Bug#649735: kernel oops on removing an USB floppy drive
Package: linux-2.6
Version: 3.1.1-1
Severity: normal
I guess this is #593304.
it does not happen on attaching the drive for the first time.
-- Package-specific info:
** Version:
Linux version 3.1.0-1-amd64 (Debian 3.1.1-1) (ben@decadent.org.uk) (gcc version 4.6.2 (Debian 4.6.2-4) ) #1 SMP Mon Nov 14 08:02:25 UTC 2011
** Command line:
BOOT_IMAGE=/boot/vmlinuz-3.1.0-1-amd64 root=UUID=3b8f6a64-5899-462a-aec0-6ddefd878ecf ro fbcon=rotate:3 quiet
** Tainted: DO (4224)
* Kernel has oopsed before.
* Out-of-tree module has been loaded.
** Kernel log:
[ 129.460574] scsi: killing requests for dead queue
[ 129.460619] scsi: killing requests for dead queue
[ 129.460663] scsi: killing requests for dead queue
[ 129.461114] sd 12:0:0:0: Attached scsi generic sg8 type 0
[ 129.844288] sd 12:0:0:0: [sdh] Attached SCSI removable disk
[ 133.684280] sd 12:0:0:0: [sdh] READ CAPACITY failed
[ 133.684283] sd 12:0:0:0: [sdh] Result: hostbyte=DID_OK driverbyte=DRIVER_SENSE
[ 133.684287] sd 12:0:0:0: [sdh] Sense Key : Medium Error [current]
[ 133.684291] sd 12:0:0:0: [sdh] Add. Sense: Medium format corrupted
[ 133.812299] sd 12:0:0:0: [sdh] Write Protect is on
[ 133.812302] sd 12:0:0:0: [sdh] Mode Sense: 00 46 94 80
[ 133.940284] sd 12:0:0:0: [sdh] No Caching mode page present
[ 133.940288] sd 12:0:0:0: [sdh] Assuming drive cache: write through
[ 134.580301] sd 12:0:0:0: [sdh] READ CAPACITY failed
[ 134.580304] sd 12:0:0:0: [sdh] Result: hostbyte=DID_OK driverbyte=DRIVER_SENSE
[ 134.580308] sd 12:0:0:0: [sdh] Sense Key : Medium Error [current]
[ 134.580312] sd 12:0:0:0: [sdh] Add. Sense: Medium format corrupted
[ 134.836287] sd 12:0:0:0: [sdh] No Caching mode page present
[ 134.836291] sd 12:0:0:0: [sdh] Assuming drive cache: write through
[ 163.636285] sd 12:0:0:0: [sdh] READ CAPACITY failed
[ 163.636288] sd 12:0:0:0: [sdh] Result: hostbyte=DID_OK driverbyte=DRIVER_SENSE
[ 163.636292] sd 12:0:0:0: [sdh] Sense Key : Medium Error [current]
[ 163.636296] sd 12:0:0:0: [sdh] Add. Sense: Medium format corrupted
[ 163.892285] sd 12:0:0:0: [sdh] No Caching mode page present
[ 163.892289] sd 12:0:0:0: [sdh] Assuming drive cache: write through
[ 164.404284] sd 12:0:0:0: [sdh] READ CAPACITY failed
[ 164.404287] sd 12:0:0:0: [sdh] Result: hostbyte=DID_OK driverbyte=DRIVER_SENSE
[ 164.404290] sd 12:0:0:0: [sdh] Sense Key : Medium Error [current]
[ 164.404294] sd 12:0:0:0: [sdh] Add. Sense: Medium format corrupted
[ 164.660285] sd 12:0:0:0: [sdh] No Caching mode page present
[ 164.660288] sd 12:0:0:0: [sdh] Assuming drive cache: write through
[ 169.060046] usb 8-2: USB disconnect, device number 3
[ 169.060453] scsi: killing requests for dead queue
[ 169.060613] BUG: unable to handle kernel NULL pointer dereference at 0000000000000008
[ 169.060683] IP: [<ffffffffa0117792>] sd_revalidate_disk+0x33/0x1603 [sd_mod]
[ 169.060745] PGD 121d9a067 PUD 116e45067 PMD 0
[ 169.060783] Oops: 0000 [#1] SMP
[ 169.060811] CPU 2
[ 169.060825] Modules linked in: uinput binfmt_misc pci_stub vboxpci(O) vboxnetadp(O) vboxnetflt(O) vboxdrv(O) bridge stp xt_tcpudp xt_conntrack xt_state xt_dscp xt_DSCP xt_CLASSIFY ipt_LOG ipt_REJECT xt_owner nf_conntrack_tftp nf_nat_ftp nf_conntrack_ftp nf_nat_sip nf_conntrack_sip nf_nat_h323 nf_conntrack_h323 nf_nat_pptp nf_conntrack_pptp nf_conntrack_proto_gre nf_nat_proto_gre nf_nat_irc nf_conntrack_irc iptable_filter iptable_nat ipt_MASQUERADE nf_nat xt_multiport xt_iprange nf_conntrack_ipv4 nf_conntrack nf_defrag_ipv4 ip_tables x_tables tun fuse kvm_intel kvm snd_pcm_oss snd_mixer_oss coretemp loop snd_hda_codec_hdmi snd_hda_codec_analog joydev dell_wmi sparse_keymap snd_hda_intel snd_hda_codec evdev snd_hwdep snd_pcm snd_seq snd_timer snd_seq_device dcdbas tpm_tis tpm snd tpm_bios pcspkr i2c_i801 psmouse serio_raw soundcore snd_page_alloc parport_pc parport wmi processor button thermal_sys ext3 jbd mbcache sg sr_mod cdrom usbhid hid sd_mod crc_t10dif radeon ttm ahci
usb_storage uas uhci_hcd libahci drm_kms_helper drm sata_sil24 i2c_algo_bit i2c_core ata_generic power_supply ehci_hcd e1000e libata usbcore scsi_mod [last unloaded: scsi_wait_scan]
[ 169.061725]
[ 169.061738] Pid: 3892, comm: hald-addon-stor Tainted: G O 3.1.0-1-amd64 #1 Dell Inc. OptiPlex 960 /0Y958C
[ 169.061827] RIP: 0010:[<ffffffffa0117792>] [<ffffffffa0117792>] sd_revalidate_disk+0x33/0x1603 [sd_mod]
[ 169.061902] RSP: 0018:ffff8801205ffaf8 EFLAGS: 00010246
[ 169.061941] RAX: 0000000000000000 RBX: ffff88012354e1c0 RCX: 0000000000000001
[ 169.061992] RDX: 0000000000000001 RSI: ffff880121e17b80 RDI: ffff880116d04800
[ 169.062042] RBP: 0000000000000000 R08: 00000008ffffffff R09: ffff880123376250
[ 169.062093] R10: ffff880123376250 R11: ffff880123376250 R12: ffff880116d04800
[ 169.062143] R13: 0000000000000000 R14: ffff88012354e1d8 R15: ffff88012354e1c0
[ 169.062195] FS: 00007fa60b5ac700(0000) GS:ffff880127c80000(0000) knlGS:0000000000000000
[ 169.062252] CS: 0010 DS: 0000 ES: 0000 CR0: 0000000080050033
[ 169.062293] CR2: 0000000000000008 CR3: 000000011a254000 CR4: 00000000000406e0
[ 169.062344] DR0: 0000000000000000 DR1: 0000000000000000 DR2: 0000000000000000
[ 169.062394] DR3: 0000000000000000 DR6: 00000000ffff0ff0 DR7: 0000000000000400
[ 169.062445] Process hald-addon-stor (pid: 3892, threadinfo ffff8801205fe000, task ffff8801162c0970)
[ 169.062508] Stack:
[ 169.062523] ffff88012324b800 ffffffff81106ae1 ffffffff8119b410 ffff880116d04848
[ 169.062581] 0000000000000000 ffff880116d04800 000000000000001d ffff88012354e1d8
[ 169.062640] ffff88012354e1c0 ffff880116d04800 ffff88012354e1c0 ffff88012354e1c0
[ 169.062698] Call Trace:
[ 169.062721] [<ffffffff81106ae1>] ? iget5_locked+0x5c/0x127
[ 169.062764] [<ffffffff8119b410>] ? add_uevent_var+0xdc/0xdc
[ 169.062807] [<ffffffff81141189>] ? rescan_partitions+0xac/0x41b
[ 169.062852] [<ffffffff8111ad4e>] ? __blkdev_get+0x1a6/0x37e
[ 169.062895] [<ffffffff8111b1cd>] ? blkdev_get+0x2a7/0x2a7
[ 169.062936] [<ffffffff8111b0ed>] ? blkdev_get+0x1c7/0x2a7
[ 169.062976] [<ffffffff8111b1cd>] ? blkdev_get+0x2a7/0x2a7
[ 169.063017] [<ffffffff810f2506>] ? __dentry_open+0x17f/0x296
[ 169.063060] [<ffffffff810fb7fc>] ? dget+0x12/0x1e
[ 169.063096] [<ffffffff810fe9bb>] ? do_last+0x47c/0x591
[ 169.063135] [<ffffffff810fee28>] ? path_openat+0xce/0x31c
[ 169.063178] [<ffffffff810ff138>] ? do_filp_open+0x2a/0x6e
[ 169.063220] [<ffffffff8132c02f>] ? _cond_resched+0x7/0x1c
[ 169.063260] [<ffffffff811a2ad9>] ? __strncpy_from_user+0x18/0x48
[ 169.063305] [<ffffffff81107d07>] ? alloc_fd+0x64/0x109
[ 169.063344] [<ffffffff810f33c7>] ? do_sys_open+0x5e/0xe5
[ 169.063385] [<ffffffff813322d2>] ? system_call_fastpath+0x16/0x1b
[ 169.063428] Code: 55 53 48 81 ec 88 00 00 00 48 8b af 28 03 00 00 65 48 8b 04 25 28 00 00 00 48 89 44 24 78 31 c0 8b 05 23 bb f0 ff 48 89 7c 24 48 <4c> 8b 7d 08 c1 e8 15 83 e0 07 83 f8 03 76 43 48 8b 8d 78 02 00
[ 169.063655] RIP [<ffffffffa0117792>] sd_revalidate_disk+0x33/0x1603 [sd_mod]
[ 169.063711] RSP <ffff8801205ffaf8>
[ 169.063736] CR2: 0000000000000008
[ 169.109458] ---[ end trace 370c8b39cbcbe354 ]---
[ 177.904022] usb 8-2: new full speed USB device number 4 using uhci_hcd
[ 178.230037] usb 8-2: New USB device found, idVendor=0644, idProduct=0000
[ 178.230041] usb 8-2: New USB device strings: Mfr=1, Product=2, SerialNumber=0
[ 178.230044] usb 8-2: Product: TEAC FD-05PUB
[ 178.230046] usb 8-2: Manufacturer: TEAC
[ 178.234172] scsi13 : usb-storage 8-2:1.0
[ 179.301065] scsi 13:0:0:0: Direct-Access TEAC FD-05PUB 1026 PQ: 0 ANSI: 0 CCS
[ 179.301115] scsi: killing requests for dead queue
[ 179.301168] scsi: killing requests for dead queue
[ 179.301215] scsi: killing requests for dead queue
[ 179.301259] scsi: killing requests for dead queue
[ 179.301306] scsi: killing requests for dead queue
[ 179.301351] scsi: killing requests for dead queue
[ 179.301395] scsi: killing requests for dead queue
[ 179.301441] scsi: killing requests for dead queue
[ 179.301894] sd 13:0:0:0: Attached scsi generic sg8 type 0
[ 179.685054] sd 13:0:0:0: [sdh] Attached SCSI removable disk
[ 186.400043] usb 8-2: USB disconnect, device number 4
[ 186.400466] scsi: killing requests for dead queue
** Model information
sys_vendor: Dell Inc.
product_name: OptiPlex 960
product_version:
chassis_vendor: Dell Inc.
chassis_version:
bios_vendor: Dell Inc.
bios_version: A01
board_vendor: Dell Inc.
board_name: 0Y958C
board_version: A00
** PCI devices:
00:00.0 Host bridge [0600]: Intel Corporation 4 Series Chipset DRAM Controller [8086:2e10] (rev 03)
Subsystem: Dell Device [1028:0276]
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR+ FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort+ >SERR- <PERR- INTx-
Latency: 0
Capabilities: <access denied>
00:01.0 PCI bridge [0604]: Intel Corporation 4 Series Chipset PCI Express Root Port [8086:2e11] (rev 03) (prog-if 00 [Normal decode])
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR+ FastB2B- DisINTx+
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0, Cache Line Size: 64 bytes
Bus: primary=00, secondary=01, subordinate=01, sec-latency=0
I/O behind bridge: 0000d000-0000dfff
Memory behind bridge: fe900000-feafffff
Prefetchable memory behind bridge: 00000000d0000000-00000000dfffffff
Secondary status: 66MHz- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- <SERR- <PERR-
BridgeCtl: Parity- SERR+ NoISA- VGA+ MAbort- >Reset- FastB2B-
PriDiscTmr- SecDiscTmr- DiscTmrStat- DiscTmrSERREn-
Capabilities: <access denied>
Kernel driver in use: pcieport
00:03.0 Communication controller [0780]: Intel Corporation 4 Series Chipset HECI Controller [8086:2e14] (rev 03)
Subsystem: Dell Device [1028:0276]
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0
Interrupt: pin A routed to IRQ 11
Region 0: Memory at f0000800 (64-bit, non-prefetchable) [size=16]
Capabilities: <access denied>
00:03.2 IDE interface [0101]: Intel Corporation 4 Series Chipset PT IDER Controller [8086:2e16] (rev 03) (prog-if 85 [Master SecO PriO])
Subsystem: Dell Device [1028:0276]
Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz+ UDF- FastB2B+ ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0
Interrupt: pin C routed to IRQ 18
Region 0: I/O ports at fe80 [size=8]
Region 1: I/O ports at fe90 [size=4]
Region 2: I/O ports at fea0 [size=8]
Region 3: I/O ports at feb0 [size=4]
Region 4: I/O ports at fef0 [size=16]
Capabilities: <access denied>
Kernel driver in use: ata_generic
00:03.3 Serial controller [0700]: Intel Corporation 4 Series Chipset Serial KT Controller [8086:2e17] (rev 03) (prog-if 02 [16550])
Subsystem: Dell Device [1028:0276]
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz+ UDF- FastB2B+ ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0
Interrupt: pin B routed to IRQ 17
Region 0: I/O ports at ec98 [size=8]
Region 1: Memory at febd8000 (32-bit, non-prefetchable) [size=4K]
Capabilities: <access denied>
Kernel driver in use: serial
00:19.0 Ethernet controller [0200]: Intel Corporation 82567LM-3 Gigabit Network Connection [8086:10de] (rev 02)
Subsystem: Dell Device [1028:0276]
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR+ FastB2B- DisINTx+
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0
Interrupt: pin A routed to IRQ 48
Region 0: Memory at febe0000 (32-bit, non-prefetchable) [size=128K]
Region 1: Memory at febd9000 (32-bit, non-prefetchable) [size=4K]
Region 2: I/O ports at ecc0 [size=32]
Capabilities: <access denied>
Kernel driver in use: e1000e
00:1a.0 USB Controller [0c03]: Intel Corporation 82801JD/DO (ICH10 Family) USB UHCI Controller #4 [8086:3a67] (rev 02) (prog-if 00 [UHCI])
Subsystem: Dell Device [1028:0276]
Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0
Interrupt: pin A routed to IRQ 16
Region 4: I/O ports at ff20 [size=32]
Capabilities: <access denied>
Kernel driver in use: uhci_hcd
00:1a.1 USB Controller [0c03]: Intel Corporation 82801JD/DO (ICH10 Family) USB UHCI Controller #5 [8086:3a68] (rev 02) (prog-if 00 [UHCI])
Subsystem: Dell Device [1028:0276]
Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0
Interrupt: pin B routed to IRQ 17
Region 4: I/O ports at ff00 [size=32]
Capabilities: <access denied>
Kernel driver in use: uhci_hcd
00:1a.2 USB Controller [0c03]: Intel Corporation 82801JD/DO (ICH10 Family) USB UHCI Controller #6 [8086:3a69] (rev 02) (prog-if 00 [UHCI])
Subsystem: Dell Device [1028:0276]
Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0
Interrupt: pin C routed to IRQ 22
Region 4: I/O ports at fc00 [size=32]
Capabilities: <access denied>
Kernel driver in use: uhci_hcd
00:1a.7 USB Controller [0c03]: Intel Corporation 82801JD/DO (ICH10 Family) USB2 EHCI Controller #2 [8086:3a6c] (rev 02) (prog-if 20 [EHCI])
Subsystem: Dell Device [1028:0276]
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR+ FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0
Interrupt: pin C routed to IRQ 22
Region 0: Memory at febda000 (32-bit, non-prefetchable) [size=1K]
Capabilities: <access denied>
Kernel driver in use: ehci_hcd
00:1b.0 Audio device [0403]: Intel Corporation 82801JD/DO (ICH10 Family) HD Audio Controller [8086:3a6e] (rev 02)
Subsystem: Dell Device [1028:0276]
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR+ FastB2B- DisINTx+
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0, Cache Line Size: 64 bytes
Interrupt: pin A routed to IRQ 51
Region 0: Memory at febdc000 (64-bit, non-prefetchable) [size=16K]
Capabilities: <access denied>
Kernel driver in use: snd_hda_intel
00:1c.0 PCI bridge [0604]: Intel Corporation 82801JD/DO (ICH10 Family) PCI Express Port 1 [8086:3a70] (rev 02) (prog-if 00 [Normal decode])
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR+ FastB2B- DisINTx+
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0, Cache Line Size: 64 bytes
Bus: primary=00, secondary=02, subordinate=02, sec-latency=0
I/O behind bridge: 00001000-00001fff
Memory behind bridge: fe800000-fe8fffff
Prefetchable memory behind bridge: 00000000f0300000-00000000f04fffff
Secondary status: 66MHz- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- <SERR- <PERR-
BridgeCtl: Parity- SERR+ NoISA- VGA- MAbort- >Reset- FastB2B-
PriDiscTmr- SecDiscTmr- DiscTmrStat- DiscTmrSERREn-
Capabilities: <access denied>
Kernel driver in use: pcieport
00:1c.1 PCI bridge [0604]: Intel Corporation 82801JD/DO (ICH10 Family) PCI Express Port 2 [8086:3a72] (rev 02) (prog-if 00 [Normal decode])
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR+ FastB2B- DisINTx+
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0, Cache Line Size: 64 bytes
Bus: primary=00, secondary=03, subordinate=03, sec-latency=0
I/O behind bridge: 0000c000-0000cfff
Memory behind bridge: fe700000-fe7fffff
Prefetchable memory behind bridge: 00000000f0100000-00000000f02fffff
Secondary status: 66MHz- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- <SERR- <PERR-
BridgeCtl: Parity- SERR+ NoISA- VGA- MAbort- >Reset- FastB2B-
PriDiscTmr- SecDiscTmr- DiscTmrStat- DiscTmrSERREn-
Capabilities: <access denied>
Kernel driver in use: pcieport
00:1d.0 USB Controller [0c03]: Intel Corporation 82801JD/DO (ICH10 Family) USB UHCI Controller #1 [8086:3a64] (rev 02) (prog-if 00 [UHCI])
Subsystem: Dell Device [1028:0276]
Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0
Interrupt: pin A routed to IRQ 23
Region 4: I/O ports at ff80 [size=32]
Capabilities: <access denied>
Kernel driver in use: uhci_hcd
00:1d.1 USB Controller [0c03]: Intel Corporation 82801JD/DO (ICH10 Family) USB UHCI Controller #2 [8086:3a65] (rev 02) (prog-if 00 [UHCI])
Subsystem: Dell Device [1028:0276]
Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0
Interrupt: pin B routed to IRQ 17
Region 4: I/O ports at ff60 [size=32]
Capabilities: <access denied>
Kernel driver in use: uhci_hcd
00:1d.2 USB Controller [0c03]: Intel Corporation 82801JD/DO (ICH10 Family) USB UHCI Controller #3 [8086:3a66] (rev 02) (prog-if 00 [UHCI])
Subsystem: Dell Device [1028:0276]
Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0
Interrupt: pin C routed to IRQ 18
Region 4: I/O ports at ff40 [size=32]
Capabilities: <access denied>
Kernel driver in use: uhci_hcd
00:1d.7 USB Controller [0c03]: Intel Corporation 82801JD/DO (ICH10 Family) USB2 EHCI Controller #1 [8086:3a6a] (rev 02) (prog-if 20 [EHCI])
Subsystem: Dell Device [1028:0276]
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR+ FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0
Interrupt: pin A routed to IRQ 23
Region 0: Memory at ff980000 (32-bit, non-prefetchable) [size=1K]
Capabilities: <access denied>
Kernel driver in use: ehci_hcd
00:1e.0 PCI bridge [0604]: Intel Corporation 82801 PCI Bridge [8086:244e] (rev a2) (prog-if 01 [Subtractive decode])
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR+ FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0
Bus: primary=00, secondary=04, subordinate=04, sec-latency=32
Secondary status: 66MHz- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort+ <SERR- <PERR-
BridgeCtl: Parity- SERR+ NoISA- VGA- MAbort- >Reset- FastB2B-
PriDiscTmr- SecDiscTmr- DiscTmrStat- DiscTmrSERREn-
Capabilities: <access denied>
00:1f.0 ISA bridge [0601]: Intel Corporation 82801JDO (ICH10DO) LPC Interface Controller [8086:3a14] (rev 02)
Subsystem: Dell Device [1028:0276]
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR+ FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0
Capabilities: <access denied>
00:1f.2 SATA controller [0106]: Intel Corporation 82801JD/DO (ICH10 Family) SATA AHCI Controller [8086:3a02] (rev 02) (prog-if 01 [AHCI 1.0])
Subsystem: Dell Device [1028:0276]
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx+
Status: Cap+ 66MHz+ UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0
Interrupt: pin C routed to IRQ 49
Region 0: I/O ports at fe00 [size=8]
Region 1: I/O ports at fe10 [size=4]
Region 2: I/O ports at fe20 [size=8]
Region 3: I/O ports at fe30 [size=4]
Region 4: I/O ports at fec0 [size=32]
Region 5: Memory at f0000000 (32-bit, non-prefetchable) [size=2K]
Capabilities: <access denied>
Kernel driver in use: ahci
00:1f.3 SMBus [0c05]: Intel Corporation 82801JD/DO (ICH10 Family) SMBus Controller [8086:3a60] (rev 02)
Subsystem: Dell Device [1028:0276]
Control: I/O+ Mem+ BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR+ FastB2B- DisINTx-
Status: Cap- 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Interrupt: pin C routed to IRQ 18
Region 0: Memory at febdb000 (64-bit, non-prefetchable) [size=256]
Region 4: I/O ports at ece0 [size=32]
Kernel driver in use: i801_smbus
01:00.0 VGA compatible controller [0300]: ATI Technologies Inc Redwood [Radeon HD 5670] [1002:68d8] (prog-if 00 [VGA controller])
Subsystem: PC Partner Limited Device [174b:e151]
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx+
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0, Cache Line Size: 64 bytes
Interrupt: pin A routed to IRQ 50
Region 0: Memory at d0000000 (64-bit, prefetchable) [size=256M]
Region 2: Memory at fe9e0000 (64-bit, non-prefetchable) [size=128K]
Region 4: I/O ports at dc00 [size=256]
Expansion ROM at fea00000 [disabled] [size=128K]
Capabilities: <access denied>
Kernel driver in use: radeon
01:00.1 Audio device [0403]: ATI Technologies Inc Redwood HDMI Audio [Radeon HD 5600 Series] [1002:aa60]
Subsystem: PC Partner Limited Device [174b:aa60]
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx+
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0, Cache Line Size: 64 bytes
Interrupt: pin B routed to IRQ 52
Region 0: Memory at fe9dc000 (64-bit, non-prefetchable) [size=16K]
Capabilities: <access denied>
Kernel driver in use: snd_hda_intel
03:00.0 Mass storage controller [0180]: Silicon Image, Inc. SiI 3531 [SATALink/SATARaid] Serial ATA Controller [1095:3531] (rev 01)
Subsystem: Silicon Image, Inc. SiI 3531 [SATALink/SATARaid] Serial ATA Controller [1095:3531]
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0, Cache Line Size: 64 bytes
Interrupt: pin A routed to IRQ 17
Region 0: Memory at fe7fd000 (64-bit, non-prefetchable) [size=128]
Region 2: Memory at fe7fe000 (64-bit, non-prefetchable) [size=8K]
Region 4: I/O ports at cc80 [size=128]
Capabilities: <access denied>
Kernel driver in use: sata_sil24
** USB devices:
Bus 008 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub
Bus 007 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub
Bus 006 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub
Bus 005 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub
Bus 004 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub
Bus 003 Device 004: ID 047d:2048 Kensington
Bus 003 Device 003: ID 04b3:301b IBM Corp. SK-8815 Keyboard
Bus 003 Device 002: ID 04b3:301a IBM Corp.
Bus 003 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub
Bus 002 Device 003: ID 152d:2336 JMicron Technology Corp. / JMicron USA Technology Corp. Hard Disk Drive
Bus 002 Device 002: ID 0644:0200 TEAC Corp. All-In-One Multi-Card Reader CA200/B/S
Bus 002 Device 001: ID 1d6b:0002 Linux Foundation 2.0 root hub
Bus 001 Device 003: ID 0409:0059 NEC Corp. HighSpeed Hub
Bus 001 Device 001: ID 1d6b:0002 Linux Foundation 2.0 root hub
-- System Information:
Debian Release: wheezy/sid
APT prefers stable
APT policy: (900, 'stable'), (500, 'testing'), (410, 'unstable'), (200, 'experimental'), (111, 'oldstable'), (107, 'natty-updates'), (107, 'natty')
Architecture: amd64 (x86_64)
Kernel: Linux 3.1.0-1-amd64 (SMP w/4 CPU cores)
Locale: LANG=en_US.UTF-8, LC_CTYPE=en_US.UTF-8 (charmap=UTF-8) (ignored: LC_ALL set to en_US.UTF-8)
Shell: /bin/sh linked to /bin/bash
Versions of packages linux-image-3.1.0-1-amd64 depends on:
ii debconf [debconf-2.0] 1.5.36.1 Debian configuration management sy
ii initramfs-tools [linux-initra 0.99+lm tools for generating an initramfs
ii linux-base 3.3 Linux image base package
ii module-init-tools 3.12-1 tools for managing Linux kernel mo
Versions of packages linux-image-3.1.0-1-amd64 recommends:
ii firmware-linux-free 3 Binary firmware for various driver
Versions of packages linux-image-3.1.0-1-amd64 suggests:
ii grub-pc 1.98+20100804-14+squeeze1 GRand Unified Bootloader, version
pn linux-doc-3.1 <none> (no description available)
Versions of packages linux-image-3.1.0-1-amd64 is related to:
pn firmware-bnx2 <none> (no description available)
pn firmware-bnx2x <none> (no description available)
pn firmware-ipw2x00 <none> (no description available)
pn firmware-ivtv <none> (no description available)
pn firmware-iwlwifi <none> (no description available)
pn firmware-linux <none> (no description available)
ii firmware-linux-nonfree 0.34 Binary firmware for various driver
pn firmware-qlogic <none> (no description available)
pn firmware-ralink <none> (no description available)
pn xen-hypervisor <none> (no description available)
-- debconf information excluded
Reply to: