Bug#677016: linux-image-3.3.0-trunk-amd64: Freeze with error message upon resume
Package: linux-2.6
Version: 3.3.6-1~experimental.1
Severity: important
Dear Maintainer,
Very often (each 2-10 times) kernel freezes with an error message upon
resuming from suspend to ram. Here is the message:
kobject_add_internal failed for BATO with -EEXIST, don't try to
register things with the same name in the same directory
3.2 version of the kernel freezes at suspend too, but as far as I
noticed with another error message, something like infinite
recursion. I can get it if needed.
3.1 freezes too.
In fact, I have been having freezes at suspend since 3.0 or 2.6.39,
while before suspend was working perfectly.
Thank you,
Eugen Dedu
http://eugen.dedu.free.fr
-- Package-specific info:
** Version:
Linux version 3.3.0-trunk-amd64 (Debian 3.3.6-1~experimental.1)
(debian-kernel@lists.debian.org) (gcc version 4.6.3 (Debian 4.6.3-1) )
#1 SMP Fri May 18 14:52:13 UTC 2012
** Command line:
BOOT_IMAGE=/boot/vmlinuz-3.3.0-trunk-amd64
root=UUID=0efdb302-9d8b-4eeb-9102-f18c3fa8d2f0 ro quiet
** Tainted: O (4096)
* Out-of-tree module has been loaded.
** Kernel log:
[ 5.181589] input: HDA Intel Mic as
/devices/pci0000:00/0000:00:1b.0/sound/card0/input13
[ 5.181658] input: HDA Intel Headphone as
/devices/pci0000:00/0000:00:1b.0/sound/card0/input14
[ 5.181726] input: HDA Intel Dock Line Out as
/devices/pci0000:00/0000:00:1b.0/sound/card0/input15
[ 5.328972] usb 3-1: New USB device found, idVendor=0a5c, idProduct=4500
[ 5.328977] usb 3-1: New USB device strings: Mfr=1, Product=2,
SerialNumber=0
[ 5.328980] usb 3-1: Product: BCM2046B1
[ 5.328983] usb 3-1: Manufacturer: Broadcom
[ 5.332042] hub 3-1:1.0: USB hub found
[ 5.333963] hub 3-1:1.0: 3 ports detected
[ 5.399113] dell_wmi: Received unknown WMI event (0x11)
[ 5.432910] EXT4-fs (sda1): re-mounted. Opts: (null)
[ 5.479747] EXT4-fs (sda1): re-mounted. Opts: errors=remount-ro
[ 5.516848] loop: module loaded
[ 5.576036] usb 5-1: new full-speed USB device number 2 using uhci_hcd
[ 5.755781] usb 5-1: New USB device found, idVendor=0a5c, idProduct=5800
[ 5.755784] usb 5-1: New USB device strings: Mfr=1, Product=2,
SerialNumber=3
[ 5.755786] usb 5-1: Product: 5880
[ 5.755788] usb 5-1: Manufacturer: Broadcom Corp
[ 5.755790] usb 5-1: SerialNumber: 0123456789ABCD
[ 5.755884] usb 5-1: config 0 descriptor??
[ 5.779928] WARNING! power/level is deprecated; use power/control instead
[ 6.008035] usb 6-2: new low-speed USB device number 2 using uhci_hcd
[ 6.181162] usb 6-2: New USB device found, idVendor=1c4f, idProduct=0003
[ 6.181166] usb 6-2: New USB device strings: Mfr=1, Product=2,
SerialNumber=0
[ 6.181168] usb 6-2: Product: Usb Mouse
[ 6.181170] usb 6-2: Manufacturer: SIGMACHIP
[ 6.214501] input: SIGMACHIP Usb Mouse as
/devices/pci0000:00/0000:00:1d.0/usb6/6-2/6-2:1.0/input/input16
[ 6.214955] generic-usb 0003:1C4F:0003.0001: input,hidraw0: USB HID
v1.10 Mouse [SIGMACHIP Usb Mouse] on usb-0000:00:1d.0-2/input0
[ 6.215191] usbcore: registered new interface driver usbhid
[ 6.215193] usbhid: USB HID core driver
[ 6.257976] usb 3-1.1: new full-speed USB device number 3 using uhci_hcd
[ 6.379983] usb 3-1.1: New USB device found, idVendor=413c,
idProduct=8157
[ 6.379987] usb 3-1.1: New USB device strings: Mfr=0, Product=0,
SerialNumber=0
[ 6.387223] input: HID 413c:8157 as
/devices/pci0000:00/0000:00:1a.0/usb3/3-1/3-1.1/3-1.1:1.0/input/input17
[ 6.387385] generic-usb 0003:413C:8157.0002: input,hidraw1: USB HID
v1.11 Keyboard [HID 413c:8157] on usb-0000:00:1a.0-1.1/input0
[ 6.461990] usb 3-1.2: new full-speed USB device number 4 using uhci_hcd
[ 6.586981] usb 3-1.2: New USB device found, idVendor=413c,
idProduct=8158
[ 6.586984] usb 3-1.2: New USB device strings: Mfr=0, Product=0,
SerialNumber=0
[ 6.595258] input: HID 413c:8158 as
/devices/pci0000:00/0000:00:1a.0/usb3/3-1/3-1.2/3-1.2:1.0/input/input18
[ 6.595376] generic-usb 0003:413C:8158.0003: input,hidraw2: USB HID
v1.11 Mouse [HID 413c:8158] on usb-0000:00:1a.0-1.2/input0
[ 6.721433] vboxdrv: Found 2 processor cores.
[ 6.722037] vboxdrv: fAsync=0 offMin=0x1ac offMax=0x5188
[ 6.722098] vboxdrv: TSC mode is 'synchronous', kernel timer mode is
'normal'.
[ 6.722100] vboxdrv: Successfully loaded version 4.1.16_Debian
(interface 0x00190000).
[ 6.786523] vboxpci: IOMMU not found (not registered)
[ 6.945982] usb 3-1.3: new full-speed USB device number 5 using uhci_hcd
[ 7.078974] usb 3-1.3: New USB device found, idVendor=413c,
idProduct=8156
[ 7.078979] usb 3-1.3: New USB device strings: Mfr=1, Product=2,
SerialNumber=0
[ 7.078982] usb 3-1.3: Product: Dell Wireless 370 Bluetooth Mini-card
[ 7.078985] usb 3-1.3: Manufacturer: Dell Computer Corp
[ 7.101675] Bluetooth: Core ver 2.16
[ 7.101700] NET: Registered protocol family 31
[ 7.101701] Bluetooth: HCI device and connection manager initialized
[ 7.101704] Bluetooth: HCI socket layer initialized
[ 7.101706] Bluetooth: L2CAP socket layer initialized
[ 7.101713] Bluetooth: SCO socket layer initialized
[ 7.106395] usbcore: registered new interface driver btusb
[ 7.139234] Bluetooth: BNEP (Ethernet Emulation) ver 1.3
[ 7.139237] Bluetooth: BNEP filters: protocol multicast
[ 7.216589] Bluetooth: RFCOMM TTY layer initialized
[ 7.216601] Bluetooth: RFCOMM socket layer initialized
[ 7.216607] Bluetooth: RFCOMM ver 1.11
[ 7.357288] lp: driver loaded but no devices found
[ 7.360132] ppdev: user-space parallel port driver
[ 7.670356] e1000e 0000:00:19.0: irq 45 for MSI/MSI-X
[ 7.685866] input: ACPI Virtual Keyboard Device as
/devices/virtual/input/input19
[ 7.724099] e1000e 0000:00:19.0: irq 45 for MSI/MSI-X
[ 7.724705] ADDRCONF(NETDEV_UP): eth0: link is not ready
[ 7.726823] iwlwifi 0000:0c:00.0: L1 Enabled; Disabling L0S
[ 7.729889] iwlwifi 0000:0c:00.0: Radio type=0x1-0x2-0x0
[ 7.845039] iwlwifi 0000:0c:00.0: L1 Enabled; Disabling L0S
[ 7.848028] iwlwifi 0000:0c:00.0: Radio type=0x1-0x2-0x0
[ 7.896583] ADDRCONF(NETDEV_UP): wlan0: link is not ready
[ 9.512951] e1000e: eth0 NIC Link is Up 100 Mbps Full Duplex, Flow
Control: None
[ 9.512963] e1000e 0000:00:19.0: eth0: 10/100 speed: disabling TSO
[ 9.514525] ADDRCONF(NETDEV_CHANGE): eth0: link becomes ready
[ 20.000032] eth0: no IPv6 routers present
[ 20.884125] wlan0: authenticate with 00:0b:86:a6:92:18 (try 1)
[ 20.896264] wlan0: authenticated
[ 20.911024] wlan0: associate with 00:0b:86:a6:92:18 (try 1)
[ 20.914720] wlan0: RX AssocResp from 00:0b:86:a6:92:18 (capab=0x431
status=0 aid=2)
[ 20.914724] wlan0: associated
[ 20.914729] wlan0: moving STA 00:0b:86:a6:92:18 to state 1
[ 20.914731] wlan0: moving STA 00:0b:86:a6:92:18 to state 2
[ 20.925329] ADDRCONF(NETDEV_CHANGE): wlan0: link becomes ready
[ 21.187003] Intel AES-NI instructions are not detected.
[ 21.228289] wlan0: moving STA 00:0b:86:a6:92:18 to state 3
[ 25.980357] usb 6-2: USB disconnect, device number 2
[ 28.240334] usb 6-2: new low-speed USB device number 3 using uhci_hcd
[ 28.412391] usb 6-2: New USB device found, idVendor=1c4f, idProduct=0003
[ 28.412401] usb 6-2: New USB device strings: Mfr=1, Product=2,
SerialNumber=0
[ 28.412408] usb 6-2: Product: Usb Mouse
[ 28.412413] usb 6-2: Manufacturer: SIGMACHIP
[ 28.428756] input: SIGMACHIP Usb Mouse as
/devices/pci0000:00/0000:00:1d.0/usb6/6-2/6-2:1.0/input/input20
[ 28.429127] generic-usb 0003:1C4F:0003.0004: input,hidraw0: USB HID
v1.10 Mouse [SIGMACHIP Usb Mouse] on usb-0000:00:1d.0-2/input0
[ 31.096039] wlan0: no IPv6 routers present
[ 37.848105] usb 3-1: USB disconnect, device number 2
[ 37.848114] usb 3-1.1: USB disconnect, device number 3
[ 37.868464] usb 3-1.2: USB disconnect, device number 4
[ 37.871960] usb 3-1.3: USB disconnect, device number 5
** Model information
sys_vendor: Dell Inc.
product_name: Latitude E6500
product_version:
chassis_vendor: Dell Inc.
chassis_version:
bios_vendor: Dell Inc.
bios_version: A19
board_vendor: Dell Inc.
board_name: 0W612R
board_version:
** Loaded modules:
cryptd
aes_x86_64
aes_generic
parport_pc
ppdev
lp
parport
rfcomm
bnep
btusb
bluetooth
acpi_cpufreq
mperf
cpufreq_conservative
cpufreq_stats
cpufreq_powersave
cpufreq_userspace
pci_stub
vboxpci(O)
vboxnetadp(O)
vboxnetflt(O)
vboxdrv(O)
uinput
usbhid
hid
loop
firewire_sbp2
snd_hda_codec_hdmi
snd_hda_codec_idt
joydev
uvcvideo
videobuf2_vmalloc
videobuf2_memops
videobuf2_core
videodev
v4l2_compat_ioctl32
media
pcmcia
snd_hda_intel
snd_hda_codec
snd_hwdep
snd_pcm_oss
snd_mixer_oss
snd_pcm
snd_page_alloc
arc4
snd_seq_midi
snd_seq_midi_event
snd_rawmidi
snd_seq
dell_wmi
sparse_keymap
snd_seq_device
snd_timer
iwlwifi
mac80211
i915
yenta_socket
firewire_ohci
sr_mod
drm_kms_helper
cfg80211
cdrom
evdev
pcmcia_rsrc
drm
snd
sdhci_pci
psmouse
firewire_core
dell_laptop
i2c_algo_bit
iTCO_wdt
sdhci
dcdbas
pcspkr
serio_raw
i2c_i801
rfkill
pcmcia_core
mmc_core
crc_itu_t
iTCO_vendor_support
uhci_hcd
ehci_hcd
soundcore
usbcore
i2c_core
e1000e
usb_common
video
wmi
battery
button
ac
power_supply
processor
ext4
crc16
jbd2
mbcache
sd_mod
crc_t10dif
thermal
thermal_sys
ahci
libahci
libata
scsi_mod
** PCI devices:
00:00.0 Host bridge [0600]: Intel Corporation Mobile 4 Series Chipset
Memory Controller Hub [8086:2a40] (rev 07)
Subsystem: Dell Device [1028:024f]
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=fast >TAbort- <TAbort-
<MAbort+ >SERR- <PERR- INTx-
Latency: 0
Capabilities: <access denied>
Kernel driver in use: agpgart-intel
00:02.0 VGA compatible controller [0300]: Intel Corporation Mobile 4
Series Chipset Integrated Graphics Controller [8086:2a42] (rev 07)
(prog-if 00 [VGA controller])
Subsystem: Dell Device [1028:024f]
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B- DisINTx+
Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=fast >TAbort- <TAbort-
<MAbort- >SERR- <PERR- INTx-
Latency: 0
Interrupt: pin A routed to IRQ 47
Region 0: Memory at f6c00000 (64-bit, non-prefetchable) [size=4M]
Region 2: Memory at e0000000 (64-bit, prefetchable) [size=256M]
Region 4: I/O ports at ef98 [size=8]
Expansion ROM at <unassigned> [disabled]
Capabilities: <access denied>
Kernel driver in use: i915
00:02.1 Display controller [0380]: Intel Corporation Mobile 4 Series
Chipset Integrated Graphics Controller [8086:2a43] (rev 07)
Subsystem: Dell Device [1028:024f]
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=fast >TAbort- <TAbort-
<MAbort- >SERR- <PERR- INTx-
Latency: 0
Region 0: Memory at f6b00000 (64-bit, non-prefetchable) [size=1M]
Capabilities: <access denied>
00:19.0 Ethernet controller [0200]: Intel Corporation 82567LM Gigabit
Network Connection [8086:10f5] (rev 03)
Subsystem: Dell Device [1028:024f]
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR+ FastB2B- DisINTx+
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort-
<MAbort- >SERR- <PERR- INTx-
Latency: 0
Interrupt: pin A routed to IRQ 45
Region 0: Memory at f6ae0000 (32-bit, non-prefetchable) [size=128K]
Region 1: Memory at f6adb000 (32-bit, non-prefetchable) [size=4K]
Region 2: I/O ports at efe0 [size=32]
Capabilities: <access denied>
Kernel driver in use: e1000e
00:1a.0 USB controller [0c03]: Intel Corporation 82801I (ICH9 Family)
USB UHCI Controller #4 [8086:2937] (rev 03) (prog-if 00 [UHCI])
Subsystem: Dell Device [1028:024f]
Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0
Interrupt: pin A routed to IRQ 20
Region 4: I/O ports at 6f60 [size=32]
Capabilities: <access denied>
Kernel driver in use: uhci_hcd
00:1a.1 USB controller [0c03]: Intel Corporation 82801I (ICH9 Family)
USB UHCI Controller #5 [8086:2938] (rev 03) (prog-if 00 [UHCI])
Subsystem: Dell Device [1028:024f]
Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0
Interrupt: pin B routed to IRQ 21
Region 4: I/O ports at 6f80 [size=32]
Capabilities: <access denied>
Kernel driver in use: uhci_hcd
00:1a.2 USB controller [0c03]: Intel Corporation 82801I (ICH9 Family)
USB UHCI Controller #6 [8086:2939] (rev 03) (prog-if 00 [UHCI])
Subsystem: Dell Device [1028:024f]
Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0
Interrupt: pin C routed to IRQ 22
Region 4: I/O ports at 6fa0 [size=32]
Capabilities: <access denied>
Kernel driver in use: uhci_hcd
00:1a.7 USB controller [0c03]: Intel Corporation 82801I (ICH9 Family)
USB2 EHCI Controller #2 [8086:293c] (rev 03) (prog-if 20 [EHCI])
Subsystem: Dell Device [1028:024f]
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR+ FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0
Interrupt: pin C routed to IRQ 22
Region 0: Memory at fed1c400 (32-bit, non-prefetchable) [size=1K]
Capabilities: <access denied>
Kernel driver in use: ehci_hcd
00:1b.0 Audio device [0403]: Intel Corporation 82801I (ICH9 Family) HD
Audio Controller [8086:293e] (rev 03)
Subsystem: Dell Device [1028:024f]
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR+ FastB2B- DisINTx+
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort-
<MAbort- >SERR- <PERR- INTx-
Latency: 0, Cache Line Size: 64 bytes
Interrupt: pin A routed to IRQ 48
Region 0: Memory at f6adc000 (64-bit, non-prefetchable) [size=16K]
Capabilities: <access denied>
Kernel driver in use: snd_hda_intel
00:1c.0 PCI bridge [0604]: Intel Corporation 82801I (ICH9 Family) PCI
Express Port 1 [8086:2940] (rev 03) (prog-if 00 [Normal decode])
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR+ FastB2B- DisINTx+
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort-
<MAbort- >SERR- <PERR- INTx-
Latency: 0, Cache Line Size: 64 bytes
Bus: primary=00, secondary=0b, subordinate=0b, sec-latency=0
I/O behind bridge: 00005000-00005fff
Memory behind bridge: f0800000-f09fffff
Prefetchable memory behind bridge: 00000000f0a00000-00000000f0bfffff
Secondary status: 66MHz- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort-
<MAbort- <SERR- <PERR-
BridgeCtl: Parity- SERR+ NoISA- VGA- MAbort- >Reset- FastB2B-
PriDiscTmr- SecDiscTmr- DiscTmrStat- DiscTmrSERREn-
Capabilities: <access denied>
Kernel driver in use: pcieport
00:1c.1 PCI bridge [0604]: Intel Corporation 82801I (ICH9 Family) PCI
Express Port 2 [8086:2942] (rev 03) (prog-if 00 [Normal decode])
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR+ FastB2B- DisINTx+
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort-
<MAbort- >SERR- <PERR- INTx-
Latency: 0, Cache Line Size: 64 bytes
Bus: primary=00, secondary=0c, subordinate=0c, sec-latency=0
I/O behind bridge: 00004000-00004fff
Memory behind bridge: f6900000-f69fffff
Prefetchable memory behind bridge: 00000000f0600000-00000000f07fffff
Secondary status: 66MHz- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort-
<MAbort- <SERR- <PERR-
BridgeCtl: Parity- SERR+ NoISA- VGA- MAbort- >Reset- FastB2B-
PriDiscTmr- SecDiscTmr- DiscTmrStat- DiscTmrSERREn-
Capabilities: <access denied>
Kernel driver in use: pcieport
00:1c.2 PCI bridge [0604]: Intel Corporation 82801I (ICH9 Family) PCI
Express Port 3 [8086:2944] (rev 03) (prog-if 00 [Normal decode])
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR+ FastB2B- DisINTx+
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort-
<MAbort- >SERR- <PERR- INTx-
Latency: 0, Cache Line Size: 64 bytes
Bus: primary=00, secondary=0d, subordinate=0d, sec-latency=0
I/O behind bridge: 00003000-00003fff
Memory behind bridge: f0200000-f03fffff
Prefetchable memory behind bridge: 00000000f0400000-00000000f05fffff
Secondary status: 66MHz- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort-
<MAbort- <SERR- <PERR-
BridgeCtl: Parity- SERR+ NoISA- VGA- MAbort- >Reset- FastB2B-
PriDiscTmr- SecDiscTmr- DiscTmrStat- DiscTmrSERREn-
Capabilities: <access denied>
Kernel driver in use: pcieport
00:1c.3 PCI bridge [0604]: Intel Corporation 82801I (ICH9 Family) PCI
Express Port 4 [8086:2946] (rev 03) (prog-if 00 [Normal decode])
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B- DisINTx+
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort-
<MAbort- >SERR- <PERR- INTx-
Latency: 0, Cache Line Size: 64 bytes
Bus: primary=00, secondary=0e, subordinate=0f, sec-latency=0
I/O behind bridge: 0000d000-0000dfff
Memory behind bridge: f6600000-f68fffff
Prefetchable memory behind bridge: 00000000f0000000-00000000f01fffff
Secondary status: 66MHz- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort-
<MAbort- <SERR- <PERR-
BridgeCtl: Parity- SERR+ NoISA- VGA- MAbort- >Reset- FastB2B-
PriDiscTmr- SecDiscTmr- DiscTmrStat- DiscTmrSERREn-
Capabilities: <access denied>
Kernel driver in use: pcieport
00:1d.0 USB controller [0c03]: Intel Corporation 82801I (ICH9 Family)
USB UHCI Controller #1 [8086:2934] (rev 03) (prog-if 00 [UHCI])
Subsystem: Dell Device [1028:024f]
Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0
Interrupt: pin A routed to IRQ 20
Region 4: I/O ports at 6f00 [size=32]
Capabilities: <access denied>
Kernel driver in use: uhci_hcd
00:1d.1 USB controller [0c03]: Intel Corporation 82801I (ICH9 Family)
USB UHCI Controller #2 [8086:2935] (rev 03) (prog-if 00 [UHCI])
Subsystem: Dell Device [1028:024f]
Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0
Interrupt: pin B routed to IRQ 21
Region 4: I/O ports at 6f20 [size=32]
Capabilities: <access denied>
Kernel driver in use: uhci_hcd
00:1d.2 USB controller [0c03]: Intel Corporation 82801I (ICH9 Family)
USB UHCI Controller #3 [8086:2936] (rev 03) (prog-if 00 [UHCI])
Subsystem: Dell Device [1028:024f]
Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0
Interrupt: pin C routed to IRQ 22
Region 4: I/O ports at 6f40 [size=32]
Capabilities: <access denied>
Kernel driver in use: uhci_hcd
00:1d.7 USB controller [0c03]: Intel Corporation 82801I (ICH9 Family)
USB2 EHCI Controller #1 [8086:293a] (rev 03) (prog-if 20 [EHCI])
Subsystem: Dell Device [1028:024f]
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR+ FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0
Interrupt: pin A routed to IRQ 20
Region 0: Memory at fed1c000 (32-bit, non-prefetchable) [size=1K]
Capabilities: <access denied>
Kernel driver in use: ehci_hcd
00:1e.0 PCI bridge [0604]: Intel Corporation 82801 Mobile PCI Bridge
[8086:2448] (rev 93) (prog-if 01 [Subtractive decode])
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR+ FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort-
<MAbort- >SERR- <PERR- INTx-
Latency: 0
Bus: primary=00, secondary=03, subordinate=07, sec-latency=32
I/O behind bridge: 00002000-00002fff
Memory behind bridge: f6500000-f65fffff
Secondary status: 66MHz- FastB2B+ ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort+ <SERR- <PERR-
BridgeCtl: Parity- SERR+ NoISA- VGA- MAbort- >Reset- FastB2B-
PriDiscTmr- SecDiscTmr- DiscTmrStat- DiscTmrSERREn-
Capabilities: <access denied>
00:1f.0 ISA bridge [0601]: Intel Corporation ICH9M-E LPC Interface
Controller [8086:2917] (rev 03)
Subsystem: Dell Device [1028:024f]
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR+ FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0
Capabilities: <access denied>
00:1f.2 SATA controller [0106]: Intel Corporation 82801IBM/IEM
(ICH9M/ICH9M-E) 4 port SATA Controller [AHCI mode] [8086:2929] (rev 03)
(prog-if 01 [AHCI 1.0])
Subsystem: Dell Device [1028:024f]
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B- DisINTx+
Status: Cap+ 66MHz+ UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0
Interrupt: pin D routed to IRQ 44
Region 0: I/O ports at 6e70 [size=8]
Region 1: I/O ports at 6e78 [size=4]
Region 2: I/O ports at 6e80 [size=8]
Region 3: I/O ports at 6e88 [size=4]
Region 4: I/O ports at 6ea0 [size=32]
Region 5: Memory at fed1c800 (32-bit, non-prefetchable) [size=2K]
Capabilities: <access denied>
Kernel driver in use: ahci
00:1f.3 SMBus [0c05]: Intel Corporation 82801I (ICH9 Family) SMBus
Controller [8086:2930] (rev 03)
Subsystem: Dell Device [1028:024f]
Control: I/O+ Mem+ BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR+ FastB2B- DisINTx-
Status: Cap- 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR- INTx-
Interrupt: pin B routed to IRQ 19
Region 0: Memory at f6adaf00 (64-bit, non-prefetchable) [size=256]
Region 4: I/O ports at 1100 [size=32]
Kernel driver in use: i801_smbus
03:01.0 CardBus bridge [0607]: Ricoh Co Ltd RL5c476 II [1180:0476] (rev ba)
Subsystem: Dell Device [1028:024f]
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 168, Cache Line Size: 64 bytes
Interrupt: pin A routed to IRQ 19
Region 0: Memory at f4000000 (32-bit, non-prefetchable) [size=4K]
Bus: primary=03, secondary=04, subordinate=07, sec-latency=176
Memory window 0: f1000000-f13fffff (prefetchable)
Memory window 1: f1400000-f17fffff
I/O window 0: 00002400-000024ff
I/O window 1: 00002000-000020ff
BridgeCtl: Parity- SERR- ISA- VGA- MAbort- >Reset- 16bInt+ PostWrite+
16-bit legacy interface ports at 0001
Kernel driver in use: yenta_cardbus
03:01.1 FireWire (IEEE 1394) [0c00]: Ricoh Co Ltd R5C832 IEEE 1394
Controller [1180:0832] (rev 04) (prog-if 10 [OHCI])
Subsystem: Dell Device [1028:024f]
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR+ FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 64 (500ns min, 1000ns max), Cache Line Size: 64 bytes
Interrupt: pin B routed to IRQ 17
Region 0: Memory at f65ff800 (32-bit, non-prefetchable) [size=2K]
Capabilities: <access denied>
Kernel driver in use: firewire_ohci
03:01.2 SD Host controller [0805]: Ricoh Co Ltd R5C822
SD/SDIO/MMC/MS/MSPro Host Adapter [1180:0822] (rev 21) (prog-if 01)
Subsystem: Dell Device [1028:024f]
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR+ FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 64, Cache Line Size: 64 bytes
Interrupt: pin C routed to IRQ 18
Region 0: Memory at f65ff600 (32-bit, non-prefetchable) [size=256]
Capabilities: <access denied>
Kernel driver in use: sdhci-pci
0c:00.0 Network controller [0280]: Intel Corporation WiFi Link 5100
[8086:4232]
Subsystem: Intel Corporation WiFi Link 5100 AGN [8086:1321]
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR+ FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort-
<MAbort- >SERR- <PERR- INTx-
Latency: 0, Cache Line Size: 64 bytes
Interrupt: pin A routed to IRQ 46
Region 0: Memory at f69fe000 (64-bit, non-prefetchable) [size=8K]
Capabilities: <access denied>
Kernel driver in use: iwlwifi
** USB devices:
Bus 001 Device 001: ID 1d6b:0002 Linux Foundation 2.0 root hub
Bus 002 Device 001: ID 1d6b:0002 Linux Foundation 2.0 root hub
Bus 003 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub
Bus 004 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub
Bus 005 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub
Bus 006 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub
Bus 007 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub
Bus 008 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub
Bus 001 Device 004: ID 0c45:63f0 Microdia
Bus 005 Device 002: ID 0a5c:5800 Broadcom Corp. BCM5880 Secure
Applications Processor
Bus 006 Device 003: ID 1c4f:0003 SiGma Micro HID controller
-- System Information:
Debian Release: wheezy/sid
APT prefers unstable
APT policy: (500, 'unstable')
Architecture: amd64 (x86_64)
Kernel: Linux 3.3.0-trunk-amd64 (SMP w/2 CPU cores)
Locale: LANG=en_GB.UTF-8, LC_CTYPE=en_GB.UTF-8 (charmap=UTF-8)
Shell: /bin/sh linked to /bin/dash
Versions of packages linux-image-3.3.0-trunk-amd64 depends on:
ii debconf [debconf-2.0] 1.5.43
ii initramfs-tools [linux-initramfs-tool] 0.106
ii kmod 8-2
ii linux-base 3.5
ii module-init-tools 8-2
Versions of packages linux-image-3.3.0-trunk-amd64 recommends:
pn firmware-linux-free <none>
Versions of packages linux-image-3.3.0-trunk-amd64 suggests:
ii grub-pc 1.99-22
pn linux-doc-3.3 <none>
Versions of packages linux-image-3.3.0-trunk-amd64 is related to:
pn firmware-atheros <none>
pn firmware-bnx2 <none>
pn firmware-bnx2x <none>
pn firmware-brcm80211 <none>
pn firmware-intelwimax <none>
pn firmware-ipw2x00 <none>
pn firmware-ivtv <none>
ii firmware-iwlwifi 0.34
pn firmware-libertas <none>
pn firmware-linux <none>
pn firmware-linux-nonfree <none>
pn firmware-myricom <none>
pn firmware-netxen <none>
pn firmware-qlogic <none>
pn firmware-ralink <none>
pn firmware-realtek <none>
pn xen-hypervisor <none>
-- debconf information:
linux-image-3.3.0-trunk-amd64/prerm/removing-running-kernel-3.3.0-trunk-amd64:
true
linux-image-3.3.0-trunk-amd64/postinst/depmod-error-initrd-3.3.0-trunk-amd64:
false
linux-image-3.3.0-trunk-amd64/postinst/ignoring-ramdisk:
* linux-image-3.3.0-trunk-amd64/postinst/missing-firmware-3.3.0-trunk-amd64:
Reply to: