Bug#615609: linux-image-2.6.37-1-loongson-2: Lemote mini-pc with linux-image-2.6.37-1-loongson-2 doesn't support external usb NIC (TU2-ET100)
Wu Zhangjin,
Do you think you can have a look at the bug report below.
* Javier Vasquez <j.e.vasquez.v@gmail.com> [2011-02-27 12:19]:
> Package: linux-2.6
> Version: 2.6.37-1
> File: linux-image-2.6.37-1-loongson-2
> Severity: important
> Tags: upstream
>
> *** Please type your report below this line ***
>
> I have a lemote mini-pc loongson-2f, and when hooking an external usb
> NIC, the trendenet TU2-ET100, after disabling the inner NIC (realtek),
> then the device starts working nice for a while and then all of a
> sudden it just halts, and doing ifdown/ifup combination several times
> doesn't seem to be able to bring it up.
>
> I believe this problem is not exclusive to debian given that I've
> tried the gnew-sense 2.6.37 kernel, and another one from anheng, and
> none seems to work for this. Perhaps it exposes a HW problem, such
> the one for the inner NIC which can't handle checksums, and the CPU
> needs to deal with them (/sbin/ethtool -K eth0 rx off), but if it's a
> HW problem there might be a way to work around it (such as some
> usb-net or asix modules parameters). I'm not aware of any known
> problem related to this, so the first suspect is a kernel problem
> associated to the usb-net or the asix modules, which are the ones
> loaded for this external USB device. Perhaps for lemote HW there are
> some specific compile options required, and maybe missing, :-)
>
> Please notice the kernel was loaded with "debug" boot parameter, and
> even by doing so, the kernel log only shows the following associated
> to this problem:
>
> [ 68.076000] usb 1-1: new high speed USB device using ehci_hcd and address 4
> [ 68.220000] usb 1-1: New USB device found, idVendor=0b95, idProduct=7720
> [ 68.220000] usb 1-1: New USB device strings: Mfr=1, Product=2, SerialNumber=3
> [ 68.220000] usb 1-1: Product: AX88772
> [ 68.220000] usb 1-1: Manufacturer: ASIX Elec. Corp.
> [ 68.220000] usb 1-1: SerialNumber: 000001
> [ 69.164000] asix 1-1:1.0: eth1: register 'asix' at
> usb-0000:00:0e.5-1, ASIX AX88772 USB 2.0 Ethernet, 00:50:b6:08:1c:5f
> [ 69.164000] usbcore: registered new interface driver asix
> [ 173.484000] eth1: link up, 100Mbps, full-duplex, lpa 0x45E1
> [ 173.620000] eth1: link up, 100Mbps, full-duplex, lpa 0x45E1
> [ 184.120000] eth1: no IPv6 routers present
> [ 593.268000] ehci_hcd 0000:00:0e.5: force halt; handshake
> 9000000050071014 00004000 00000000 -> -145
> [ 593.268000] ehci_hcd 0000:00:0e.5: can't reschedule qh
> 98000000bc2d5200, err -145
> [ 593.268000] ehci_hcd 0000:00:0e.5: force halt; handshake
> 9000000050071014 00004000 00004000 -> -145
> [ 593.268000] ehci_hcd 0000:00:0e.5: HC died; cleaning up
> [ 593.272000] usb 1-1: USB disconnect, address 4
> [ 593.280000] asix 1-1:1.0: eth1: unregister 'asix'
> usb-0000:00:0e.5-1, ASIX AX88772 USB 2.0 Ethernet
>
> While this is still a problem, the mini-pc is of not much usage to me,
> given that its aimed to work as a two NICs gateway (and light server
> for couple of light services). The ineer NIC is working now after the
> work around for the checksum (inner NIC can handle the checks), but
> I'm still missing the external usb NIC to work...
>
> Below is additional information...
>
>
> -- Package-specific info:
> ** Version:
> Linux version 2.6.37-1-loongson-2f (Debian 2.6.37-1)
> (ben@decadent.org.uk) (gcc version 4.4.5 (Debian 4.4.5-2) ) #1 Wed Feb
> 16 17:37:56 UTC 2011
>
> ** Command line:
> console=tty no_auto_cmd root=/dev/sda6 resume=/dev/sda5 debug
> PMON_VER=LM6004-1.3.6 EC_VER=undefined machtype=lemote-fuloong-2f-box
>
> ** Not tainted
>
> ** Kernel log:
> [ 5.288000] usb usb2: New USB device found, idVendor=1d6b, idProduct=0001
> [ 5.292000] usb usb2: New USB device strings: Mfr=3, Product=2,
> SerialNumber=1
> [ 5.296000] usb usb2: Product: OHCI Host Controller
> [ 5.300000] usb usb2: Manufacturer: Linux 2.6.37-1-loongson-2f ohci_hcd
> [ 5.304000] usb usb2: SerialNumber: 0000:00:0e.4
> [ 5.312000] hub 2-0:1.0: USB hub found
> [ 5.316000] hub 2-0:1.0: 4 ports detected
> [ 5.596000] PCI: Setting latency timer of device 0000:00:0e.3 to 64
> [ 5.680000] usbcore: registered new interface driver usbserial
> [ 5.688000] USB Serial support registered for generic
> [ 5.716000] usb 2-3: new low speed USB device using ohci_hcd and address 2
> [ 5.944000] usb 2-3: New USB device found, idVendor=04d9, idProduct=1702
> [ 5.952000] usb 2-3: New USB device strings: Mfr=1, Product=2, SerialNumber=0
> [ 5.956000] usb 2-3: Product: USB Keyboard
> [ 5.960000] usb 2-3: Manufacturer:
> [ 6.272000] usb 2-4: new low speed USB device using ohci_hcd and address 3
> [ 6.496000] usb 2-4: New USB device found, idVendor=0458, idProduct=003a
> [ 6.500000] usb 2-4: New USB device strings: Mfr=1, Product=2, SerialNumber=0
> [ 6.504000] usb 2-4: Product: Optical Mouse
> [ 6.508000] usb 2-4: Manufacturer: Genius
> [ 6.612000] input: USB Keyboard as
> /devices/pci0000:00/0000:00:0e.4/usb2/2-3/2-3:1.0/input/input0
> [ 6.628000] generic-usb 0003:04D9:1702.0001: input,hidraw0: USB HID
> v1.10 Keyboard [ USB Keyboard] on usb-0000:00:0e.4-3/input0
> [ 6.652000] usbcore: registered new interface driver usbserial_generic
> [ 6.656000] usbserial: USB Serial Driver core
> [ 6.684000] input: USB Keyboard as
> /devices/pci0000:00/0000:00:0e.4/usb2/2-3/2-3:1.1/input/input1
> [ 6.704000] generic-usb 0003:04D9:1702.0002: input,hidraw1: USB HID
> v1.10 Device [ USB Keyboard] on usb-0000:00:0e.4-3/input1
> [ 6.736000] input: Genius Optical Mouse as
> /devices/pci0000:00/0000:00:0e.4/usb2/2-4/2-4:1.0/input/input2
> [ 6.756000] generic-usb 0003:0458:003A.0003: input,hidraw2: USB HID
> v1.11 Mouse [Genius Optical Mouse] on usb-0000:00:0e.4-4/input0
> [ 6.776000] usbcore: registered new interface driver usbhid
> [ 6.780000] usbhid: USB HID core driver
> [ 7.768000] USB Serial support registered for GSM modem (1-port)
> [ 7.888000] usbcore: registered new interface driver option
> [ 7.892000] option: v0.7.2:USB Driver for GSM modems
> [ 9.228000] Adding 3903744k swap on /dev/sda5. Priority:-1
> extents:1 across:3903744k
> [ 10.120000] EXT3-fs (sda6): using internal journal
> [ 10.476000] loop: module loaded
> [ 10.712000] fuse init (API version 7.15)
> [ 15.388000] EXT3-fs: barriers not enabled
> [ 15.404000] kjournald starting. Commit interval 5 seconds
> [ 15.412000] EXT3-fs (sda1): using internal journal
> [ 15.416000] EXT3-fs (sda1): mounted filesystem with ordered data mode
> [ 15.528000] EXT3-fs: barriers not enabled
> [ 15.548000] kjournald starting. Commit interval 5 seconds
> [ 15.552000] EXT3-fs (sda7): using internal journal
> [ 15.556000] EXT3-fs (sda7): mounted filesystem with ordered data mode
> [ 15.672000] EXT3-fs: barriers not enabled
> [ 15.688000] kjournald starting. Commit interval 5 seconds
> [ 15.692000] EXT3-fs (sda8): using internal journal
> [ 15.696000] EXT3-fs (sda8): mounted filesystem with ordered data mode
> [ 15.776000] EXT3-fs: barriers not enabled
> [ 15.792000] kjournald starting. Commit interval 5 seconds
> [ 15.800000] EXT3-fs (sda9): using internal journal
> [ 15.804000] EXT3-fs (sda9): mounted filesystem with ordered data mode
> [ 15.884000] EXT3-fs: barriers not enabled
> [ 15.896000] kjournald starting. Commit interval 5 seconds
> [ 15.900000] EXT3-fs (sda10): using internal journal
> [ 15.904000] EXT3-fs (sda10): mounted filesystem with ordered data mode
> [ 15.968000] EXT3-fs: barriers not enabled
> [ 15.984000] kjournald starting. Commit interval 5 seconds
> [ 15.988000] EXT3-fs (sda11): using internal journal
> [ 15.992000] EXT3-fs (sda11): mounted filesystem with ordered data mode
> [ 16.076000] EXT3-fs: barriers not enabled
> [ 16.096000] kjournald starting. Commit interval 5 seconds
> [ 16.100000] EXT3-fs (sda12): using internal journal
> [ 16.104000] EXT3-fs (sda12): mounted filesystem with ordered data mode
> [ 16.216000] EXT3-fs: barriers not enabled
> [ 16.240000] kjournald starting. Commit interval 5 seconds
> [ 16.244000] EXT3-fs (sda13): using internal journal
> [ 16.248000] EXT3-fs (sda13): mounted filesystem with ordered data mode
> [ 16.352000] EXT3-fs: barriers not enabled
> [ 16.372000] kjournald starting. Commit interval 5 seconds
> [ 16.376000] EXT3-fs (sda14): using internal journal
> [ 16.380000] EXT3-fs (sda14): mounted filesystem with ordered data mode
> [ 17.404000] r8169 0000:00:06.0: eth0: link up
> [ 30.188000] NET: Registered protocol family 10
> [ 30.196000] lo: Disabled Privacy Extensions
> [ 40.640000] eth0: no IPv6 routers present
> [ 68.076000] usb 1-1: new high speed USB device using ehci_hcd and address 4
> [ 68.220000] usb 1-1: New USB device found, idVendor=0b95, idProduct=7720
> [ 68.220000] usb 1-1: New USB device strings: Mfr=1, Product=2, SerialNumber=3
> [ 68.220000] usb 1-1: Product: AX88772
> [ 68.220000] usb 1-1: Manufacturer: ASIX Elec. Corp.
> [ 68.220000] usb 1-1: SerialNumber: 000001
> [ 69.164000] asix 1-1:1.0: eth1: register 'asix' at
> usb-0000:00:0e.5-1, ASIX AX88772 USB 2.0 Ethernet, 00:50:b6:08:1c:5f
> [ 69.164000] usbcore: registered new interface driver asix
> [ 173.484000] eth1: link up, 100Mbps, full-duplex, lpa 0x45E1
> [ 173.620000] eth1: link up, 100Mbps, full-duplex, lpa 0x45E1
> [ 184.120000] eth1: no IPv6 routers present
> [ 593.268000] ehci_hcd 0000:00:0e.5: force halt; handshake
> 9000000050071014 00004000 00000000 -> -145
> [ 593.268000] ehci_hcd 0000:00:0e.5: can't reschedule qh
> 98000000bc2d5200, err -145
> [ 593.268000] ehci_hcd 0000:00:0e.5: force halt; handshake
> 9000000050071014 00004000 00004000 -> -145
> [ 593.268000] ehci_hcd 0000:00:0e.5: HC died; cleaning up
> [ 593.272000] usb 1-1: USB disconnect, address 4
> [ 593.280000] asix 1-1:1.0: eth1: unregister 'asix'
> usb-0000:00:0e.5-1, ASIX AX88772 USB 2.0 Ethernet
> [ 638.768000] r8169 0000:00:06.0: eth0: link up
> [ 649.008000] eth0: no IPv6 routers present
> [ 936.700000] ioctl32(Xorg:4238): Unknown cmd fd(8)
> cmd(8004f300){t:'�';sz:4} arg(7f7f9d64) on /dev/fb0
> [ 936.700000] ioctl32(Xorg:4238): Unknown cmd fd(8)
> cmd(80046ef8){t:'n';sz:4} arg(007a1920) on /dev/fb0
> [ 936.704000] sisfb 0000:00:08.0: Invalid ROM contents
> [ 1015.748000] snd-malloc: invalid device type 0
>
> ** Model information
> system type : lemote-fuloong-2f-box
> cpu model : ICT Loongson-2 V0.3 FPU V0.1
>
> ** Loaded modules:
> Module Size Used by
> asix 18116 0
> usbnet 19082 1 asix
> ipv6 372239 14
> cpufreq_userspace 2144 0
> cpufreq_conservative 10876 0
> cpufreq_stats 3064 0
> cpufreq_powersave 1094 0
> autofs4 28456 2
> fuse 78107 1
> loop 18822 0
> option 16642 0
> evdev 12121 2
> usb_wwan 11359 1 option
> usbhid 45527 0
> hid 88104 1 usbhid
> usbserial 35706 2 option,usb_wwan
> snd_cs5535audio 11875 0
> snd_ac97_codec 132979 1 snd_cs5535audio
> ac97_bus 1294 1 snd_ac97_codec
> snd_pcm 89131 2 snd_cs5535audio,snd_ac97_codec
> snd_seq 64184 0
> ohci_hcd 25184 0
> ehci_hcd 45107 0
> snd_timer 23423 2 snd_pcm,snd_seq
> snd_seq_device 7061 1 snd_seq
> usbcore 175295 9
> asix,usbnet,option,usb_wwan,usbhid,usbserial,ohci_hcd,ehci_hcd
> snd 73711 6
> snd_cs5535audio,snd_ac97_codec,snd_pcm,snd_seq,snd_timer,snd_seq_device
> r8169 40348 0
> loongson2_cpufreq 2843 0
> soundcore 5903 1 snd
> loongson2_clock 2568 1 loongson2_cpufreq
> mii 4730 3 asix,usbnet,r8169
> rtc_cmos 8329 0
> nls_base 7329 1 usbcore
> snd_page_alloc 7053 2 snd_cs5535audio,snd_pcm
>
> ** Network interface configuration:
>
> auto lo
> iface lo inet loopback
>
> auto eth0
> allow-hotplug eth0
> iface eth0 inet static
> pre-up /sbin/ethtool -K eth0 rx off
> address 192.168.2.115
> netmask 255.255.255.0
> network 192.168.2.0
> broadcast 192.168.2.255
> gateway 192.168.2.1
> dns-nameservers 200.91.75.5 200.91.75.6 192.168.2.1
> dns-search local
>
> iface eth1 inet static
> address 192.168.2.115
> netmask 255.255.255.0
> network 192.168.2.0
> broadcast 192.168.2.255
> gateway 192.168.2.1
> dns-nameservers 200.91.75.5 200.91.75.6 192.168.2.1
> dns-search local
>
> ** Network status:
> *** IP interfaces and addresses:
> 1: lo: <LOOPBACK,UP,LOWER_UP> mtu 16436 qdisc noqueue state UNKNOWN
> link/loopback 00:00:00:00:00:00 brd 00:00:00:00:00:00
> inet 127.0.0.1/8 scope host lo
> inet6 ::1/128 scope host
> valid_lft forever preferred_lft forever
> 2: eth0: <BROADCAST,MULTICAST,UP,LOWER_UP> mtu 1500 qdisc pfifo_fast
> state UNKNOWN qlen 1000
> link/ether 00:23:9e:00:04:b6 brd ff:ff:ff:ff:ff:ff
> inet 192.168.2.115/24 brd 192.168.2.255 scope global eth0
> inet6 fe80::223:9eff:fe00:4b6/64 scope link
> valid_lft forever preferred_lft forever
>
> *** Device statistics:
> Inter-| Receive | Transmit
> face |bytes packets errs drop fifo frame compressed
> multicast|bytes packets errs drop fifo colls carrier compressed
> lo: 560 8 0 0 0 0 0 0
> 560 8 0 0 0 0 0 0
> eth0: 611120 891 0 0 0 0 0 0
> 226227 971 0 0 0 0 0 0
>
> *** Protocol statistics:
> Ip:
> 11717 total packets received
> 0 forwarded
> 0 incoming packets discarded
> 11717 incoming packets delivered
> 7920 requests sent out
> 36 dropped because of missing route
> Icmp:
> 27 ICMP messages received
> 0 input ICMP message failed.
> ICMP input histogram:
> destination unreachable: 1
> echo replies: 26
> 26 ICMP messages sent
> 0 ICMP messages failed
> ICMP output histogram:
> echo request: 26
> IcmpMsg:
> InType0: 26
> InType3: 1
> OutType8: 26
> Tcp:
> 33 active connections openings
> 0 passive connection openings
> 0 failed connection attempts
> 1 connection resets received
> 4 connections established
> 11570 segments received
> 7772 segments send out
> 2 segments retransmited
> 0 bad segments received.
> 4 resets sent
> Udp:
> 120 packets received
> 0 packets to unknown port received.
> 0 packet receive errors
> 120 packets sent
> UdpLite:
> TcpExt:
> 8 TCP sockets finished time wait in fast timer
> 55 delayed acks sent
> 8902 packet headers predicted
> 127 acknowledgments not containing data payload received
> 16 predicted acknowledgments
> 2 retransmits in slow start
> 1 connections reset due to early user close
> TCPSackShiftFallback: 1
> IpExt:
> InOctets: 16652854
> OutOctets: 640001
>
> *** Device features:
> eth0: 0x180
> lo: 0x13865
>
> ** PCI devices:
> 00:06.0 Ethernet controller [0200]: Realtek Semiconductor Co., Ltd.
> RTL-8169 Gigabit Ethernet [10ec:8169] (rev 10)
> Subsystem: Realtek Semiconductor Co., Ltd. RTL8169/8110 Family
> PCI Gigabit Ethernet NIC [10ec:8169]
> Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV+ VGASnoop-
> ParErr+ Stepping- SERR- FastB2B- DisINTx-
> Status: Cap+ 66MHz+ UDF- FastB2B+ ParErr- DEVSEL=medium
> >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
> Latency: 64 (8000ns min, 16000ns max), Cache Line Size: 32 bytes
> Interrupt: pin A routed to IRQ 36
> Region 0: I/O ports at 4000 [size=256]
> Region 1: Memory at 50072000 (32-bit, non-prefetchable) [size=256]
> Expansion ROM at 50040000 [size=128K]
> Capabilities: <access denied>
> Kernel driver in use: r8169
>
> 00:08.0 VGA compatible controller [0300]: Silicon Integrated Systems
> [SiS] 315PRO PCI/AGP VGA Display Adapter [1039:0325] (prog-if 00 [VGA
> controller])
> Subsystem: Device [3030:3030]
> Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop-
> ParErr- Stepping- SERR- FastB2B- DisINTx-
> Status: Cap+ 66MHz+ UDF- FastB2B- ParErr- DEVSEL=medium
> >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
> Latency: 71 (750ns min, 4000ns max)
> Interrupt: pin A routed to IRQ 38
> BIST result: 00
> Region 0: Memory at 40000000 (32-bit, prefetchable) [size=256M]
> Region 1: Memory at 50000000 (32-bit, non-prefetchable) [size=256K]
> Region 2: I/O ports at 4800 [size=128]
> Expansion ROM at 50060000 [size=64K]
> Capabilities: <access denied>
> Kernel driver in use: sisfb
>
> 00:0e.0 ISA bridge [0601]: Advanced Micro Devices [AMD] CS5536 [Geode
> companion] ISA [1022:2090] (rev 03)
> Subsystem: Advanced Micro Devices [AMD] CS5536 [Geode
> companion] ISA [1022:2090]
> Control: I/O+ Mem- BusMaster- SpecCycle- MemWINV- VGASnoop-
> ParErr- Stepping- SERR- FastB2B- DisINTx-
> Status: Cap- 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort-
> <TAbort- <MAbort- >SERR- <PERR- INTx-
> Region 0: I/O ports at 4cf0 [size=8]
> Region 1: I/O ports at 4400 [size=256]
> Region 2: I/O ports at 4c80 [size=64]
> Region 4: I/O ports at 4880 [size=128]
> Region 5: I/O ports at 4cc0 [size=32]
>
> 00:0e.2 IDE interface [0101]: Advanced Micro Devices [AMD] CS5536
> [Geode companion] IDE [1022:209a] (rev 01) (prog-if 80 [Master])
> Subsystem: Advanced Micro Devices [AMD] CS5536 [Geode
> companion] IDE [1022:209a]
> Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop-
> ParErr- Stepping- SERR- FastB2B- DisINTx-
> Status: Cap- 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort-
> <TAbort- <MAbort- >SERR- <PERR- INTx-
> Latency: 64 (16000ns max), Cache Line Size: 32 bytes
> Interrupt: pin A routed to IRQ 14
> Region 0: [virtual] Memory at 000001f0 (32-bit,
> non-prefetchable) [size=8]
> Region 1: [virtual] Memory at 000003f0 (type 3,
> non-prefetchable) [size=1]
> Region 2: [virtual] Memory at 00000170 (32-bit,
> non-prefetchable) [size=8]
> Region 3: [virtual] Memory at 00000370 (type 3,
> non-prefetchable) [size=1]
> Region 4: I/O ports at 4ce0 [size=16]
> Kernel driver in use: pata_amd
>
> 00:0e.3 Multimedia audio controller [0401]: Advanced Micro Devices
> [AMD] CS5536 [Geode companion] Audio [1022:2093] (rev 01)
> Subsystem: Advanced Micro Devices [AMD] CS5536 [Geode
> companion] Audio [1022:2093]
> Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop-
> ParErr- Stepping- SERR- FastB2B- DisINTx-
> Status: Cap- 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort-
> <TAbort- <MAbort- >SERR- <PERR- INTx-
> Latency: 0 (16000ns max), Cache Line Size: 32 bytes
> Interrupt: pin A routed to IRQ 9
> Region 0: I/O ports at 4c00 [size=128]
> Kernel driver in use: cs5535audio
>
> 00:0e.4 USB Controller [0c03]: Advanced Micro Devices [AMD] CS5536
> [Geode companion] OHC [1022:2094] (rev 02) (prog-if 10 [OHCI])
> Subsystem: Advanced Micro Devices [AMD] CS5536 [Geode
> companion] OHC [1022:2094]
> Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop-
> ParErr- Stepping- SERR- FastB2B- DisINTx-
> Status: Cap- 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort-
> <TAbort- <MAbort- >SERR- <PERR- INTx-
> Latency: 0 (16000ns max), Cache Line Size: 32 bytes
> Interrupt: pin A routed to IRQ 11
> Region 0: Memory at 50070000 (32-bit, non-prefetchable) [size=4K]
> Kernel driver in use: ohci_hcd
>
> 00:0e.5 USB Controller [0c03]: Advanced Micro Devices [AMD] CS5536
> [Geode companion] EHC [1022:2095] (rev 02) (prog-if 20 [EHCI])
> Subsystem: Advanced Micro Devices [AMD] CS5536 [Geode
> companion] EHC [1022:2095]
> Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop-
> ParErr- Stepping- SERR- FastB2B- DisINTx-
> Status: Cap- 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort-
> <TAbort- <MAbort- >SERR- <PERR- INTx-
> Latency: 0 (16000ns max), Cache Line Size: 32 bytes
> Interrupt: pin A routed to IRQ 11
> Region 0: Memory at 50071000 (32-bit, non-prefetchable) [size=4K]
> Kernel driver in use: ehci_hcd
>
>
> ** USB devices:
> Bus 001 Device 001: ID 1d6b:0002 Linux Foundation 2.0 root hub
> Bus 002 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub
> Bus 002 Device 002: ID 04d9:1702 Holtek Semiconductor, Inc.
> Bus 002 Device 003: ID 0458:003a KYE Systems Corp. (Mouse Systems)
> NetScroll+ Mini Traveler / Genius NetScroll 120
>
>
> -- System Information:
> Debian Release: wheezy/sid
> APT prefers unstable
> APT policy: (500, 'unstable')
> Architecture: mipsel (mips64)
>
> Kernel: Linux 2.6.37-1-loongson-2f
> Locale: LANG=en_US.UTF-8, LC_CTYPE=en_US.UTF-8 (charmap=UTF-8)
> Shell: /bin/sh linked to /bin/dash
>
> Versions of packages linux-image-2.6.37-1-loongson-2f depends on:
> ii debconf [debconf-2.0] 1.5.38 Debian configuration management sy
> ii linux-base 2.6.37-1 Linux image base package
> ii module-init-tools 3.12-1 tools for managing Linux kernel mo
>
> Versions of packages linux-image-2.6.37-1-loongson-2f recommends:
> ii firmware-linux-free 2.6.37-1 Binary firmware for various driver
>
> Versions of packages linux-image-2.6.37-1-loongson-2f suggests:
> pn linux-doc-2.6.37 <none> (no description available)
>
> Versions of packages linux-image-2.6.37-1-loongson-2f is related to:
> pn firmware-bnx2 <none> (no description available)
> pn firmware-bnx2x <none> (no description available)
> pn firmware-ipw2x00 <none> (no description available)
> pn firmware-ivtv <none> (no description available)
> pn firmware-iwlwifi <none> (no description available)
> ii firmware-linux 0.28 Binary firmware for various driver
> ii firmware-linux-nonfree 0.28 Binary firmware for various driver
> pn firmware-qlogic <none> (no description available)
> pn firmware-ralink <none> (no description available)
> pn xen-hypervisor <none> (no description available)
>
> -- debconf information:
> * linux-image-2.6.37-1-loongson-2f/postinst/ignoring-do-bootloader-2.6.37-1-loongson-2f:
> linux-image-2.6.37-1-loongson-2f/postinst/depmod-error-initrd-2.6.37-1-loongson-2f:
> false
> linux-image-2.6.37-1-loongson-2f/postinst/missing-firmware-2.6.37-1-loongson-2f:
> linux-image-2.6.37-1-loongson-2f/prerm/removing-running-kernel-2.6.37-1-loongson-2f:
> true
>
>
> Thanks,
>
> --
> Javier.
>
>
>
> --
> To UNSUBSCRIBE, email to debian-kernel-REQUEST@lists.debian.org
> with a subject of "unsubscribe". Trouble? Contact listmaster@lists.debian.org
> Archive: [🔎] AANLkTikuX2_GoG10Fk1eXCwwoZodjcgeaO2r+=Naq9bM@mail.gmail.com">http://lists.debian.org/[🔎] AANLkTikuX2_GoG10Fk1eXCwwoZodjcgeaO2r+=Naq9bM@mail.gmail.com
--
Martin Michlmayr
http://www.cyrius.com/
Reply to: