ns, L1 <64us
ClockPM- Surprise- LLActRep- BwNot-
LnkCtl: ASPM L0s L1 Enabled; RCB 64 bytes Disabled- Retrain- CommClk+
ExtSynch- ClockPM- AutWidDis- BWInt- AutBWInt-
LnkSta: Speed 2.5GT/s, Width x1, TrErr- Train- SlotClk+ DLActive- BWMgmt- ABWMgmt-
Capabilities: [a0] MSI-X: Enable+ Count=5 Masked-
Vector table: BAR=3 offset=00000000
PBA: BAR=3 offset=00002000
Capabilities: [100 v1] Advanced Error Reporting
UESta: DLP- SDES- TLP- FCP- CmpltTO- CmpltAbrt- UnxCmplt- RxOF- MalfTLP- ECRC- UnsupReq- ACSViol-
UEMsk: DLP- SDES- TLP- FCP- CmpltTO- CmpltAbrt- UnxCmplt- RxOF- MalfTLP- ECRC- UnsupReq- ACSViol-
UESvrt: DLP+ SDES- TLP- FCP+ CmpltTO- CmpltAbrt- UnxCmplt- RxOF+ MalfTLP+ ECRC- UnsupReq- ACSViol-
CESta: RxErr- BadTLP- BadDLLP- Rollover- Timeout+ NonFatalErr+
CEMsk: RxErr- BadTLP- BadDLLP- Rollover- Timeout- NonFatalErr+
AERCap: First Error Pointer: 00, GenCap- CGenEn- ChkCap- ChkEn-
Capabilities: [140 v1] Device Serial Number 00-22-4d-ff-ff-81-9e-39
Kernel driver in use: e1000e
02:00.0 PCI bridge: Texas Instruments PCI2250 PCI-to-PCI Bridge (rev 02) (prog-if 00 [Normal decode])
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 32, Cache Line Size: 64 bytes
Bus: primary=02, secondary=03, subordinate=03, sec-latency=0
I/O behind bridge: 00001000-00001fff
Memory behind bridge: 80000000-800fffff
Prefetchable memory behind bridge: fff00000-000fffff
Secondary status: 66MHz- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- <SERR- <PERR-
BridgeCtl: Parity- SERR- NoISA+ VGA- MAbort- >Reset- FastB2B-
PriDiscTmr- SecDiscTmr- DiscTmrStat- DiscTmrSERREn-
Capabilities: [dc] Power Management version 1
Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA PME(D0-,D1-,D2-,D3hot-,D3cold-)
Status: D0 NoSoftRst- PME-Enable- DSel=0 DScale=0 PME-
03:00.0 Ethernet controller: VIA Technologies, Inc. VT6105M [Rhine-III] (rev 96)
Subsystem: VIA Technologies, Inc. Device 0106
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV+ VGASnoop- ParErr- Stepping+ SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 32 (750ns min, 2000ns max), Cache Line Size: 64 bytes
Interrupt: pin A routed to IRQ 20
Region 0: I/O ports at 1300 [size=256]
Region 1: Memory at 80000300 (32-bit, non-prefetchable) [size=256]
Capabilities: [40] Power Management version 2
Flags: PMEClk- DSI- D1+ D2+ AuxCurrent=0mA PME(D0+,D1+,D2+,D3hot+,D3cold+)
Status: D0 NoSoftRst- PME-Enable- DSel=0 DScale=0 PME-
Kernel driver in use: via-rhine
03:01.0 Ethernet controller: VIA Technologies, Inc. VT6105M [Rhine-III] (rev 96)
Subsystem: VIA Technologies, Inc. Device 0106
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV+ VGASnoop- ParErr- Stepping+ SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 32 (750ns min, 2000ns max), Cache Line Size: 64 bytes
Interrupt: pin A routed to IRQ 21
Region 0: I/O ports at 1200 [size=256]
Region 1: Memory at 80000200 (32-bit, non-prefetchable) [size=256]
Capabilities: [40] Power Management version 2
Flags: PMEClk- DSI- D1+ D2+ AuxCurrent=0mA PME(D0+,D1+,D2+,D3hot+,D3cold+)
Status: D0 NoSoftRst- PME-Enable- DSel=0 DScale=0 PME-
Kernel driver in use: via-rhine
03:02.0 Ethernet controller: VIA Technologies, Inc. VT6105M [Rhine-III] (rev 96)
Subsystem: VIA Technologies, Inc. Device 0106
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV+ VGASnoop- ParErr- Stepping+ SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 32 (750ns min, 2000ns max), Cache Line Size: 64 bytes
Interrupt: pin A routed to IRQ 22
Region 0: I/O ports at 1100 [size=256]
Region 1: Memory at 80000100 (32-bit, non-prefetchable) [size=256]
Capabilities: [40] Power Management version 2
Flags: PMEClk- DSI- D1+ D2+ AuxCurrent=0mA PME(D0+,D1+,D2+,D3hot+,D3cold+)
Status: D0 NoSoftRst- PME-Enable- DSel=0 DScale=0 PME-
Kernel driver in use: via-rhine
03:03.0 Ethernet controller: VIA Technologies, Inc. VT6105M [Rhine-III] (rev 96)
Subsystem: VIA Technologies, Inc. Device 0106
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV+ VGASnoop- ParErr- Stepping+ SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 32 (750ns min, 2000ns max), Cache Line Size: 64 bytes
Interrupt: pin A routed to IRQ 23
Region 0: I/O ports at 1000 [size=256]
Region 1: Memory at 80000000 (32-bit, non-prefetchable) [size=256]
Capabilities: [40] Power Management version 2
Flags: PMEClk- DSI- D1+ D2+ AuxCurrent=0mA PME(D0+,D1+,D2+,D3hot+,D3cold+)
Status: D0 NoSoftRst- PME-Enable- DSel=0 DScale=0 PME-
Kernel driver in use: via-rhine
Linux debian 2.6.32-5-amd64 #1 SMP Fri May 10 08:43:19 UTC 2013 x86_64 GNU/Linux
Linux debian 3.8-2-amd64 #1 SMP Debian 3.8.13-1 x86_64 GNU/Linux
Reply to: