--- Begin Message ---
- To: Debian Bug Tracking System <submit@bugs.debian.org>
- Subject: BUG: unable to handle kernel NULL pointer dereference at virtual address 0000001c
- From: Miernik <public@public.miernik.name>
- Date: Fri, 01 Jun 2007 19:42:19 +0200
- Message-id: <20070601174219.2275.14850.reportbug@debian107>
Package: linux-image-2.6.21-1-686
Version: 2.6.21-4
Severity: normal
When I do "statserial /dev/ttyUSB2" this happens (I think the included
Kernel log provides enough data).
/dev/ttyUSB2 is on a Huawei E618 PCMCIA UMTS/GPRS card.
Here is what ATI says about the card:
Manufacturer: HUAWEI TECHNOLOGIES CO., LTD.
Model: 183
Revision: I:12.11.01B
I ommited the IMEI.
-- Package-specific info:
** Version: Linux version 2.6.21-1-686 (Debian 2.6.21-4) (waldi@debian.org) (gcc version 4.1.3 20070518 (prerelease) (Debian 4.1.2-8)) #1 SMP Sat May 26 16:14:59 UTC 2007
** Not tainted
** Kernel log:
pccard: CardBus card inserted into slot 0
pccard: CardBus card inserted into slot 1
[1487] nozomi_card_init(): Init, cards_found: 1
[1373] nozomi_get_card_type(): Card type is: 2048
PCI: Enabling device 0000:02:00.0 (0000 -> 0002)
ACPI: PCI Interrupt 0000:02:00.0[A] -> Link [LNKC] -> GSI 11 (level, low) -> IRQ 11
Nozomi driver nozomi_tty<6>[836] nozomi_read_config_table(): Version of card: 3
Initializing Nozomi driver 2.1 (build date: Jun 1 2007 19:26:41)
[828] nozomi_read_config_table(): Initialization OK!
cs: IO port probe 0x100-0x3af: clean.
cs: IO port probe 0x3e0-0x4ff: excluding 0x4d0-0x4d7
cs: IO port probe 0x820-0x8ff: clean.
cs: IO port probe 0xc00-0xcf7: clean.
cs: IO port probe 0xa00-0xaff: clean.
ohci_hcd: 2006 August 04 USB 1.1 'Open' Host Controller (OHCI) Driver
PCI: Enabling device 0000:06:00.0 (0000 -> 0002)
ACPI: PCI Interrupt 0000:06:00.0[A] -> Link [LNKC] -> GSI 11 (level, low) -> IRQ 11
PCI: Setting latency timer of device 0000:06:00.0 to 64
ohci_hcd 0000:06:00.0: OHCI Host Controller
ohci_hcd 0000:06:00.0: new USB bus registered, assigned bus number 2
ohci_hcd 0000:06:00.0: irq 11, io mem 0x1c000000
cs: IO port probe 0x100-0x3af: clean.
cs: IO port probe 0x3e0-0x4ff: excluding 0x4d0-0x4d7
cs: IO port probe 0x820-0x8ff: clean.
cs: IO port probe 0xc00-0xcf7: clean.
cs: IO port probe 0xa00-0xaff: clean.
usb usb2: configuration #1 chosen from 1 choice
hub 2-0:1.0: USB hub found
hub 2-0:1.0: 1 port detected
PCI: Enabling device 0000:06:00.1 (0000 -> 0002)
ACPI: PCI Interrupt 0000:06:00.1[B] -> Link [LNKC] -> GSI 11 (level, low) -> IRQ 11
PCI: Setting latency timer of device 0000:06:00.1 to 64
ohci_hcd 0000:06:00.1: OHCI Host Controller
ohci_hcd 0000:06:00.1: new USB bus registered, assigned bus number 3
ohci_hcd 0000:06:00.1: irq 11, io mem 0x1c001000
usb usb3: configuration #1 chosen from 1 choice
hub 3-0:1.0: USB hub found
hub 3-0:1.0: 1 port detected
usb 2-1: new full speed USB device using ohci_hcd and address 2
usb 2-1: configuration #1 chosen from 1 choice
usbcore: registered new interface driver usbserial
drivers/usb/serial/usb-serial.c: USB Serial support registered for generic
usbcore: registered new interface driver usbserial_generic
drivers/usb/serial/usb-serial.c: USB Serial Driver core
drivers/usb/serial/usb-serial.c: USB Serial support registered for pl2303
pl2303 2-1:1.0: pl2303 converter detected
usb 2-1: pl2303 converter now attached to ttyUSB0
pl2303 2-1:1.1: pl2303 converter detected
usb 2-1: pl2303 converter now attached to ttyUSB1
pl2303 2-1:1.2: pl2303 converter detected
usb 2-1: pl2303 converter now attached to ttyUSB2
usbcore: registered new interface driver pl2303
drivers/usb/serial/pl2303.c: Prolific PL2303 USB to serial adaptor driver
drivers/usb/serial/usb-serial.c: USB Serial support registered for GSM modem (1-port)
usbcore: registered new interface driver option
drivers/usb/serial/option.c: USB Driver for GSM modems: v0.7.1
EXT3 FS on hda1, internal journal
loop: loaded (max 8 devices)
device-mapper: ioctl: 4.11.0-ioctl (2006-10-12) initialised: dm-devel@redhat.com
eth0: link up, 10Mbps, half-duplex, lpa 0x0000
NET: Registered protocol family 10
lo: Disabled Privacy Extensions
eth0: no IPv6 routers present
BUG: unable to handle kernel NULL pointer dereference at virtual address 0000001c
printing eip:
c8991984
*pde = 00000000
Oops: 0002 [#1]
SMP
Modules linked in: ext2 ipv6 dm_crypt dm_snapshot dm_mirror dm_mod loop option pl2303 usbserial ohci_hcd nozomi pcmcia firmware_class psmouse serio_raw rtc i2c_piix4 yenta_socket rsrc_nonstatic pcspkr pcmcia_core i2c_core shpchp pci_hotplug intel_agp agpgart sd_mod evdev ext3 jbd mbcache usb_storage ide_disk 8139too generic 8139cp mii uhci_hcd usbcore piix ide_core ata_generic libata scsi_mod thermal processor fan
CPU: 0
EIP: 0060:[<c8991984>] Not tainted VLI
EFLAGS: 00210246 (2.6.21-1-686 #1)
EIP is at pl2303_open+0x896/0x8f5 [pl2303]
eax: 00000000 ebx: 00000000 ecx: 00200246 edx: c7257000
esi: c13fc960 edi: c1395600 ebp: c773bda0 esp: c503be38
ds: 007b es: 007b fs: 00d8 gs: 0033 ss: 0068
Process statserial (pid: 2233, ti=c503a000 task=c7a0d070 task.ti=c503a000)
Stack: 00000040 00000009 00000000 00000000 00000000 00000064 00000003 00200286
00000000 c50cd000 c13e8800 00200286 c020f7a1 00000000 c0210406 c0165c68
00000901 00000000 c503bec8 c1395600 c13fc960 c50cd000 ffffffed c89c1f6d
Call Trace:
[<c020f7a1>] tty_ldisc_enable+0x27/0x29
[<c0210406>] init_dev+0x399/0x4a9
[<c0165c68>] get_unused_fd+0x4a/0xaa
[<c89c1f6d>] serial_open+0xcb/0x11c [usbserial]
[<c0212add>] tty_open+0x16c/0x2c3
[<c01697b8>] chrdev_open+0x120/0x13b
[<c0169698>] chrdev_open+0x0/0x13b
[<c0165d8b>] __dentry_open+0xc3/0x17a
[<c0165ebc>] nameidata_to_filp+0x24/0x33
[<c0165efd>] do_filp_open+0x32/0x39
[<c0165c68>] get_unused_fd+0x4a/0xaa
[<c0165f46>] do_sys_open+0x42/0xc3
[<c0166000>] sys_open+0x1c/0x1e
[<c0103d8c>] syscall_call+0x7/0xb
[<c0290000>] __find_acq_core+0x2ce/0x30e
=======================
Code: 6e 83 3d c0 4b 99 c8 00 74 1c c7 44 24 08 54 23 99 c8 c7 44 24 04 70 23 99 c8 c7 04 24 97 28 99 c8 e8 16 0c 79 f7 8b 47 24 8b 16 <89> 50 1c 8b 47 24 ba d0 00 00 00 e8 20 72 ea ff 89 c3 31 c0 85
EIP: [<c8991984>] pl2303_open+0x896/0x8f5 [pl2303] SS:ESP 0068:c503be38
** Loaded modules:
Module Size Used by
ext2 60168 1
ipv6 236320 12
dm_crypt 12808 0
dm_snapshot 16420 0
dm_mirror 20116 0
dm_mod 52556 3 dm_crypt,dm_snapshot,dm_mirror
loop 15880 0
option 9440 0
pl2303 19396 1
usbserial 31528 4 option,pl2303
ohci_hcd 19684 0
nozomi 18608 0
pcmcia 35276 0
firmware_class 9408 1 pcmcia
psmouse 34952 0
serio_raw 6564 0
rtc 12760 0
i2c_piix4 8556 0
yenta_socket 24876 4
rsrc_nonstatic 11968 1 yenta_socket
pcspkr 3136 0
pcmcia_core 36884 3 pcmcia,yenta_socket,rsrc_nonstatic
i2c_core 20480 1 i2c_piix4
shpchp 30996 0
pci_hotplug 29088 1 shpchp
intel_agp 23004 1
agpgart 32168 1 intel_agp
sd_mod 19904 2
evdev 9216 0
ext3 120904 1
jbd 55208 1 ext3
mbcache 8164 2 ext2,ext3
usb_storage 76384 1
ide_disk 15648 2
8139too 25536 0
generic 4804 0 [permanent]
8139cp 22336 0
mii 5280 2 8139too,8139cp
uhci_hcd 22608 0
usbcore 123304 7 option,pl2303,usbserial,ohci_hcd,usb_storage,uhci_hcd
piix 9508 0 [permanent]
ide_core 115016 4 usb_storage,ide_disk,generic,piix
ata_generic 8100 0
libata 109172 1 ata_generic
scsi_mod 133740 3 sd_mod,usb_storage,libata
thermal 14120 0
processor 30888 1 thermal
fan 4868 0
** PCI devices:
00:00.0 Host bridge [0600]: Intel Corporation 440BX/ZX/DX - 82443BX/ZX/DX Host bridge [8086:7190] (rev 03)
Subsystem: ASUSTeK Computer Inc. Unknown device [1043:8024]
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR+ FastB2B-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort+ >SERR- <PERR-
Latency: 64
Region 0: Memory at e4000000 (32-bit, prefetchable) [size=64M]
Capabilities: [a0] AGP version 1.0
Status: RQ=32 Iso- ArqSz=0 Cal=0 SBA+ ITACoh- GART64- HTrans- 64bit- FW- AGP3- Rate=x1,x2
Command: RQ=1 ArqSz=0 Cal=0 SBA- AGP- GART64- 64bit- FW- Rate=<none>
00:01.0 PCI bridge [0604]: Intel Corporation 440BX/ZX/DX - 82443BX/ZX/DX AGP bridge [8086:7191] (rev 03) (prog-if 00 [Normal decode])
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV+ VGASnoop- ParErr- Stepping- SERR+ FastB2B-
Status: Cap- 66MHz+ UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
Latency: 64
Bus: primary=00, secondary=01, subordinate=01, sec-latency=64
Secondary status: 66MHz+ FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort+ <SERR- <PERR-
BridgeCtl: Parity- SERR- NoISA- VGA- MAbort- >Reset- FastB2B+
00:04.0 ISA bridge [0601]: Intel Corporation 82371AB/EB/MB PIIX4 ISA [8086:7110] (rev 02)
Control: I/O+ Mem+ BusMaster+ SpecCycle+ MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
Status: Cap- 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
Latency: 0
00:04.1 IDE interface [0101]: Intel Corporation 82371AB/EB/MB PIIX4 IDE [8086:7111] (rev 01) (prog-if 80 [Master])
Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
Status: Cap- 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
Latency: 32
Region 0: [virtual] Memory at 000001f0 (32-bit, non-prefetchable) [disabled] [size=8]
Region 1: [virtual] Memory at 000003f0 (type 3, non-prefetchable) [disabled] [size=1]
Region 2: [virtual] Memory at 00000170 (32-bit, non-prefetchable) [disabled] [size=8]
Region 3: [virtual] Memory at 00000370 (type 3, non-prefetchable) [disabled] [size=1]
Region 4: I/O ports at d800 [size=16]
00:04.2 USB Controller [0c03]: Intel Corporation 82371AB/EB/MB PIIX4 USB [8086:7112] (rev 01) (prog-if 00 [UHCI])
Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
Status: Cap- 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
Latency: 32
Interrupt: pin D routed to IRQ 7
Region 4: I/O ports at d400 [size=32]
00:04.3 Bridge [0680]: Intel Corporation 82371AB/EB/MB PIIX4 ACPI [8086:7113] (rev 02)
Control: I/O+ Mem+ BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
Status: Cap- 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
Interrupt: pin ? routed to IRQ 9
00:0a.0 CardBus bridge [0607]: Ricoh Co Ltd RL5c475 [1180:0475] (rev 81)
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
Latency: 168
Interrupt: pin A routed to IRQ 11
Region 0: Memory at 20020000 (32-bit, non-prefetchable) [size=4K]
Bus: primary=00, secondary=02, subordinate=05, sec-latency=176
Memory window 0: 10000000-13fff000 (prefetchable)
Memory window 1: 14000000-17fff000
I/O window 0: 00001000-000010ff
I/O window 1: 00001400-000014ff
BridgeCtl: Parity- SERR- ISA- VGA- MAbort- >Reset- 16bInt- PostWrite+
16-bit legacy interface ports at 0001
00:0c.0 VGA compatible controller [0300]: Number 9 Computer Company Revolution 4 [105d:5348] (rev 02) (prog-if 00 [VGA])
Subsystem: Number 9 Computer Company Unknown device [105d:0017]
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
Status: Cap+ 66MHz+ UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
Latency: 0
Interrupt: pin A routed to IRQ 11
Region 0: Memory at e2000000 (32-bit, prefetchable) [size=32M]
Region 1: Memory at e0000000 (32-bit, prefetchable) [size=32M]
Region 2: Memory at df000000 (32-bit, non-prefetchable) [size=4K]
Region 4: Memory at de800000 (32-bit, non-prefetchable) [size=64K]
Region 5: I/O ports at d000 [size=256]
[virtual] Expansion ROM at 20000000 [disabled] [size=64K]
Capabilities: [80] AGP version 1.0
Status: RQ=16 Iso- ArqSz=0 Cal=0 SBA- ITACoh- GART64- HTrans- 64bit- FW- AGP3- Rate=x1,x2
Command: RQ=1 ArqSz=0 Cal=0 SBA- AGP- GART64- 64bit- FW- Rate=<none>
Capabilities: [90] Power Management version 1
Flags: PMEClk- DSI+ D1- D2- AuxCurrent=0mA PME(D0-,D1-,D2-,D3hot-,D3cold-)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-
00:0d.0 Ethernet controller [0200]: Realtek Semiconductor Co., Ltd. RTL-8139/8139C/8139C+ [10ec:8139] (rev 10)
Subsystem: OVISLINK Corp. LFE-8139ATX [149c:139a]
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
Latency: 32 (8000ns min, 16000ns max)
Interrupt: pin A routed to IRQ 7
Region 0: I/O ports at b800 [size=256]
Region 1: Memory at de000000 (32-bit, non-prefetchable) [size=256]
[virtual] Expansion ROM at 20010000 [disabled] [size=64K]
Capabilities: [50] Power Management version 2
Flags: PMEClk- DSI- D1+ D2+ AuxCurrent=0mA PME(D0-,D1+,D2+,D3hot+,D3cold-)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-
00:0e.0 CardBus bridge [0607]: Ricoh Co Ltd RL5c475 [1180:0475] (rev 81)
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
Latency: 168
Interrupt: pin A routed to IRQ 11
Region 0: Memory at 20021000 (32-bit, non-prefetchable) [size=4K]
Bus: primary=00, secondary=06, subordinate=09, sec-latency=176
Memory window 0: 18000000-1bfff000 (prefetchable)
Memory window 1: 1c000000-1ffff000
I/O window 0: 00001800-000018ff
I/O window 1: 00001c00-00001cff
BridgeCtl: Parity- SERR- ISA- VGA- MAbort- >Reset- 16bInt- PostWrite+
16-bit legacy interface ports at 0001
02:00.0 Network controller [0280]: Option N.V. Qualcomm MSM6275 UMTS chip [1931:000c]
Control: I/O- Mem+ BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
Status: Cap- 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
Interrupt: pin A routed to IRQ 11
Region 0: Memory at 14000000 (32-bit, non-prefetchable) [size=2K]
06:00.0 USB Controller [0c03]: NEC Corporation USB [1033:0035] (rev 43) (prog-if 10 [OHCI])
Subsystem: PSITech Unknown device [12d1:0035]
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
Latency: 64 (250ns min, 10500ns max)
Interrupt: pin A routed to IRQ 11
Region 0: Memory at 1c000000 (32-bit, non-prefetchable) [size=4K]
Capabilities: [40] Power Management version 2
Flags: PMEClk- DSI- D1+ D2+ AuxCurrent=0mA PME(D0+,D1+,D2+,D3hot+,D3cold-)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-
06:00.1 USB Controller [0c03]: NEC Corporation USB [1033:0035] (rev 43) (prog-if 10 [OHCI])
Subsystem: PSITech Unknown device [12d1:0035]
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
Latency: 64 (250ns min, 10500ns max)
Interrupt: pin B routed to IRQ 11
Region 0: Memory at 1c001000 (32-bit, non-prefetchable) [size=4K]
Capabilities: [40] Power Management version 2
Flags: PMEClk- DSI- D1+ D2+ AuxCurrent=0mA PME(D0+,D1+,D2+,D3hot+,D3cold-)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-
-- System Information:
Debian Release: lenny/sid
APT prefers unstable
APT policy: (500, 'unstable'), (500, 'testing'), (500, 'stable'), (1, 'experimental')
Architecture: i386 (i686)
Kernel: Linux 2.6.21-1-686 (SMP w/1 CPU core)
Locale: LANG=en_US.UTF-8, LC_CTYPE=en_US.UTF-8 (charmap=locale: Cannot set LC_CTYPE to default locale: No such file or directory
locale: Cannot set LC_MESSAGES to default locale: No such file or directory
locale: Cannot set LC_ALL to default locale: No such file or directory
ANSI_X3.4-1968)
Shell: /bin/sh linked to /bin/bash
Versions of packages linux-image-2.6.21-1-686 depends on:
ii initramfs-tools [linux-initr 0.88 tools for generating an initramfs
ii module-init-tools 3.3-pre11-1 tools for managing Linux kernel mo
Versions of packages linux-image-2.6.21-1-686 recommends:
ii libc6-i686 2.5-9+b1 GNU C Library: Shared libraries [i
-- debconf information:
perl: warning: Setting locale failed.
perl: warning: Please check that your locale settings:
LANGUAGE = (unset),
LC_ALL = (unset),
LANG = "en_US.UTF-8"
are supported and installed on your system.
perl: warning: Falling back to the standard locale ("C").
locale: Cannot set LC_CTYPE to default locale: No such file or directory
locale: Cannot set LC_MESSAGES to default locale: No such file or directory
locale: Cannot set LC_ALL to default locale: No such file or directory
shared/kernel-image/really-run-bootloader: true
linux-image-2.6.21-1-686/postinst/kimage-is-a-directory:
linux-image-2.6.21-1-686/prerm/removing-running-kernel-2.6.21-1-686: true
linux-image-2.6.21-1-686/preinst/lilo-initrd-2.6.21-1-686: true
linux-image-2.6.21-1-686/preinst/elilo-initrd-2.6.21-1-686: true
linux-image-2.6.21-1-686/postinst/depmod-error-2.6.21-1-686: false
linux-image-2.6.21-1-686/postinst/old-initrd-link-2.6.21-1-686: true
linux-image-2.6.21-1-686/preinst/lilo-has-ramdisk:
linux-image-2.6.21-1-686/preinst/abort-overwrite-2.6.21-1-686:
linux-image-2.6.21-1-686/postinst/bootloader-error-2.6.21-1-686:
linux-image-2.6.21-1-686/preinst/bootloader-initrd-2.6.21-1-686: true
linux-image-2.6.21-1-686/postinst/old-dir-initrd-link-2.6.21-1-686: true
linux-image-2.6.21-1-686/postinst/bootloader-test-error-2.6.21-1-686:
* linux-image-2.6.21-1-686/preinst/already-running-this-2.6.21-1-686:
linux-image-2.6.21-1-686/prerm/would-invalidate-boot-loader-2.6.21-1-686: true
linux-image-2.6.21-1-686/preinst/abort-install-2.6.21-1-686:
linux-image-2.6.21-1-686/postinst/depmod-error-initrd-2.6.21-1-686: false
linux-image-2.6.21-1-686/postinst/old-system-map-link-2.6.21-1-686: true
linux-image-2.6.21-1-686/preinst/failed-to-move-modules-2.6.21-1-686:
linux-image-2.6.21-1-686/preinst/initrd-2.6.21-1-686:
linux-image-2.6.21-1-686/postinst/create-kimage-link-2.6.21-1-686: true
linux-image-2.6.21-1-686/preinst/overwriting-modules-2.6.21-1-686: true
--- End Message ---