[Date Prev][Date Next] [Thread Prev][Thread Next] [Date Index] [Thread Index]

Bug#665493: linux-image-3.2.0-2-amd64: kernel fails to boot completely (timeout on modprobe -b pci:xxxx)



Package: linux-2.6
Version: 3.2.12-1
Severity: normal

After today's upgrade linux-image-3.2.0-2-amd64 fails to boot - 
version 3.2.9-1 was ok (and linux-image-3.2.0-1  version 3.2.6-1 still boots,
fortunately).
I could boot into the single user kernel -- but I had to press
control-C at some point to get the booting to continue.
Also, after a while udev starts complaining:

udevd[364]: timeout: killing '/sbin/modprobe -b pci:v00008086d00001C20sv0000103Csd00003581bc04sc03i00' [411]

udevd[366]: timeout: killing '/sbin/modprobe -b pci:v00001002d00006760sv0000103Csd00003581bc03sc00i00' [411]

over and over again. I've included the dmesg output below under 'Kernel log'.
There's an Oops in there: 
[    7.869997] [drm:drm_pci_agp_init] *ERROR* Cannot initialize the agpgart modu
le.
[    7.870078] BUG: unable to handle kernel paging request at 0000000000001990
[    7.870223] IP: [<ffffffffa02b82ee>] intel_fb_restore_mode+0x9/0x3f [i915]
[    7.870349] PGD 252ae2067 PUD 2554e8067 PMD 0 
[    7.870529] Oops: 0000 [#1] SMP
...
( I pressed control-C after 10s, so after the cfg80211 messages)


In multi-user mode I also get a long way, after pressing control-C at one point -- but X and/or gdm never manage to start.

( apologies if this was reported already - bugs.debian.org timed out on
  bugs for src:linux-2.6 )

Best regards,

Jeroen Nijhof

-- Package-specific info:
** Kernel log: boot messages should be attached

[    0.000000] Initializing cgroup subsys cpuset
[    0.000000] Initializing cgroup subsys cpu
[    0.000000] Linux version 3.2.0-2-amd64 (Debian 3.2.12-1) (debian-kernel@lists.debian.org) (gcc version 4.6.3 (Debian 4.6.3-1) ) #1 SMP Tue Mar 20 18:36:37 UTC 2012
[    0.000000] Command line: BOOT_IMAGE=/boot/vmlinuz-3.2.0-2-amd64 root=UUID=473793cd-80da-49de-bfef-10d024473409 ro single
[    0.000000] BIOS-provided physical RAM map:
[    0.000000]  BIOS-e820: 0000000000000000 - 000000000009d800 (usable)
[    0.000000]  BIOS-e820: 000000000009d800 - 00000000000a0000 (reserved)
[    0.000000]  BIOS-e820: 00000000000e0000 - 0000000000100000 (reserved)
[    0.000000]  BIOS-e820: 0000000000100000 - 000000009ce3f000 (usable)
[    0.000000]  BIOS-e820: 000000009ce3f000 - 000000009cebf000 (reserved)
[    0.000000]  BIOS-e820: 000000009cebf000 - 000000009cfbf000 (ACPI NVS)
[    0.000000]  BIOS-e820: 000000009cfbf000 - 000000009cfff000 (ACPI data)
[    0.000000]  BIOS-e820: 000000009cfff000 - 000000009d000000 (usable)
[    0.000000]  BIOS-e820: 000000009d000000 - 000000009fa00000 (reserved)
[    0.000000]  BIOS-e820: 00000000e0000000 - 00000000f0000000 (reserved)
[    0.000000]  BIOS-e820: 00000000feb00000 - 00000000feb04000 (reserved)
[    0.000000]  BIOS-e820: 00000000fec00000 - 00000000fec01000 (reserved)
[    0.000000]  BIOS-e820: 00000000fed10000 - 00000000fed1a000 (reserved)
[    0.000000]  BIOS-e820: 00000000fed1c000 - 00000000fed20000 (reserved)
[    0.000000]  BIOS-e820: 00000000fee00000 - 00000000fee01000 (reserved)
[    0.000000]  BIOS-e820: 00000000ffd80000 - 0000000100000000 (reserved)
[    0.000000]  BIOS-e820: 0000000100000000 - 000000025fe00000 (usable)
[    0.000000] NX (Execute Disable) protection: active
[    0.000000] DMI 2.7 present.
[    0.000000] DMI: Hewlett-Packard HP Pavilion dv6 Notebook PC/3581, BIOS F.1A 07/20/2011
[    0.000000] e820 update range: 0000000000000000 - 0000000000010000 (usable) ==> (reserved)
[    0.000000] e820 remove range: 00000000000a0000 - 0000000000100000 (usable)
[    0.000000] No AGP bridge found
[    0.000000] last_pfn = 0x25fe00 max_arch_pfn = 0x400000000
[    0.000000] MTRR default type: uncachable
[    0.000000] MTRR fixed ranges enabled:
[    0.000000]   00000-9FFFF write-back
[    0.000000]   A0000-BFFFF uncachable
[    0.000000]   C0000-FFFFF write-protect
[    0.000000] MTRR variable ranges enabled:
[    0.000000]   0 base 000000000 mask F80000000 write-back
[    0.000000]   1 base 080000000 mask FE0000000 write-back
[    0.000000]   2 base 09D000000 mask FFF000000 uncachable
[    0.000000]   3 base 09E000000 mask FFE000000 uncachable
[    0.000000]   4 base 0FFC00000 mask FFFC00000 write-protect
[    0.000000]   5 base 100000000 mask F00000000 write-back
[    0.000000]   6 base 200000000 mask FC0000000 write-back
[    0.000000]   7 base 240000000 mask FF0000000 write-back
[    0.000000]   8 base 250000000 mask FF0000000 write-back
[    0.000000]   9 base 25FE00000 mask FFFE00000 uncachable
[    0.000000] x86 PAT enabled: cpu 0, old 0x7040600070406, new 0x7010600070106
[    0.000000] last_pfn = 0x9d000 max_arch_pfn = 0x400000000
[    0.000000] found SMP MP-table at [ffff8800000fe1b0] fe1b0
[    0.000000] initial memory mapped : 0 - 20000000
[    0.000000] Base memory trampoline at [ffff880000098000] 98000 size 20480
[    0.000000] init_memory_mapping: 0000000000000000-000000009d000000
[    0.000000]  0000000000 - 009d000000 page 2M
[    0.000000] kernel direct mapping tables up to 9d000000 @ 1fffc000-20000000
[    0.000000] init_memory_mapping: 0000000100000000-000000025fe00000
[    0.000000]  0100000000 - 025fe00000 page 2M
[    0.000000] kernel direct mapping tables up to 25fe00000 @ 9ce34000-9ce3f000
[    0.000000] RAMDISK: 36a80000 - 37538000
[    0.000000] ACPI: RSDP 00000000000fe020 00024 (v02 HPQOEM)
[    0.000000] ACPI: XSDT 000000009cffe120 00094 (v01 HPQOEM SLIC-MPC 00000001      01000013)
[    0.000000] ACPI: FACP 000000009cffc000 000F4 (v04 HPQOEM SLIC-MPC 00000001 MSFT 01000013)
[    0.000000] ACPI: DSDT 000000009cfec000 0C553 (v01 HP     INSYDE   00000000 MSFT 01000013)
[    0.000000] ACPI: FACS 000000009cf6c000 00040
[    0.000000] ACPI: ASF! 000000009cffd000 000A5 (v32 HP     INSYDE   00000001 MSFT 01000013)
[    0.000000] ACPI: HPET 000000009cffb000 00038 (v01 HP     INSYDE   00000001 MSFT 01000013)
[    0.000000] ACPI: APIC 000000009cffa000 0008C (v02 HP     INSYDE   00000001 MSFT 01000013)
[    0.000000] ACPI: MCFG 000000009cff9000 0003C (v01 HP     INSYDE   00000001 MSFT 01000013)
[    0.000000] ACPI: SLIC 000000009cfeb000 00176 (v01 HPQOEM SLIC-MPC 00000001 MSFT 01000013)
[    0.000000] ACPI: SSDT 000000009cfea000 0051F (v01 HP     INSYDE   00001000 MSFT 01000013)
[    0.000000] ACPI: BOOT 000000009cfe8000 00028 (v01 HP     INSYDE   00000001 MSFT 01000013)
[    0.000000] ACPI: ASPT 000000009cfe5000 00034 (v07 HP     INSYDE   00000001 MSFT 01000013)
[    0.000000] ACPI: SSDT 000000009cfe4000 0094E (v01 HP     INSYDE   00003000 INTL 20100806)
[    0.000000] ACPI: SSDT 000000009cfe3000 00996 (v01 HP     INSYDE   00003000 INTL 20100806)
[    0.000000] ACPI: SSDT 000000009cfe2000 002DA (v01 HP     INSYDE   00003000 INTL 20100806)
[    0.000000] ACPI: SSDT 000000009cfe1000 0035D (v01 HP     INSYDE   00003000 INTL 20100806)
[    0.000000] ACPI: SSDT 000000009cfdb000 024A1 (v01 HP     INSYDE   00001000 INTL 20100806)
[    0.000000] ACPI: Local APIC address 0xfee00000
[    0.000000] No NUMA configuration found
[    0.000000] Faking a node at 0000000000000000-000000025fe00000
[    0.000000] Initmem setup node 0 0000000000000000-000000025fe00000
[    0.000000]   NODE_DATA [000000025fdfb000 - 000000025fdfffff]
[    0.000000]  [ffffea0000000000-ffffea00085fffff] PMD -> [ffff880257400000-ffff88025e5fffff] on node 0
[    0.000000] Zone PFN ranges:
[    0.000000]   DMA      0x00000010 -> 0x00001000
[    0.000000]   DMA32    0x00001000 -> 0x00100000
[    0.000000]   Normal   0x00100000 -> 0x0025fe00
[    0.000000] Movable zone start PFN for each node
[    0.000000] early_node_map[4] active PFN ranges
[    0.000000]     0: 0x00000010 -> 0x0000009d
[    0.000000]     0: 0x00000100 -> 0x0009ce3f
[    0.000000]     0: 0x0009cfff -> 0x0009d000
[    0.000000]     0: 0x00100000 -> 0x0025fe00
[    0.000000] On node 0 totalpages: 2083789
[    0.000000]   DMA zone: 56 pages used for memmap
[    0.000000]   DMA zone: 5 pages reserved
[    0.000000]   DMA zone: 3920 pages, LIFO batch:0
[    0.000000]   DMA32 zone: 14280 pages used for memmap
[    0.000000]   DMA32 zone: 624248 pages, LIFO batch:31
[    0.000000]   Normal zone: 19705 pages used for memmap
[    0.000000]   Normal zone: 1421575 pages, LIFO batch:31
[    0.000000] ACPI: PM-Timer IO Port: 0x408
[    0.000000] ACPI: Local APIC address 0xfee00000
[    0.000000] ACPI: LAPIC (acpi_id[0x01] lapic_id[0x00] enabled)
[    0.000000] ACPI: LAPIC (acpi_id[0x02] lapic_id[0x01] enabled)
[    0.000000] ACPI: LAPIC (acpi_id[0x03] lapic_id[0x02] enabled)
[    0.000000] ACPI: LAPIC (acpi_id[0x04] lapic_id[0x03] enabled)
[    0.000000] ACPI: LAPIC (acpi_id[0x05] lapic_id[0x04] enabled)
[    0.000000] ACPI: LAPIC (acpi_id[0x06] lapic_id[0x05] enabled)
[    0.000000] ACPI: LAPIC (acpi_id[0x07] lapic_id[0x06] enabled)
[    0.000000] ACPI: LAPIC (acpi_id[0x08] lapic_id[0x07] enabled)
[    0.000000] ACPI: IOAPIC (id[0x00] address[0xfec00000] gsi_base[0])
[    0.000000] IOAPIC[0]: apic_id 0, version 32, address 0xfec00000, GSI 0-23
[    0.000000] ACPI: INT_SRC_OVR (bus 0 bus_irq 0 global_irq 2 dfl dfl)
[    0.000000] ACPI: INT_SRC_OVR (bus 0 bus_irq 9 global_irq 9 high level)
[    0.000000] ACPI: IRQ0 used by override.
[    0.000000] ACPI: IRQ2 used by override.
[    0.000000] ACPI: IRQ9 used by override.
[    0.000000] Using ACPI (MADT) for SMP configuration information
[    0.000000] ACPI: HPET id: 0x8086a201 base: 0xfed00000
[    0.000000] SMP: Allowing 8 CPUs, 0 hotplug CPUs
[    0.000000] nr_irqs_gsi: 40
[    0.000000] PM: Registered nosave memory: 000000000009d000 - 000000000009e000
[    0.000000] PM: Registered nosave memory: 000000000009e000 - 00000000000a0000
[    0.000000] PM: Registered nosave memory: 00000000000a0000 - 00000000000e0000
[    0.000000] PM: Registered nosave memory: 00000000000e0000 - 0000000000100000
[    0.000000] PM: Registered nosave memory: 000000009ce3f000 - 000000009cebf000
[    0.000000] PM: Registered nosave memory: 000000009cebf000 - 000000009cfbf000
[    0.000000] PM: Registered nosave memory: 000000009cfbf000 - 000000009cfff000
[    0.000000] PM: Registered nosave memory: 000000009d000000 - 000000009fa00000
[    0.000000] PM: Registered nosave memory: 000000009fa00000 - 00000000e0000000
[    0.000000] PM: Registered nosave memory: 00000000e0000000 - 00000000f0000000
[    0.000000] PM: Registered nosave memory: 00000000f0000000 - 00000000feb00000
[    0.000000] PM: Registered nosave memory: 00000000feb00000 - 00000000feb04000
[    0.000000] PM: Registered nosave memory: 00000000feb04000 - 00000000fec00000
[    0.000000] PM: Registered nosave memory: 00000000fec00000 - 00000000fec01000
[    0.000000] PM: Registered nosave memory: 00000000fec01000 - 00000000fed10000
[    0.000000] PM: Registered nosave memory: 00000000fed10000 - 00000000fed1a000
[    0.000000] PM: Registered nosave memory: 00000000fed1a000 - 00000000fed1c000
[    0.000000] PM: Registered nosave memory: 00000000fed1c000 - 00000000fed20000
[    0.000000] PM: Registered nosave memory: 00000000fed20000 - 00000000fee00000
[    0.000000] PM: Registered nosave memory: 00000000fee00000 - 00000000fee01000
[    0.000000] PM: Registered nosave memory: 00000000fee01000 - 00000000ffd80000
[    0.000000] PM: Registered nosave memory: 00000000ffd80000 - 0000000100000000
[    0.000000] Allocating PCI resources starting at 9fa00000 (gap: 9fa00000:40600000)
[    0.000000] Booting paravirtualized kernel on bare hardware
[    0.000000] setup_percpu: NR_CPUS:512 nr_cpumask_bits:512 nr_cpu_ids:8 nr_node_ids:1
[    0.000000] PERCPU: Embedded 28 pages/cpu @ffff88025fa00000 s82304 r8192 d24192 u262144
[    0.000000] pcpu-alloc: s82304 r8192 d24192 u262144 alloc=1*2097152
[    0.000000] pcpu-alloc: [0] 0 1 2 3 4 5 6 7 
[    0.000000] Built 1 zonelists in Zone order, mobility grouping on.  Total pages: 2049743
[    0.000000] Policy zone: Normal
[    0.000000] Kernel command line: BOOT_IMAGE=/boot/vmlinuz-3.2.0-2-amd64 root=UUID=473793cd-80da-49de-bfef-10d024473409 ro single
[    0.000000] PID hash table entries: 4096 (order: 3, 32768 bytes)
[    0.000000] xsave/xrstor: enabled xstate_bv 0x7, cntxt size 0x340
[    0.000000] Checking aperture...
[    0.000000] No AGP bridge found
[    0.000000] Calgary: detecting Calgary via BIOS EBDA area
[    0.000000] Calgary: Unable to locate Rio Grande table in EBDA - bailing!
[    0.000000] Memory: 8131952k/9959424k available (3402k kernel code, 1624268k absent, 203204k reserved, 3330k data, 568k init)
[    0.000000] Hierarchical RCU implementation.
[    0.000000] 	RCU dyntick-idle grace-period acceleration is enabled.
[    0.000000] NR_IRQS:33024 nr_irqs:744 16
[    0.000000] Extended CMOS year: 2000
[    0.000000] Console: colour VGA+ 80x25
[    0.000000] console [tty0] enabled
[    0.000000] hpet clockevent registered
[    0.000000] Fast TSC calibration using PIT
[    0.004000] Detected 2195.022 MHz processor.
[    0.000003] Calibrating delay loop (skipped), value calculated using timer frequency.. 4390.04 BogoMIPS (lpj=8780088)
[    0.000127] pid_max: default: 32768 minimum: 301
[    0.000226] Security Framework initialized
[    0.000289] AppArmor: AppArmor disabled by boot time parameter
[    0.001065] Dentry cache hash table entries: 1048576 (order: 11, 8388608 bytes)
[    0.002997] Inode-cache hash table entries: 524288 (order: 10, 4194304 bytes)
[    0.003810] Mount-cache hash table entries: 256
[    0.004000] Initializing cgroup subsys cpuacct
[    0.004064] Initializing cgroup subsys memory
[    0.004134] Initializing cgroup subsys devices
[    0.004196] Initializing cgroup subsys freezer
[    0.004255] Initializing cgroup subsys net_cls
[    0.004316] Initializing cgroup subsys blkio
[    0.004378] Initializing cgroup subsys perf_event
[    0.004466] CPU: Physical Processor ID: 0
[    0.004525] CPU: Processor Core ID: 0
[    0.004587] ENERGY_PERF_BIAS: Set to 'normal', was 'performance'
[    0.004588] ENERGY_PERF_BIAS: View and update with x86_energy_perf_policy(8)
[    0.004715] mce: CPU supports 9 MCE banks
[    0.004785] CPU0: Thermal monitoring handled by SMI
[    0.004792] using mwait in idle threads.
[    0.005336] ACPI: Core revision 20110623
[    0.030216] x2apic not enabled, IRQ remapping init failed
[    0.030695] ..TIMER: vector=0x30 apic1=0 pin1=2 apic2=-1 pin2=-1
[    0.070398] CPU0: Intel(R) Core(TM) i7-2670QM CPU @ 2.20GHz stepping 07
[    0.175644] Performance Events: PEBS fmt1+, SandyBridge events, Intel PMU driver.
[    0.175842] PEBS disabled due to CPU errata.
[    0.175902] ... version:                3
[    0.175961] ... bit width:              48
[    0.176020] ... generic registers:      4
[    0.176080] ... value mask:             0000ffffffffffff
[    0.176141] ... max period:             000000007fffffff
[    0.176202] ... fixed-purpose events:   3
[    0.176260] ... event mask:             000000070000000f
[    0.176460] NMI watchdog enabled, takes one hw-pmu counter.
[    0.176618] Booting Node   0, Processors  #1
[    0.176706] smpboot cpu 1: start_ip = 98000
[    0.267564] CPU1: Thermal monitoring handled by SMI
[    0.287629] NMI watchdog enabled, takes one hw-pmu counter.
[    0.287793]  #2
[    0.287836] smpboot cpu 2: start_ip = 98000
[    0.375438] CPU2: Thermal monitoring handled by SMI
[    0.395550] NMI watchdog enabled, takes one hw-pmu counter.
[    0.395710]  #3
[    0.395752] smpboot cpu 3: start_ip = 98000
[    0.483313] CPU3: Thermal monitoring handled by SMI
[    0.503368] NMI watchdog enabled, takes one hw-pmu counter.
[    0.503528]  #4
[    0.503571] smpboot cpu 4: start_ip = 98000
[    0.591190] CPU4: Thermal monitoring handled by SMI
[    0.611282] NMI watchdog enabled, takes one hw-pmu counter.
[    0.611440]  #5
[    0.611483] smpboot cpu 5: start_ip = 98000
[    0.699064] CPU5: Thermal monitoring handled by SMI
[    0.719099] NMI watchdog enabled, takes one hw-pmu counter.
[    0.719258]  #6
[    0.719301] smpboot cpu 6: start_ip = 98000
[    0.806941] CPU6: Thermal monitoring handled by SMI
[    0.827014] NMI watchdog enabled, takes one hw-pmu counter.
[    0.827174]  #7 Ok.
[    0.827230] smpboot cpu 7: start_ip = 98000
[    0.914816] CPU7: Thermal monitoring handled by SMI
[    0.934893] NMI watchdog enabled, takes one hw-pmu counter.
[    0.934980] Brought up 8 CPUs
[    0.935038] Total of 8 processors activated (35118.88 BogoMIPS).
[    0.942917] devtmpfs: initialized
[    0.947577] PM: Registering ACPI NVS region at 9cebf000 (1048576 bytes)
[    0.947832] print_constraints: dummy: 
[    0.947951] NET: Registered protocol family 16
[    0.948102] ACPI FADT declares the system doesn't support PCIe ASPM, so disable it
[    0.948180] ACPI: bus type pci registered
[    0.948322] PCI: MMCONFIG for domain 0000 [bus 00-ff] at [mem 0xe0000000-0xefffffff] (base 0xe0000000)
[    0.948403] PCI: MMCONFIG at [mem 0xe0000000-0xefffffff] reserved in E820
[    0.970802] PCI: Using configuration type 1 for base access
[    0.971647] bio: create slab <bio-0> at 0
[    0.971802] ACPI: Added _OSI(Module Device)
[    0.971862] ACPI: Added _OSI(Processor Device)
[    0.971922] ACPI: Added _OSI(3.0 _SCP Extensions)
[    0.971983] ACPI: Added _OSI(Processor Aggregator Device)
[    0.973633] ACPI: EC: Look up EC in DSDT
[    0.975143] ACPI: Executed 1 blocks of module-level executable AML code
[    1.002797] [Firmware Bug]: ACPI: BIOS _OSI(Linux) query ignored
[    1.003499] ACPI: SSDT 000000009ce70798 00727 (v01  PmRef  Cpu0Cst 00003001 INTL 20100806)
[    1.004082] ACPI: Dynamic OEM Table Load:
[    1.004222] ACPI: SSDT           (null) 00727 (v01  PmRef  Cpu0Cst 00003001 INTL 20100806)
[    1.015092] ACPI: SSDT 000000009ce71a98 00303 (v01  PmRef    ApIst 00003000 INTL 20100806)
[    1.015727] ACPI: Dynamic OEM Table Load:
[    1.015867] ACPI: SSDT           (null) 00303 (v01  PmRef    ApIst 00003000 INTL 20100806)
[    1.026878] ACPI: SSDT 000000009ce6fd98 00119 (v01  PmRef    ApCst 00003000 INTL 20100806)
[    1.027444] ACPI: Dynamic OEM Table Load:
[    1.027582] ACPI: SSDT           (null) 00119 (v01  PmRef    ApCst 00003000 INTL 20100806)
[    1.043772] ACPI: Interpreter enabled
[    1.043832] ACPI: (supports S0 S3 S4 S5)
[    1.044079] ACPI: Using IOAPIC for interrupt routing
[    1.054085] ACPI: EC: GPE = 0x17, I/O: command/status = 0x66, data = 0x62
[    1.054585] ACPI: ACPI Dock Station Driver: 1 docks/bays found
[    1.054653] HEST: Table not found.
[    1.054712] PCI: Using host bridge windows from ACPI; if necessary, use "pci=nocrs" and report a bug
[    1.055223] \_SB_.PCI0:_OSC invalid UUID
[    1.055224] _OSC request data:1 8 1f 
[    1.055228] ACPI: PCI Root Bridge [PCI0] (domain 0000 [bus 00-fe])
[    1.056040] pci_root PNP0A08:00: host bridge window [io  0x0000-0x0cf7]
[    1.056105] pci_root PNP0A08:00: host bridge window [io  0x0d00-0xffff]
[    1.056169] pci_root PNP0A08:00: host bridge window [mem 0x000a0000-0x000bffff]
[    1.056246] pci_root PNP0A08:00: host bridge window [mem 0x9fa00000-0xfeafffff]
[    1.056334] pci 0000:00:00.0: [8086:0104] type 0 class 0x000600
[    1.056372] pci 0000:00:01.0: [8086:0101] type 1 class 0x000604
[    1.056405] pci 0000:00:01.0: PME# supported from D0 D3hot D3cold
[    1.056408] pci 0000:00:01.0: PME# disabled
[    1.056428] pci 0000:00:02.0: [8086:0116] type 0 class 0x000300
[    1.056438] pci 0000:00:02.0: reg 10: [mem 0xc0000000-0xc03fffff 64bit]
[    1.056445] pci 0000:00:02.0: reg 18: [mem 0xb0000000-0xbfffffff 64bit pref]
[    1.056449] pci 0000:00:02.0: reg 20: [io  0x6000-0x603f]
[    1.056506] pci 0000:00:16.0: [8086:1c3a] type 0 class 0x000780
[    1.056530] pci 0000:00:16.0: reg 10: [mem 0xc7404000-0xc740400f 64bit]
[    1.056609] pci 0000:00:16.0: PME# supported from D0 D3hot D3cold
[    1.056613] pci 0000:00:16.0: PME# disabled
[    1.056647] pci 0000:00:1a.0: [8086:1c2d] type 0 class 0x000c03
[    1.057015] pci 0000:00:1a.0: reg 10: [mem 0xc740a000-0xc740a3ff]
[    1.059172] pci 0000:00:1a.0: PME# supported from D0 D3hot D3cold
[    1.059177] pci 0000:00:1a.0: PME# disabled
[    1.059205] pci 0000:00:1b.0: [8086:1c20] type 0 class 0x000403
[    1.059221] pci 0000:00:1b.0: reg 10: [mem 0xc7400000-0xc7403fff 64bit]
[    1.059292] pci 0000:00:1b.0: PME# supported from D0 D3hot D3cold
[    1.059297] pci 0000:00:1b.0: PME# disabled
[    1.059320] pci 0000:00:1c.0: [8086:1c10] type 1 class 0x000604
[    1.059403] pci 0000:00:1c.0: PME# supported from D0 D3hot D3cold
[    1.059407] pci 0000:00:1c.0: PME# disabled
[    1.059432] pci 0000:00:1c.1: [8086:1c12] type 1 class 0x000604
[    1.059514] pci 0000:00:1c.1: PME# supported from D0 D3hot D3cold
[    1.059518] pci 0000:00:1c.1: PME# disabled
[    1.059544] pci 0000:00:1c.2: [8086:1c14] type 1 class 0x000604
[    1.059626] pci 0000:00:1c.2: PME# supported from D0 D3hot D3cold
[    1.059631] pci 0000:00:1c.2: PME# disabled
[    1.059665] pci 0000:00:1d.0: [8086:1c26] type 0 class 0x000c03
[    1.060025] pci 0000:00:1d.0: reg 10: [mem 0xc7409000-0xc74093ff]
[    1.062162] pci 0000:00:1d.0: PME# supported from D0 D3hot D3cold
[    1.062167] pci 0000:00:1d.0: PME# disabled
[    1.062194] pci 0000:00:1f.0: [8086:1c49] type 0 class 0x000601
[    1.062324] pci 0000:00:1f.2: [8086:1c03] type 0 class 0x000106
[    1.062344] pci 0000:00:1f.2: reg 10: [io  0x6098-0x609f]
[    1.062353] pci 0000:00:1f.2: reg 14: [io  0x60bc-0x60bf]
[    1.062361] pci 0000:00:1f.2: reg 18: [io  0x6090-0x6097]
[    1.062370] pci 0000:00:1f.2: reg 1c: [io  0x60b8-0x60bb]
[    1.062378] pci 0000:00:1f.2: reg 20: [io  0x6060-0x607f]
[    1.062387] pci 0000:00:1f.2: reg 24: [mem 0xc7408000-0xc74087ff]
[    1.062434] pci 0000:00:1f.2: PME# supported from D3hot
[    1.062438] pci 0000:00:1f.2: PME# disabled
[    1.062457] pci 0000:00:1f.3: [8086:1c22] type 0 class 0x000c05
[    1.062474] pci 0000:00:1f.3: reg 10: [mem 0xc7406000-0xc74060ff 64bit]
[    1.062496] pci 0000:00:1f.3: reg 20: [io  0x6040-0x605f]
[    1.062559] pci 0000:01:00.0: [1002:6760] type 0 class 0x000300
[    1.062575] pci 0000:01:00.0: reg 10: [mem 0xa0000000-0xafffffff 64bit pref]
[    1.062589] pci 0000:01:00.0: reg 18: [mem 0xc6400000-0xc641ffff 64bit]
[    1.062598] pci 0000:01:00.0: reg 20: [io  0x5000-0x50ff]
[    1.062614] pci 0000:01:00.0: reg 30: [mem 0xfffe0000-0xffffffff pref]
[    1.062656] pci 0000:01:00.0: supports D1 D2
[    1.070635] pci 0000:00:01.0: PCI bridge to [bus 01-06]
[    1.070729] pci 0000:00:01.0:   bridge window [io  0x5000-0x5fff]
[    1.070732] pci 0000:00:01.0:   bridge window [mem 0xc6400000-0xc73fffff]
[    1.070736] pci 0000:00:01.0:   bridge window [mem 0xa0000000-0xafffffff 64bit pref]
[    1.070806] pci 0000:07:00.0: [10ec:8168] type 0 class 0x000200
[    1.070827] pci 0000:07:00.0: reg 10: [io  0x4000-0x40ff]
[    1.070862] pci 0000:07:00.0: reg 18: [mem 0xc0404000-0xc0404fff 64bit pref]
[    1.070884] pci 0000:07:00.0: reg 20: [mem 0xc0400000-0xc0403fff 64bit pref]
[    1.070979] pci 0000:07:00.0: supports D1 D2
[    1.070981] pci 0000:07:00.0: PME# supported from D0 D1 D2 D3hot D3cold
[    1.070987] pci 0000:07:00.0: PME# disabled
[    1.078634] pci 0000:00:1c.0: PCI bridge to [bus 07-0c]
[    1.078728] pci 0000:00:1c.0:   bridge window [io  0x4000-0x4fff]
[    1.078732] pci 0000:00:1c.0:   bridge window [mem 0xc5400000-0xc63fffff]
[    1.078739] pci 0000:00:1c.0:   bridge window [mem 0xc0400000-0xc13fffff 64bit pref]
[    1.078846] pci 0000:0d:00.0: [14e4:4727] type 0 class 0x000280
[    1.078881] pci 0000:0d:00.0: reg 10: [mem 0xc4400000-0xc4403fff 64bit]
[    1.079048] pci 0000:0d:00.0: supports D1 D2
[    1.086655] pci 0000:00:1c.1: PCI bridge to [bus 0d-12]
[    1.086739] pci 0000:00:1c.1:   bridge window [io  0x3000-0x3fff]
[    1.086743] pci 0000:00:1c.1:   bridge window [mem 0xc4400000-0xc53fffff]
[    1.086750] pci 0000:00:1c.1:   bridge window [mem 0xc1400000-0xc23fffff 64bit pref]
[    1.086821] pci 0000:13:00.0: [10ec:5209] type 0 class 0x00ff00
[    1.086842] pci 0000:13:00.0: reg 10: [mem 0xc3400000-0xc3400fff]
[    1.086926] pci 0000:13:00.0: reg 30: [mem 0xffff0000-0xffffffff pref]
[    1.086997] pci 0000:13:00.0: supports D1 D2
[    1.086998] pci 0000:13:00.0: PME# supported from D1 D2 D3hot
[    1.087004] pci 0000:13:00.0: PME# disabled
[    1.094615] pci 0000:00:1c.2: PCI bridge to [bus 13-18]
[    1.094710] pci 0000:00:1c.2:   bridge window [io  0x2000-0x2fff]
[    1.094714] pci 0000:00:1c.2:   bridge window [mem 0xc3400000-0xc43fffff]
[    1.094721] pci 0000:00:1c.2:   bridge window [mem 0xc2400000-0xc33fffff 64bit pref]
[    1.094742] ACPI: PCI Interrupt Routing Table [\_SB_.PCI0._PRT]
[    1.095001] ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.RP01._PRT]
[    1.095051] ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.RP02._PRT]
[    1.095099] ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.RP03._PRT]
[    1.095167] ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.PEG0._PRT]
[    1.095276] \_SB_.PCI0:_OSC invalid UUID
[    1.095277] _OSC request data:1 1f 1f 
[    1.095281]  pci0000:00: Requesting ACPI _OSC control (0x1d)
[    1.095386] \_SB_.PCI0:_OSC invalid UUID
[    1.095387] _OSC request data:1 0 1d 
[    1.095391]  pci0000:00: ACPI _OSC request failed (AE_ERROR), returned control mask: 0x1d
[    1.095469] ACPI _OSC control for PCIe not granted, disabling ASPM
[    1.100345] ACPI: PCI Interrupt Link [LNKA] (IRQs 1 3 4 5 6 10 11 12 14 15) *7
[    1.100992] ACPI: PCI Interrupt Link [LNKB] (IRQs 1 *3 4 5 6 10 11 12 14 15)
[    1.101585] ACPI: PCI Interrupt Link [LNKC] (IRQs 1 3 *4 5 6 10 11 12 14 15)
[    1.102179] ACPI: PCI Interrupt Link [LNKD] (IRQs 1 3 4 5 6 *10 11 12 14 15)
[    1.102778] ACPI: PCI Interrupt Link [LNKE] (IRQs 1 3 4 5 6 10 11 12 14 15) *0, disabled.
[    1.103465] ACPI: PCI Interrupt Link [LNKF] (IRQs 1 3 4 *5 6 10 11 12 14 15)
[    1.104058] ACPI: PCI Interrupt Link [LNKG] (IRQs 1 3 4 5 6 *10 11 12 14 15)
[    1.104650] ACPI: PCI Interrupt Link [LNKH] (IRQs 1 3 4 5 6 10 *11 12 14 15)
[    1.105283] vgaarb: device added: PCI:0000:00:02.0,decodes=io+mem,owns=io+mem,locks=none
[    1.105370] vgaarb: device added: PCI:0000:01:00.0,decodes=io+mem,owns=none,locks=none
[    1.105449] vgaarb: loaded
[    1.105505] vgaarb: bridge control possible 0000:01:00.0
[    1.105567] vgaarb: no bridge control possible 0000:00:02.0
[    1.105663] PCI: Using ACPI for IRQ routing
[    1.112949] PCI: pci_cache_line_size set to 64 bytes
[    1.113060] reserve RAM buffer: 000000000009d800 - 000000000009ffff 
[    1.113062] reserve RAM buffer: 000000009ce3f000 - 000000009fffffff 
[    1.113066] reserve RAM buffer: 000000009d000000 - 000000009fffffff 
[    1.113068] reserve RAM buffer: 000000025fe00000 - 000000025fffffff 
[    1.113175] hpet0: at MMIO 0xfed00000, IRQs 2, 8, 0, 0, 0, 0, 0, 0
[    1.113595] hpet0: 8 comparators, 64-bit 14.318180 MHz counter
[    1.115673] Switching to clocksource hpet
[    1.117536] pnp: PnP ACPI init
[    1.117605] ACPI: bus type pnp registered
[    1.118044] pnp 00:00: [bus 00-fe]
[    1.118046] pnp 00:00: [io  0x0000-0x0cf7 window]
[    1.118048] pnp 00:00: [io  0x0cf8-0x0cff]
[    1.118050] pnp 00:00: [io  0x0d00-0xffff window]
[    1.118052] pnp 00:00: [mem 0x000a0000-0x000bffff window]
[    1.118054] pnp 00:00: [mem 0x000c0000-0x000c3fff window]
[    1.118056] pnp 00:00: [mem 0x000c4000-0x000c7fff window]
[    1.118058] pnp 00:00: [mem 0x000c8000-0x000cbfff window]
[    1.118060] pnp 00:00: [mem 0x000cc000-0x000cffff window]
[    1.118062] pnp 00:00: [mem 0x000d0000-0x000d3fff window]
[    1.118064] pnp 00:00: [mem 0x000d4000-0x000d7fff window]
[    1.118066] pnp 00:00: [mem 0x000d8000-0x000dbfff window]
[    1.118068] pnp 00:00: [mem 0x000dc000-0x000dffff window]
[    1.118070] pnp 00:00: [mem 0x000e0000-0x000e3fff window]
[    1.118072] pnp 00:00: [mem 0x000e4000-0x000e7fff window]
[    1.118074] pnp 00:00: [mem 0x000e8000-0x000ebfff window]
[    1.118076] pnp 00:00: [mem 0x000ec000-0x000effff window]
[    1.118080] pnp 00:00: [mem 0x000f0000-0x000fffff window]
[    1.118083] pnp 00:00: [mem 0x9fa00000-0xfeafffff window]
[    1.118129] pnp 00:00: Plug and Play ACPI device, IDs PNP0a08 PNP0a03 (active)
[    1.118150] pnp 00:01: [io  0x0000-0x001f]
[    1.118152] pnp 00:01: [io  0x0081-0x0091]
[    1.118153] pnp 00:01: [io  0x0093-0x009f]
[    1.118155] pnp 00:01: [io  0x00c0-0x00df]
[    1.118157] pnp 00:01: [dma 4]
[    1.118182] pnp 00:01: Plug and Play ACPI device, IDs PNP0200 (active)
[    1.118191] pnp 00:02: [mem 0xff000000-0xffffffff]
[    1.118214] pnp 00:02: Plug and Play ACPI device, IDs INT0800 (active)
[    1.118301] pnp 00:03: [mem 0xfed00000-0xfed003ff]
[    1.118326] pnp 00:03: Plug and Play ACPI device, IDs PNP0103 (active)
[    1.118337] pnp 00:04: [io  0x00f0]
[    1.118344] pnp 00:04: [irq 13]
[    1.118372] pnp 00:04: Plug and Play ACPI device, IDs PNP0c04 (active)
[    1.118383] pnp 00:05: [io  0x002e-0x002f]
[    1.118385] pnp 00:05: [io  0x004e-0x004f]
[    1.118387] pnp 00:05: [io  0x0061]
[    1.118389] pnp 00:05: [io  0x0063]
[    1.118390] pnp 00:05: [io  0x0065]
[    1.118392] pnp 00:05: [io  0x0067]
[    1.118393] pnp 00:05: [io  0x0070]
[    1.118395] pnp 00:05: [io  0x0080]
[    1.118396] pnp 00:05: [io  0x0092]
[    1.118398] pnp 00:05: [io  0x00b2-0x00b3]
[    1.118400] pnp 00:05: [io  0x0680-0x069f]
[    1.118401] pnp 00:05: [io  0x1000-0x100f]
[    1.118403] pnp 00:05: [io  0x1010-0x1013]
[    1.118405] pnp 00:05: [io  0xffff]
[    1.118406] pnp 00:05: [io  0x0400-0x0453]
[    1.118408] pnp 00:05: [io  0x0458-0x047f]
[    1.118410] pnp 00:05: [io  0x0500-0x057f]
[    1.118411] pnp 00:05: [io  0x164e-0x164f]
[    1.118457] system 00:05: [io  0x0680-0x069f] has been reserved
[    1.118521] system 00:05: [io  0x1000-0x100f] has been reserved
[    1.118600] system 00:05: [io  0x1010-0x1013] has been reserved
[    1.118673] system 00:05: [io  0xffff] has been reserved
[    1.118746] system 00:05: [io  0x0400-0x0453] has been reserved
[    1.118810] system 00:05: [io  0x0458-0x047f] has been reserved
[    1.118873] system 00:05: [io  0x0500-0x057f] has been reserved
[    1.118936] system 00:05: [io  0x164e-0x164f] has been reserved
[    1.119000] system 00:05: Plug and Play ACPI device, IDs PNP0c02 (active)
[    1.119012] pnp 00:06: [io  0x0070-0x0077]
[    1.119017] pnp 00:06: [irq 8]
[    1.119042] pnp 00:06: Plug and Play ACPI device, IDs PNP0b00 (active)
[    1.119065] pnp 00:07: [io  0x0454-0x0457]
[    1.119105] system 00:07: [io  0x0454-0x0457] has been reserved
[    1.119169] system 00:07: Plug and Play ACPI device, IDs INT3f0d PNP0c02 (active)
[    1.119204] pnp 00:08: [io  0x0060]
[    1.119205] pnp 00:08: [io  0x0064]
[    1.119210] pnp 00:08: [irq 1]
[    1.119236] pnp 00:08: Plug and Play ACPI device, IDs PNP0303 (active)
[    1.119272] pnp 00:09: [irq 12]
[    1.119299] pnp 00:09: Plug and Play ACPI device, IDs SYN1e47 SYN1e00 SYN0002 PNP0f13 (active)
[    1.119425] pnp 00:0a: [mem 0xfed1c000-0xfed1ffff]
[    1.119427] pnp 00:0a: [mem 0xfed10000-0xfed17fff]
[    1.119429] pnp 00:0a: [mem 0xfed18000-0xfed18fff]
[    1.119431] pnp 00:0a: [mem 0xfed19000-0xfed19fff]
[    1.119433] pnp 00:0a: [mem 0xe0000000-0xefffffff]
[    1.119434] pnp 00:0a: [mem 0xfed20000-0xfed3ffff]
[    1.119436] pnp 00:0a: [mem 0xfed90000-0xfed93fff]
[    1.119438] pnp 00:0a: [mem 0xff000000-0xffffffff]
[    1.119440] pnp 00:0a: [mem 0xfee00000-0xfeefffff]
[    1.119442] pnp 00:0a: [mem 0x9fa00000-0x9fa00fff]
[    1.119486] system 00:0a: [mem 0xfed1c000-0xfed1ffff] has been reserved
[    1.119550] system 00:0a: [mem 0xfed10000-0xfed17fff] has been reserved
[    1.119615] system 00:0a: [mem 0xfed18000-0xfed18fff] has been reserved
[    1.119679] system 00:0a: [mem 0xfed19000-0xfed19fff] has been reserved
[    1.119752] system 00:0a: [mem 0xe0000000-0xefffffff] has been reserved
[    1.119816] system 00:0a: [mem 0xfed20000-0xfed3ffff] has been reserved
[    1.119881] system 00:0a: [mem 0xfed90000-0xfed93fff] has been reserved
[    1.119946] system 00:0a: [mem 0xff000000-0xffffffff] could not be reserved
[    1.120011] system 00:0a: [mem 0xfee00000-0xfeefffff] could not be reserved
[    1.120077] system 00:0a: [mem 0x9fa00000-0x9fa00fff] has been reserved
[    1.120141] system 00:0a: Plug and Play ACPI device, IDs PNP0c02 (active)
[    1.122044] pnp 00:0b: [irq 23]
[    1.122089] pnp 00:0b: Plug and Play ACPI device, IDs HPQ0004 (active)
[    1.122113] pnp 00:0c: [mem 0x20000000-0x201fffff]
[    1.122115] pnp 00:0c: [mem 0x40000000-0x401fffff]
[    1.122172] system 00:0c: [mem 0x20000000-0x201fffff] could not be reserved
[    1.122235] system 00:0c: [mem 0x40000000-0x401fffff] could not be reserved
[    1.122301] system 00:0c: Plug and Play ACPI device, IDs PNP0c01 (active)
[    1.122319] pnp: PnP ACPI: found 13 devices
[    1.122379] ACPI: ACPI bus type pnp unregistered
[    1.129198] pci 0000:01:00.0: no compatible bridge window for [mem 0xfffe0000-0xffffffff pref]
[    1.129280] pci 0000:13:00.0: no compatible bridge window for [mem 0xffff0000-0xffffffff pref]
[    1.129360] PCI: max bus depth: 1 pci_try_num: 2
[    1.129390] pci 0000:01:00.0: BAR 6: assigned [mem 0xc6420000-0xc643ffff pref]
[    1.129468] pci 0000:00:01.0: PCI bridge to [bus 01-06]
[    1.129530] pci 0000:00:01.0:   bridge window [io  0x5000-0x5fff]
[    1.129594] pci 0000:00:01.0:   bridge window [mem 0xc6400000-0xc73fffff]
[    1.129659] pci 0000:00:01.0:   bridge window [mem 0xa0000000-0xafffffff 64bit pref]
[    1.129739] pci 0000:00:1c.0: PCI bridge to [bus 07-0c]
[    1.129802] pci 0000:00:1c.0:   bridge window [io  0x4000-0x4fff]
[    1.129869] pci 0000:00:1c.0:   bridge window [mem 0xc5400000-0xc63fffff]
[    1.129936] pci 0000:00:1c.0:   bridge window [mem 0xc0400000-0xc13fffff 64bit pref]
[    1.130017] pci 0000:00:1c.1: PCI bridge to [bus 0d-12]
[    1.130080] pci 0000:00:1c.1:   bridge window [io  0x3000-0x3fff]
[    1.130145] pci 0000:00:1c.1:   bridge window [mem 0xc4400000-0xc53fffff]
[    1.130212] pci 0000:00:1c.1:   bridge window [mem 0xc1400000-0xc23fffff 64bit pref]
[    1.130294] pci 0000:13:00.0: BAR 6: assigned [mem 0xc2400000-0xc240ffff pref]
[    1.130371] pci 0000:00:1c.2: PCI bridge to [bus 13-18]
[    1.130434] pci 0000:00:1c.2:   bridge window [io  0x2000-0x2fff]
[    1.130499] pci 0000:00:1c.2:   bridge window [mem 0xc3400000-0xc43fffff]
[    1.130566] pci 0000:00:1c.2:   bridge window [mem 0xc2400000-0xc33fffff 64bit pref]
[    1.130657] pci 0000:00:01.0: PCI INT A -> GSI 16 (level, low) -> IRQ 16
[    1.130722] pci 0000:00:01.0: setting latency timer to 64
[    1.130732] pci 0000:00:1c.0: PCI INT A -> GSI 17 (level, low) -> IRQ 17
[    1.130798] pci 0000:00:1c.0: setting latency timer to 64
[    1.130805] pci 0000:00:1c.1: PCI INT B -> GSI 16 (level, low) -> IRQ 16
[    1.130872] pci 0000:00:1c.1: setting latency timer to 64
[    1.130882] pci 0000:00:1c.2: PCI INT C -> GSI 18 (level, low) -> IRQ 18
[    1.130948] pci 0000:00:1c.2: setting latency timer to 64
[    1.130952] pci_bus 0000:00: resource 4 [io  0x0000-0x0cf7]
[    1.130954] pci_bus 0000:00: resource 5 [io  0x0d00-0xffff]
[    1.130956] pci_bus 0000:00: resource 6 [mem 0x000a0000-0x000bffff]
[    1.130958] pci_bus 0000:00: resource 7 [mem 0x9fa00000-0xfeafffff]
[    1.130960] pci_bus 0000:01: resource 0 [io  0x5000-0x5fff]
[    1.130962] pci_bus 0000:01: resource 1 [mem 0xc6400000-0xc73fffff]
[    1.130964] pci_bus 0000:01: resource 2 [mem 0xa0000000-0xafffffff 64bit pref]
[    1.130966] pci_bus 0000:07: resource 0 [io  0x4000-0x4fff]
[    1.130968] pci_bus 0000:07: resource 1 [mem 0xc5400000-0xc63fffff]
[    1.130970] pci_bus 0000:07: resource 2 [mem 0xc0400000-0xc13fffff 64bit pref]
[    1.130972] pci_bus 0000:0d: resource 0 [io  0x3000-0x3fff]
[    1.130974] pci_bus 0000:0d: resource 1 [mem 0xc4400000-0xc53fffff]
[    1.130976] pci_bus 0000:0d: resource 2 [mem 0xc1400000-0xc23fffff 64bit pref]
[    1.130978] pci_bus 0000:13: resource 0 [io  0x2000-0x2fff]
[    1.130979] pci_bus 0000:13: resource 1 [mem 0xc3400000-0xc43fffff]
[    1.130981] pci_bus 0000:13: resource 2 [mem 0xc2400000-0xc33fffff 64bit pref]
[    1.131074] NET: Registered protocol family 2
[    1.131376] IP route cache hash table entries: 262144 (order: 9, 2097152 bytes)
[    1.132518] TCP established hash table entries: 524288 (order: 11, 8388608 bytes)
[    1.133892] TCP bind hash table entries: 65536 (order: 8, 1048576 bytes)
[    1.134081] TCP: Hash tables configured (established 524288 bind 65536)
[    1.134144] TCP reno registered
[    1.134217] UDP hash table entries: 4096 (order: 5, 131072 bytes)
[    1.134316] UDP-Lite hash table entries: 4096 (order: 5, 131072 bytes)
[    1.134519] NET: Registered protocol family 1
[    1.134592] pci 0000:00:02.0: Boot video device
[    1.134607] pci 0000:00:1a.0: PCI INT A -> GSI 16 (level, low) -> IRQ 16
[    1.147705] pci 0000:00:1a.0: PCI INT A disabled
[    1.147818] pci 0000:00:1d.0: PCI INT A -> GSI 20 (level, low) -> IRQ 20
[    1.163677] pci 0000:00:1d.0: PCI INT A disabled
[    1.163822] PCI: CLS 64 bytes, default 64
[    1.163868] Unpacking initramfs...
[    1.397368] Freeing initrd memory: 10976k freed
[    1.398743] PCI-DMA: Using software bounce buffering for IO (SWIOTLB)
[    1.398811] Placing 64MB software IO TLB between ffff880098e34000 - ffff88009ce34000
[    1.398889] software IO TLB at phys 0x98e34000 - 0x9ce34000
[    1.398968] Simple Boot Flag at 0x44 set to 0x1
[    1.399778] audit: initializing netlink socket (disabled)
[    1.399848] type=2000 audit(1332610416.168:1): initialized
[    1.423759] HugeTLB registered 2 MB page size, pre-allocated 0 pages
[    1.440928] VFS: Disk quotas dquot_6.5.2
[    1.441026] Dquot-cache hash table entries: 512 (order 0, 4096 bytes)
[    1.441165] msgmni has been set to 15904
[    1.441386] alg: No test for stdrng (krng)
[    1.441480] Block layer SCSI generic (bsg) driver version 0.4 loaded (major 253)
[    1.441559] io scheduler noop registered
[    1.441618] io scheduler deadline registered
[    1.441704] io scheduler cfq registered (default)
[    1.441846] pcieport 0000:00:01.0: setting latency timer to 64
[    1.441872] pcieport 0000:00:01.0: irq 40 for MSI/MSI-X
[    1.442068] pci_hotplug: PCI Hot Plug PCI Core version: 0.5
[    1.442153] pciehp: PCI Express Hot Plug Controller Driver version: 0.4
[    1.442217] acpiphp: ACPI Hot Plug PCI Controller Driver version: 0.5
[    1.442431] acpiphp: Slot [1] registered
[    1.442717] intel_idle: MWAIT substates: 0x21120
[    1.442718] intel_idle: v0.4 model 0x2A
[    1.442720] intel_idle: lapic_timer_reliable_states 0xffffffff
[    1.442780] ERST: Table is not found!
[    1.442838] GHES: HEST is not enabled!
[    1.442949] Serial: 8250/16550 driver, 4 ports, IRQ sharing enabled
[    1.635601] Linux agpgart interface v0.103
[    1.635736] agpgart-intel 0000:00:00.0: Intel Sandybridge Chipset
[    1.635868] agpgart-intel 0000:00:00.0: detected gtt size: 2097152K total, 262144K mappable
[    1.637087] agpgart-intel 0000:00:00.0: detected 32768K stolen memory
[    1.637271] agpgart-intel 0000:00:00.0: AGP aperture is 256M @ 0xb0000000
[    1.638863] i8042: PNP: PS/2 Controller [PNP0303:PS2K,PNP0f13:PS2M] at 0x60,0x64 irq 1,12
[    1.646199] serio: i8042 KBD port at 0x60,0x64 irq 1
[    1.646266] serio: i8042 AUX port at 0x60,0x64 irq 12
[    1.646451] mousedev: PS/2 mouse device common for all mice
[    1.646544] rtc_cmos 00:06: RTC can wake from S4
[    1.646730] rtc_cmos 00:06: rtc core: registered rtc_cmos as rtc0
[    1.646824] rtc0: alarms up to one month, y3k, 242 bytes nvram, hpet irqs
[    1.647193] cpuidle: using governor ladder
[    1.647696] cpuidle: using governor menu
[    1.647930] TCP cubic registered
[    1.648195] NET: Registered protocol family 10
[    1.648824] Mobile IPv6
[    1.648881] NET: Registered protocol family 17
[    1.648943] Registering the dns_resolver key type
[    1.649445] PM: Hibernation image not present or could not be loaded.
[    1.649460] registered taskstats version 1
[    1.651232] input: AT Translated Set 2 keyboard as /devices/platform/i8042/serio0/input/input0
[    1.658393] rtc_cmos 00:06: setting system clock to 2012-03-24 17:33:36 UTC (1332610416)
[    1.658530] Initializing network drop monitor service
[    1.659651] Freeing unused kernel memory: 568k freed
[    1.659773] Write protecting the kernel read-only data: 6144k
[    1.662317] Freeing unused kernel memory: 676k freed
[    1.664779] Freeing unused kernel memory: 668k freed
[    1.728898] udevd[76]: starting version 175
[    1.746029] usbcore: registered new interface driver usbfs
[    1.746125] usbcore: registered new interface driver hub
[    1.748721] usbcore: registered new device driver usb
[    1.749297] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
[    1.749392] ehci_hcd 0000:00:1a.0: PCI INT A -> GSI 16 (level, low) -> IRQ 16
[    1.749484] ehci_hcd 0000:00:1a.0: setting latency timer to 64
[    1.749489] ehci_hcd 0000:00:1a.0: EHCI Host Controller
[    1.749582] ehci_hcd 0000:00:1a.0: new USB bus registered, assigned bus number 1
[    1.749700] ehci_hcd 0000:00:1a.0: debug port 2
[    1.751639] r8169 Gigabit Ethernet driver 2.3LK-NAPI loaded
[    1.751838] r8169 0000:07:00.0: PCI INT A -> GSI 16 (level, low) -> IRQ 16
[    1.752120] r8169 0000:07:00.0: setting latency timer to 64
[    1.752222] r8169 0000:07:00.0: irq 41 for MSI/MSI-X
[    1.752757] SCSI subsystem initialized
[    1.753108] r8169 0000:07:00.0: eth0: RTL8168evl/8111evl at 0xffffc90000c70000, 10:1f:74:18:86:21, XID 0c900800 IRQ 41
[    1.753263] r8169 0000:07:00.0: eth0: jumbo features [frames: 9200 bytes, tx checksumming: ko]
[    1.753651] ehci_hcd 0000:00:1a.0: cache line size of 64 is not supported
[    1.753672] ehci_hcd 0000:00:1a.0: irq 16, io mem 0xc740a000
[    1.754734] libata version 3.00 loaded.
[    1.760758] thermal LNXTHERM:00: registered as thermal_zone0
[    1.760823] ACPI: Thermal Zone [THRM] (69 C)
[    1.767087] ehci_hcd 0000:00:1a.0: USB 2.0 started, EHCI 1.00
[    1.767204] usb usb1: New USB device found, idVendor=1d6b, idProduct=0002
[    1.767268] usb usb1: New USB device strings: Mfr=3, Product=2, SerialNumber=1
[    1.767346] usb usb1: Product: EHCI Host Controller
[    1.767407] usb usb1: Manufacturer: Linux 3.2.0-2-amd64 ehci_hcd
[    1.767469] usb usb1: SerialNumber: 0000:00:1a.0
[    1.767755] hub 1-0:1.0: USB hub found
[    1.767819] hub 1-0:1.0: 2 ports detected
[    1.767953] ehci_hcd 0000:00:1d.0: PCI INT A -> GSI 20 (level, low) -> IRQ 20
[    1.768099] ehci_hcd 0000:00:1d.0: setting latency timer to 64
[    1.768103] ehci_hcd 0000:00:1d.0: EHCI Host Controller
[    1.768171] ehci_hcd 0000:00:1d.0: new USB bus registered, assigned bus number 2
[    1.768274] ehci_hcd 0000:00:1d.0: debug port 2
[    1.772210] ehci_hcd 0000:00:1d.0: cache line size of 64 is not supported
[    1.772293] ehci_hcd 0000:00:1d.0: irq 20, io mem 0xc7409000
[    1.787078] ehci_hcd 0000:00:1d.0: USB 2.0 started, EHCI 1.00
[    1.787189] usb usb2: New USB device found, idVendor=1d6b, idProduct=0002
[    1.787254] usb usb2: New USB device strings: Mfr=3, Product=2, SerialNumber=1
[    1.787331] usb usb2: Product: EHCI Host Controller
[    1.787392] usb usb2: Manufacturer: Linux 3.2.0-2-amd64 ehci_hcd
[    1.787455] usb usb2: SerialNumber: 0000:00:1d.0
[    1.787760] hub 2-0:1.0: USB hub found
[    1.787825] hub 2-0:1.0: 2 ports detected
[    1.787992] ahci 0000:00:1f.2: version 3.0
[    1.788025] ahci 0000:00:1f.2: PCI INT B -> GSI 19 (level, low) -> IRQ 19
[    1.788169] ahci 0000:00:1f.2: irq 42 for MSI/MSI-X
[    1.803082] ahci 0000:00:1f.2: AHCI 0001.0300 32 slots 6 ports 6 Gbps 0x21 impl SATA mode
[    1.803166] ahci 0000:00:1f.2: flags: 64bit ncq sntf pm led clo pio slum part ems apst 
[    1.803248] ahci 0000:00:1f.2: setting latency timer to 64
[    1.811688] scsi0 : ahci
[    1.812029] scsi1 : ahci
[    1.812254] scsi2 : ahci
[    1.812497] scsi3 : ahci
[    1.812734] scsi4 : ahci
[    1.812950] scsi5 : ahci
[    1.813129] ata1: SATA max UDMA/133 abar m2048@0xc7408000 port 0xc7408100 irq 42
[    1.813207] ata2: DUMMY
[    1.813263] ata3: DUMMY
[    1.813318] ata4: DUMMY
[    1.813375] ata5: DUMMY
[    1.813432] ata6: SATA max UDMA/133 abar m2048@0xc7408000 port 0xc7408380 irq 42
[    2.078765] usb 1-1: new high-speed USB device number 2 using ehci_hcd
[    2.130704] ata6: SATA link up 1.5 Gbps (SStatus 113 SControl 300)
[    2.134361] ata6.00: ATAPI: hp       CDDVDW TS-L633R, 0400, max UDMA/100
[    2.138698] ata1: SATA link up 3.0 Gbps (SStatus 123 SControl 300)
[    2.139198] ata1.00: ATA-8: TOSHIBA MK6476GSX, GS001C, max UDMA/100
[    2.139264] ata1.00: 1250263728 sectors, multi 16: LBA48 NCQ (depth 31/32), AA
[    2.139869] ata1.00: configured for UDMA/100
[    2.140185] scsi 0:0:0:0: Direct-Access     ATA      TOSHIBA MK6476GS GS00 PQ: 0 ANSI: 5
[    2.141373] ata6.00: configured for UDMA/100
[    2.149157] scsi 5:0:0:0: CD-ROM            hp       CDDVDW TS-L633R  0400 PQ: 0 ANSI: 5
[    2.153202] sd 0:0:0:0: [sda] 1250263728 512-byte logical blocks: (640 GB/596 GiB)
[    2.153340] sd 0:0:0:0: [sda] Write Protect is off
[    2.153402] sd 0:0:0:0: [sda] Mode Sense: 00 3a 00 00
[    2.153417] sd 0:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
[    2.211177] usb 1-1: New USB device found, idVendor=8087, idProduct=0024
[    2.211255] usb 1-1: New USB device strings: Mfr=0, Product=0, SerialNumber=0
[    2.211748] hub 1-1:1.0: USB hub found
[    2.211921] hub 1-1:1.0: 6 ports detected
[    2.268243]  sda: sda1 sda2 sda3 sda4 < sda5 sda6 >
[    2.269363] sd 0:0:0:0: [sda] Attached SCSI disk
[    2.281702] sr0: scsi3-mmc drive: 24x/24x writer dvd-ram cd/rw xa/form2 cdda tray
[    2.281784] cdrom: Uniform CD-ROM driver Revision: 3.20
[    2.282024] sr 5:0:0:0: Attached scsi CD-ROM sr0
[    2.322480] usb 2-1: new high-speed USB device number 2 using ehci_hcd
[    2.394392] Refined TSC clocksource calibration: 2195.013 MHz.
[    2.394479] Switching to clocksource tsc
[    2.454682] usb 2-1: New USB device found, idVendor=8087, idProduct=0024
[    2.454747] usb 2-1: New USB device strings: Mfr=0, Product=0, SerialNumber=0
[    2.455046] hub 2-1:1.0: USB hub found
[    2.455271] hub 2-1:1.0: 6 ports detected
[    2.526358] usb 1-1.2: new high-speed USB device number 3 using ehci_hcd
[    2.716224] usb 1-1.2: New USB device found, idVendor=5986, idProduct=02ac
[    2.716323] usb 1-1.2: New USB device strings: Mfr=3, Product=1, SerialNumber=2
[    2.716399] usb 1-1.2: Product: HP TrueVision HD
[    2.716458] usb 1-1.2: Manufacturer: HP TrueVision HD
[    2.716518] usb 1-1.2: SerialNumber: 0x0003
[    2.790213] usb 2-1.1: new low-speed USB device number 3 using ehci_hcd
[    2.886532] usb 2-1.1: New USB device found, idVendor=03f0, idProduct=8607
[    2.886633] usb 2-1.1: New USB device strings: Mfr=1, Product=2, SerialNumber=0
[    2.886710] usb 2-1.1: Product: HP Mobile USB Optical Mouse
[    2.886771] usb 2-1.1: Manufacturer: PixArt
[    2.891951] input: PixArt HP Mobile USB Optical Mouse as /devices/pci0000:00/0000:00:1d.0/usb2/2-1/2-1.1/2-1.1:1.0/input/input1
[    2.892196] generic-usb 0003:03F0:8607.0001: input,hidraw0: USB HID v1.11 Mouse [PixArt HP Mobile USB Optical Mouse] on usb-0000:00:1d.0-1.1/input0
[    2.892295] usbcore: registered new interface driver usbhid
[    2.892353] usbhid: USB HID core driver
[    3.653540] PM: Starting manual resume from disk
[    3.653615] PM: Hibernation image partition 8:6 present
[    3.653617] PM: Looking for hibernation image.
[    3.678247] PM: Image not found (code -22)
[    3.678250] PM: Hibernation image not present or could not be loaded.
[    3.731352] kjournald starting.  Commit interval 5 seconds
[    3.731504] EXT3-fs (sda5): mounted filesystem with ordered data mode
[    6.048848] udevd[322]: starting version 175
[    7.164906] input: Lid Switch as /devices/LNXSYSTM:00/device:00/PNP0A08:00/device:02/PNP0C0D:00/input/input2
[    7.165938] ACPI: AC Adapter [AC] (on-line)
[    7.166965] ACPI: Lid Switch [LID]
[    7.198569] ACPI: Battery Slot [BAT0] (battery present)
[    7.198699] input: Power Button as /devices/LNXSYSTM:00/device:00/PNP0C0C:00/input/input3
[    7.198782] ACPI: Power Button [PWRB]
[    7.198876] hp_accel: laptop model unknown, using default axes configuration
[    7.198894] input: Power Button as /devices/LNXSYSTM:00/LNXPWRBN:00/input/input4
[    7.198897] ACPI: Power Button [PWRF]
[    7.327714] rts_pstor: module is from the staging directory, the quality is unknown, you have been warned.
[    7.328473] Initializing Realtek PCIE storage driver...
[    7.328563] rts_pstor 0000:13:00.0: PCI INT A -> GSI 18 (level, low) -> IRQ 18
[    7.328671] Resource length: 0x1000
[    7.328741] Original address: 0xc3400000, remapped address: 0xffffc90000c68000
[    7.330261] pci->irq = 18
[    7.330318] rtsx_acquire_irq: chip->msi_en = 0, pci->irq = 18
[    7.330404] rts_pstor 0000:13:00.0: setting latency timer to 64
[    7.378874] iTCO_vendor_support: vendor-support=0
[    7.386852] iTCO_wdt: Intel TCO WatchDog Timer Driver v1.07
[    7.386979] iTCO_wdt: Found a Cougar Point TCO device (Version=2, TCOBASE=0x0460)
[    7.387115] iTCO_wdt: initialized. heartbeat=30 sec (nowayout=0)
[    7.401735] i801_smbus 0000:00:1f.3: PCI INT C -> GSI 19 (level, low) -> IRQ 19
[    7.401817] ACPI: resource 0000:00:1f.3 [io  0x6040-0x605f] conflicts with ACPI region SMBI [io 0x6040-0x604f]
[    7.401898] ACPI: If an ACPI driver is available for this device, you should use it instead of the native driver
[    7.406391] input: PC Speaker as /devices/platform/pcspkr/input/input5
[    7.469705] [drm] Initialized drm 1.1.0 20060810
[    7.532901] scsi6 : SCSI emulation for PCI-Express Mass Storage devices
[    7.533057] rts_pstor: waiting for device to settle before scanning
[    7.869917] i915 0000:00:02.0: PCI INT A -> GSI 16 (level, low) -> IRQ 16
[    7.869986] i915 0000:00:02.0: setting latency timer to 64
[    7.869997] [drm:drm_pci_agp_init] *ERROR* Cannot initialize the agpgart module.
[    7.870078] BUG: unable to handle kernel paging request at 0000000000001990
[    7.870223] IP: [<ffffffffa02b82ee>] intel_fb_restore_mode+0x9/0x3f [i915]
[    7.870349] PGD 252ae2067 PUD 2554e8067 PMD 0 
[    7.870529] Oops: 0000 [#1] SMP 
[    7.870667] CPU 0 
[    7.870710] Modules linked in: i915(+) snd_seq snd_timer snd_seq_device crc8 snd drm_kms_helper soundcore drm snd_page_alloc pcspkr i2c_i801 iTCO_wdt iTCO_vendor_support i2c_algo_bit i2c_core rts_pstor(C) cordic evdev processor psmouse wmi(+) hp_accel(+) battery button video ac lis3lv02d input_polldev serio_raw power_supply ext3 jbd mbcache usbhid hid sr_mod cdrom sd_mod crc_t10dif ahci libahci libata scsi_mod r8169 thermal mii thermal_sys ehci_hcd usbcore usb_common [last unloaded: scsi_wait_scan]
[    7.873049] 
[    7.873102] Pid: 413, comm: modprobe Tainted: G         C   3.2.0-2-amd64 #1 Hewlett-Packard HP Pavilion dv6 Notebook PC/3581
[    7.873299] RIP: 0010:[<ffffffffa02b82ee>]  [<ffffffffa02b82ee>] intel_fb_restore_mode+0x9/0x3f [i915]
[    7.873436] RSP: 0018:ffff8802537ddcc8  EFLAGS: 00010246
[    7.873497] RAX: 0000000000000000 RBX: ffff880255d49800 RCX: ffffffffa0244c7b
[    7.873563] RDX: ffffffffa023f4f0 RSI: ffffffffa0244c60 RDI: ffff880255d49800
[    7.873627] RBP: 0000000000000000 R08: 0000000000000000 R09: 0000000000000000
[    7.873692] R10: 0000000000000001 R11: ffff880255d49800 R12: 00000000ffffffea
[    7.873757] R13: ffffffffa02c1540 R14: ffff880255d49800 R15: ffff880256881090
[    7.873822] FS:  00007f74e7130700(0000) GS:ffff88025fa00000(0000) knlGS:0000000000000000
[    7.873900] CS:  0010 DS: 0000 ES: 0000 CR0: 000000008005003b
[    7.873963] CR2: 0000000000001990 CR3: 0000000252ae6000 CR4: 00000000000406f0
[    7.874028] DR0: 0000000000000000 DR1: 0000000000000000 DR2: 0000000000000000
[    7.874094] DR3: 0000000000000000 DR6: 00000000ffff0ff0 DR7: 0000000000000400
[    7.874159] Process modprobe (pid: 413, threadinfo ffff8802537dc000, task ffff88025375d710)
[    7.874237] Stack:
[    7.874293]  ffff880255d49800 ffffffffa028d80d ffff880255d49800 ffff880255d49800
[    7.874530]  ffffffffa02d3000 ffffffffa022b7cd ffff880255d49800 ffff880255d49800
[    7.874768]  ffffffffa02d3000 00000000ffffffea ffffffffa02c1540 ffffffffa0230298
[    7.875005] Call Trace:
[    7.875074]  [<ffffffffa028d80d>] ? i915_driver_lastclose+0x27/0x57 [i915]
[    7.875143]  [<ffffffffa022b7cd>] ? drm_lastclose+0x40/0x28b [drm]
[    7.875211]  [<ffffffffa0230298>] ? drm_fill_in_dev+0x174/0x17c [drm]
[    7.875279]  [<ffffffffa0231fcd>] ? drm_get_pci_dev+0xbe/0x253 [drm]
[    7.875344]  [<ffffffff8107074d>] ? arch_local_irq_save+0x11/0x17
[    7.875410]  [<ffffffff811c3edb>] ? local_pci_probe+0x39/0x68
[    7.875474]  [<ffffffff811c4984>] ? pci_device_probe+0xcd/0xfa
[    7.875539]  [<ffffffff8124dbe9>] ? driver_probe_device+0xa8/0x138
[    7.875603]  [<ffffffff8124dcc8>] ? __driver_attach+0x4f/0x6f
[    7.875666]  [<ffffffff8124dc79>] ? driver_probe_device+0x138/0x138
[    7.875731]  [<ffffffff8124cf19>] ? bus_for_each_dev+0x44/0x78
[    7.875794]  [<ffffffff8124d581>] ? bus_add_driver+0xa2/0x1f2
[    7.875859]  [<ffffffffa02e1000>] ? 0xffffffffa02e0fff
[    7.875921]  [<ffffffff8124e0ed>] ? driver_register+0x8d/0xf5
[    7.875984]  [<ffffffffa02e1000>] ? 0xffffffffa02e0fff
[    7.876046]  [<ffffffff811c5163>] ? __pci_register_driver+0x4d/0xb6
[    7.876111]  [<ffffffffa02e1000>] ? 0xffffffffa02e0fff
[    7.876173]  [<ffffffff81002085>] ? do_one_initcall+0x75/0x12c
[    7.876237]  [<ffffffffa02e1000>] ? 0xffffffffa02e0fff
[    7.876301]  [<ffffffff81074ef1>] ? sys_init_module+0x10c/0x25b
[    7.876366]  [<ffffffff8134e012>] ? system_call_fastpath+0x16/0x1b
[    7.876430] Code: 19 00 00 00 00 00 00 5e 5b 5d 41 5c 41 5d c3 48 8b 87 48 03 00 00 48 8b b8 90 19 00 00 e9 fd 12 f2 ff 41 53 48 8b 87 48 03 00 00 <48> 8b b8 90 19 00 00 e8 4c 07 f2 ff 84 c0 74 23 41 5a 48 c7 c1 
[    7.879115] RIP  [<ffffffffa02b82ee>] intel_fb_restore_mode+0x9/0x3f [i915]
[    7.879234]  RSP <ffff8802537ddcc8>
[    7.879292] CR2: 0000000000001990
[    7.879375] ---[ end trace 86f44523cd5e53ff ]---
[    7.990059] cfg80211: Calling CRDA to update world regulatory domain
[    8.040195] psmouse serio1: synaptics: Touchpad model: 1, fw: 7.5, id: 0x1e0b1, caps: 0xd00073/0x240000/0xa0400
[    8.070944] [drm] radeon kernel modesetting enabled.
[    8.071018] VGA switcheroo: detected switching method \_SB_.PCI0.GFX0.ATPX handle
[    8.071141] radeon 0000:01:00.0: enabling device (0000 -> 0003)
[    8.071209] radeon 0000:01:00.0: PCI INT A -> GSI 16 (level, low) -> IRQ 16
[    8.071278] radeon 0000:01:00.0: setting latency timer to 64
[    8.088638] input: SynPS/2 Synaptics TouchPad as /devices/platform/i8042/serio1/input/input6
[    8.131786] lis3lv02d: 8 bits 3DC sensor found
[    8.531719] rts_pstor: device scan complete
[    8.531869] scsi 6:0:0:0: Direct-Access     Generic- xD/SD/M.S.       1.00 PQ: 0 ANSI: 0 CCS
[    8.531987] Bad LUN (0:1)
[    8.532130] Bad target number (1:0)
[    8.532269] Bad target number (2:0)
[    8.532410] Bad target number (3:0)
[    8.532549] Bad target number (4:0)
[    8.532687] Bad target number (5:0)
[    8.532785] Bad target number (6:0)
[    8.532879] Bad target number (7:0)
[    8.533210] sd 6:0:0:0: [sdb] Attached SCSI removable disk
[    8.563655] input: ST LIS3LV02DL Accelerometer as /devices/platform/lis3lv02d/input/input7
[    8.563990] Registered led device: hp::hddprotect
[    8.564063] hp_accel: driver loaded
[    8.564306] wmi: Mapper loaded
[    8.580939] brcmsmac 0000:0d:00.0: bus 13 slot 0 func 0 irq 3
[    8.581047] brcmsmac 0000:0d:00.0: PCI INT A -> GSI 17 (level, low) -> IRQ 17
[    8.581118] brcmsmac 0000:0d:00.0: setting latency timer to 64
[    8.740976] input: HP WMI hotkeys as /devices/virtual/input/input8
[    8.748472] Linux media interface: v0.10
[    8.750565] Linux video capture interface: v2.00
[    8.784610] uvcvideo: Found UVC 1.00 device HP TrueVision HD (5986:02ac)
[    8.791840] input: HP TrueVision HD as /devices/pci0000:00/0000:00:1a.0/usb1/1-1/1-1.2/1-1.2:1.0/input/input9
[    8.792003] usbcore: registered new interface driver uvcvideo
[    8.792064] USB Video Class driver (1.1.1)
[    9.086704] ieee80211 phy0: Selected rate control algorithm 'minstrel_ht'
[    9.610151] cfg80211: World regulatory domain updated:
[    9.610217] cfg80211:     (start_freq - end_freq @ bandwidth), (max_antenna_gain, max_eirp)
[    9.610299] cfg80211:     (2402000 KHz - 2472000 KHz @ 40000 KHz), (300 mBi, 2000 mBm)
[    9.610388] cfg80211:     (2457000 KHz - 2482000 KHz @ 20000 KHz), (300 mBi, 2000 mBm)
[    9.610466] cfg80211:     (2474000 KHz - 2494000 KHz @ 20000 KHz), (300 mBi, 2000 mBm)
[    9.610544] cfg80211:     (5170000 KHz - 5250000 KHz @ 40000 KHz), (300 mBi, 2000 mBm)
[    9.610623] cfg80211:     (5735000 KHz - 5835000 KHz @ 40000 KHz), (300 mBi, 2000 mBm)
[    9.610885] cfg80211: Calling CRDA for country: US
[    9.614242] cfg80211: Regulatory domain changed to country: US
[    9.614305] cfg80211:     (start_freq - end_freq @ bandwidth), (max_antenna_gain, max_eirp)
[    9.614393] cfg80211:     (2402000 KHz - 2472000 KHz @ 40000 KHz), (300 mBi, 2700 mBm)
[    9.614471] cfg80211:     (5170000 KHz - 5250000 KHz @ 40000 KHz), (300 mBi, 1700 mBm)
[    9.614550] cfg80211:     (5250000 KHz - 5330000 KHz @ 40000 KHz), (300 mBi, 2000 mBm)
[    9.614626] cfg80211:     (5490000 KHz - 5600000 KHz @ 40000 KHz), (300 mBi, 2000 mBm)
[    9.614703] cfg80211:     (5650000 KHz - 5710000 KHz @ 40000 KHz), (300 mBi, 2000 mBm)
[    9.614781] cfg80211:     (5735000 KHz - 5835000 KHz @ 40000 KHz), (300 mBi, 3000 mBm)
[   22.707655] Adding 15907836k swap on /dev/sda6.  Priority:-1 extents:1 across:15907836k 
[   22.919135] EXT3-fs (sda5): using internal journal
[   23.084306] device-mapper: uevent: version 1.0.3
[   23.084502] device-mapper: ioctl: 4.22.0-ioctl (2011-10-19) initialised: dm-devel@redhat.com
[   23.287845] loop: module loaded
[   24.419937] fuse init (API version 7.17)
[   62.894445] usb 2-1.1: USB disconnect, device number 3
[   64.370334] usb 2-1.1: new low-speed USB device number 4 using ehci_hcd
[   64.467033] usb 2-1.1: New USB device found, idVendor=03f0, idProduct=8607
[   64.467120] usb 2-1.1: New USB device strings: Mfr=1, Product=2, SerialNumber=0
[   64.467195] usb 2-1.1: Product: HP Mobile USB Optical Mouse
[   64.467256] usb 2-1.1: Manufacturer: PixArt
[   64.470204] input: PixArt HP Mobile USB Optical Mouse as /devices/pci0000:00/0000:00:1d.0/usb2/2-1/2-1.1/2-1.1:1.0/input/input10
[   64.470631] generic-usb 0003:03F0:8607.0002: input,hidraw0: USB HID v1.11 Mouse [PixArt HP Mobile USB Optical Mouse] on usb-0000:00:1d.0-1.1/input0



** Model information
sys_vendor: Hewlett-Packard
product_name: HP Pavilion dv6 Notebook PC
product_version: 058F110000244610000620100
chassis_vendor: Hewlett-Packard
chassis_version: Chassis Version
bios_vendor: Hewlett-Packard
bios_version: F.1A
board_vendor: Hewlett-Packard
board_name: 3581
board_version: 10.31

** Network interface configuration:

auto lo
iface lo inet loopback

allow-hotplug eth0

** PCI devices:
00:00.0 Host bridge [0600]: Intel Corporation 2nd Generation Core Processor Family DRAM Controller [8086:0104] (rev 09)
	Subsystem: Hewlett-Packard Company Device [103c:3581]
	Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
	Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort+ >SERR- <PERR- INTx-
	Latency: 0
	Capabilities: <access denied>
	Kernel driver in use: agpgart-intel

00:01.0 PCI bridge [0604]: Intel Corporation Xeon E3-1200/2nd Generation Core Processor Family PCI Express Root Port [8086:0101] (rev 09) (prog-if 00 [Normal decode])
	Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx+
	Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
	Latency: 0, Cache Line Size: 64 bytes
	Bus: primary=00, secondary=01, subordinate=06, sec-latency=0
	I/O behind bridge: 00005000-00005fff
	Memory behind bridge: c6400000-c73fffff
	Prefetchable memory behind bridge: 00000000a0000000-00000000afffffff
	Secondary status: 66MHz- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- <SERR- <PERR-
	BridgeCtl: Parity- SERR- NoISA- VGA- MAbort- >Reset- FastB2B-
		PriDiscTmr- SecDiscTmr- DiscTmrStat- DiscTmrSERREn-
	Capabilities: <access denied>
	Kernel driver in use: pcieport

00:02.0 VGA compatible controller [0300]: Intel Corporation 2nd Generation Core Processor Family Integrated Graphics Controller [8086:0116] (rev 09) (prog-if 00 [VGA controller])
	Subsystem: Hewlett-Packard Company Device [103c:3581]
	Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx+
	Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
	Latency: 0
	Interrupt: pin A routed to IRQ 44
	Region 0: Memory at c0000000 (64-bit, non-prefetchable) [size=4M]
	Region 2: Memory at b0000000 (64-bit, prefetchable) [size=256M]
	Region 4: I/O ports at 6000 [size=64]
	Expansion ROM at <unassigned> [disabled]
	Capabilities: <access denied>
	Kernel driver in use: i915

00:16.0 Communication controller [0780]: Intel Corporation 6 Series/C200 Series Chipset Family MEI Controller #1 [8086:1c3a] (rev 04)
	Subsystem: Hewlett-Packard Company Device [103c:3581]
	Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
	Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
	Latency: 0
	Interrupt: pin A routed to IRQ 3
	Region 0: Memory at c7404000 (64-bit, non-prefetchable) [size=16]
	Capabilities: <access denied>

00:1a.0 USB controller [0c03]: Intel Corporation 6 Series/C200 Series Chipset Family USB Enhanced Host Controller #2 [8086:1c2d] (rev 05) (prog-if 20 [EHCI])
	Subsystem: Hewlett-Packard Company Device [103c:3581]
	Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
	Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
	Latency: 0
	Interrupt: pin A routed to IRQ 16
	Region 0: Memory at c740a000 (32-bit, non-prefetchable) [size=1K]
	Capabilities: <access denied>
	Kernel driver in use: ehci_hcd

00:1b.0 Audio device [0403]: Intel Corporation 6 Series/C200 Series Chipset Family High Definition Audio Controller [8086:1c20] (rev 05)
	Subsystem: Hewlett-Packard Company Device [103c:3581]
	Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx+
	Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
	Latency: 0, Cache Line Size: 64 bytes
	Interrupt: pin A routed to IRQ 45
	Region 0: Memory at c7400000 (64-bit, non-prefetchable) [size=16K]
	Capabilities: <access denied>
	Kernel driver in use: snd_hda_intel

00:1c.0 PCI bridge [0604]: Intel Corporation 6 Series/C200 Series Chipset Family PCI Express Root Port 1 [8086:1c10] (rev b5) (prog-if 00 [Normal decode])
	Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
	Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
	Latency: 0, Cache Line Size: 64 bytes
	Bus: primary=00, secondary=07, subordinate=0c, sec-latency=0
	I/O behind bridge: 00004000-00004fff
	Memory behind bridge: c5400000-c63fffff
	Prefetchable memory behind bridge: 00000000c0400000-00000000c13fffff
	Secondary status: 66MHz- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- <SERR- <PERR-
	BridgeCtl: Parity- SERR- NoISA- VGA- MAbort- >Reset- FastB2B-
		PriDiscTmr- SecDiscTmr- DiscTmrStat- DiscTmrSERREn-
	Capabilities: <access denied>
	Kernel driver in use: pcieport

00:1c.1 PCI bridge [0604]: Intel Corporation 6 Series/C200 Series Chipset Family PCI Express Root Port 2 [8086:1c12] (rev b5) (prog-if 00 [Normal decode])
	Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
	Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
	Latency: 0, Cache Line Size: 64 bytes
	Bus: primary=00, secondary=0d, subordinate=12, sec-latency=0
	I/O behind bridge: 00003000-00003fff
	Memory behind bridge: c4400000-c53fffff
	Prefetchable memory behind bridge: 00000000c1400000-00000000c23fffff
	Secondary status: 66MHz- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- <SERR- <PERR-
	BridgeCtl: Parity- SERR- NoISA- VGA- MAbort- >Reset- FastB2B-
		PriDiscTmr- SecDiscTmr- DiscTmrStat- DiscTmrSERREn-
	Capabilities: <access denied>
	Kernel driver in use: pcieport

00:1c.2 PCI bridge [0604]: Intel Corporation 6 Series/C200 Series Chipset Family PCI Express Root Port 3 [8086:1c14] (rev b5) (prog-if 00 [Normal decode])
	Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
	Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
	Latency: 0, Cache Line Size: 64 bytes
	Bus: primary=00, secondary=13, subordinate=18, sec-latency=0
	I/O behind bridge: 00002000-00002fff
	Memory behind bridge: c3400000-c43fffff
	Prefetchable memory behind bridge: 00000000c2400000-00000000c33fffff
	Secondary status: 66MHz- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- <SERR- <PERR-
	BridgeCtl: Parity- SERR- NoISA- VGA- MAbort- >Reset- FastB2B-
		PriDiscTmr- SecDiscTmr- DiscTmrStat- DiscTmrSERREn-
	Capabilities: <access denied>
	Kernel driver in use: pcieport

00:1d.0 USB controller [0c03]: Intel Corporation 6 Series/C200 Series Chipset Family USB Enhanced Host Controller #1 [8086:1c26] (rev 05) (prog-if 20 [EHCI])
	Subsystem: Hewlett-Packard Company Device [103c:3581]
	Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
	Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
	Latency: 0
	Interrupt: pin A routed to IRQ 20
	Region 0: Memory at c7409000 (32-bit, non-prefetchable) [size=1K]
	Capabilities: <access denied>
	Kernel driver in use: ehci_hcd

00:1f.0 ISA bridge [0601]: Intel Corporation HM65 Express Chipset Family LPC Controller [8086:1c49] (rev 05)
	Subsystem: Hewlett-Packard Company Device [103c:3581]
	Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
	Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
	Latency: 0
	Capabilities: <access denied>

00:1f.2 SATA controller [0106]: Intel Corporation 6 Series/C200 Series Chipset Family 6 port SATA AHCI Controller [8086:1c03] (rev 05) (prog-if 01 [AHCI 1.0])
	Subsystem: Hewlett-Packard Company Device [103c:3581]
	Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx+
	Status: Cap+ 66MHz+ UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
	Latency: 0
	Interrupt: pin B routed to IRQ 42
	Region 0: I/O ports at 6098 [size=8]
	Region 1: I/O ports at 60bc [size=4]
	Region 2: I/O ports at 6090 [size=8]
	Region 3: I/O ports at 60b8 [size=4]
	Region 4: I/O ports at 6060 [size=32]
	Region 5: Memory at c7408000 (32-bit, non-prefetchable) [size=2K]
	Capabilities: <access denied>
	Kernel driver in use: ahci

00:1f.3 SMBus [0c05]: Intel Corporation 6 Series/C200 Series Chipset Family SMBus Controller [8086:1c22] (rev 05)
	Subsystem: Hewlett-Packard Company Device [103c:3581]
	Control: I/O+ Mem+ BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
	Status: Cap- 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
	Interrupt: pin C routed to IRQ 19
	Region 0: Memory at c7406000 (64-bit, non-prefetchable) [size=256]
	Region 4: I/O ports at 6040 [size=32]

01:00.0 VGA compatible controller [0300]: ATI Technologies Inc Seymour [Radeon HD 6400M Series] [1002:6760] (prog-if 00 [VGA controller])
	Subsystem: Hewlett-Packard Company Device [103c:3581]
	Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx+
	Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
	Latency: 0, Cache Line Size: 64 bytes
	Interrupt: pin A routed to IRQ 43
	Region 0: Memory at a0000000 (64-bit, prefetchable) [size=256M]
	Region 2: Memory at c6400000 (64-bit, non-prefetchable) [size=128K]
	Region 4: I/O ports at 5000 [size=256]
	Expansion ROM at c6420000 [disabled] [size=128K]
	Capabilities: <access denied>
	Kernel driver in use: radeon

07:00.0 Ethernet controller [0200]: Realtek Semiconductor Co., Ltd. RTL8111/8168B PCI Express Gigabit Ethernet controller [10ec:8168] (rev 06)
	Subsystem: Hewlett-Packard Company Device [103c:3581]
	Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx+
	Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
	Latency: 0, Cache Line Size: 64 bytes
	Interrupt: pin A routed to IRQ 41
	Region 0: I/O ports at 4000 [size=256]
	Region 2: Memory at c0404000 (64-bit, prefetchable) [size=4K]
	Region 4: Memory at c0400000 (64-bit, prefetchable) [size=16K]
	Capabilities: <access denied>
	Kernel driver in use: r8169

0d:00.0 Network controller [0280]: Broadcom Corporation BCM4313 802.11b/g/n Wireless LAN Controller [14e4:4727] (rev 01)
	Subsystem: Hewlett-Packard Company Device [103c:145c]
	Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
	Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
	Latency: 0, Cache Line Size: 64 bytes
	Interrupt: pin A routed to IRQ 17
	Region 0: Memory at c4400000 (64-bit, non-prefetchable) [size=16K]
	Capabilities: <access denied>
	Kernel driver in use: brcmsmac

13:00.0 Unassigned class [ff00]: Realtek Semiconductor Co., Ltd. RTS5116 PCI Express Card Reader [10ec:5209] (rev 01)
	Subsystem: Hewlett-Packard Company Device [103c:3581]
	Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
	Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
	Latency: 0, Cache Line Size: 64 bytes
	Interrupt: pin A routed to IRQ 18
	Region 0: Memory at c3400000 (32-bit, non-prefetchable) [size=4K]
	Expansion ROM at c2400000 [disabled] [size=64K]
	Capabilities: <access denied>
	Kernel driver in use: rts_pstor


** USB devices:
Bus 001 Device 001: ID 1d6b:0002 Linux Foundation 2.0 root hub
Bus 002 Device 001: ID 1d6b:0002 Linux Foundation 2.0 root hub
Bus 001 Device 002: ID 8087:0024 Intel Corp. Integrated Rate Matching Hub
Bus 002 Device 002: ID 8087:0024 Intel Corp. Integrated Rate Matching Hub
Bus 001 Device 003: ID 5986:02ac Acer, Inc 
Bus 002 Device 015: ID 03f0:8607 Hewlett-Packard 


-- System Information:
Debian Release: wheezy/sid
  APT prefers stable-updates
  APT policy: (500, 'stable-updates'), (500, 'testing'), (500, 'stable')
Architecture: amd64 (x86_64)

Kernel: Linux 3.2.0-1-amd64 (SMP w/8 CPU cores)
Locale: LANG=en_GB.utf8, LC_CTYPE=en_GB.utf8 (charmap=UTF-8)
Shell: /bin/sh linked to /bin/dash

Versions of packages linux-image-3.2.0-2-amd64 depends on:
ii  debconf [debconf-2.0]                   1.5.41
ii  initramfs-tools [linux-initramfs-tool]  0.101
ii  linux-base                              3.5
ii  module-init-tools                       3.16-1

Versions of packages linux-image-3.2.0-2-amd64 recommends:
ii  firmware-linux-free  3

Versions of packages linux-image-3.2.0-2-amd64 suggests:
pn  grub-pc        1.99-17
pn  linux-doc-3.2  <none>

Versions of packages linux-image-3.2.0-2-amd64 is related to:
pn  firmware-atheros        <none>
pn  firmware-bnx2           <none>
pn  firmware-bnx2x          <none>
pn  firmware-brcm80211      0.35
pn  firmware-intelwimax     <none>
pn  firmware-ipw2x00        <none>
pn  firmware-ivtv           <none>
pn  firmware-iwlwifi        0.35
pn  firmware-libertas       <none>
pn  firmware-linux          <none>
pn  firmware-linux-nonfree  0.35
pn  firmware-myricom        <none>
pn  firmware-netxen         <none>
pn  firmware-qlogic         <none>
pn  firmware-ralink         <none>
pn  firmware-realtek        <none>
pn  xen-hypervisor          <none>

-- debconf information:
  linux-image-3.2.0-2-amd64/postinst/ignoring-ramdisk:
  linux-image-3.2.0-2-amd64/postinst/depmod-error-initrd-3.2.0-2-amd64: false
  linux-image-3.2.0-2-amd64/postinst/missing-firmware-3.2.0-2-amd64:
  linux-image-3.2.0-2-amd64/prerm/removing-running-kernel-3.2.0-2-amd64: true



Reply to: