[Date Prev][Date Next] [Thread Prev][Thread Next] [Date Index] [Thread Index]

Bug#504138: marked as done (linux-image-2.6.26-1-686: Framebuffer goes blank after X start)



Your message dated Sun, 30 May 2010 14:44:13 +0200
with message-id <20100530124413.GD2398@galadriel.inutil.org>
and subject line Re: linux-image-2.6.26-1-686: Framebuffer goes blank after X start
has caused the Debian Bug report #504138,
regarding linux-image-2.6.26-1-686: Framebuffer goes blank after X start
to be marked as done.

This means that you claim that the problem has been dealt with.
If this is not the case it is now your responsibility to reopen the
Bug report if necessary, and/or fix the problem forthwith.

(NB: If you are a system administrator and have no idea what this
message is talking about, this may indicate a serious mail system
misconfiguration somewhere. Please contact owner@bugs.debian.org
immediately.)


-- 
504138: http://bugs.debian.org/cgi-bin/bugreport.cgi?bug=504138
Debian Bug Tracking System
Contact owner@bugs.debian.org with problems
--- Begin Message ---
Package: linux-image-2.6.26-1-686
Version: 2.6.26-9
Severity: normal

After starting X server all tty framebuffers go blank. Before X start,
framebuffer display boot process normally
though. It seems vesafb kernel module is not loaded at boot, resulting
in the blank framebuffers.
The problem does not appear in version 2.6.26.8.


-- Package-specific info:
** Version:
Linux version 2.6.26-1-686 (Debian 2.6.26-9) (waldi@debian.org) (gcc
version 4.1.3 20080623 (prerelease) (Debian 4.1.2-23)) #1 SMP Sat Oct
18 16:22:25 UTC 2008

** Command line:
root=/dev/sda5 ro quiet vga=792 splash acpi_sleep=s3_bios

** Not tainted

** Kernel log:
[   68.894667] PM: Writing back config space on device 0000:03:00.0 at
offset 1 (was 100102, writing 100106)
[   68.894667] firmware: requesting iwlwifi-3945-1.ucode
[   69.033278] Registered led device: iwl-phy0:radio
[   69.033278] Registered led device: iwl-phy0:assoc
[   69.033278] Registered led device: iwl-phy0:RX
[   69.033278] Registered led device: iwl-phy0:TX
[   71.193352] NET: Registered protocol family 10
[   71.193352] lo: Disabled Privacy Extensions
[   71.193352] ADDRCONF(NETDEV_UP): eth1: link is not ready
[   71.193352] ADDRCONF(NETDEV_UP): wlan0_rename: link is not ready
[   72.354378] CPU0 attaching NULL sched-domain.
[   72.354378] CPU1 attaching NULL sched-domain.
[   72.357935] CPU0 attaching sched-domain:
[   72.357944]  domain 0: span 0-1
[   72.357948]   groups: 0 1
[   72.357956]   domain 1: span 0-1
[   72.357960]    groups: 0-1
[   72.357966] CPU1 attaching sched-domain:
[   72.357970]  domain 0: span 0-1
[   72.357974]   groups: 1 0
[   72.357980]   domain 1: span 0-1
[   72.357984]    groups: 0-1
[  248.682451] CPU0 attaching NULL sched-domain.
[  248.682451] CPU1 attaching NULL sched-domain.
[  248.688228] CPU0 attaching sched-domain:
[  248.688234]  domain 0: span 0-1
[  248.688237]   groups: 0 1
[  248.688247] CPU1 attaching sched-domain:
[  248.688251]  domain 0: span 0-1
[  248.688256]   groups: 1 0
[  253.616093] wlan0_rename: Initial auth_alg=0
[  253.616100] wlan0_rename: authenticate with AP 00:10:c6:f2:4f:e5
[  253.618879] wlan0_rename: RX authentication from 00:10:c6:f2:4f:e5
(alg=0 transaction=2 status=0)
[  253.618885] wlan0_rename: authenticated
[  253.618888] wlan0_rename: associate with AP 00:10:c6:f2:4f:e5
[  253.623222] wlan0_rename: RX AssocResp from 00:10:c6:f2:4f:e5
(capab=0x411 status=0 aid=1)
[  253.623227] wlan0_rename: associated
[  253.623237] wlan0_rename: switched to short barker preamble
(BSSID=00:10:c6:f2:4f:e5)
[  253.630740] ADDRCONF(NETDEV_CHANGE): wlan0_rename: link becomes ready
[  269.011180] wlan0_rename: no IPv6 routers present
[  651.686769] CE: hpet increasing min_delta_ns to 15000 nsec
[ 3224.843319] CPU0 attaching NULL sched-domain.
[ 3224.843319] CPU1 attaching NULL sched-domain.
[ 3224.847343] CPU0 attaching sched-domain:
[ 3224.847352]  domain 0: span 0-1
[ 3224.847356]   groups: 0 1
[ 3224.847363]   domain 1: span 0-1
[ 3224.847367]    groups: 0-1
[ 3224.847373] CPU1 attaching sched-domain:
[ 3224.847377]  domain 0: span 0-1
[ 3224.847381]   groups: 1 0
[ 3224.847387]   domain 1: span 0-1
[ 3224.847391]    groups: 0-1
[ 3229.368885] wlan0_rename: No ProbeResp from current AP
00:10:c6:f2:4f:e5 - assume out of range
[ 3229.728578] CPU0 attaching NULL sched-domain.
[ 3229.728585] CPU1 attaching NULL sched-domain.
[ 3229.732521] CPU0 attaching sched-domain:
[ 3229.732521]  domain 0: span 0-1
[ 3229.732521]   groups: 0 1
[ 3229.732521] CPU1 attaching sched-domain:
[ 3229.732521]  domain 0: span 0-1
[ 3229.732521]   groups: 1 0
[ 3231.043710] CPU0 attaching NULL sched-domain.
[ 3231.043719] CPU1 attaching NULL sched-domain.
[ 3231.065746] CPU0 attaching sched-domain:
[ 3231.065746]  domain 0: span 0-1
[ 3231.065746]   groups: 0 1
[ 3231.065746]   domain 1: span 0-1
[ 3231.065746]    groups: 0-1
[ 3231.065746] CPU1 attaching sched-domain:
[ 3231.065746]  domain 0: span 0-1
[ 3231.065746]   groups: 1 0
[ 3231.065746]   domain 1: span 0-1
[ 3231.065746]    groups: 0-1
[ 3239.628956] ACPI: PCI interrupt for device 0000:03:00.0 disabled
[ 3239.630312] ACPI: PCI Interrupt 0000:03:00.0[A] -> GSI 17 (level,
low) -> IRQ 17
[ 3239.630486] PM: Writing back config space on device 0000:03:00.0 at
offset 1 (was 100102, writing 100106)
[ 3239.674448] Registered led device: iwl-phy0:radio
[ 3239.674448] Registered led device: iwl-phy0:assoc
[ 3239.674448] Registered led device: iwl-phy0:RX
[ 3239.674448] Registered led device: iwl-phy0:TX
[ 3239.675916] ADDRCONF(NETDEV_UP): wlan0_rename: link is not ready
[ 3242.389676] CPU0 attaching NULL sched-domain.
[ 3242.389684] CPU1 attaching NULL sched-domain.
[ 3242.393751] CPU0 attaching sched-domain:
[ 3242.393751]  domain 0: span 0-1
[ 3242.393751]   groups: 0 1
[ 3242.393751] CPU1 attaching sched-domain:
[ 3242.393751]  domain 0: span 0-1
[ 3242.393751]   groups: 1 0
[ 3341.151693] wlan0_rename: Initial auth_alg=0
[ 3341.151693] wlan0_rename: authenticate with AP 00:10:c6:f2:4f:e5
[ 3341.157272] wlan0_rename: RX authentication from 00:10:c6:f2:4f:e5
(alg=0 transaction=2 status=0)
[ 3341.157272] wlan0_rename: authenticated
[ 3341.157272] wlan0_rename: associate with AP 00:10:c6:f2:4f:e5
[ 3341.159379] wlan0_rename: RX AssocResp from 00:10:c6:f2:4f:e5
(capab=0x411 status=0 aid=1)
[ 3341.159379] wlan0_rename: associated
[ 3341.159379] wlan0_rename: switched to short barker preamble
(BSSID=00:10:c6:f2:4f:e5)
[ 3341.159379] ADDRCONF(NETDEV_CHANGE): wlan0_rename: link becomes ready
[ 3358.529184] wlan0_rename: no IPv6 routers present

** Loaded modules:
Module                  Size  Used by
ipv6                  235300  14
rfcomm                 28272  2
l2cap                  17248  5 rfcomm
bluetooth              44900  4 rfcomm,l2cap
vboxdrv                63648  0
uinput                  6592  1
ppdev                   6468  0
parport_pc             22500  0
lp                      8164  0
parport                30988  3 ppdev,parport_pc,lp
sbp2                   18572  0
loop                   12748  0
pcmcia                 29548  0
psmouse                32336  0
serio_raw               4740  0
snd_hda_intel         324248  1
yenta_socket           20620  1
rsrc_nonstatic          9504  1 yenta_socket
arc4                    1824  2
pcspkr                  2432  0
i2c_i801                7920  0
pcmcia_core            31892  3 pcmcia,yenta_socket,rsrc_nonstatic
rng_core                3940  0
iTCO_wdt                9508  0
i2c_core               19828  1 i2c_i801
battery                10180  0
video                  16400  0
ac                      4196  0
ecb                     2624  2
output                  2912  1 video
bay                     4160  0
crypto_blkcipher       15236  1 ecb
snd_pcm                62596  1 snd_hda_intel
snd_seq                41456  0
snd_timer              17800  2 snd_pcm,snd_seq
snd_seq_device          6380  1 snd_seq
iwl3945                78772  0
firmware_class          6816  2 pcmcia,iwl3945
snd                    45604  7
snd_hda_intel,snd_pcm,snd_seq,snd_timer,snd_seq_device
mac80211              139680  1 iwl3945
soundcore               6368  1 snd
button                  6064  0
snd_page_alloc          7816  2 snd_hda_intel,snd_pcm
cfg80211               21576  2 iwl3945,mac80211
intel_agp              22300  1
agpgart                28776  2 intel_agp
thinkpad_acpi          49632  0
led_class               3908  2 iwl3945,thinkpad_acpi
nvram                   7116  2 thinkpad_acpi
evdev                   8000  8
reiserfs              189920  2
sd_mod                 22200  4
ide_pci_generic         3908  0 [permanent]
ide_core               96168  1 ide_pci_generic
ata_piix               14180  3
ohci1394               24944  0
sdhci                  13060  0
ieee1394               75800  2 sbp2,ohci1394
mmc_core               39932  1 sdhci
ata_generic             4676  0
libata                140384  2 ata_piix,ata_generic
scsi_mod              129356  3 sbp2,sd_mod,libata
ehci_hcd               28428  0
uhci_hcd               18672  0
usbcore               118160  3 ehci_hcd,uhci_hcd
e1000e                 84612  0
dock                    8272  2 bay,libata
thermal                15228  0
processor              32576  3 thermal
fan                     4164  0
thermal_sys            10856  4 video,thermal,processor,fan

** PCI devices:
00:00.0 Host bridge [0600]: Intel Corporation Mobile 945GM/PM/GMS,
943/940GML and 945GT Express Memory Controller Hub [8086:27a0] (rev
03)
	Subsystem: Lenovo ThinkPad T60/R60 series [17aa:2017]
	Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR+ FastB2B- DisINTx-
	Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=fast >TAbort-
<TAbort- <MAbort+ >SERR- <PERR- INTx-
	Latency: 0
	Capabilities: <access denied>
	Kernel driver in use: agpgart-intel
	Kernel modules: intel-agp

00:02.0 VGA compatible controller [0300]: Intel Corporation Mobile
945GM/GMS, 943/940GML Express Integrated Graphics Controller
[8086:27a2] (rev 03) (prog-if 00 [VGA controller])
	Subsystem: Lenovo ThinkPad T60/R60 series [17aa:201a]
	Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B- DisINTx-
	Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=fast >TAbort-
<TAbort- <MAbort- >SERR- <PERR- INTx-
	Latency: 0
	Interrupt: pin A routed to IRQ 11
	Region 0: Memory at ee100000 (32-bit, non-prefetchable) [size=512K]
	Region 1: I/O ports at 1800 [size=8]
	Region 2: Memory at d0000000 (32-bit, prefetchable) [size=256M]
	Region 3: Memory at ee200000 (32-bit, non-prefetchable) [size=256K]
	Capabilities: <access denied>
	Kernel modules: intelfb

00:02.1 Display controller [0380]: Intel Corporation Mobile
945GM/GMS/GME, 943/940GML Express Integrated Graphics Controller
[8086:27a6] (rev 03)
	Subsystem: Lenovo ThinkPad T60/R60 series [17aa:201a]
	Control: I/O+ Mem+ BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B- DisINTx-
	Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=fast >TAbort-
<TAbort- <MAbort- >SERR- <PERR- INTx-
	Region 0: Memory at ee180000 (32-bit, non-prefetchable) [size=512K]
	Capabilities: <access denied>

00:1b.0 Audio device [0403]: Intel Corporation 82801G (ICH7 Family)
High Definition Audio Controller [8086:27d8] (rev 02)
	Subsystem: Lenovo ThinkPad T60/R60 series [17aa:2010]
	Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR+ FastB2B- DisINTx-
	Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort-
<TAbort- <MAbort- >SERR- <PERR- INTx-
	Latency: 0, Cache Line Size: 64 bytes
	Interrupt: pin B routed to IRQ 17
	Region 0: Memory at ee240000 (64-bit, non-prefetchable) [size=16K]
	Capabilities: <access denied>
	Kernel driver in use: HDA Intel
	Kernel modules: snd-hda-intel

00:1c.0 PCI bridge [0604]: Intel Corporation 82801G (ICH7 Family) PCI
Express Port 1 [8086:27d0] (rev 02) (prog-if 00 [Normal decode])
	Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR+ FastB2B- DisINTx+
	Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort-
<TAbort- <MAbort- >SERR- <PERR- INTx-
	Latency: 0, Cache Line Size: 64 bytes
	Bus: primary=00, secondary=02, subordinate=02, sec-latency=0
	I/O behind bridge: 00002000-00002fff
	Memory behind bridge: ee000000-ee0fffff
	Secondary status: 66MHz- FastB2B- ParErr- DEVSEL=fast >TAbort-
<TAbort- <MAbort- <SERR- <PERR-
	BridgeCtl: Parity- SERR- NoISA+ VGA- MAbort- >Reset- FastB2B-
		PriDiscTmr- SecDiscTmr- DiscTmrStat- DiscTmrSERREn-
	Capabilities: <access denied>
	Kernel driver in use: pcieport-driver
	Kernel modules: shpchp

00:1c.1 PCI bridge [0604]: Intel Corporation 82801G (ICH7 Family) PCI
Express Port 2 [8086:27d2] (rev 02) (prog-if 00 [Normal decode])
	Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR+ FastB2B- DisINTx+
	Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort-
<TAbort- <MAbort- >SERR- <PERR- INTx-
	Latency: 0, Cache Line Size: 64 bytes
	Bus: primary=00, secondary=03, subordinate=03, sec-latency=0
	I/O behind bridge: 00003000-00004fff
	Memory behind bridge: ec000000-edffffff
	Prefetchable memory behind bridge: 00000000e4000000-00000000e40fffff
	Secondary status: 66MHz- FastB2B- ParErr- DEVSEL=fast >TAbort-
<TAbort- <MAbort- <SERR- <PERR-
	BridgeCtl: Parity- SERR- NoISA+ VGA- MAbort- >Reset- FastB2B-
		PriDiscTmr- SecDiscTmr- DiscTmrStat- DiscTmrSERREn-
	Capabilities: <access denied>
	Kernel driver in use: pcieport-driver
	Kernel modules: shpchp

00:1c.2 PCI bridge [0604]: Intel Corporation 82801G (ICH7 Family) PCI
Express Port 3 [8086:27d4] (rev 02) (prog-if 00 [Normal decode])
	Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR+ FastB2B- DisINTx+
	Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort-
<TAbort- <MAbort- >SERR- <PERR- INTx-
	Latency: 0, Cache Line Size: 64 bytes
	Bus: primary=00, secondary=04, subordinate=0b, sec-latency=0
	I/O behind bridge: 00005000-00006fff
	Memory behind bridge: e8000000-e9ffffff
	Prefetchable memory behind bridge: 00000000e4100000-00000000e41fffff
	Secondary status: 66MHz- FastB2B- ParErr- DEVSEL=fast >TAbort-
<TAbort- <MAbort- <SERR- <PERR-
	BridgeCtl: Parity- SERR- NoISA+ VGA- MAbort- >Reset- FastB2B-
		PriDiscTmr- SecDiscTmr- DiscTmrStat- DiscTmrSERREn-
	Capabilities: <access denied>
	Kernel driver in use: pcieport-driver
	Kernel modules: shpchp

00:1c.3 PCI bridge [0604]: Intel Corporation 82801G (ICH7 Family) PCI
Express Port 4 [8086:27d6] (rev 02) (prog-if 00 [Normal decode])
	Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR+ FastB2B- DisINTx+
	Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort-
<TAbort- <MAbort- >SERR- <PERR- INTx-
	Latency: 0, Cache Line Size: 64 bytes
	Bus: primary=00, secondary=0c, subordinate=13, sec-latency=0
	I/O behind bridge: 00007000-00008fff
	Memory behind bridge: ea000000-ebffffff
	Prefetchable memory behind bridge: 00000000e4200000-00000000e42fffff
	Secondary status: 66MHz- FastB2B- ParErr- DEVSEL=fast >TAbort-
<TAbort- <MAbort- <SERR- <PERR-
	BridgeCtl: Parity- SERR- NoISA+ VGA- MAbort- >Reset- FastB2B-
		PriDiscTmr- SecDiscTmr- DiscTmrStat- DiscTmrSERREn-
	Capabilities: <access denied>
	Kernel driver in use: pcieport-driver
	Kernel modules: shpchp

00:1d.0 USB Controller [0c03]: Intel Corporation 82801G (ICH7 Family)
USB UHCI Controller #1 [8086:27c8] (rev 02) (prog-if 00 [UHCI])
	Subsystem: Lenovo ThinkPad T60/R60 series [17aa:200a]
	Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B- DisINTx-
	Status: Cap- 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR- INTx-
	Latency: 0
	Interrupt: pin A routed to IRQ 16
	Region 4: I/O ports at 1820 [size=32]
	Kernel driver in use: uhci_hcd
	Kernel modules: uhci-hcd

00:1d.1 USB Controller [0c03]: Intel Corporation 82801G (ICH7 Family)
USB UHCI Controller #2 [8086:27c9] (rev 02) (prog-if 00 [UHCI])
	Subsystem: Lenovo ThinkPad T60/R60 series [17aa:200a]
	Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B- DisINTx-
	Status: Cap- 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR- INTx-
	Latency: 0
	Interrupt: pin B routed to IRQ 17
	Region 4: I/O ports at 1840 [size=32]
	Kernel driver in use: uhci_hcd
	Kernel modules: uhci-hcd

00:1d.2 USB Controller [0c03]: Intel Corporation 82801G (ICH7 Family)
USB UHCI Controller #3 [8086:27ca] (rev 02) (prog-if 00 [UHCI])
	Subsystem: Lenovo ThinkPad T60/R60 series [17aa:200a]
	Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B- DisINTx-
	Status: Cap- 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR- INTx-
	Latency: 0
	Interrupt: pin C routed to IRQ 18
	Region 4: I/O ports at 1860 [size=32]
	Kernel driver in use: uhci_hcd
	Kernel modules: uhci-hcd

00:1d.3 USB Controller [0c03]: Intel Corporation 82801G (ICH7 Family)
USB UHCI Controller #4 [8086:27cb] (rev 02) (prog-if 00 [UHCI])
	Subsystem: Lenovo ThinkPad T60/R60 series [17aa:200a]
	Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B- DisINTx-
	Status: Cap- 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR- INTx-
	Latency: 0
	Interrupt: pin D routed to IRQ 19
	Region 4: I/O ports at 1880 [size=32]
	Kernel driver in use: uhci_hcd
	Kernel modules: uhci-hcd

00:1d.7 USB Controller [0c03]: Intel Corporation 82801G (ICH7 Family)
USB2 EHCI Controller [8086:27cc] (rev 02) (prog-if 20 [EHCI])
	Subsystem: Lenovo ThinkPad T60/R60 series [17aa:200b]
	Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR+ FastB2B- DisINTx-
	Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR- INTx-
	Latency: 0
	Interrupt: pin D routed to IRQ 19
	Region 0: Memory at ee444000 (32-bit, non-prefetchable) [size=1K]
	Capabilities: <access denied>
	Kernel driver in use: ehci_hcd
	Kernel modules: ehci-hcd

00:1e.0 PCI bridge [0604]: Intel Corporation 82801 Mobile PCI Bridge
[8086:2448] (rev e2) (prog-if 01 [Subtractive decode])
	Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B- DisINTx-
	Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort-
<TAbort- <MAbort- >SERR- <PERR- INTx-
	Latency: 0
	Bus: primary=00, secondary=15, subordinate=18, sec-latency=32
	I/O behind bridge: 00009000-0000cfff
	Memory behind bridge: e4300000-e7ffffff
	Prefetchable memory behind bridge: 00000000e0000000-00000000e3ffffff
	Secondary status: 66MHz- FastB2B+ ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort+ <SERR- <PERR-
	BridgeCtl: Parity- SERR- NoISA- VGA- MAbort- >Reset- FastB2B-
		PriDiscTmr- SecDiscTmr- DiscTmrStat- DiscTmrSERREn-
	Capabilities: <access denied>

00:1f.0 ISA bridge [0601]: Intel Corporation 82801GBM (ICH7-M) LPC
Interface Bridge [8086:27b9] (rev 02)
	Subsystem: Lenovo ThinkPad T60/R60 series [17aa:2009]
	Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B- DisINTx-
	Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR- INTx-
	Latency: 0
	Capabilities: <access denied>
	Kernel modules: intel-rng, iTCO_wdt

00:1f.2 IDE interface [0101]: Intel Corporation 82801GBM/GHM (ICH7
Family) SATA IDE Controller [8086:27c4] (rev 02) (prog-if 80 [Master])
	Subsystem: Lenovo Thinkpad T60 model 2007 [17aa:200e]
	Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B- DisINTx-
	Status: Cap+ 66MHz+ UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR- INTx+
	Latency: 0
	Interrupt: pin B routed to IRQ 16
	Region 0: I/O ports at 01f0 [size=8]
	Region 1: I/O ports at 03f4 [size=1]
	Region 2: I/O ports at 0170 [size=8]
	Region 3: I/O ports at 0374 [size=1]
	Region 4: I/O ports at 18b0 [size=16]
	Capabilities: <access denied>
	Kernel driver in use: ata_piix
	Kernel modules: ata_piix

00:1f.3 SMBus [0c05]: Intel Corporation 82801G (ICH7 Family) SMBus
Controller [8086:27da] (rev 02)
	Subsystem: Lenovo ThinkPad T60/R60 series [17aa:200f]
	Control: I/O+ Mem- BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR+ FastB2B- DisINTx-
	Status: Cap- 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR- INTx-
	Interrupt: pin A routed to IRQ 23
	Region 4: I/O ports at 18e0 [size=32]
	Kernel driver in use: i801_smbus
	Kernel modules: i2c-i801

02:00.0 Ethernet controller [0200]: Intel Corporation 82573L Gigabit
Ethernet Controller [8086:109a]
	Subsystem: Lenovo ThinkPad X60s [17aa:207e]
	Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR+ FastB2B- DisINTx+
	Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort-
<TAbort- <MAbort- >SERR- <PERR- INTx-
	Latency: 0, Cache Line Size: 64 bytes
	Interrupt: pin A routed to IRQ 218
	Region 0: Memory at ee000000 (32-bit, non-prefetchable) [size=128K]
	Region 2: I/O ports at 2000 [size=32]
	Capabilities: <access denied>
	Kernel driver in use: e1000e
	Kernel modules: e1000e

03:00.0 Network controller [0280]: Intel Corporation PRO/Wireless
3945ABG [Golan] Network Connection [8086:4227] (rev 02)
	Subsystem: Intel Corporation ThinkPad R60e/X60s [8086:1011]
	Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR+ FastB2B- DisINTx+
	Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort-
<TAbort- <MAbort- >SERR- <PERR- INTx-
	Latency: 0, Cache Line Size: 64 bytes
	Interrupt: pin A routed to IRQ 219
	Region 0: Memory at edf00000 (32-bit, non-prefetchable) [size=4K]
	Capabilities: <access denied>
	Kernel driver in use: iwl3945
	Kernel modules: iwl3945

15:00.0 CardBus bridge [0607]: Ricoh Co Ltd RL5c476 II [1180:0476] (rev b4)
	Subsystem: Lenovo Thinkpad X60s [17aa:201c]
	Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B- DisINTx-
	Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR- INTx-
	Latency: 168
	Interrupt: pin A routed to IRQ 16
	Region 0: Memory at e4300000 (32-bit, non-prefetchable) [size=4K]
	Bus: primary=15, secondary=16, subordinate=17, sec-latency=176
	Memory window 0: e0000000-e3fff000 (prefetchable)
	Memory window 1: 88000000-8bfff000
	I/O window 0: 00009000-000090ff
	I/O window 1: 00009400-000094ff
	BridgeCtl: Parity- SERR- ISA- VGA- MAbort- >Reset- 16bInt+ PostWrite+
	16-bit legacy interface ports at 0001
	Kernel driver in use: yenta_cardbus
	Kernel modules: yenta_socket

15:00.1 FireWire (IEEE 1394) [0c00]: Ricoh Co Ltd R5C552 IEEE 1394
Controller [1180:0552] (rev 09) (prog-if 10 [OHCI])
	Subsystem: Lenovo Thinkpad X60s [17aa:201e]
	Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B- DisINTx-
	Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR- INTx-
	Latency: 64 (500ns min, 1000ns max)
	Interrupt: pin B routed to IRQ 17
	Region 0: Memory at e4301000 (32-bit, non-prefetchable) [size=2K]
	Capabilities: <access denied>
	Kernel driver in use: ohci1394
	Kernel modules: ohci1394

15:00.2 SD Host controller [0805]: Ricoh Co Ltd R5C822
SD/SDIO/MMC/MS/MSPro Host Adapter [1180:0822] (rev 18)
	Subsystem: Lenovo Thinkpad X60s [17aa:201d]
	Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B- DisINTx-
	Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR- INTx-
	Latency: 64
	Interrupt: pin C routed to IRQ 18
	Region 0: Memory at e4301800 (32-bit, non-prefetchable) [size=256]
	Capabilities: <access denied>
	Kernel driver in use: sdhci
	Kernel modules: sdhci



-- System Information:
Debian Release: lenny/sid
  APT prefers unstable
  APT policy: (500, 'unstable'), (1, 'experimental')
Architecture: i386 (i686)

Kernel: Linux 2.6.26-1-686 (SMP w/2 CPU cores)
Locale: LANG=C, LC_CTYPE=C (charmap=ANSI_X3.4-1968)
Shell: /bin/sh linked to /bin/bash

Versions of packages linux-image-2.6.26-1-686 depends on:
ii  debconf [debconf-2.0]         1.5.24     Debian configuration management sy
ii  initramfs-tools [linux-initra 0.92l      tools for generating an initramfs
ii  module-init-tools             3.4-1      tools for managing Linux kernel mo

Versions of packages linux-image-2.6.26-1-686 recommends:
pn  libc6-i686                    <none>     (no description available)

Versions of packages linux-image-2.6.26-1-686 suggests:
ii  grub                          0.97-47    GRand Unified Bootloader (Legacy v
pn  linux-doc-2.6.26              <none>     (no description available)

-- debconf information:
  linux-image-2.6.26-1-686/preinst/abort-overwrite-2.6.26-1-686:
  shared/kernel-image/really-run-bootloader: true
  linux-image-2.6.26-1-686/postinst/bootloader-error-2.6.26-1-686:
  linux-image-2.6.26-1-686/postinst/depmod-error-initrd-2.6.26-1-686: false
  linux-image-2.6.26-1-686/prerm/removing-running-kernel-2.6.26-1-686: true
  linux-image-2.6.26-1-686/postinst/old-system-map-link-2.6.26-1-686: true
  linux-image-2.6.26-1-686/preinst/abort-install-2.6.26-1-686:
  linux-image-2.6.26-1-686/preinst/lilo-has-ramdisk:
  linux-image-2.6.26-1-686/preinst/bootloader-initrd-2.6.26-1-686: true
  linux-image-2.6.26-1-686/prerm/would-invalidate-boot-loader-2.6.26-1-686: true
  linux-image-2.6.26-1-686/preinst/elilo-initrd-2.6.26-1-686: true
  linux-image-2.6.26-1-686/postinst/kimage-is-a-directory:
  linux-image-2.6.26-1-686/postinst/old-dir-initrd-link-2.6.26-1-686: true
  linux-image-2.6.26-1-686/postinst/create-kimage-link-2.6.26-1-686: true
  linux-image-2.6.26-1-686/preinst/lilo-initrd-2.6.26-1-686: true
  linux-image-2.6.26-1-686/postinst/old-initrd-link-2.6.26-1-686: true
  linux-image-2.6.26-1-686/preinst/overwriting-modules-2.6.26-1-686: true
  linux-image-2.6.26-1-686/postinst/depmod-error-2.6.26-1-686: false
  linux-image-2.6.26-1-686/postinst/bootloader-test-error-2.6.26-1-686:
  linux-image-2.6.26-1-686/preinst/failed-to-move-modules-2.6.26-1-686:
  linux-image-2.6.26-1-686/preinst/initrd-2.6.26-1-686:



--- End Message ---
--- Begin Message ---
Version: 2.6.32-1

On Fri, Oct 31, 2008 at 11:20:35PM +0100, Apelete Seketeli wrote:
> Package: linux-image-2.6.26-1-686
> Version: 2.6.26-9
> Severity: normal
> 
> After starting X server all tty framebuffers go blank. Before X start,
> framebuffer display boot process normally
> though. It seems vesafb kernel module is not loaded at boot, resulting
> in the blank framebuffers.
> The problem does not appear in version 2.6.26.8.

In Squeeze the handling of the ttys is done through the Intel KMS code,
closing the bug.

If there are remainign problems with the current 2.6.32 kernels, please
file a new bug.

Cheers,
        Moritz


--- End Message ---

Reply to: