Package: linux-2.6
Version: 3.1.8-2
Severity: important
Dear Maintainer,
This machine is a Zotac ZBOX AD10, with AMD E-350 processor and AMD M1
chipset.
I installed Debian Squeeze 6.0.4, and the free ATI driver worked fine
to get full resolution graphics on the display.
Upgrading from Squeeze to Wheezy brings in the Linux 3.1.0 kernel. Now
the free ATI driver corrups display output: a mess of snow covers
approximately the top half of the screen, and the bottom part is black.
Installing the ‘firmware-linux-nonfree’ package fixes display again to
the point where graphics are visible in the correct resolution. I have
uninstalled that package, and the display corruption returns.
This is a regression: display with the free ATI driver should be at
least as good as was in the 2.6 kernel from Squeeze.
Please feel free to re-assign this if I have reported to the wrong
package.
-- Package-specific info:
** Version:
Linux version 3.1.0-1-amd64 (Debian 3.1.8-2) (ben@decadent.org.uk) (gcc version 4.6.2 (Debian 4.6.2-11) ) #1 SMP Tue Jan 10 05:01:58 UTC 2012
** Command line:
BOOT_IMAGE=/vmlinuz-3.1.0-1-amd64 root=/dev/mapper/anemone-root ro quiet
** Not tainted
** Kernel log:
[ 7.225595] [drm] DDC: 0x6430 0x6430 0x6434 0x6434 0x6438 0x6438 0x643c 0x643c
[ 7.225599] [drm] Encoders:
[ 7.225601] [drm] DFP1: INTERNAL_UNIPHY
[ 7.225604] [drm] Connector 1:
[ 7.225607] [drm] HDMI-A
[ 7.225609] [drm] HPD2
[ 7.225613] [drm] DDC: 0x6440 0x6440 0x6444 0x6444 0x6448 0x6448 0x644c 0x644c
[ 7.225616] [drm] Encoders:
[ 7.225618] [drm] DFP2: INTERNAL_UNIPHY
[ 7.225621] [drm] Connector 2:
[ 7.225623] [drm] VGA
[ 7.225627] [drm] DDC: 0x64d8 0x64d8 0x64dc 0x64dc 0x64e0 0x64e0 0x64e4 0x64e4
[ 7.225630] [drm] Encoders:
[ 7.225632] [drm] CRT1: INTERNAL_KLDSCP_DAC1
[ 7.622130] ath9k 0000:03:00.0: PCI INT A -> GSI 16 (level, low) -> IRQ 16
[ 7.622150] ath9k 0000:03:00.0: setting latency timer to 64
[ 7.675216] ath: EEPROM regdomain: 0x60
[ 7.675223] ath: EEPROM indicates we should expect a direct regpair map
[ 7.675231] ath: Country alpha2 being used: 00
[ 7.675234] ath: Regpair used: 0x60
[ 7.704046] [drm] Radeon display connector DP-1: No monitor connected or invalid EDID
[ 7.809976] [drm] Radeon display connector HDMI-A-1: Found valid EDID
[ 8.288037] [drm] Radeon display connector VGA-1: No monitor connected or invalid EDID
[ 8.288079] [drm] Internal thermal controller without fan control
[ 8.288193] [drm] radeon: power management initialized
[ 8.512790] ieee80211 phy0: Selected rate control algorithm 'ath9k_rate_control'
[ 8.513779] Registered led device: ath9k-phy0
[ 8.513797] ieee80211 phy0: Atheros AR9285 Rev:2 mem=0xffffc900110e0000, irq=16
[ 8.522648] [drm] fb mappable at 0xB0040000
[ 8.522654] [drm] vram apper at 0xB0000000
[ 8.522657] [drm] size 5787648
[ 8.522660] [drm] fb depth is 24
[ 8.522663] [drm] pitch is 6400
[ 8.528205] fbcon: radeondrmfb (fb0) is primary device
[ 8.577156] Console: switching to colour frame buffer device 200x56
[ 8.585357] fb0: radeondrmfb frame buffer device
[ 8.585361] drm: registered panic notifier
[ 8.585375] [drm] Initialized radeon 2.11.0 20080528 for 0000:00:01.0 on minor 0
[ 8.954991] input: USB OPTICAL MOUSE as /devices/pci0000:00/0000:00:12.0/usb4/4-2/4-2.1/4-2.1:1.0/input/input5
[ 8.955791] generic-usb 0003:15D9:0A4C.0001: input,hidraw0: USB HID v1.11 Mouse [ USB OPTICAL MOUSE] on usb-0000:00:12.0-2.1/input0
[ 8.960871] input: Mitsumi Electric Apple Extended USB Keyboard as /devices/pci0000:00/0000:00:12.0/usb4/4-2/4-2.3/4-2.3:1.0/input/input6
[ 8.961456] generic-usb 0003:05AC:020B.0002: input,hidraw1: USB HID v1.10 Keyboard [Mitsumi Electric Apple Extended USB Keyboard] on usb-0000:00:12.0-2.3/input0
[ 8.970771] input: Mitsumi Electric Apple Extended USB Keyboard as /devices/pci0000:00/0000:00:12.0/usb4/4-2/4-2.3/4-2.3:1.1/input/input7
[ 8.971335] generic-usb 0003:05AC:020B.0003: input,hidraw2: USB HID v1.10 Device [Mitsumi Electric Apple Extended USB Keyboard] on usb-0000:00:12.0-2.3/input1
[ 8.971383] usbcore: registered new interface driver usbhid
[ 8.971387] usbhid: USB HID core driver
[ 9.043896] snd_hda_intel 0000:00:01.1: PCI INT B -> GSI 19 (level, low) -> IRQ 19
[ 9.043990] snd_hda_intel 0000:00:01.1: irq 44 for MSI/MSI-X
[ 9.044059] snd_hda_intel 0000:00:01.1: setting latency timer to 64
[ 9.096507] Bluetooth: Core ver 2.16
[ 9.096556] NET: Registered protocol family 31
[ 9.096560] Bluetooth: HCI device and connection manager initialized
[ 9.096566] Bluetooth: HCI socket layer initialized
[ 9.096570] Bluetooth: L2CAP socket layer initialized
[ 9.096585] Bluetooth: SCO socket layer initialized
[ 9.118785] Bluetooth: Atheros AR30xx firmware driver ver 1.0
[ 9.123909] Bluetooth: Error loading firmware
[ 9.123984] ath3k: probe of 7-3:1.0 failed with error -5
[ 9.124063] usbcore: registered new interface driver ath3k
[ 9.154921] HDMI status: Codec=0 Pin=3 Presence_Detect=0 ELD_Valid=0
[ 9.155559] input: HD-Audio Generic HDMI/DP as /devices/pci0000:00/0000:00:01.1/sound/card0/input8
[ 9.156277] snd_hda_intel 0000:00:14.2: PCI INT A -> GSI 16 (level, low) -> IRQ 16
[ 9.409273] cfg80211: World regulatory domain updated:
[ 9.409282] cfg80211: (start_freq - end_freq @ bandwidth), (max_antenna_gain, max_eirp)
[ 9.409288] cfg80211: (2402000 KHz - 2472000 KHz @ 40000 KHz), (300 mBi, 2000 mBm)
[ 9.409294] cfg80211: (2457000 KHz - 2482000 KHz @ 20000 KHz), (300 mBi, 2000 mBm)
[ 9.409299] cfg80211: (2474000 KHz - 2494000 KHz @ 20000 KHz), (300 mBi, 2000 mBm)
[ 9.409303] cfg80211: (5170000 KHz - 5250000 KHz @ 40000 KHz), (300 mBi, 2000 mBm)
[ 9.409308] cfg80211: (5735000 KHz - 5835000 KHz @ 40000 KHz), (300 mBi, 2000 mBm)
[ 9.432187] hda_codec: ALC892: BIOS auto-probing.
[ 11.540332] EXT3-fs (dm-0): using internal journal
[ 11.896606] loop: module loaded
[ 12.263527] Adding 7135228k swap on /dev/mapper/anemone-swap_1. Priority:-1 extents:1 across:7135228k
[ 13.898240] r8169 0000:06:00.0: eth0: unable to load firmware patch rtl_nic/rtl8168e-2.fw (-2)
[ 13.923900] r8169 0000:06:00.0: eth0: link down
[ 13.923917] r8169 0000:06:00.0: eth0: link down
[ 13.924854] ADDRCONF(NETDEV_UP): eth0: link is not ready
[ 14.110129] RPC: Registered named UNIX socket transport module.
[ 14.110136] RPC: Registered udp transport module.
[ 14.110140] RPC: Registered tcp transport module.
[ 14.110143] RPC: Registered tcp NFSv4.1 backchannel transport module.
[ 14.137107] FS-Cache: Loaded
[ 14.186040] FS-Cache: Netfs 'nfs' registered for caching
[ 14.315058] Installing knfsd (copyright (C) 1996 okir@monad.swb.de).
[ 15.580753] fuse init (API version 7.17)
[ 15.636397] r8169 0000:06:00.0: eth0: link up
[ 15.637328] ADDRCONF(NETDEV_CHANGE): eth0: link becomes ready
[ 22.717769] ADDRCONF(NETDEV_UP): wlan0: link is not ready
[ 25.845391] Bluetooth: RFCOMM TTY layer initialized
[ 25.845402] Bluetooth: RFCOMM socket layer initialized
[ 25.845406] Bluetooth: RFCOMM ver 1.11
[ 25.894978] Bluetooth: BNEP (Ethernet Emulation) ver 1.3
[ 25.894986] Bluetooth: BNEP filters: protocol multicast
[ 26.456227] eth0: no IPv6 routers present
[ 26.629494] lp: driver loaded but no devices found
[ 26.748126] ppdev: user-space parallel port driver
[ 29.374813] powernow-k8: Found 1 AMD E-350 Processor (2 cpu cores) (version 2.20.00)
[ 29.374901] powernow-k8: 0 : pstate 0 (1600 MHz)
[ 29.374905] powernow-k8: 1 : pstate 1 (1280 MHz)
[ 29.374909] powernow-k8: 2 : pstate 2 (800 MHz)
** Model information
sys_vendor:
product_name:
product_version:
chassis_vendor:
chassis_version:
bios_vendor: American Megatrends Inc.
bios_version: 4.6.4
board_vendor: ZOTAC
board_name: AMD HUDSON-M1
board_version:
** Loaded modules:
powernow_k8
mperf
cpufreq_userspace
cpufreq_stats
cpufreq_conservative
cpufreq_powersave
parport_pc
ppdev
lp
parport
bnep
rfcomm
binfmt_misc
fuse
nfsd
nfs
lockd
fscache
auth_rpcgss
nfs_acl
sunrpc
ext2
loop
snd_hda_codec_realtek
snd_hda_codec_hdmi
ath3k
bluetooth
snd_hda_intel
snd_hda_codec
usbhid
hid
crc16
arc4
snd_hwdep
snd_pcm
ath9k
mac80211
ath9k_common
ath9k_hw
ath
cfg80211
snd_seq
snd_timer
ir_lirc_codec
lirc_dev
radeon
snd_seq_device
ir_mce_kbd_decoder
ir_sony_decoder
sp5100_tco
ir_jvc_decoder
i2c_piix4
ir_rc6_decoder
snd
soundcore
ir_rc5_decoder
snd_page_alloc
rfkill
ir_nec_decoder
rc_rc6_mce
pcspkr
k10temp
ttm
drm_kms_helper
evdev
psmouse
drm
ite_cir
rc_core
i2c_algo_bit
i2c_core
serio_raw
processor
button
power_supply
thermal_sys
ext3
jbd
mbcache
dm_mod
sd_mod
crc_t10dif
ata_generic
xhci_hcd
ohci_hcd
r8169
mii
ahci
pata_atiixp
libahci
libata
ehci_hcd
scsi_mod
usbcore
** Network interface configuration:
# This file describes the network interfaces available on your system
# and how to activate them. For more information, see interfaces(5).
# The loopback network interface
auto lo
iface lo inet loopback
# The primary network interface
allow-hotplug eth0
iface eth0 inet dhcp
** Network status:
*** IP interfaces and addresses:
1: lo: <LOOPBACK,UP,LOWER_UP> mtu 16436 qdisc noqueue state UNKNOWN
link/loopback 00:00:00:00:00:00 brd 00:00:00:00:00:00
inet 127.0.0.1/8 scope host lo
inet6 ::1/128 scope host
valid_lft forever preferred_lft forever
2: eth0: <BROADCAST,MULTICAST,UP,LOWER_UP> mtu 1500 qdisc pfifo_fast state UP qlen 1000
link/ether 00:01:2e:3a:e6:4e brd ff:ff:ff:ff:ff:ff
inet 192.168.5.14/24 brd 192.168.5.255 scope global eth0
inet6 fe80::201:2eff:fe3a:e64e/64 scope link
valid_lft forever preferred_lft forever
3: wlan0: <NO-CARRIER,BROADCAST,MULTICAST,UP> mtu 1500 qdisc mq state DOWN qlen 1000
link/ether 74:2f:68:af:ce:37 brd ff:ff:ff:ff:ff:ff
*** Device statistics:
Inter-| Receive | Transmit
face |bytes packets errs drop fifo frame compressed multicast|bytes packets errs drop fifo colls carrier compressed
lo: 8264 128 0 0 0 0 0 0 8264 128 0 0 0 0 0 0
eth0: 178866 811 0 0 0 0 0 0 151977 963 0 0 0 0 0 0
wlan0: 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
*** Protocol statistics:
Ip:
951 total packets received
2 with invalid addresses
0 forwarded
0 incoming packets discarded
949 incoming packets delivered
1052 requests sent out
Icmp:
0 ICMP messages received
0 input ICMP message failed.
ICMP input histogram:
0 ICMP messages sent
0 ICMP messages failed
ICMP output histogram:
Tcp:
87 active connections openings
14 passive connection openings
0 failed connection attempts
0 connection resets received
3 connections established
855 segments received
962 segments send out
0 segments retransmited
0 bad segments received.
2 resets sent
Udp:
84 packets received
0 packets to unknown port received.
0 packet receive errors
87 packets sent
UdpLite:
TcpExt:
84 TCP sockets finished time wait in fast timer
24 delayed acks sent
2 packets directly queued to recvmsg prequeue.
172 packet headers predicted
171 acknowledgments not containing data payload received
124 predicted acknowledgments
IpExt:
InMcastPkts: 20
OutMcastPkts: 23
InBcastPkts: 14
OutBcastPkts: 8
InOctets: 178981
OutOctets: 141752
InMcastOctets: 3519
OutMcastOctets: 3647
InBcastOctets: 1418
OutBcastOctets: 464
** PCI devices:
00:00.0 Host bridge [0600]: Advanced Micro Devices [AMD] Family 14h Processor Root Complex [1022:1510]
Subsystem: Advanced Micro Devices [AMD] Family 14h Processor Root Complex [1022:1510]
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap- 66MHz+ UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 32
00:01.0 VGA compatible controller [0300]: ATI Technologies Inc Wrestler [Radeon HD 6310] [1002:9802] (prog-if 00 [VGA controller])
Subsystem: ZOTAC International (MCO) Ltd. Device [19da:a191]
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0, Cache Line Size: 64 bytes
Interrupt: pin A routed to IRQ 18
Region 0: Memory at b0000000 (32-bit, prefetchable) [size=256M]
Region 1: I/O ports at f000 [size=256]
Region 2: Memory at feb00000 (32-bit, non-prefetchable) [size=256K]
Expansion ROM at <unassigned> [disabled]
Capabilities: <access denied>
Kernel driver in use: radeon
00:01.1 Audio device [0403]: ATI Technologies Inc Wrestler HDMI Audio [Radeon HD 6250/6310] [1002:1314]
Subsystem: ZOTAC International (MCO) Ltd. Device [19da:a191]
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx+
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0, Cache Line Size: 64 bytes
Interrupt: pin B routed to IRQ 44
Region 0: Memory at feb44000 (32-bit, non-prefetchable) [size=16K]
Capabilities: <access denied>
Kernel driver in use: snd_hda_intel
00:04.0 PCI bridge [0604]: Advanced Micro Devices [AMD] Family 14h Processor Root Port [1022:1512] (prog-if 00 [Normal decode])
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0, Cache Line Size: 64 bytes
Bus: primary=00, secondary=01, subordinate=01, sec-latency=0
I/O behind bridge: 00001000-00001fff
Memory behind bridge: fea00000-feafffff
Prefetchable memory behind bridge: 00000000d0100000-00000000d02fffff
Secondary status: 66MHz- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- <SERR- <PERR-
BridgeCtl: Parity- SERR- NoISA- VGA- MAbort- >Reset- FastB2B-
PriDiscTmr- SecDiscTmr- DiscTmrStat- DiscTmrSERREn-
Capabilities: <access denied>
Kernel driver in use: pcieport
00:11.0 SATA controller [0106]: ATI Technologies Inc SB7x0/SB8x0/SB9x0 SATA Controller [IDE mode] [1002:4390] (rev 40) (prog-if 01 [AHCI 1.0])
Subsystem: ZOTAC International (MCO) Ltd. Device [19da:a191]
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz+ UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 32
Interrupt: pin A routed to IRQ 19
Region 0: I/O ports at f190 [size=8]
Region 1: I/O ports at f180 [size=4]
Region 2: I/O ports at f170 [size=8]
Region 3: I/O ports at f160 [size=4]
Region 4: I/O ports at f150 [size=16]
Region 5: Memory at feb4f000 (32-bit, non-prefetchable) [size=1K]
Capabilities: <access denied>
Kernel driver in use: ahci
00:12.0 USB controller [0c03]: ATI Technologies Inc SB7x0/SB8x0/SB9x0 USB OHCI0 Controller [1002:4397] (prog-if 10 [OHCI])
Subsystem: ZOTAC International (MCO) Ltd. Device [19da:a191]
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap- 66MHz+ UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 32, Cache Line Size: 64 bytes
Interrupt: pin A routed to IRQ 18
Region 0: Memory at feb4e000 (32-bit, non-prefetchable) [size=4K]
Kernel driver in use: ohci_hcd
00:12.2 USB controller [0c03]: ATI Technologies Inc SB7x0/SB8x0/SB9x0 USB EHCI Controller [1002:4396] (prog-if 20 [EHCI])
Subsystem: ZOTAC International (MCO) Ltd. Device [19da:a191]
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV+ VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz+ UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 32, Cache Line Size: 64 bytes
Interrupt: pin B routed to IRQ 17
Region 0: Memory at feb4d000 (32-bit, non-prefetchable) [size=256]
Capabilities: <access denied>
Kernel driver in use: ehci_hcd
00:13.0 USB controller [0c03]: ATI Technologies Inc SB7x0/SB8x0/SB9x0 USB OHCI0 Controller [1002:4397] (prog-if 10 [OHCI])
Subsystem: ZOTAC International (MCO) Ltd. Device [19da:a191]
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap- 66MHz+ UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 32, Cache Line Size: 64 bytes
Interrupt: pin A routed to IRQ 18
Region 0: Memory at feb4c000 (32-bit, non-prefetchable) [size=4K]
Kernel driver in use: ohci_hcd
00:13.2 USB controller [0c03]: ATI Technologies Inc SB7x0/SB8x0/SB9x0 USB EHCI Controller [1002:4396] (prog-if 20 [EHCI])
Subsystem: ZOTAC International (MCO) Ltd. Device [19da:a191]
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV+ VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz+ UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 32, Cache Line Size: 64 bytes
Interrupt: pin B routed to IRQ 17
Region 0: Memory at feb4b000 (32-bit, non-prefetchable) [size=256]
Capabilities: <access denied>
Kernel driver in use: ehci_hcd
00:14.0 SMBus [0c05]: ATI Technologies Inc SBx00 SMBus Controller [1002:4385] (rev 42)
Subsystem: ZOTAC International (MCO) Ltd. Device [19da:a191]
Control: I/O+ Mem+ BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx+
Status: Cap- 66MHz+ UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Kernel driver in use: piix4_smbus
00:14.1 IDE interface [0101]: ATI Technologies Inc SB7x0/SB8x0/SB9x0 IDE Controller [1002:439c] (rev 40) (prog-if 8f [Master SecP SecO PriP PriO])
Subsystem: ZOTAC International (MCO) Ltd. Device [19da:a191]
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap- 66MHz+ UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 32
Interrupt: pin B routed to IRQ 17
Region 0: I/O ports at f140 [size=8]
Region 1: I/O ports at f130 [size=4]
Region 2: I/O ports at f120 [size=8]
Region 3: I/O ports at f110 [size=4]
Region 4: I/O ports at f100 [size=16]
Kernel driver in use: pata_atiixp
00:14.2 Audio device [0403]: ATI Technologies Inc SBx00 Azalia (Intel HDA) [1002:4383] (rev 40)
Subsystem: ZOTAC International (MCO) Ltd. Device [19da:a191]
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=slow >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 32, Cache Line Size: 64 bytes
Interrupt: pin A routed to IRQ 16
Region 0: Memory at feb40000 (64-bit, non-prefetchable) [size=16K]
Capabilities: <access denied>
Kernel driver in use: snd_hda_intel
00:14.3 ISA bridge [0601]: ATI Technologies Inc SB7x0/SB8x0/SB9x0 LPC host controller [1002:439d] (rev 40)
Subsystem: ZOTAC International (MCO) Ltd. Device [19da:a191]
Control: I/O+ Mem+ BusMaster+ SpecCycle+ MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap- 66MHz+ UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0
00:14.4 PCI bridge [0604]: ATI Technologies Inc SBx00 PCI to PCI Bridge [1002:4384] (rev 40) (prog-if 01 [Subtractive decode])
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop+ ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap- 66MHz+ UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 64
Bus: primary=00, secondary=02, subordinate=02, sec-latency=64
Secondary status: 66MHz- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort+ <SERR- <PERR-
BridgeCtl: Parity- SERR- NoISA- VGA- MAbort- >Reset- FastB2B-
PriDiscTmr- SecDiscTmr- DiscTmrStat- DiscTmrSERREn-
00:14.5 USB controller [0c03]: ATI Technologies Inc SB7x0/SB8x0/SB9x0 USB OHCI2 Controller [1002:4399] (prog-if 10 [OHCI])
Subsystem: ZOTAC International (MCO) Ltd. Device [19da:a191]
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap- 66MHz+ UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 32, Cache Line Size: 64 bytes
Interrupt: pin C routed to IRQ 18
Region 0: Memory at feb4a000 (32-bit, non-prefetchable) [size=4K]
Kernel driver in use: ohci_hcd
00:15.0 PCI bridge [0604]: ATI Technologies Inc SB700/SB800/SB900 PCI to PCI bridge (PCIE port 0) [1002:43a0] (prog-if 00 [Normal decode])
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0, Cache Line Size: 64 bytes
Bus: primary=00, secondary=03, subordinate=05, sec-latency=0
I/O behind bridge: 0000e000-0000efff
Memory behind bridge: fe000000-fe9fffff
Prefetchable memory behind bridge: 00000000c0000000-00000000cfffffff
Secondary status: 66MHz- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- <SERR- <PERR-
BridgeCtl: Parity- SERR- NoISA- VGA- MAbort- >Reset- FastB2B-
PriDiscTmr- SecDiscTmr- DiscTmrStat- DiscTmrSERREn-
Capabilities: <access denied>
Kernel driver in use: pcieport
00:15.3 PCI bridge [0604]: ATI Technologies Inc SB900 PCI to PCI bridge (PCIE port 3) [1002:43a3] (prog-if 00 [Normal decode])
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0, Cache Line Size: 64 bytes
Bus: primary=00, secondary=06, subordinate=06, sec-latency=0
I/O behind bridge: 0000d000-0000dfff
Prefetchable memory behind bridge: 00000000d0000000-00000000d00fffff
Secondary status: 66MHz- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- <SERR- <PERR-
BridgeCtl: Parity- SERR- NoISA- VGA- MAbort- >Reset- FastB2B-
PriDiscTmr- SecDiscTmr- DiscTmrStat- DiscTmrSERREn-
Capabilities: <access denied>
Kernel driver in use: pcieport
00:16.0 USB controller [0c03]: ATI Technologies Inc SB7x0/SB8x0/SB9x0 USB OHCI0 Controller [1002:4397] (prog-if 10 [OHCI])
Subsystem: ZOTAC International (MCO) Ltd. Device [19da:a191]
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap- 66MHz+ UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 32, Cache Line Size: 64 bytes
Interrupt: pin A routed to IRQ 18
Region 0: Memory at feb49000 (32-bit, non-prefetchable) [size=4K]
Kernel driver in use: ohci_hcd
00:16.2 USB controller [0c03]: ATI Technologies Inc SB7x0/SB8x0/SB9x0 USB EHCI Controller [1002:4396] (prog-if 20 [EHCI])
Subsystem: ZOTAC International (MCO) Ltd. Device [19da:a191]
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV+ VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz+ UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 32, Cache Line Size: 64 bytes
Interrupt: pin B routed to IRQ 17
Region 0: Memory at feb48000 (32-bit, non-prefetchable) [size=256]
Capabilities: <access denied>
Kernel driver in use: ehci_hcd
00:18.0 Host bridge [0600]: Advanced Micro Devices [AMD] Family 12h/14h Processor Function 0 [1022:1700] (rev 43)
Control: I/O- Mem- BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
00:18.1 Host bridge [0600]: Advanced Micro Devices [AMD] Family 12h/14h Processor Function 1 [1022:1701]
Control: I/O- Mem- BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap- 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
00:18.2 Host bridge [0600]: Advanced Micro Devices [AMD] Family 12h/14h Processor Function 2 [1022:1702]
Control: I/O- Mem- BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap- 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
00:18.3 Host bridge [0600]: Advanced Micro Devices [AMD] Family 12h/14h Processor Function 3 [1022:1703]
Control: I/O- Mem- BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Capabilities: <access denied>
Kernel driver in use: k10temp
00:18.4 Host bridge [0600]: Advanced Micro Devices [AMD] Family 12h/14h Processor Function 4 [1022:1704]
Control: I/O- Mem- BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap- 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
00:18.5 Host bridge [0600]: Advanced Micro Devices [AMD] Family 12h/14h Processor Function 6 [1022:1718]
Control: I/O- Mem- BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap- 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
00:18.6 Host bridge [0600]: Advanced Micro Devices [AMD] Family 12h/14h Processor Function 5 [1022:1716]
Control: I/O- Mem- BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap- 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
00:18.7 Host bridge [0600]: Advanced Micro Devices [AMD] Family 12h/14h Processor Function 7 [1022:1719]
Control: I/O- Mem- BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap- 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
01:00.0 USB controller [0c03]: NEC Corporation uPD720200 USB 3.0 Host Controller [1033:0194] (rev 03) (prog-if 30 [XHCI])
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx+
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0, Cache Line Size: 64 bytes
Interrupt: pin A routed to IRQ 16
Region 0: Memory at fea00000 (64-bit, non-prefetchable) [size=8K]
Capabilities: <access denied>
Kernel driver in use: xhci_hcd
03:00.0 Network controller [0280]: Atheros Communications Inc. AR9285 Wireless Network Adapter (PCI-Express) [168c:002b] (rev 01)
Subsystem: AzureWave AW-NB037H 802.11bgn Wireless Half-size Mini PCIe Card [AR9002WB-1NGCD] [1a3b:2c37]
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0, Cache Line Size: 64 bytes
Interrupt: pin A routed to IRQ 16
Region 0: Memory at fe000000 (64-bit, non-prefetchable) [size=64K]
Capabilities: <access denied>
Kernel driver in use: ath9k
06:00.0 Ethernet controller [0200]: Realtek Semiconductor Co., Ltd. RTL8111/8168B PCI Express Gigabit Ethernet controller [10ec:8168] (rev 06)
Subsystem: ZOTAC International (MCO) Ltd. Device [19da:a176]
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx+
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0, Cache Line Size: 64 bytes
Interrupt: pin A routed to IRQ 40
Region 0: I/O ports at d000 [size=256]
Region 2: Memory at d0004000 (64-bit, prefetchable) [size=4K]
Region 4: Memory at d0000000 (64-bit, prefetchable) [size=16K]
Capabilities: <access denied>
Kernel driver in use: r8169
** USB devices:
Bus 001 Device 001: ID 1d6b:0002 Linux Foundation 2.0 root hub
Bus 002 Device 001: ID 1d6b:0002 Linux Foundation 2.0 root hub
Bus 003 Device 001: ID 1d6b:0002 Linux Foundation 2.0 root hub
Bus 005 Device 001: ID 1d6b:0002 Linux Foundation 2.0 root hub
Bus 006 Device 001: ID 1d6b:0003 Linux Foundation 3.0 root hub
Bus 004 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub
Bus 007 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub
Bus 008 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub
Bus 009 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub
Bus 004 Device 002: ID 05ac:1003 Apple, Inc. Hub in Pro Keyboard [Mitsumi, A1048]
Bus 007 Device 002: ID 0cf3:3000 Atheros Communications, Inc. AR3011 Bluetooth (no firmware)
Bus 004 Device 003: ID 15d9:0a4c Trust International B.V. USB+PS/2 Optical Mouse
Bus 004 Device 004: ID 05ac:020b Apple, Inc. Pro Keyboard [Mitsumi, A1048/US layout]
-- System Information:
Debian Release: wheezy/sid
APT prefers testing
APT policy: (500, 'testing'), (500, 'stable')
Architecture: amd64 (x86_64)
Kernel: Linux 3.1.0-1-amd64 (SMP w/2 CPU cores)
Locale: LANG=en_AU.UTF-8, LC_CTYPE=en_AU.UTF-8 (charmap=UTF-8) (ignored: LC_ALL set to en_AU.UTF-8)
Shell: /bin/sh linked to /bin/dash
Versions of packages linux-image-3.1.0-1-amd64 depends on:
ii debconf [debconf-2.0] 1.5.41
ii initramfs-tools [linux-initramfs-tool] 0.99
ii linux-base 3.4
ii module-init-tools 3.16-1
Versions of packages linux-image-3.1.0-1-amd64 recommends:
ii firmware-linux-free 3
Versions of packages linux-image-3.1.0-1-amd64 suggests:
pn grub-pc 1.99-14
pn linux-doc-3.1 <none>
Versions of packages linux-image-3.1.0-1-amd64 is related to:
pn firmware-bnx2 <none>
pn firmware-bnx2x <none>
pn firmware-ipw2x00 <none>
pn firmware-ivtv <none>
pn firmware-iwlwifi <none>
pn firmware-linux <none>
pn firmware-linux-nonfree <none>
pn firmware-qlogic <none>
pn firmware-ralink <none>
pn xen-hypervisor <none>
-- debconf information:
* linux-image-3.1.0-1-amd64/postinst/missing-firmware-3.1.0-1-amd64:
linux-image-3.1.0-1-amd64/postinst/ignoring-ramdisk:
linux-image-3.1.0-1-amd64/postinst/depmod-error-initrd-3.1.0-1-amd64: false
linux-image-3.1.0-1-amd64/prerm/removing-running-kernel-3.1.0-1-amd64: true
--
\ “I went to a fancy French restaurant called ‘Déjà Vu’. The head |
`\ waiter said, ‘Don't I know you?’” —Steven Wright |
_o__) |
Ben Finney <ben@benfinney.id.au>Attachment:
signature.asc
Description: Digital signature