Bug#708058: cannot set freq 48000 to ep 0x86; beeps cause temporary gnome session hang
Package: src:linux
Version: 3.2.41-2
Severity: normal
I booted with Logitech webcam plugged in. The following message appears
continuously in my kernel log:
May 12 20:49:35 araminta kernel: [174158.144151] 3:3:4: cannot set freq 48000
to ep 0x86
Also, this caused my Gnome session to temporarily hang when tab
completing over /var/log (probably when attempting to beep). Initial Gnome
login was also very slow; I think the cause is the same.
I unplugged my USB webcam. The kernel log showed then showed:
May 12 20:49:40 araminta kernel: [174163.144045] 3:3:4: cannot set freq 48000
to ep 0x86
May 12 20:49:40 araminta kernel: [174163.883550] usb 2-4: USB disconnect,
device number 3
May 12 20:49:40 araminta kernel: [174163.887534] 3:3:4: cannot set freq 48000
to ep 0x86
May 12 20:49:40 araminta kernel: [174163.888054] 3:3:4: cannot set freq 48000
to ep 0x86
May 12 20:49:40 araminta kernel: [174163.888438] 3:3:4: cannot set freq 48000
to ep 0x86
May 12 20:49:40 araminta kernel: [174163.889238] 3:3:4: usb_set_interface
failed
May 12 20:49:40 araminta kernel: [174163.889289] 3:3:4: usb_set_interface
failed
May 12 20:49:40 araminta kernel: [174163.889424] 3:3:4: usb_set_interface
failed
May 12 20:49:40 araminta kernel: [174163.889745] 3:3:4: usb_set_interface
failed
May 12 20:49:40 araminta kernel: [174163.890100] 3:3:4: usb_set_interface
failed
[etc]
Beeps stopped causing hangs after this.
Linux's initial view of webcam:
[ 2.252040] usb 2-4: new high-speed USB device number 3 using ehci_hcd
[ 2.612801] usb 2-4: New USB device found, idVendor=046d, idProduct=0825
[ 2.612811] usb 2-4: New USB device strings: Mfr=0, Product=0,
SerialNumber=2
[ 2.612814] usb 2-4: SerialNumber: 2F31AED0
[ 3.184687] input: UVC Camera (046d:0825) as
/devices/pci0000:00/0000:00:1d.7/usb2/2-4/2-4:1.0/input/input4
[ 3.184762] usbcore: registered new interface driver uvcvideo
[ 3.184764] USB Video Class driver (1.1.1)
Logitech model number is C270 HD.
It's been a while since I actually attempted to use this webcam but it seemed
to be OK under squeeze's kernel.
ttfn/rjk
-- Package-specific info:
** Version:
Linux version 3.2.0-4-amd64 (debian-kernel@lists.debian.org) (gcc version 4.6.3 (Debian 4.6.3-15) ) #1 SMP Debian 3.2.41-2
** Command line:
BOOT_IMAGE=/vmlinuz-3.2.0-4-amd64 root=/dev/mapper/amfast-root ro quiet
** Tainted: PO (4097)
* Proprietary module has been loaded.
* Out-of-tree module has been loaded.
** Kernel log:
[174087.036164] 3:3:4: cannot set freq 48000 to ep 0x86
[174088.036144] 3:3:4: cannot set freq 48000 to ep 0x86
[174089.036118] 3:3:4: cannot set freq 48000 to ep 0x86
[174090.036097] 3:3:4: cannot set freq 48000 to ep 0x86
[174091.036078] 3:3:4: cannot set freq 48000 to ep 0x86
[174092.060181] 3:3:4: cannot set freq 48000 to ep 0x86
[174093.060161] 3:3:4: cannot set freq 48000 to ep 0x86
[174094.060137] 3:3:4: cannot set freq 48000 to ep 0x86
[174095.060121] 3:3:4: cannot set freq 48000 to ep 0x86
[174096.060097] 3:3:4: cannot set freq 48000 to ep 0x86
[174097.060077] 3:3:4: cannot set freq 48000 to ep 0x86
[174098.060055] 3:3:4: cannot set freq 48000 to ep 0x86
[174099.060161] 3:3:4: cannot set freq 48000 to ep 0x86
[174100.060138] 3:3:4: cannot set freq 48000 to ep 0x86
[174101.060115] 3:3:4: cannot set freq 48000 to ep 0x86
[174102.065213] 3:3:4: cannot set freq 48000 to ep 0x86
[174103.064075] 3:3:4: cannot set freq 48000 to ep 0x86
[174104.064052] 3:3:4: cannot set freq 48000 to ep 0x86
[174105.064157] 3:3:4: cannot set freq 48000 to ep 0x86
[174106.064133] 3:3:4: cannot set freq 48000 to ep 0x86
[174107.064108] 3:3:4: cannot set freq 48000 to ep 0x86
[174108.064091] 3:3:4: cannot set freq 48000 to ep 0x86
[174109.064070] 3:3:4: cannot set freq 48000 to ep 0x86
[174110.064172] 3:3:4: cannot set freq 48000 to ep 0x86
[174111.064153] 3:3:4: cannot set freq 48000 to ep 0x86
[174112.088132] 3:3:4: cannot set freq 48000 to ep 0x86
[174113.088108] 3:3:4: cannot set freq 48000 to ep 0x86
[174114.088088] 3:3:4: cannot set freq 48000 to ep 0x86
[174115.088068] 3:3:4: cannot set freq 48000 to ep 0x86
[174116.088171] 3:3:4: cannot set freq 48000 to ep 0x86
[174117.088150] 3:3:4: cannot set freq 48000 to ep 0x86
[174118.088128] 3:3:4: cannot set freq 48000 to ep 0x86
[174119.088106] 3:3:4: cannot set freq 48000 to ep 0x86
[174120.088086] 3:3:4: cannot set freq 48000 to ep 0x86
[174121.088065] 3:3:4: cannot set freq 48000 to ep 0x86
[174122.088168] 3:3:4: cannot set freq 48000 to ep 0x86
[174123.088147] 3:3:4: cannot set freq 48000 to ep 0x86
[174124.088125] 3:3:4: cannot set freq 48000 to ep 0x86
[174125.088106] 3:3:4: cannot set freq 48000 to ep 0x86
[174126.088084] 3:3:4: cannot set freq 48000 to ep 0x86
[174127.088064] 3:3:4: cannot set freq 48000 to ep 0x86
[174128.088167] 3:3:4: cannot set freq 48000 to ep 0x86
[174129.088146] 3:3:4: cannot set freq 48000 to ep 0x86
[174130.088123] 3:3:4: cannot set freq 48000 to ep 0x86
[174131.088103] 3:3:4: cannot set freq 48000 to ep 0x86
[174132.116079] 3:3:4: cannot set freq 48000 to ep 0x86
[174133.116059] 3:3:4: cannot set freq 48000 to ep 0x86
[174134.116161] 3:3:4: cannot set freq 48000 to ep 0x86
[174135.116143] 3:3:4: cannot set freq 48000 to ep 0x86
[174136.116120] 3:3:4: cannot set freq 48000 to ep 0x86
[174137.116099] 3:3:4: cannot set freq 48000 to ep 0x86
[174138.116079] 3:3:4: cannot set freq 48000 to ep 0x86
[174139.116058] 3:3:4: cannot set freq 48000 to ep 0x86
[174140.116160] 3:3:4: cannot set freq 48000 to ep 0x86
[174141.116137] 3:3:4: cannot set freq 48000 to ep 0x86
[174142.116115] 3:3:4: cannot set freq 48000 to ep 0x86
[174143.116097] 3:3:4: cannot set freq 48000 to ep 0x86
[174144.116326] 3:3:4: cannot set freq 48000 to ep 0x86
[174145.116053] 3:3:4: cannot set freq 48000 to ep 0x86
[174146.116158] 3:3:4: cannot set freq 48000 to ep 0x86
[174147.116136] 3:3:4: cannot set freq 48000 to ep 0x86
[174148.116113] 3:3:4: cannot set freq 48000 to ep 0x86
[174149.116092] 3:3:4: cannot set freq 48000 to ep 0x86
[174150.116073] 3:3:4: cannot set freq 48000 to ep 0x86
[174151.116053] 3:3:4: cannot set freq 48000 to ep 0x86
[174152.144155] 3:3:4: cannot set freq 48000 to ep 0x86
[174153.144133] 3:3:4: cannot set freq 48000 to ep 0x86
[174154.144112] 3:3:4: cannot set freq 48000 to ep 0x86
[174155.144093] 3:3:4: cannot set freq 48000 to ep 0x86
[174156.144070] 3:3:4: cannot set freq 48000 to ep 0x86
[174157.144048] 3:3:4: cannot set freq 48000 to ep 0x86
[174158.144151] 3:3:4: cannot set freq 48000 to ep 0x86
[174159.144132] 3:3:4: cannot set freq 48000 to ep 0x86
[174160.144108] 3:3:4: cannot set freq 48000 to ep 0x86
[174161.144089] 3:3:4: cannot set freq 48000 to ep 0x86
[174162.144068] 3:3:4: cannot set freq 48000 to ep 0x86
[174163.144045] 3:3:4: cannot set freq 48000 to ep 0x86
[174163.883550] usb 2-4: USB disconnect, device number 3
[174163.887534] 3:3:4: cannot set freq 48000 to ep 0x86
[174163.888054] 3:3:4: cannot set freq 48000 to ep 0x86
[174163.888438] 3:3:4: cannot set freq 48000 to ep 0x86
[174163.889238] 3:3:4: usb_set_interface failed
[174163.889289] 3:3:4: usb_set_interface failed
[174163.889424] 3:3:4: usb_set_interface failed
[174163.889745] 3:3:4: usb_set_interface failed
[174163.890100] 3:3:4: usb_set_interface failed
[174163.917697] 3:3:4: usb_set_interface failed
[174163.917722] 3:3:4: usb_set_interface failed
[174163.917758] 3:3:4: usb_set_interface failed
[174163.918032] 3:3:4: usb_set_interface failed
[174163.918309] 3:3:4: usb_set_interface failed
[174163.918621] 3:3:4: usb_set_interface failed
[174163.918644] 3:3:4: usb_set_interface failed
[174163.918680] 3:3:4: usb_set_interface failed
[174163.918914] 3:3:4: usb_set_interface failed
[174163.919182] 3:3:4: usb_set_interface failed
[174163.919633] 3:3:4: usb_set_interface failed
[174163.919681] 3:3:4: usb_set_interface failed
[174163.919809] 3:3:4: usb_set_interface failed
[174163.920155] 3:3:4: usb_set_interface failed
** Model information
sys_vendor:
product_name:
product_version:
chassis_vendor:
chassis_version:
bios_vendor: Intel Corp.
bios_version: MQ96510J.86A.0816.2006.0716.2308
board_vendor: Intel Corporation
board_name: DG965SS
board_version: AAD41678-304
** Loaded modules:
dm_snapshot
sha256_generic
cryptd
aes_x86_64
aes_generic
cbc
ip6table_filter
ip6_tables
iptable_filter
ip_tables
ebtable_nat
ebtables
x_tables
ppdev
lp
bnep
rfcomm
bluetooth
rfkill
cpufreq_stats
cpufreq_conservative
cpufreq_userspace
cpufreq_powersave
tun
binfmt_misc
nfsd
nfs
nfs_acl
auth_rpcgss
fscache
lockd
sunrpc
bridge
stp
ext3
jbd
dm_crypt
cpuid
msr
firewire_sbp2
loop
pl2303
usbserial
kvm_intel
kvm
nvidia(P)
usbhid
hid
snd_hda_codec_idt
snd_hda_intel
snd_hda_codec
uvcvideo
videodev
cdc_acm
snd_usb_audio
v4l2_compat_ioctl32
media
snd_usbmidi_lib
snd_hwdep
snd_pcm_oss
snd_mixer_oss
snd_pcm
snd_page_alloc
snd_seq_midi
snd_seq_midi_event
snd_rawmidi
snd_seq
evdev
snd_seq_device
snd_timer
snd
psmouse
coretemp
serio_raw
pcspkr
iTCO_wdt
i2c_i801
iTCO_vendor_support
soundcore
i2c_core
parport_pc
acpi_cpufreq
parport
mperf
button
processor
thermal_sys
ext4
crc16
jbd2
mbcache
dm_mod
md_mod
usb_storage
sg
sd_mod
sr_mod
cdrom
crc_t10dif
ata_generic
uhci_hcd
pata_marvell
firewire_ohci
firewire_core
crc_itu_t
ahci
libahci
ehci_hcd
libata
scsi_mod
usbcore
usb_common
e1000e
** Network interface configuration:
auto lo
iface lo inet loopback
auto br0
iface br0 inet static
network 172.17.207.0
address 172.17.207.18
netmask 255.255.255.0
broadcast 172.17.207.255
gateway 172.17.207.1
bridge_ports eth0
bridge_maxwait 2
iface br0 inet6 static
address 2001:470:1f09:11ed::12
gateway 2001:470:1f09:11ed::1
netmask 64
auto br0:0
iface br0:0 inet static
address 172.31.1.3
netmask 255.255.255.240
broadcast 172.31.1.15
** Network status:
*** IP interfaces and addresses:
1: lo: <LOOPBACK,UP,LOWER_UP> mtu 16436 qdisc noqueue state UNKNOWN
link/loopback 00:00:00:00:00:00 brd 00:00:00:00:00:00
inet 127.0.0.1/8 scope host lo
inet6 ::1/128 scope host
valid_lft forever preferred_lft forever
2: eth0: <BROADCAST,MULTICAST,UP,LOWER_UP> mtu 1500 qdisc pfifo_fast master br0 state UP qlen 1000
link/ether 00:19:d1:04:d1:76 brd ff:ff:ff:ff:ff:ff
3: br0: <BROADCAST,MULTICAST,UP,LOWER_UP> mtu 1500 qdisc noqueue state UP
link/ether 00:19:d1:04:d1:76 brd ff:ff:ff:ff:ff:ff
inet 172.17.207.18/24 brd 172.17.207.255 scope global br0
inet6 2001:470:1f09:11ed::12/64 scope global
valid_lft forever preferred_lft forever
inet6 fe80::219:d1ff:fe04:d176/64 scope link
valid_lft forever preferred_lft forever
7: vnet0: <BROADCAST,MULTICAST,UP,LOWER_UP> mtu 1500 qdisc pfifo_fast master br0 state UNKNOWN qlen 500
link/ether fe:52:00:42:60:3c brd ff:ff:ff:ff:ff:ff
inet6 fe80::fc52:ff:fe42:603c/64 scope link
valid_lft forever preferred_lft forever
*** Device statistics:
Inter-| Receive | Transmit
face |bytes packets errs drop fifo frame compressed multicast|bytes packets errs drop fifo colls carrier compressed
vnet0: 23028866 208374 0 0 0 0 0 0 779592710 338518 0 0 0 0 0 0
lo: 3390597671 2646179 0 0 0 0 0 0 3390597671 2646179 0 0 0 0 0 0
br0: 3837489747 4218799 0 0 0 0 0 0 3465344682 3334042 0 0 0 0 0 0
eth0: 4192655012 5192449 0 0 0 0 0 38305 3022106246 4730890 0 0 0 0 0 0
*** Protocol statistics:
Ip:
4301744 total packets received
0 forwarded
0 incoming packets discarded
4301093 incoming packets delivered
3472435 requests sent out
6 outgoing packets dropped
90 reassemblies required
42 packets reassembled ok
Icmp:
813 ICMP messages received
288 input ICMP message failed.
ICMP input histogram:
destination unreachable: 789
timeout in transit: 22
echo requests: 2
659 ICMP messages sent
0 ICMP messages failed
ICMP output histogram:
destination unreachable: 657
echo replies: 2
IcmpMsg:
InType3: 789
InType8: 2
InType11: 22
OutType0: 2
OutType3: 657
Tcp:
2042 active connections openings
1357 passive connection openings
279 failed connection attempts
383 connection resets received
27 connections established
6755415 segments received
7693386 segments send out
655 segments retransmited
1 bad segments received.
421 resets sent
Udp:
45964 packets received
224 packets to unknown port received.
0 packet receive errors
40009 packets sent
UdpLite:
TcpExt:
28 invalid SYN cookies received
48 packets pruned from receive queue because of socket buffer overrun
1703 TCP sockets finished time wait in fast timer
153265 delayed acks sent
68 delayed acks further delayed because of locked socket
Quick ack mode was activated 56 times
31706 packets directly queued to recvmsg prequeue.
781459 bytes directly in process context from backlog
119518157 bytes directly received in process context from prequeue
4778346 packet headers predicted
26380 packets header predicted and directly queued to user
408321 acknowledgments not containing data payload received
1980822 predicted acknowledgments
11 times recovered from packet loss by selective acknowledgements
1 congestion windows recovered without slow start by DSACK
44 congestion windows recovered without slow start after partial ack
10 TCP data loss events
4 timeouts after SACK recovery
12 fast retransmits
11 forward retransmits
4 retransmits in slow start
356 other TCP timeouts
3325 packets collapsed in receive queue due to low socket buffer
56 DSACKs sent for old packets
49 DSACKs received
39 connections reset due to unexpected data
312 connections reset due to early user close
3 connections aborted due to timeout
TCPDSACKIgnoredNoUndo: 20
TCPSackShifted: 40
TCPSackMerged: 6
TCPSackShiftFallback: 181
TCPBacklogDrop: 109
TCPDeferAcceptDrop: 28
TCPChallengeACK: 2
TCPSYNChallenge: 1
IpExt:
InMcastPkts: 6355
OutMcastPkts: 4277
InBcastPkts: 15949
OutBcastPkts: 2915
InOctets: -58860671
OutOctets: -796227009
InMcastOctets: 366681
OutMcastOctets: 145105
InBcastOctets: 1541388
OutBcastOctets: 339342
** PCI devices:
00:00.0 Host bridge [0600]: Intel Corporation 82P965/G965 Memory Controller Hub [8086:29a0] (rev 02)
Subsystem: Intel Corporation Device [8086:514d]
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort+ >SERR- <PERR- INTx-
Latency: 0
Capabilities: <access denied>
00:01.0 PCI bridge [0604]: Intel Corporation 82P965/G965 PCI Express Root Port [8086:29a1] (rev 02) (prog-if 00 [Normal decode])
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx+
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0, Cache Line Size: 64 bytes
Bus: primary=00, secondary=01, subordinate=01, sec-latency=0
Memory behind bridge: e0000000-e1ffffff
Prefetchable memory behind bridge: 00000000d0000000-00000000dfffffff
Secondary status: 66MHz- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort+ <SERR- <PERR-
BridgeCtl: Parity- SERR- NoISA- VGA+ MAbort- >Reset- FastB2B-
PriDiscTmr- SecDiscTmr- DiscTmrStat- DiscTmrSERREn-
Capabilities: <access denied>
Kernel driver in use: pcieport
00:03.0 Communication controller [0780]: Intel Corporation 82P965/G965 HECI Controller [8086:29a4] (rev 02)
Subsystem: Intel Corporation Device [8086:514d]
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0
Interrupt: pin A routed to IRQ 11
Region 0: Memory at e2226100 (64-bit, non-prefetchable) [size=16]
Capabilities: <access denied>
00:19.0 Ethernet controller [0200]: Intel Corporation 82566DC Gigabit Network Connection [8086:104b] (rev 02)
Subsystem: Intel Corporation Device [8086:0001]
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx+
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0
Interrupt: pin A routed to IRQ 46
Region 0: Memory at e2200000 (32-bit, non-prefetchable) [size=128K]
Region 1: Memory at e2224000 (32-bit, non-prefetchable) [size=4K]
Region 2: I/O ports at 20e0 [size=32]
Capabilities: <access denied>
Kernel driver in use: e1000e
00:1a.0 USB controller [0c03]: Intel Corporation 82801H (ICH8 Family) USB UHCI Controller #4 [8086:2834] (rev 02) (prog-if 00 [UHCI])
Subsystem: Intel Corporation Device [8086:514d]
Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap- 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0
Interrupt: pin A routed to IRQ 16
Region 4: I/O ports at 20c0 [size=32]
Kernel driver in use: uhci_hcd
00:1a.1 USB controller [0c03]: Intel Corporation 82801H (ICH8 Family) USB UHCI Controller #5 [8086:2835] (rev 02) (prog-if 00 [UHCI])
Subsystem: Intel Corporation Device [8086:514d]
Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap- 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0
Interrupt: pin B routed to IRQ 21
Region 4: I/O ports at 20a0 [size=32]
Kernel driver in use: uhci_hcd
00:1a.7 USB controller [0c03]: Intel Corporation 82801H (ICH8 Family) USB2 EHCI Controller #2 [8086:283a] (rev 02) (prog-if 20 [EHCI])
Subsystem: Intel Corporation Device [8086:514d]
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0
Interrupt: pin C routed to IRQ 18
Region 0: Memory at e2225c00 (32-bit, non-prefetchable) [size=1K]
Capabilities: <access denied>
Kernel driver in use: ehci_hcd
00:1b.0 Audio device [0403]: Intel Corporation 82801H (ICH8 Family) HD Audio Controller [8086:284b] (rev 02)
Subsystem: Intel Corporation Device [8086:2114]
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx+
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0, Cache Line Size: 64 bytes
Interrupt: pin A routed to IRQ 48
Region 0: Memory at e2220000 (64-bit, non-prefetchable) [size=16K]
Capabilities: <access denied>
Kernel driver in use: snd_hda_intel
00:1c.0 PCI bridge [0604]: Intel Corporation 82801H (ICH8 Family) PCI Express Port 1 [8086:283f] (rev 02) (prog-if 00 [Normal decode])
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx+
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0, Cache Line Size: 64 bytes
Bus: primary=00, secondary=02, subordinate=02, sec-latency=0
I/O behind bridge: 00006000-00006fff
Memory behind bridge: e2300000-e23fffff
Prefetchable memory behind bridge: 00000000e2f00000-00000000e30fffff
Secondary status: 66MHz- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- <SERR- <PERR-
BridgeCtl: Parity- SERR- NoISA+ VGA- MAbort- >Reset- FastB2B-
PriDiscTmr- SecDiscTmr- DiscTmrStat- DiscTmrSERREn-
Capabilities: <access denied>
Kernel driver in use: pcieport
00:1c.1 PCI bridge [0604]: Intel Corporation 82801H (ICH8 Family) PCI Express Port 2 [8086:2841] (rev 02) (prog-if 00 [Normal decode])
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx+
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0, Cache Line Size: 64 bytes
Bus: primary=00, secondary=03, subordinate=03, sec-latency=0
I/O behind bridge: 00001000-00001fff
Memory behind bridge: e2100000-e21fffff
Prefetchable memory behind bridge: 00000000e2d00000-00000000e2efffff
Secondary status: 66MHz- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- <SERR- <PERR-
BridgeCtl: Parity- SERR- NoISA+ VGA- MAbort- >Reset- FastB2B-
PriDiscTmr- SecDiscTmr- DiscTmrStat- DiscTmrSERREn-
Capabilities: <access denied>
Kernel driver in use: pcieport
00:1c.2 PCI bridge [0604]: Intel Corporation 82801H (ICH8 Family) PCI Express Port 3 [8086:2843] (rev 02) (prog-if 00 [Normal decode])
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx+
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0, Cache Line Size: 64 bytes
Bus: primary=00, secondary=04, subordinate=04, sec-latency=0
I/O behind bridge: 00005000-00005fff
Memory behind bridge: e2400000-e24fffff
Prefetchable memory behind bridge: 00000000e2b00000-00000000e2cfffff
Secondary status: 66MHz- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- <SERR- <PERR-
BridgeCtl: Parity- SERR- NoISA+ VGA- MAbort- >Reset- FastB2B-
PriDiscTmr- SecDiscTmr- DiscTmrStat- DiscTmrSERREn-
Capabilities: <access denied>
Kernel driver in use: pcieport
00:1c.3 PCI bridge [0604]: Intel Corporation 82801H (ICH8 Family) PCI Express Port 4 [8086:2845] (rev 02) (prog-if 00 [Normal decode])
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx+
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0, Cache Line Size: 64 bytes
Bus: primary=00, secondary=05, subordinate=05, sec-latency=0
I/O behind bridge: 00004000-00004fff
Memory behind bridge: e2500000-e25fffff
Prefetchable memory behind bridge: 00000000e2900000-00000000e2afffff
Secondary status: 66MHz- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- <SERR- <PERR-
BridgeCtl: Parity- SERR- NoISA+ VGA- MAbort- >Reset- FastB2B-
PriDiscTmr- SecDiscTmr- DiscTmrStat- DiscTmrSERREn-
Capabilities: <access denied>
Kernel driver in use: pcieport
00:1c.4 PCI bridge [0604]: Intel Corporation 82801H (ICH8 Family) PCI Express Port 5 [8086:2847] (rev 02) (prog-if 00 [Normal decode])
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx+
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0, Cache Line Size: 64 bytes
Bus: primary=00, secondary=06, subordinate=06, sec-latency=0
I/O behind bridge: 00003000-00003fff
Memory behind bridge: e2600000-e26fffff
Prefetchable memory behind bridge: 00000000e2700000-00000000e28fffff
Secondary status: 66MHz- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- <SERR- <PERR-
BridgeCtl: Parity- SERR- NoISA+ VGA- MAbort- >Reset- FastB2B-
PriDiscTmr- SecDiscTmr- DiscTmrStat- DiscTmrSERREn-
Capabilities: <access denied>
Kernel driver in use: pcieport
00:1d.0 USB controller [0c03]: Intel Corporation 82801H (ICH8 Family) USB UHCI Controller #1 [8086:2830] (rev 02) (prog-if 00 [UHCI])
Subsystem: Intel Corporation Device [8086:514d]
Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap- 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0
Interrupt: pin A routed to IRQ 23
Region 4: I/O ports at 2080 [size=32]
Kernel driver in use: uhci_hcd
00:1d.1 USB controller [0c03]: Intel Corporation 82801H (ICH8 Family) USB UHCI Controller #2 [8086:2831] (rev 02) (prog-if 00 [UHCI])
Subsystem: Intel Corporation Device [8086:514d]
Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap- 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0
Interrupt: pin B routed to IRQ 19
Region 4: I/O ports at 2060 [size=32]
Kernel driver in use: uhci_hcd
00:1d.2 USB controller [0c03]: Intel Corporation 82801H (ICH8 Family) USB UHCI Controller #3 [8086:2832] (rev 02) (prog-if 00 [UHCI])
Subsystem: Intel Corporation Device [8086:514d]
Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap- 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0
Interrupt: pin C routed to IRQ 18
Region 4: I/O ports at 2040 [size=32]
Kernel driver in use: uhci_hcd
00:1d.7 USB controller [0c03]: Intel Corporation 82801H (ICH8 Family) USB2 EHCI Controller #1 [8086:2836] (rev 02) (prog-if 20 [EHCI])
Subsystem: Intel Corporation Device [8086:514d]
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0
Interrupt: pin A routed to IRQ 23
Region 0: Memory at e2225800 (32-bit, non-prefetchable) [size=1K]
Capabilities: <access denied>
Kernel driver in use: ehci_hcd
00:1e.0 PCI bridge [0604]: Intel Corporation 82801 PCI Bridge [8086:244e] (rev f2) (prog-if 01 [Subtractive decode])
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0
Bus: primary=00, secondary=07, subordinate=07, sec-latency=32
Memory behind bridge: e2000000-e20fffff
Secondary status: 66MHz- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort+ <SERR- <PERR-
BridgeCtl: Parity- SERR- NoISA+ VGA- MAbort- >Reset- FastB2B-
PriDiscTmr- SecDiscTmr- DiscTmrStat- DiscTmrSERREn-
Capabilities: <access denied>
00:1f.0 ISA bridge [0601]: Intel Corporation 82801HB/HR (ICH8/R) LPC Interface Controller [8086:2810] (rev 02)
Subsystem: Intel Corporation Device [8086:514d]
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0
Capabilities: <access denied>
00:1f.2 SATA controller [0106]: Intel Corporation 82801HB (ICH8) 4 port SATA Controller [AHCI mode] [8086:2824] (rev 02) (prog-if 01 [AHCI 1.0])
Subsystem: Intel Corporation Device [8086:514d]
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx+
Status: Cap+ 66MHz+ UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0
Interrupt: pin A routed to IRQ 47
Region 0: I/O ports at 2108 [size=8]
Region 1: I/O ports at 2114 [size=4]
Region 2: I/O ports at 2100 [size=8]
Region 3: I/O ports at 2110 [size=4]
Region 4: I/O ports at 2020 [size=32]
Region 5: Memory at e2225000 (32-bit, non-prefetchable) [size=2K]
Capabilities: <access denied>
Kernel driver in use: ahci
00:1f.3 SMBus [0c05]: Intel Corporation 82801H (ICH8 Family) SMBus Controller [8086:283e] (rev 02)
Subsystem: Intel Corporation Device [8086:514d]
Control: I/O+ Mem+ BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap- 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Interrupt: pin B routed to IRQ 21
Region 0: Memory at e2226000 (32-bit, non-prefetchable) [size=256]
Region 4: I/O ports at 2000 [size=32]
Kernel driver in use: i801_smbus
01:00.0 VGA compatible controller [0300]: NVIDIA Corporation G71 [GeForce 7300 GS] [10de:01df] (rev a1) (prog-if 00 [VGA controller])
Subsystem: Micro-Star International Co., Ltd. Device [1462:0345]
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0
Interrupt: pin A routed to IRQ 16
Region 0: Memory at e1000000 (32-bit, non-prefetchable) [size=16M]
Region 1: Memory at d0000000 (64-bit, prefetchable) [size=256M]
Region 3: Memory at e0000000 (64-bit, non-prefetchable) [size=16M]
Expansion ROM at <unassigned> [disabled]
Capabilities: <access denied>
Kernel driver in use: nvidia
03:00.0 IDE interface [0101]: Marvell Technology Group Ltd. 88SE6101/6102 single-port PATA133 interface [11ab:6101] (rev b1) (prog-if 8f [Master SecP SecO PriP PriO])
Subsystem: Marvell Technology Group Ltd. 88SE6101/6102 single-port PATA133 interface [11ab:6101]
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0, Cache Line Size: 64 bytes
Interrupt: pin A routed to IRQ 17
Region 0: I/O ports at 1018 [size=8]
Region 1: I/O ports at 1024 [size=4]
Region 2: I/O ports at 1010 [size=8]
Region 3: I/O ports at 1020 [size=4]
Region 4: I/O ports at 1000 [size=16]
Region 5: Memory at e2100000 (32-bit, non-prefetchable) [size=512]
Capabilities: <access denied>
Kernel driver in use: pata_marvell
07:03.0 FireWire (IEEE 1394) [0c00]: Texas Instruments TSB43AB22A IEEE-1394a-2000 Controller (PHY/Link) [iOHCI-Lynx] [104c:8023] (prog-if 10 [OHCI])
Subsystem: Intel Corporation Device [8086:514d]
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV+ VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 32 (500ns min, 1000ns max), Cache Line Size: 64 bytes
Interrupt: pin A routed to IRQ 19
Region 0: Memory at e2004000 (32-bit, non-prefetchable) [size=2K]
Region 1: Memory at e2000000 (32-bit, non-prefetchable) [size=16K]
Capabilities: <access denied>
Kernel driver in use: firewire_ohci
** USB devices:
Bus 001 Device 001: ID 1d6b:0002 Linux Foundation 2.0 root hub
Bus 002 Device 001: ID 1d6b:0002 Linux Foundation 2.0 root hub
Bus 003 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub
Bus 004 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub
Bus 005 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub
Bus 006 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub
Bus 007 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub
Bus 001 Device 003: ID 1058:1003 Western Digital Technologies, Inc. Elements 1000 GB
Bus 002 Device 002: ID 0409:0059 NEC Corp. HighSpeed Hub
Bus 004 Device 002: ID 20df:0001 Simtec Electronics Entropy Key [UDEKEY01]
Bus 002 Device 004: ID 04d9:2221 Holtek Semiconductor, Inc. Keyboard
Bus 002 Device 005: ID 047d:1020 Kensington Expert Mouse Trackball
Bus 002 Device 006: ID 067b:2303 Prolific Technology, Inc. PL2303 Serial Port
Bus 002 Device 007: ID 0d49:7410 Maxtor Mobile Hard Disk Drive (1TB)
Bus 001 Device 005: ID 1058:0701 Western Digital Technologies, Inc.
-- System Information:
Debian Release: 7.0
APT prefers stable
APT policy: (990, 'stable'), (500, 'stable-updates')
Architecture: amd64 (x86_64)
Kernel: Linux 3.2.0-4-amd64 (SMP w/4 CPU cores)
Locale: LANG=en_GB.UTF-8, LC_CTYPE=en_GB.UTF-8 (charmap=UTF-8)
Shell: /bin/sh linked to /bin/bash
Versions of packages linux-image-3.2.0-4-amd64 depends on:
ii debconf [debconf-2.0] 1.5.49
ii initramfs-tools [linux-initramfs-tool] 0.109.1
ii kmod 9-3
ii linux-base 3.5
ii module-init-tools 9-3
Versions of packages linux-image-3.2.0-4-amd64 recommends:
ii firmware-linux-free 3.2
Versions of packages linux-image-3.2.0-4-amd64 suggests:
pn debian-kernel-handbook <none>
ii grub-pc 1.99-27+deb7u1
ii linux-doc-3.2 3.2.41-2
Versions of packages linux-image-3.2.0-4-amd64 is related to:
ii firmware-atheros 0.36+wheezy.1
ii firmware-bnx2 0.36+wheezy.1
ii firmware-bnx2x 0.36+wheezy.1
ii firmware-brcm80211 0.36+wheezy.1
ii firmware-intelwimax 0.36+wheezy.1
ii firmware-ipw2x00 0.36+wheezy.1
ii firmware-ivtv 0.36+wheezy.1
ii firmware-iwlwifi 0.36+wheezy.1
ii firmware-libertas 0.36+wheezy.1
ii firmware-linux 0.36+wheezy.1
ii firmware-linux-nonfree 0.36+wheezy.1
pn firmware-myricom <none>
ii firmware-netxen 0.36+wheezy.1
ii firmware-qlogic 0.36+wheezy.1
ii firmware-ralink 0.36+wheezy.1
ii firmware-realtek 0.36+wheezy.1
pn xen-hypervisor <none>
-- debconf information:
linux-image-3.2.0-4-amd64/postinst/depmod-error-initrd-3.2.0-4-amd64: false
linux-image-3.2.0-4-amd64/prerm/removing-running-kernel-3.2.0-4-amd64: true
linux-image-3.2.0-4-amd64/postinst/ignoring-ramdisk:
linux-image-3.2.0-4-amd64/postinst/missing-firmware-3.2.0-4-amd64:
Reply to: