Bug#644736: network-manager fails to reconnect to wifi
Package: linux-2.6
Version: 2.6.39-3~bpo60+1
Severity: normal
*** Please type your report below this line ***
if wifi signal is very bad:
1) network-manager disconnects from wifi after 5 minutes.
2) If I try to reconnect to wifi - it fails to connect.
3) If I reboot computer - it connects properly.
Please take a look at
https://bugs.launchpad.net/ubuntu/+source/linux/+bug/736171
Maybe it can help you to fix this bug.
-- Package-specific info:
** Version:
Linux version 2.6.39-bpo.2-amd64 (Debian 2.6.39-3~bpo60+1)
(norbert@tretkowski.de) (gcc version 4.4.5 (Debian 4.4.5-8) ) #1 SMP
Tue Jul 26 10:35:23 UTC 2011
** Command line:
BOOT_IMAGE=/boot/vmlinuz-2.6.39-bpo.2-amd64
root=UUID=ea13e98f-f082-4607-ac98-7f04b9b299a5 ro quiet
** Tainted: O (4096)
* Out-of-tree module has been loaded.
** Kernel log:
[ 1128.298318] ath: Could not stop RX, we could be confusing the DMA
engine when we start RX up
[ 1128.368712] ath: Failed to stop TX DMA!
[ 1128.382362] ath: DMA failed to stop in 10 ms AR_CR=0x00000024
AR_DIAG_SW=0x02000020 DMADBG_7=0x00006040
[ 1128.382367] ath: Could not stop RX, we could be confusing the DMA
engine when we start RX up
[ 1128.525797] ath: DMA failed to stop in 10 ms AR_CR=0x00000024
AR_DIAG_SW=0x02000020 DMADBG_7=0x00008040
[ 1128.525806] ath: Could not stop RX, we could be confusing the DMA
engine when we start RX up
[ 1128.669826] ath: DMA failed to stop in 10 ms AR_CR=0x00000024
AR_DIAG_SW=0x02000020 DMADBG_7=0x00008040
[ 1128.669835] ath: Could not stop RX, we could be confusing the DMA
engine when we start RX up
[ 1128.813829] ath: DMA failed to stop in 10 ms AR_CR=0x00000024
AR_DIAG_SW=0x02000020 DMADBG_7=0x00008040
[ 1128.813838] ath: Could not stop RX, we could be confusing the DMA
engine when we start RX up
[ 1128.834132] ath: DMA failed to stop in 10 ms AR_CR=0x00000024
AR_DIAG_SW=0x02000020 DMADBG_7=0x00008040
[ 1128.834138] ath: Could not stop RX, we could be confusing the DMA
engine when we start RX up
[ 1209.855043] ath: Failed to stop TX DMA!
[ 1209.863680] ath: Failed to stop TX DMA!
[ 1209.877322] ath: DMA failed to stop in 10 ms AR_CR=0x00000024
AR_DIAG_SW=0x02000020 DMADBG_7=0x00006040
[ 1209.877328] ath: Could not stop RX, we could be confusing the DMA
engine when we start RX up
[ 1209.897479] ath: DMA failed to stop in 10 ms AR_CR=0x00000024
AR_DIAG_SW=0x02000020 DMADBG_7=0x00008040
[ 1209.897484] ath: Could not stop RX, we could be confusing the DMA
engine when we start RX up
[ 1209.964755] ath: Failed to stop TX DMA!
[ 1209.978414] ath: DMA failed to stop in 10 ms AR_CR=0x00000024
AR_DIAG_SW=0x02000020 DMADBG_7=0x00008040
[ 1209.978420] ath: Could not stop RX, we could be confusing the DMA
engine when we start RX up
[ 1210.048716] ath: Failed to stop TX DMA!
[ 1210.062376] ath: DMA failed to stop in 10 ms AR_CR=0x00000024
AR_DIAG_SW=0x02000020 DMADBG_7=0x00008040
[ 1210.062382] ath: Could not stop RX, we could be confusing the DMA
engine when we start RX up
[ 1210.132747] ath: Failed to stop TX DMA!
[ 1210.146417] ath: DMA failed to stop in 10 ms AR_CR=0x00000024
AR_DIAG_SW=0x02000020 DMADBG_7=0x00008040
[ 1210.146423] ath: Could not stop RX, we could be confusing the DMA
engine when we start RX up
[ 1210.216737] ath: Failed to stop TX DMA!
[ 1210.230390] ath: DMA failed to stop in 10 ms AR_CR=0x00000024
AR_DIAG_SW=0x02000020 DMADBG_7=0x00008040
[ 1210.230395] ath: Could not stop RX, we could be confusing the DMA
engine when we start RX up
[ 1210.300721] ath: Failed to stop TX DMA!
[ 1210.314366] ath: DMA failed to stop in 10 ms AR_CR=0x00000024
AR_DIAG_SW=0x02000020 DMADBG_7=0x00008040
[ 1210.314371] ath: Could not stop RX, we could be confusing the DMA
engine when we start RX up
[ 1210.384723] ath: Failed to stop TX DMA!
[ 1210.398363] ath: DMA failed to stop in 10 ms AR_CR=0x00000024
AR_DIAG_SW=0x02000020 DMADBG_7=0x00008040
[ 1210.398369] ath: Could not stop RX, we could be confusing the DMA
engine when we start RX up
[ 1210.468740] ath: Failed to stop TX DMA!
[ 1210.482382] ath: DMA failed to stop in 10 ms AR_CR=0x00000024
AR_DIAG_SW=0x02000020 DMADBG_7=0x00008040
[ 1210.482388] ath: Could not stop RX, we could be confusing the DMA
engine when we start RX up
[ 1210.552738] ath: Failed to stop TX DMA!
[ 1210.566388] ath: DMA failed to stop in 10 ms AR_CR=0x00000024
AR_DIAG_SW=0x02000020 DMADBG_7=0x00008040
[ 1210.566394] ath: Could not stop RX, we could be confusing the DMA
engine when we start RX up
[ 1210.636713] ath: Failed to stop TX DMA!
[ 1210.650373] ath: DMA failed to stop in 10 ms AR_CR=0x00000024
AR_DIAG_SW=0x02000020 DMADBG_7=0x00008040
[ 1210.650378] ath: Could not stop RX, we could be confusing the DMA
engine when we start RX up
[ 1210.720700] ath: Failed to stop TX DMA!
[ 1210.734337] ath: DMA failed to stop in 10 ms AR_CR=0x00000024
AR_DIAG_SW=0x02000020 DMADBG_7=0x00006040
[ 1210.734343] ath: Could not stop RX, we could be confusing the DMA
engine when we start RX up
[ 1210.877987] ath: DMA failed to stop in 10 ms AR_CR=0x00000024
AR_DIAG_SW=0x02000020 DMADBG_7=0x00008040
[ 1210.877996] ath: Could not stop RX, we could be confusing the DMA
engine when we start RX up
[ 1211.021760] ath: DMA failed to stop in 10 ms AR_CR=0x00000024
AR_DIAG_SW=0x02000020 DMADBG_7=0x00008040
[ 1211.021769] ath: Could not stop RX, we could be confusing the DMA
engine when we start RX up
[ 1211.165797] ath: DMA failed to stop in 10 ms AR_CR=0x00000024
AR_DIAG_SW=0x02000020 DMADBG_7=0x00008040
[ 1211.165806] ath: Could not stop RX, we could be confusing the DMA
engine when we start RX up
[ 1211.185997] ath: DMA failed to stop in 10 ms AR_CR=0x00000024
AR_DIAG_SW=0x02000020 DMADBG_7=0x00008040
[ 1211.186003] ath: Could not stop RX, we could be confusing the DMA
engine when we start RX up
[ 1329.854889] ath: Failed to stop TX DMA!
[ 1329.863500] ath: Failed to stop TX DMA!
[ 1329.877138] ath: DMA failed to stop in 10 ms AR_CR=0x00000024
AR_DIAG_SW=0x02000020 DMADBG_7=0x00006040
[ 1329.877143] ath: Could not stop RX, we could be confusing the DMA
engine when we start RX up
[ 1329.897287] ath: DMA failed to stop in 10 ms AR_CR=0x00000024
AR_DIAG_SW=0x02000020 DMADBG_7=0x00008040
[ 1329.897292] ath: Could not stop RX, we could be confusing the DMA
engine when we start RX up
[ 1329.964799] ath: Failed to stop TX DMA!
[ 1329.978443] ath: DMA failed to stop in 10 ms AR_CR=0x00000024
AR_DIAG_SW=0x02000020 DMADBG_7=0x00008040
[ 1329.978449] ath: Could not stop RX, we could be confusing the DMA
engine when we start RX up
[ 1330.048713] ath: Failed to stop TX DMA!
[ 1330.062353] ath: DMA failed to stop in 10 ms AR_CR=0x00000024
AR_DIAG_SW=0x02000020 DMADBG_7=0x00008040
[ 1330.062358] ath: Could not stop RX, we could be confusing the DMA
engine when we start RX up
[ 1330.132704] ath: Failed to stop TX DMA!
[ 1330.146349] ath: DMA failed to stop in 10 ms AR_CR=0x00000024
AR_DIAG_SW=0x02000020 DMADBG_7=0x00008040
[ 1330.146354] ath: Could not stop RX, we could be confusing the DMA
engine when we start RX up
[ 1330.216712] ath: Failed to stop TX DMA!
[ 1330.230349] ath: DMA failed to stop in 10 ms AR_CR=0x00000024
AR_DIAG_SW=0x02000020 DMADBG_7=0x00008040
[ 1330.230354] ath: Could not stop RX, we could be confusing the DMA
engine when we start RX up
[ 1330.300712] ath: Failed to stop TX DMA!
[ 1330.314348] ath: DMA failed to stop in 10 ms AR_CR=0x00000024
AR_DIAG_SW=0x02000020 DMADBG_7=0x00008040
[ 1330.314354] ath: Could not stop RX, we could be confusing the DMA
engine when we start RX up
[ 1330.384712] ath: Failed to stop TX DMA!
[ 1330.398348] ath: DMA failed to stop in 10 ms AR_CR=0x00000024
AR_DIAG_SW=0x02000020 DMADBG_7=0x00008040
[ 1330.398354] ath: Could not stop RX, we could be confusing the DMA
engine when we start RX up
[ 1330.468739] ath: Failed to stop TX DMA!
[ 1330.482375] ath: DMA failed to stop in 10 ms AR_CR=0x00000024
AR_DIAG_SW=0x02000020 DMADBG_7=0x00008040
[ 1330.482381] ath: Could not stop RX, we could be confusing the DMA
engine when we start RX up
[ 1330.552712] ath: Failed to stop TX DMA!
[ 1330.566355] ath: DMA failed to stop in 10 ms AR_CR=0x00000024
AR_DIAG_SW=0x02000020 DMADBG_7=0x00008040
[ 1330.566360] ath: Could not stop RX, we could be confusing the DMA
engine when we start RX up
[ 1330.636710] ath: Failed to stop TX DMA!
[ 1330.650349] ath: DMA failed to stop in 10 ms AR_CR=0x00000024
AR_DIAG_SW=0x02000020 DMADBG_7=0x00008040
[ 1330.650354] ath: Could not stop RX, we could be confusing the DMA
engine when we start RX up
[ 1330.720774] ath: Failed to stop TX DMA!
[ 1330.734481] ath: DMA failed to stop in 10 ms AR_CR=0x00000024
AR_DIAG_SW=0x02000020 DMADBG_7=0x00006040
[ 1330.734487] ath: Could not stop RX, we could be confusing the DMA
engine when we start RX up
[ 1330.877961] ath: DMA failed to stop in 10 ms AR_CR=0x00000024
AR_DIAG_SW=0x02000020 DMADBG_7=0x00008040
[ 1330.877970] ath: Could not stop RX, we could be confusing the DMA
engine when we start RX up
[ 1331.021807] ath: DMA failed to stop in 10 ms AR_CR=0x00000024
AR_DIAG_SW=0x02000020 DMADBG_7=0x00008040
[ 1331.021816] ath: Could not stop RX, we could be confusing the DMA
engine when we start RX up
[ 1331.165893] ath: DMA failed to stop in 10 ms AR_CR=0x00000024
AR_DIAG_SW=0x02000020 DMADBG_7=0x00008040
[ 1331.165902] ath: Could not stop RX, we could be confusing the DMA
engine when we start RX up
[ 1331.186077] ath: DMA failed to stop in 10 ms AR_CR=0x00000024
AR_DIAG_SW=0x02000020 DMADBG_7=0x00008040
[ 1331.186082] ath: Could not stop RX, we could be confusing the DMA
engine when we start RX up
** Model information
sys_vendor: ASUSTeK Computer Inc.
product_name: K53BY
product_version: 1.0
chassis_vendor: ASUSTeK Computer Inc.
chassis_version: 1.0
bios_vendor: American Megatrends Inc.
bios_version: 209
board_vendor: ASUSTeK Computer Inc.
board_name: K53BY
board_version: 1.0
** Loaded modules:
Module Size Used by
mperf 12411 0
cpufreq_userspace 12576 0
cpufreq_powersave 12454 0
cpufreq_conservative 13147 0
cpufreq_stats 12762 0
parport_pc 22191 0
ppdev 12725 0
lp 17190 0
parport 31650 3 parport_pc,ppdev,lp
bridge 65614 0
stp 12392 1 bridge
bnep 17424 2
rfcomm 32744 0
bluetooth 107224 10 bnep,rfcomm
crc16 12343 1 bluetooth
vboxnetadp 13185 0
vboxnetflt 24179 0
vboxdrv 178736 2 vboxnetadp,vboxnetflt
binfmt_misc 12914 1
uinput 17392 1
fuse 61554 1
nfsd 258506 2
nfs 251154 0
lockd 70844 2 nfsd,nfs
fscache 36071 1 nfs
auth_rpcgss 36788 2 nfsd,nfs
nfs_acl 12511 2 nfsd,nfs
sunrpc 162130 6 nfsd,nfs,lockd,auth_rpcgss,nfs_acl
loop 22479 0
snd_hda_codec_realtek 283734 1
snd_hda_codec_hdmi 22174 1
snd_hda_intel 25946 1
uvcvideo 57386 0
snd_hda_codec 67865 3
snd_hda_codec_realtek,snd_hda_codec_hdmi,snd_hda_intel
videodev 66266 1 uvcvideo
media 18148 1 videodev
snd_hwdep 13148 1 snd_hda_codec
snd_pcm 67276 3 snd_hda_codec_hdmi,snd_hda_intel,snd_hda_codec
v4l2_compat_ioctl32 16575 1 videodev
snd_seq 44678 0
snd_timer 22658 2 snd_pcm,snd_seq
arc4 12458 2
ecb 12737 2
snd_seq_device 13155 1 snd_seq
ath9k 71748 0
mac80211 181270 1 ath9k
ath9k_common 12732 1 ath9k
ath9k_hw 277119 2 ath9k,ath9k_common
snd 52324 11
snd_hda_codec_realtek,snd_hda_codec_hdmi,snd_hda_intel,snd_hda_codec,snd_hwdep,snd_pcm,snd_seq,snd_timer,snd_seq_device
radeon 743013 3
ath 21306 2 ath9k,ath9k_hw
ttm 52224 1 radeon
drm_kms_helper 26950 1 radeon
cfg80211 126244 3 ath9k,mac80211,ath
drm 166500 5 radeon,ttm,drm_kms_helper
tpm_tis 13125 0
soundcore 13014 1 snd
asus_nb_wmi 12393 0
tpm 17756 1 tpm_tis
asus_wmi 18488 1 asus_nb_wmi
psmouse 55199 0
pcspkr 12579 0
sparse_keymap 12760 1 asus_wmi
snd_page_alloc 12969 2 snd_hda_intel,snd_pcm
i2c_piix4 12536 0
i2c_algo_bit 12834 1 radeon
rfkill 19014 5 bluetooth,cfg80211,asus_wmi
i2c_core 23766 6
videodev,radeon,drm_kms_helper,drm,i2c_piix4,i2c_algo_bit
tpm_bios 12903 1 tpm
ac 12624 0
battery 13109 0
pci_hotplug 30807 1 asus_wmi
serio_raw 12878 0
power_supply 13475 3 radeon,ac,battery
k10temp 12611 0
evdev 17475 20
processor 27431 2
wmi 13202 1 asus_wmi
video 17553 0
button 12895 0
ext3 112254 2
jbd 41698 1 ext3
mbcache 12930 1 ext3
usb_storage 43639 0
uas 13151 0
sg 25769 0
sr_mod 21824 0
sd_mod 35644 4
crc_t10dif 12348 1 sd_mod
cdrom 35134 1 sr_mod
ata_generic 12479 0
ohci_hcd 26362 0
ahci 25089 4
libahci 22616 1 ahci
pata_atiixp 12689 0
libata 151572 4 ata_generic,ahci,libahci,pata_atiixp
ehci_hcd 39487 0
thermal 17330 0
thermal_sys 17939 3 processor,video,thermal
scsi_mod 161557 6 usb_storage,uas,sg,sr_mod,sd_mod,libata
usbcore 127203 6 uvcvideo,usb_storage,uas,ohci_hcd,ehci_hcd
r8169 37356 0
mii 12675 1 r8169
** Network interface configuration:
# This file describes the network interfaces available on your system
# and how to activate them. For more information, see interfaces(5).
# The loopback network interface
auto lo
iface lo inet loopback
** Network status:
*** IP interfaces and addresses:
1: lo: <LOOPBACK,UP,LOWER_UP> mtu 16436 qdisc noqueue state UNKNOWN
link/loopback 00:00:00:00:00:00 brd 00:00:00:00:00:00
inet 127.0.0.1/8 scope host lo
inet6 ::1/128 scope host
valid_lft forever preferred_lft forever
2: eth0: <NO-CARRIER,BROADCAST,MULTICAST,UP> mtu 1500 qdisc pfifo_fast
state DOWN qlen 1000
link/ether f4:6d:04:a4:da:d8 brd ff:ff:ff:ff:ff:ff
3: wlan0: <NO-CARRIER,BROADCAST,MULTICAST,UP> mtu 1500 qdisc mq state
DOWN qlen 1000
link/ether e0:b9:a5:80:d8:cf brd ff:ff:ff:ff:ff:ff
inet6 fe80::e2b9:a5ff:fe80:d8cf/64 scope link
valid_lft forever preferred_lft forever
4: vboxnet0: <BROADCAST,MULTICAST> mtu 1500 qdisc noop state DOWN qlen 1000
link/ether 0a:00:27:00:00:00 brd ff:ff:ff:ff:ff:ff
5: pan0: <BROADCAST,MULTICAST> mtu 1500 qdisc noop state DOWN
link/ether ba:0a:1d:37:ca:cb brd ff:ff:ff:ff:ff:ff
*** Device statistics:
Inter-| Receive | Transmit
face |bytes packets errs drop fifo frame compressed
multicast|bytes packets errs drop fifo colls carrier compressed
lo: 3721 65 0 0 0 0 0 0
3721 65 0 0 0 0 0 0
eth0: 0 0 0 0 0 0 0 0
0 0 0 0 0 0 0 0
wlan0: 375295 1005 0 0 0 0 0 0
236598 1440 0 0 0 0 0 0
vboxnet0: 0 0 0 0 0 0 0 0
0 0 0 0 0 0 0 0
pan0: 0 0 0 0 0 0 0 0
0 0 0 0 0 0 0 0
*** Protocol statistics:
Ip:
1143 total packets received
8 with invalid addresses
0 forwarded
0 incoming packets discarded
1135 incoming packets delivered
1440 requests sent out
8 outgoing packets dropped
29 dropped because of missing route
Icmp:
20 ICMP messages received
0 input ICMP message failed.
ICMP input histogram:
destination unreachable: 20
80 ICMP messages sent
0 ICMP messages failed
ICMP output histogram:
destination unreachable: 80
IcmpMsg:
InType3: 20
OutType3: 80
Tcp:
99 active connections openings
0 passive connection openings
6 failed connection attempts
8 connection resets received
0 connections established
765 segments received
973 segments send out
61 segments retransmited
0 bad segments received.
13 resets sent
Udp:
345 packets received
82 packets to unknown port received.
0 packet receive errors
331 packets sent
UdpLite:
TcpExt:
41 TCP sockets finished time wait in fast timer
49 delayed acks sent
88 packet headers predicted
205 acknowledgments not containing data payload received
35 predicted acknowledgments
3 congestion windows recovered without slow start after partial ack
1 timeouts after SACK recovery
24 other TCP timeouts
1 connections reset due to unexpected data
8 connections reset due to early user close
1 connections aborted due to timeout
TCPSackShiftFallback: 1
IpExt:
InMcastPkts: 16
OutMcastPkts: 23
InBcastPkts: 80
OutBcastPkts: 78
InOctets: 378430
OutOctets: 182115
InMcastOctets: 4783
OutMcastOctets: 5063
InBcastOctets: 10766
OutBcastOctets: 10102
*** Device features:
eth0: 0x4180
lo: 0x201b7c65
pan0: 0xff78e5
vboxnet0: 0x4000
wlan0: 0x6000
** PCI devices:
00:00.0 Host bridge [0600]: Advanced Micro Devices [AMD] Device [1022:1510]
Subsystem: Advanced Micro Devices [AMD] Device [1022:1510]
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B- DisINTx-
Status: Cap- 66MHz+ UDF- FastB2B- ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 32
00:01.0 VGA compatible controller [0300]: ATI Technologies Inc Device
[1002:9802] (prog-if 00 [VGA controller])
Subsystem: ASUSTeK Computer Inc. Device [1043:101c]
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B- DisINTx+
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort-
<TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0, Cache Line Size: 64 bytes
Interrupt: pin A routed to IRQ 41
Region 0: Memory at b0000000 (32-bit, prefetchable) [size=256M]
Region 1: I/O ports at f000 [size=256]
Region 2: Memory at feb00000 (32-bit, non-prefetchable) [size=256K]
Expansion ROM at <unassigned> [disabled]
Capabilities: [50] Power Management version 3
Flags: PMEClk- DSI- D1+ D2+ AuxCurrent=0mA
PME(D0-,D1-,D2-,D3hot-,D3cold-)
Status: D0 NoSoftRst- PME-Enable- DSel=0 DScale=0 PME-
Capabilities: [58] Express (v2) Root Complex Integrated Endpoint, MSI 00
DevCap: MaxPayload 128 bytes, PhantFunc 0, Latency L0s
<4us, L1 unlimited
ExtTag+ RBE+ FLReset-
DevCtl: Report errors: Correctable- Non-Fatal- Fatal-
Unsupported-
RlxdOrd+ ExtTag- PhantFunc- AuxPwr- NoSnoop+
MaxPayload 128 bytes, MaxReadReq 128 bytes
DevSta: CorrErr- UncorrErr- FatalErr- UnsuppReq-
AuxPwr- TransPend-
LnkCap: Port #0, Speed unknown, Width x0, ASPM unknown,
Latency L0
<64ns, L1 <1us
ClockPM- Surprise- LLActRep- BwNot-
LnkCtl: ASPM Disabled; Disabled- Retrain- CommClk-
ExtSynch- ClockPM- AutWidDis- BWInt- AutBWInt-
LnkSta: Speed unknown, Width x0, TrErr- Train- SlotClk- DLActive-
BWMgmt- ABWMgmt-
DevCap2: Completion Timeout: Not Supported, TimeoutDis-
DevCtl2: Completion Timeout: 50us to 50ms, TimeoutDis-
LnkCtl2: Target Link Speed: 2.5GT/s, EnterCompliance- SpeedDis-,
Selectable De-emphasis: -6dB
Transmit Margin: Normal Operating Range,
EnterModifiedCompliance-
ComplianceSOS-
Compliance De-emphasis: -6dB
LnkSta2: Current De-emphasis Level: -6dB
Capabilities: [a0] MSI: Enable+ Count=1/1 Maskable- 64bit+
Address: 00000000fee0300c Data: 4161
Capabilities: [100 v1] Vendor Specific Information: ID=0001
Rev=1 Len=010 <?>
Kernel driver in use: radeon
00:01.1 Audio device [0403]: ATI Technologies Inc Device [1002:1314]
Subsystem: ASUSTeK Computer Inc. Device [1043:101c]
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B- DisINTx+
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort-
<TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0, Cache Line Size: 64 bytes
Interrupt: pin B routed to IRQ 42
Region 0: Memory at feb44000 (32-bit, non-prefetchable) [size=16K]
Capabilities: [50] Power Management version 3
Flags: PMEClk- DSI- D1+ D2+ AuxCurrent=0mA
PME(D0-,D1-,D2-,D3hot-,D3cold-)
Status: D0 NoSoftRst- PME-Enable- DSel=0 DScale=0 PME-
Capabilities: [58] Express (v2) Root Complex Integrated Endpoint, MSI 00
DevCap: MaxPayload 128 bytes, PhantFunc 0, Latency L0s
<4us, L1 unlimited
ExtTag+ RBE+ FLReset-
DevCtl: Report errors: Correctable- Non-Fatal- Fatal-
Unsupported-
RlxdOrd+ ExtTag- PhantFunc- AuxPwr- NoSnoop+
MaxPayload 128 bytes, MaxReadReq 128 bytes
DevSta: CorrErr- UncorrErr- FatalErr- UnsuppReq-
AuxPwr- TransPend-
LnkCap: Port #0, Speed unknown, Width x0, ASPM unknown,
Latency L0
<64ns, L1 <1us
ClockPM- Surprise- LLActRep- BwNot-
LnkCtl: ASPM Disabled; Disabled- Retrain- CommClk-
ExtSynch- ClockPM- AutWidDis- BWInt- AutBWInt-
LnkSta: Speed unknown, Width x0, TrErr- Train- SlotClk- DLActive-
BWMgmt- ABWMgmt-
DevCap2: Completion Timeout: Not Supported, TimeoutDis-
DevCtl2: Completion Timeout: 50us to 50ms, TimeoutDis-
LnkCtl2: Target Link Speed: 2.5GT/s, EnterCompliance- SpeedDis-,
Selectable De-emphasis: -6dB
Transmit Margin: Normal Operating Range,
EnterModifiedCompliance-
ComplianceSOS-
Compliance De-emphasis: -6dB
LnkSta2: Current De-emphasis Level: -6dB
Capabilities: [a0] MSI: Enable+ Count=1/1 Maskable- 64bit+
Address: 00000000fee0300c Data: 4169
Capabilities: [100 v1] Vendor Specific Information: ID=0001
Rev=1 Len=010 <?>
Kernel driver in use: HDA Intel
00:04.0 PCI bridge [0604]: Advanced Micro Devices [AMD] Device
[1022:1512] (prog-if 00 [Normal decode])
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort-
<TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0, Cache Line Size: 64 bytes
Bus: primary=00, secondary=01, subordinate=01, sec-latency=0
I/O behind bridge: 0000e000-0000efff
Memory behind bridge: fea00000-feafffff
Prefetchable memory behind bridge: 00000000c0000000-00000000cfffffff
Secondary status: 66MHz- FastB2B- ParErr- DEVSEL=fast >TAbort-
<TAbort- <MAbort+ <SERR- <PERR-
BridgeCtl: Parity- SERR- NoISA- VGA- MAbort- >Reset- FastB2B-
PriDiscTmr- SecDiscTmr- DiscTmrStat- DiscTmrSERREn-
Capabilities: [50] Power Management version 3
Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA
PME(D0+,D1-,D2-,D3hot+,D3cold+)
Status: D0 NoSoftRst- PME-Enable- DSel=0 DScale=0 PME-
Capabilities: [58] Express (v2) Root Port (Slot+), MSI 00
DevCap: MaxPayload 128 bytes, PhantFunc 0, Latency L0s
<64ns, L1 <1us
ExtTag+ RBE+ FLReset-
DevCtl: Report errors: Correctable- Non-Fatal- Fatal-
Unsupported-
RlxdOrd- ExtTag- PhantFunc- AuxPwr- NoSnoop+
MaxPayload 128 bytes, MaxReadReq 128 bytes
DevSta: CorrErr- UncorrErr- FatalErr- UnsuppReq-
AuxPwr- TransPend-
LnkCap: Port #1, Speed 5GT/s, Width x4, ASPM L0s L1,
Latency L0 <64ns, L1 <1us
ClockPM- Surprise- LLActRep+ BwNot+
LnkCtl: ASPM L0s L1 Enabled; RCB 64 bytes Disabled-
Retrain- CommClk+
ExtSynch- ClockPM- AutWidDis- BWInt- AutBWInt-
LnkSta: Speed 5GT/s, Width x4, TrErr- Train- SlotClk+ DLActive+
BWMgmt+ ABWMgmt+
SltCap: AttnBtn- PwrCtrl- MRL- AttnInd- PwrInd-
HotPlug+ Surprise-
Slot #4, PowerLimit 75.000W; Interlock- NoCompl+
SltCtl: Enable: AttnBtn- PwrFlt- MRL- PresDet- CmdCplt-
HPIrq- LinkChg-
Control: AttnInd Unknown, PwrInd Unknown,
Power- Interlock-
SltSta: Status: AttnBtn- PowerFlt- MRL- CmdCplt-
PresDet+ Interlock-
Changed: MRL- PresDet+ LinkState+
RootCtl: ErrCorrectable- ErrNon-Fatal- ErrFatal-
PMEIntEna- CRSVisible-
RootCap: CRSVisible-
RootSta: PME ReqID 0000, PMEStatus- PMEPending-
DevCap2: Completion Timeout: Range ABCD, TimeoutDis+ ARIFwd-
DevCtl2: Completion Timeout: 65ms to 210ms, TimeoutDis- ARIFwd-
LnkCtl2: Target Link Speed: 5GT/s, EnterCompliance- SpeedDis-,
Selectable De-emphasis: -6dB
Transmit Margin: Normal Operating Range,
EnterModifiedCompliance-
ComplianceSOS-
Compliance De-emphasis: -6dB
LnkSta2: Current De-emphasis Level: -6dB
Capabilities: [a0] MSI: Enable- Count=1/1 Maskable- 64bit+
Address: 0000000000000000 Data: 0000
Capabilities: [b0] Subsystem: Advanced Micro Devices [AMD]
Device [1022:1234]
Capabilities: [b8] HyperTransport: MSI Mapping Enable+ Fixed+
Capabilities: [100 v1] Vendor Specific Information: ID=0001
Rev=1 Len=010 <?>
Kernel driver in use: pcieport
00:11.0 SATA controller [0106]: ATI Technologies Inc SB700/SB800 SATA
Controller [AHCI mode] [1002:4391] (rev 40) (prog-if 01 [AHCI 1.0])
Subsystem: ASUSTeK Computer Inc. Device [1043:101c]
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz+ UDF- FastB2B- ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 32
Interrupt: pin A routed to IRQ 19
Region 0: I/O ports at f190 [size=8]
Region 1: I/O ports at f180 [size=4]
Region 2: I/O ports at f170 [size=8]
Region 3: I/O ports at f160 [size=4]
Region 4: I/O ports at f150 [size=16]
Region 5: Memory at feb4f000 (32-bit, non-prefetchable) [size=1K]
Capabilities: [70] SATA HBA v1.0 InCfgSpace
Capabilities: [a4] PCI Advanced Features
AFCap: TP+ FLR+
AFCtrl: FLR-
AFStatus: TP-
Kernel driver in use: ahci
00:12.0 USB Controller [0c03]: ATI Technologies Inc SB700/SB800 USB
OHCI0 Controller [1002:4397] (prog-if 10 [OHCI])
Subsystem: ASUSTeK Computer Inc. Device [1043:101c]
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B- DisINTx-
Status: Cap- 66MHz+ UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 32, Cache Line Size: 64 bytes
Interrupt: pin A routed to IRQ 18
Region 0: Memory at feb4e000 (32-bit, non-prefetchable) [size=4K]
Kernel driver in use: ohci_hcd
00:12.2 USB Controller [0c03]: ATI Technologies Inc SB700/SB800 USB
EHCI Controller [1002:4396] (prog-if 20 [EHCI])
Subsystem: ASUSTeK Computer Inc. Device [1043:101c]
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV+ VGASnoop- ParErr-
Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz+ UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 32, Cache Line Size: 64 bytes
Interrupt: pin B routed to IRQ 17
Region 0: Memory at feb4d000 (32-bit, non-prefetchable) [size=256]
Capabilities: [c0] Power Management version 2
Flags: PMEClk- DSI- D1+ D2+ AuxCurrent=0mA
PME(D0+,D1+,D2+,D3hot+,D3cold-)
Status: D0 NoSoftRst- PME-Enable- DSel=0 DScale=0 PME-
Bridge: PM- B3+
Capabilities: [e4] Debug port: BAR=1 offset=00e0
Kernel driver in use: ehci_hcd
00:13.0 USB Controller [0c03]: ATI Technologies Inc SB700/SB800 USB
OHCI0 Controller [1002:4397] (prog-if 10 [OHCI])
Subsystem: ASUSTeK Computer Inc. Device [1043:101c]
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B- DisINTx-
Status: Cap- 66MHz+ UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 32, Cache Line Size: 64 bytes
Interrupt: pin A routed to IRQ 18
Region 0: Memory at feb4c000 (32-bit, non-prefetchable) [size=4K]
Kernel driver in use: ohci_hcd
00:13.2 USB Controller [0c03]: ATI Technologies Inc SB700/SB800 USB
EHCI Controller [1002:4396] (prog-if 20 [EHCI])
Subsystem: ASUSTeK Computer Inc. Device [1043:101c]
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV+ VGASnoop- ParErr-
Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz+ UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 32, Cache Line Size: 64 bytes
Interrupt: pin B routed to IRQ 17
Region 0: Memory at feb4b000 (32-bit, non-prefetchable) [size=256]
Capabilities: [c0] Power Management version 2
Flags: PMEClk- DSI- D1+ D2+ AuxCurrent=0mA
PME(D0+,D1+,D2+,D3hot+,D3cold-)
Status: D0 NoSoftRst- PME-Enable- DSel=0 DScale=0 PME-
Bridge: PM- B3+
Capabilities: [e4] Debug port: BAR=1 offset=00e0
Kernel driver in use: ehci_hcd
00:14.0 SMBus [0c05]: ATI Technologies Inc SBx00 SMBus Controller
[1002:4385] (rev 42)
Subsystem: ASUSTeK Computer Inc. Device [1043:101c]
Control: I/O+ Mem+ BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B- DisINTx+
Status: Cap- 66MHz+ UDF- FastB2B- ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR- INTx-
Kernel driver in use: piix4_smbus
00:14.1 IDE interface [0101]: ATI Technologies Inc SB700/SB800 IDE
Controller [1002:439c] (rev 40) (prog-if 8a [Master SecP PriP])
Subsystem: ASUSTeK Computer Inc. Device [1043:101c]
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B- DisINTx-
Status: Cap- 66MHz+ UDF- FastB2B- ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 32
Interrupt: pin B routed to IRQ 17
Region 0: I/O ports at 01f0 [size=8]
Region 1: I/O ports at 03f4 [size=1]
Region 2: I/O ports at 0170 [size=8]
Region 3: I/O ports at 0374 [size=1]
Region 4: I/O ports at f100 [size=16]
Kernel driver in use: pata_atiixp
00:14.2 Audio device [0403]: ATI Technologies Inc SBx00 Azalia (Intel
HDA) [1002:4383] (rev 40)
Subsystem: ASUSTeK Computer Inc. Device [1043:101c]
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=slow >TAbort-
<TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 32, Cache Line Size: 64 bytes
Interrupt: pin A routed to IRQ 16
Region 0: Memory at feb40000 (64-bit, non-prefetchable) [size=16K]
Capabilities: [50] Power Management version 2
Flags: PMEClk- DSI- D1- D2- AuxCurrent=55mA
PME(D0+,D1-,D2-,D3hot+,D3cold+)
Status: D0 NoSoftRst- PME-Enable- DSel=0 DScale=0 PME-
Kernel driver in use: HDA Intel
00:14.3 ISA bridge [0601]: ATI Technologies Inc SB700/SB800 LPC host
controller [1002:439d] (rev 40)
Subsystem: ASUSTeK Computer Inc. Device [1043:101c]
Control: I/O+ Mem+ BusMaster+ SpecCycle+ MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B- DisINTx-
Status: Cap- 66MHz+ UDF- FastB2B- ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0
00:14.4 PCI bridge [0604]: ATI Technologies Inc SBx00 PCI to PCI
Bridge [1002:4384] (rev 40) (prog-if 01 [Subtractive decode])
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop+ ParErr-
Stepping- SERR- FastB2B- DisINTx-
Status: Cap- 66MHz+ UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 64
Bus: primary=00, secondary=02, subordinate=02, sec-latency=64
Secondary status: 66MHz- FastB2B+ ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort+ <SERR- <PERR-
BridgeCtl: Parity- SERR- NoISA- VGA- MAbort- >Reset- FastB2B-
PriDiscTmr- SecDiscTmr- DiscTmrStat- DiscTmrSERREn-
00:14.5 USB Controller [0c03]: ATI Technologies Inc SB700/SB800 USB
OHCI2 Controller [1002:4399] (prog-if 10 [OHCI])
Subsystem: ASUSTeK Computer Inc. Device [1043:101c]
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B- DisINTx-
Status: Cap- 66MHz+ UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 32, Cache Line Size: 64 bytes
Interrupt: pin C routed to IRQ 18
Region 0: Memory at feb4a000 (32-bit, non-prefetchable) [size=4K]
Kernel driver in use: ohci_hcd
00:15.0 PCI bridge [0604]: ATI Technologies Inc Device [1002:43a0]
(prog-if 00 [Normal decode])
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort-
<TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0, Cache Line Size: 64 bytes
Bus: primary=00, secondary=03, subordinate=03, sec-latency=0
I/O behind bridge: 0000d000-0000dfff
Prefetchable memory behind bridge: 00000000d0000000-00000000d00fffff
Secondary status: 66MHz- FastB2B- ParErr- DEVSEL=fast >TAbort-
<TAbort- <MAbort- <SERR- <PERR-
BridgeCtl: Parity- SERR- NoISA- VGA- MAbort- >Reset- FastB2B-
PriDiscTmr- SecDiscTmr- DiscTmrStat- DiscTmrSERREn-
Capabilities: [50] Power Management version 3
Flags: PMEClk- DSI- D1+ D2+ AuxCurrent=0mA
PME(D0-,D1-,D2-,D3hot-,D3cold-)
Status: D0 NoSoftRst- PME-Enable- DSel=0 DScale=0 PME-
Capabilities: [58] Express (v2) Root Port (Slot-), MSI 00
DevCap: MaxPayload 128 bytes, PhantFunc 0, Latency L0s
<64ns, L1 <1us
ExtTag+ RBE+ FLReset-
DevCtl: Report errors: Correctable- Non-Fatal- Fatal-
Unsupported-
RlxdOrd- ExtTag- PhantFunc- AuxPwr- NoSnoop+
MaxPayload 128 bytes, MaxReadReq 128 bytes
DevSta: CorrErr- UncorrErr- FatalErr- UnsuppReq-
AuxPwr- TransPend-
LnkCap: Port #0, Speed 2.5GT/s, Width x1, ASPM L0s L1, Latency L0
<64ns, L1 <1us
ClockPM- Surprise- LLActRep+ BwNot+
LnkCtl: ASPM L1 Enabled; RCB 64 bytes Disabled- Retrain- CommClk+
ExtSynch- ClockPM- AutWidDis- BWInt- AutBWInt-
LnkSta: Speed 2.5GT/s, Width x1, TrErr- Train- SlotClk+ DLActive+
BWMgmt+ ABWMgmt-
RootCtl: ErrCorrectable- ErrNon-Fatal- ErrFatal-
PMEIntEna- CRSVisible-
RootCap: CRSVisible-
RootSta: PME ReqID 0000, PMEStatus- PMEPending-
DevCap2: Completion Timeout: Range ABCD, TimeoutDis+ ARIFwd-
DevCtl2: Completion Timeout: 65ms to 210ms, TimeoutDis- ARIFwd-
LnkCtl2: Target Link Speed: 2.5GT/s, EnterCompliance- SpeedDis-,
Selectable De-emphasis: -3.5dB
Transmit Margin: Normal Operating Range,
EnterModifiedCompliance-
ComplianceSOS-
Compliance De-emphasis: -6dB
LnkSta2: Current De-emphasis Level: -6dB
Capabilities: [a0] MSI: Enable- Count=1/1 Maskable- 64bit+
Address: 0000000000000000 Data: 0000
Capabilities: [b0] Subsystem: ATI Technologies Inc Device [1002:0000]
Capabilities: [b8] HyperTransport: MSI Mapping Enable+ Fixed+
Capabilities: [100 v1] Vendor Specific Information: ID=0001
Rev=1 Len=010 <?>
Kernel driver in use: pcieport
00:15.1 PCI bridge [0604]: ATI Technologies Inc Device [1002:43a1]
(prog-if 00 [Normal decode])
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort-
<TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0, Cache Line Size: 64 bytes
Bus: primary=00, secondary=04, subordinate=04, sec-latency=0
Memory behind bridge: fe900000-fe9fffff
Secondary status: 66MHz- FastB2B- ParErr- DEVSEL=fast >TAbort-
<TAbort- <MAbort- <SERR- <PERR-
BridgeCtl: Parity- SERR- NoISA- VGA- MAbort- >Reset- FastB2B-
PriDiscTmr- SecDiscTmr- DiscTmrStat- DiscTmrSERREn-
Capabilities: [50] Power Management version 3
Flags: PMEClk- DSI- D1+ D2+ AuxCurrent=0mA
PME(D0-,D1-,D2-,D3hot-,D3cold-)
Status: D0 NoSoftRst- PME-Enable- DSel=0 DScale=0 PME-
Capabilities: [58] Express (v2) Root Port (Slot-), MSI 00
DevCap: MaxPayload 128 bytes, PhantFunc 0, Latency L0s
<64ns, L1 <1us
ExtTag+ RBE+ FLReset-
DevCtl: Report errors: Correctable- Non-Fatal- Fatal-
Unsupported-
RlxdOrd- ExtTag- PhantFunc- AuxPwr- NoSnoop+
MaxPayload 128 bytes, MaxReadReq 128 bytes
DevSta: CorrErr- UncorrErr- FatalErr- UnsuppReq-
AuxPwr- TransPend-
LnkCap: Port #1, Speed 2.5GT/s, Width x1, ASPM L0s L1, Latency L0
<64ns, L1 <1us
ClockPM- Surprise- LLActRep+ BwNot+
LnkCtl: ASPM Disabled; RCB 64 bytes Disabled- Retrain- CommClk+
ExtSynch- ClockPM- AutWidDis- BWInt- AutBWInt-
LnkSta: Speed 2.5GT/s, Width x1, TrErr- Train- SlotClk+ DLActive+
BWMgmt+ ABWMgmt-
RootCtl: ErrCorrectable- ErrNon-Fatal- ErrFatal-
PMEIntEna- CRSVisible-
RootCap: CRSVisible-
RootSta: PME ReqID 0000, PMEStatus- PMEPending-
DevCap2: Completion Timeout: Range ABCD, TimeoutDis+ ARIFwd-
DevCtl2: Completion Timeout: 65ms to 210ms, TimeoutDis- ARIFwd-
LnkCtl2: Target Link Speed: 2.5GT/s, EnterCompliance- SpeedDis-,
Selectable De-emphasis: -3.5dB
Transmit Margin: Normal Operating Range,
EnterModifiedCompliance-
ComplianceSOS-
Compliance De-emphasis: -6dB
LnkSta2: Current De-emphasis Level: -6dB
Capabilities: [a0] MSI: Enable- Count=1/1 Maskable- 64bit+
Address: 0000000000000000 Data: 0000
Capabilities: [b0] Subsystem: ATI Technologies Inc Device [1002:0000]
Capabilities: [b8] HyperTransport: MSI Mapping Enable+ Fixed+
Capabilities: [100 v1] Vendor Specific Information: ID=0001
Rev=1 Len=010 <?>
Kernel driver in use: pcieport
00:16.0 USB Controller [0c03]: ATI Technologies Inc SB700/SB800 USB
OHCI0 Controller [1002:4397] (prog-if 10 [OHCI])
Subsystem: ASUSTeK Computer Inc. Device [1043:101c]
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B- DisINTx-
Status: Cap- 66MHz+ UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 32, Cache Line Size: 64 bytes
Interrupt: pin A routed to IRQ 18
Region 0: Memory at feb49000 (32-bit, non-prefetchable) [size=4K]
Kernel driver in use: ohci_hcd
00:16.2 USB Controller [0c03]: ATI Technologies Inc SB700/SB800 USB
EHCI Controller [1002:4396] (prog-if 20 [EHCI])
Subsystem: ASUSTeK Computer Inc. Device [1043:101c]
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV+ VGASnoop- ParErr-
Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz+ UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 32, Cache Line Size: 64 bytes
Interrupt: pin B routed to IRQ 17
Region 0: Memory at feb48000 (32-bit, non-prefetchable) [size=256]
Capabilities: [c0] Power Management version 2
Flags: PMEClk- DSI- D1+ D2+ AuxCurrent=0mA
PME(D0+,D1+,D2+,D3hot+,D3cold-)
Status: D0 NoSoftRst- PME-Enable- DSel=0 DScale=0 PME-
Bridge: PM- B3+
Capabilities: [e4] Debug port: BAR=1 offset=00e0
Kernel driver in use: ehci_hcd
00:18.0 Host bridge [0600]: Advanced Micro Devices [AMD] Family
12h/14h Processor Function 0 [1022:1700] (rev 43)
Control: I/O- Mem- BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort-
<TAbort- <MAbort- >SERR- <PERR- INTx-
00:18.1 Host bridge [0600]: Advanced Micro Devices [AMD] Family
12h/14h Processor Function 1 [1022:1701]
Control: I/O- Mem- BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B- DisINTx-
Status: Cap- 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort-
<TAbort- <MAbort- >SERR- <PERR- INTx-
00:18.2 Host bridge [0600]: Advanced Micro Devices [AMD] Family
12h/14h Processor Function 2 [1022:1702]
Control: I/O- Mem- BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B- DisINTx-
Status: Cap- 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort-
<TAbort- <MAbort- >SERR- <PERR- INTx-
00:18.3 Host bridge [0600]: Advanced Micro Devices [AMD] Family
12h/14h Processor Function 3 [1022:1703]
Control: I/O- Mem- BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort-
<TAbort- <MAbort- >SERR- <PERR- INTx-
Capabilities: [f0] Secure device <?>
Kernel driver in use: k10temp
00:18.4 Host bridge [0600]: Advanced Micro Devices [AMD] Family
12h/14h Processor Function 4 [1022:1704]
Control: I/O- Mem- BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B- DisINTx-
Status: Cap- 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort-
<TAbort- <MAbort- >SERR- <PERR- INTx-
00:18.5 Host bridge [0600]: Advanced Micro Devices [AMD] Family
12h/14h Processor Function 6 [1022:1718]
Control: I/O- Mem- BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B- DisINTx-
Status: Cap- 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort-
<TAbort- <MAbort- >SERR- <PERR- INTx-
00:18.6 Host bridge [0600]: Advanced Micro Devices [AMD] Family
12h/14h Processor Function 5 [1022:1716]
Control: I/O- Mem- BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B- DisINTx-
Status: Cap- 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort-
<TAbort- <MAbort- >SERR- <PERR- INTx-
00:18.7 Host bridge [0600]: Advanced Micro Devices [AMD] Family
12h/14h Processor Function 7 [1022:1719]
Control: I/O- Mem- BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B- DisINTx-
Status: Cap- 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort-
<TAbort- <MAbort- >SERR- <PERR- INTx-
01:00.0 VGA compatible controller [0300]: ATI Technologies Inc NI
Seymour [AMD Radeon HD 6470M] [1002:6760] (prog-if 00 [VGA
controller])
Subsystem: ASUSTeK Computer Inc. Device [1043:101c]
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B- DisINTx+
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort-
<TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0, Cache Line Size: 64 bytes
Interrupt: pin A routed to IRQ 43
Region 0: Memory at c0000000 (64-bit, prefetchable) [size=256M]
Region 2: Memory at fea20000 (64-bit, non-prefetchable) [size=128K]
Region 4: I/O ports at e000 [size=256]
Expansion ROM at fea00000 [disabled] [size=128K]
Capabilities: [50] Power Management version 3
Flags: PMEClk- DSI- D1+ D2+ AuxCurrent=0mA
PME(D0-,D1-,D2-,D3hot-,D3cold-)
Status: D0 NoSoftRst- PME-Enable- DSel=0 DScale=0 PME-
Capabilities: [58] Express (v2) Legacy Endpoint, MSI 00
DevCap: MaxPayload 256 bytes, PhantFunc 0, Latency L0s
<4us, L1 unlimited
ExtTag+ AttnBtn- AttnInd- PwrInd- RBE+ FLReset-
DevCtl: Report errors: Correctable- Non-Fatal- Fatal-
Unsupported-
RlxdOrd- ExtTag- PhantFunc- AuxPwr- NoSnoop+
MaxPayload 128 bytes, MaxReadReq 128 bytes
DevSta: CorrErr+ UncorrErr- FatalErr- UnsuppReq+
AuxPwr- TransPend-
LnkCap: Port #1, Speed 5GT/s, Width x16, ASPM L0s L1, Latency L0
<64ns, L1 <1us
ClockPM- Surprise- LLActRep- BwNot-
LnkCtl: ASPM L0s L1 Enabled; RCB 64 bytes Disabled-
Retrain- CommClk+
ExtSynch- ClockPM- AutWidDis- BWInt- AutBWInt-
LnkSta: Speed 5GT/s, Width x4, TrErr- Train- SlotClk+ DLActive-
BWMgmt- ABWMgmt-
DevCap2: Completion Timeout: Not Supported, TimeoutDis-
DevCtl2: Completion Timeout: 50us to 50ms, TimeoutDis-
LnkCtl2: Target Link Speed: 5GT/s, EnterCompliance- SpeedDis-,
Selectable De-emphasis: -6dB
Transmit Margin: Normal Operating Range,
EnterModifiedCompliance-
ComplianceSOS-
Compliance De-emphasis: -6dB
LnkSta2: Current De-emphasis Level: -6dB
Capabilities: [a0] MSI: Enable+ Count=1/1 Maskable- 64bit+
Address: 00000000fee0300c Data: 4171
Capabilities: [100 v1] Vendor Specific Information: ID=0001
Rev=1 Len=010 <?>
Capabilities: [150 v1] Advanced Error Reporting
UESta: DLP- SDES- TLP- FCP- CmpltTO- CmpltAbrt- UnxCmplt- RxOF-
MalfTLP- ECRC- UnsupReq- ACSViol-
UEMsk: DLP- SDES- TLP- FCP- CmpltTO- CmpltAbrt- UnxCmplt- RxOF-
MalfTLP- ECRC- UnsupReq- ACSViol-
UESvrt: DLP+ SDES+ TLP- FCP+ CmpltTO- CmpltAbrt- UnxCmplt- RxOF+
MalfTLP+ ECRC- UnsupReq- ACSViol-
CESta: RxErr- BadTLP- BadDLLP- Rollover- Timeout- NonFatalErr+
CEMsk: RxErr- BadTLP- BadDLLP- Rollover- Timeout- NonFatalErr+
AERCap: First Error Pointer: 00, GenCap- CGenEn- ChkCap+ ChkEn-
Kernel driver in use: radeon
03:00.0 Ethernet controller [0200]: Realtek Semiconductor Co., Ltd.
RTL8111/8168B PCI Express Gigabit Ethernet controller [10ec:8168] (rev
06)
Subsystem: ASUSTeK Computer Inc. Device [1043:101c]
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B- DisINTx+
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort-
<TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0, Cache Line Size: 64 bytes
Interrupt: pin A routed to IRQ 40
Region 0: I/O ports at d000 [size=256]
Region 2: Memory at d0004000 (64-bit, prefetchable) [size=4K]
Region 4: Memory at d0000000 (64-bit, prefetchable) [size=16K]
Capabilities: [40] Power Management version 3
Flags: PMEClk- DSI- D1+ D2+ AuxCurrent=375mA
PME(D0+,D1+,D2+,D3hot+,D3cold+)
Status: D0 NoSoftRst+ PME-Enable- DSel=0 DScale=0 PME-
Capabilities: [50] MSI: Enable+ Count=1/1 Maskable- 64bit+
Address: 00000000fee0300c Data: 4141
Capabilities: [70] Express (v2) Endpoint, MSI 01
DevCap: MaxPayload 128 bytes, PhantFunc 0, Latency L0s
<512ns, L1 <64us
ExtTag- AttnBtn- AttnInd- PwrInd- RBE+ FLReset-
DevCtl: Report errors: Correctable- Non-Fatal- Fatal-
Unsupported-
RlxdOrd- ExtTag- PhantFunc- AuxPwr- NoSnoop-
MaxPayload 128 bytes, MaxReadReq 4096 bytes
DevSta: CorrErr- UncorrErr- FatalErr- UnsuppReq-
AuxPwr+ TransPend-
LnkCap: Port #0, Speed 2.5GT/s, Width x1, ASPM L0s L1, Latency L0
unlimited, L1 <64us
ClockPM+ Surprise- LLActRep- BwNot-
LnkCtl: ASPM L1 Enabled; RCB 64 bytes Disabled- Retrain- CommClk+
ExtSynch- ClockPM- AutWidDis- BWInt- AutBWInt-
LnkSta: Speed 2.5GT/s, Width x1, TrErr- Train- SlotClk+ DLActive-
BWMgmt- ABWMgmt-
DevCap2: Completion Timeout: Range ABCD, TimeoutDis+
DevCtl2: Completion Timeout: 50us to 50ms, TimeoutDis-
LnkCtl2: Target Link Speed: 2.5GT/s, EnterCompliance- SpeedDis-,
Selectable De-emphasis: -6dB
Transmit Margin: Normal Operating Range,
EnterModifiedCompliance-
ComplianceSOS-
Compliance De-emphasis: -6dB
LnkSta2: Current De-emphasis Level: -6dB
Capabilities: [b0] MSI-X: Enable- Count=4 Masked-
Vector table: BAR=4 offset=00000000
PBA: BAR=4 offset=00000800
Capabilities: [d0] Vital Product Data
No end tag found
Capabilities: [100 v1] Advanced Error Reporting
UESta: DLP- SDES- TLP- FCP- CmpltTO+ CmpltAbrt- UnxCmplt- RxOF-
MalfTLP- ECRC- UnsupReq- ACSViol-
UEMsk: DLP- SDES- TLP- FCP- CmpltTO- CmpltAbrt- UnxCmplt- RxOF-
MalfTLP- ECRC- UnsupReq- ACSViol-
UESvrt: DLP+ SDES+ TLP- FCP+ CmpltTO- CmpltAbrt- UnxCmplt- RxOF+
MalfTLP+ ECRC- UnsupReq- ACSViol-
CESta: RxErr- BadTLP- BadDLLP- Rollover- Timeout- NonFatalErr-
CEMsk: RxErr- BadTLP- BadDLLP- Rollover- Timeout- NonFatalErr+
AERCap: First Error Pointer: 0e, GenCap+ CGenEn- ChkCap+ ChkEn-
Capabilities: [140 v1] Virtual Channel
Caps: LPEVC=0 RefClk=100ns PATEntryBits=1
Arb: Fixed- WRR32- WRR64- WRR128-
Ctrl: ArbSelect=Fixed
Status: InProgress-
VC0: Caps: PATOffset=00 MaxTimeSlots=1 RejSnoopTrans-
Arb: Fixed- WRR32- WRR64- WRR128- TWRR128- WRR256-
Ctrl: Enable+ ID=0 ArbSelect=Fixed TC/VC=01
Status: NegoPending- InProgress-
Capabilities: [160 v1] Device Serial Number 56-00-00-00-68-4c-e0-00
Kernel driver in use: r8169
04:00.0 Network controller [0280]: Atheros Communications Inc. AR9285
Wireless Network Adapter (PCI-Express) [168c:002b] (rev 01)
Subsystem: AzureWave Device [1a3b:1089]
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort-
<TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0, Cache Line Size: 64 bytes
Interrupt: pin A routed to IRQ 17
Region 0: Memory at fe900000 (64-bit, non-prefetchable) [size=64K]
Capabilities: [40] Power Management version 3
Flags: PMEClk- DSI- D1+ D2- AuxCurrent=375mA
PME(D0+,D1+,D2-,D3hot+,D3cold+)
Status: D0 NoSoftRst- PME-Enable- DSel=0 DScale=0 PME-
Capabilities: [50] MSI: Enable- Count=1/1 Maskable- 64bit-
Address: 00000000 Data: 0000
Capabilities: [60] Express (v2) Legacy Endpoint, MSI 00
DevCap: MaxPayload 128 bytes, PhantFunc 0, Latency L0s
<512ns, L1 <64us
ExtTag- AttnBtn- AttnInd- PwrInd- RBE+ FLReset-
DevCtl: Report errors: Correctable- Non-Fatal- Fatal-
Unsupported-
RlxdOrd- ExtTag- PhantFunc- AuxPwr- NoSnoop-
MaxPayload 128 bytes, MaxReadReq 128 bytes
DevSta: CorrErr- UncorrErr+ FatalErr- UnsuppReq-
AuxPwr+ TransPend-
LnkCap: Port #0, Speed 2.5GT/s, Width x1, ASPM L0s L1, Latency L0
<512ns, L1 <64us
ClockPM- Surprise- LLActRep- BwNot-
LnkCtl: ASPM Disabled; RCB 64 bytes Disabled- Retrain- CommClk+
ExtSynch- ClockPM- AutWidDis- BWInt- AutBWInt-
LnkSta: Speed 2.5GT/s, Width x1, TrErr- Train- SlotClk+ DLActive-
BWMgmt- ABWMgmt-
DevCap2: Completion Timeout: Not Supported, TimeoutDis+
DevCtl2: Completion Timeout: 50us to 50ms, TimeoutDis-
LnkCtl2: Target Link Speed: 2.5GT/s, EnterCompliance- SpeedDis-,
Selectable De-emphasis: -6dB
Transmit Margin: Normal Operating Range,
EnterModifiedCompliance-
ComplianceSOS-
Compliance De-emphasis: -6dB
LnkSta2: Current De-emphasis Level: -6dB
Capabilities: [100 v1] Advanced Error Reporting
UESta: DLP- SDES- TLP- FCP- CmpltTO+ CmpltAbrt- UnxCmplt- RxOF-
MalfTLP- ECRC- UnsupReq- ACSViol-
UEMsk: DLP- SDES- TLP- FCP- CmpltTO- CmpltAbrt- UnxCmplt- RxOF-
MalfTLP- ECRC- UnsupReq- ACSViol-
UESvrt: DLP+ SDES+ TLP- FCP+ CmpltTO- CmpltAbrt- UnxCmplt- RxOF+
MalfTLP+ ECRC- UnsupReq- ACSViol-
CESta: RxErr- BadTLP- BadDLLP- Rollover- Timeout- NonFatalErr-
CEMsk: RxErr- BadTLP- BadDLLP- Rollover- Timeout- NonFatalErr+
AERCap: First Error Pointer: 0e, GenCap+ CGenEn- ChkCap+ ChkEn-
Capabilities: [140 v1] Virtual Channel
Caps: LPEVC=0 RefClk=100ns PATEntryBits=1
Arb: Fixed- WRR32- WRR64- WRR128-
Ctrl: ArbSelect=Fixed
Status: InProgress-
VC0: Caps: PATOffset=00 MaxTimeSlots=1 RejSnoopTrans-
Arb: Fixed- WRR32- WRR64- WRR128- TWRR128- WRR256-
Ctrl: Enable+ ID=0 ArbSelect=Fixed TC/VC=01
Status: NegoPending- InProgress-
Capabilities: [160 v1] Device Serial Number 00-15-17-ff-ff-24-14-12
Capabilities: [170 v1] Power Budgeting <?>
Kernel driver in use: ath9k
** USB devices:
Bus 007 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub
Bus 006 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub
Bus 005 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub
Bus 004 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub
Bus 003 Device 001: ID 1d6b:0002 Linux Foundation 2.0 root hub
Bus 002 Device 001: ID 1d6b:0002 Linux Foundation 2.0 root hub
Bus 001 Device 003: ID 0bda:0138 Realtek Semiconductor Corp.
Bus 001 Device 002: ID 04f2:b23b Chicony Electronics Co., Ltd
Bus 001 Device 001: ID 1d6b:0002 Linux Foundation 2.0 root hub
-- System Information:
Debian Release: 6.0.2
APT prefers stable-updates
APT policy: (990, 'stable-updates'), (990, 'stable'), (101,
'testing'), (99, 'testing'), (98, 'unstable'), (97, 'experimental')
Architecture: amd64 (x86_64)
Kernel: Linux 2.6.39-bpo.2-amd64 (SMP w/2 CPU cores)
Locale: LANG=ru_RU.UTF-8, LC_CTYPE=ru_RU.UTF-8 (charmap=UTF-8)
Shell: /bin/sh linked to /bin/dash
Versions of packages linux-image-2.6.39-bpo.2-amd64 depends on:
ii debconf [debconf-2.0] 1.5.36.1 Debian configuration management sy
ii initramfs-tools [linux-init 0.99~bpo60+1 tools for generating an initramfs
ii linux-base 3.3~bpo60+1 Linux image base package
ii module-init-tools 3.12-1 tools for managing Linux kernel mo
Versions of packages linux-image-2.6.39-bpo.2-amd64 recommends:
ii firmware-linux-free 2.6.32-35squeeze2 Binary firmware for various driver
Versions of packages linux-image-2.6.39-bpo.2-amd64 suggests:
ii grub-pc 1.98+20100804-14 GRand Unified Bootloader, version
pn linux-doc-2.6.39 <none> (no description available)
Versions of packages linux-image-2.6.39-bpo.2-amd64 is related to:
pn firmware-bnx2 <none> (no description available)
pn firmware-bnx2x <none> (no description available)
pn firmware-ipw2x00 <none> (no description available)
pn firmware-ivtv <none> (no description available)
pn firmware-iwlwifi <none> (no description available)
ii firmware-linux 0.32~bpo60+1 Binary firmware for various driver
ii firmware-linux-nonfree 0.32~bpo60+1 Binary firmware for various driver
pn firmware-qlogic <none> (no description available)
pn firmware-ralink <none> (no description available)
pn xen-hypervisor <none> (no description available)
-- debconf information:
linux-image-2.6.39-bpo.2-amd64/postinst/missing-firmware-2.6.39-bpo.2-amd64:
linux-image-2.6.39-bpo.2-amd64/postinst/ignoring-ramdisk:
linux-image-2.6.39-bpo.2-amd64/postinst/depmod-error-initrd-2.6.39-bpo.2-amd64:
false
linux-image-2.6.39-bpo.2-amd64/prerm/removing-running-kernel-2.6.39-bpo.2-amd64:
true
Reply to: