--- Begin Message ---
- To: Debian Bug Tracking System <submit@bugs.debian.org>
- Subject: linux-image-2.6.22-4-686: sata_via produces `exception Emask 0x0 SAct 0x0...' when mounting/umounting an IDE drive
- From: Dmitry Maksyoma <ledestin@amur.ru>
- Date: Sun, 16 Mar 2008 04:47:10 +1300
- Message-id: <20080315154710.19397.48937.reportbug@p42.f7.n5042.z2.fidonet.org>
Package: linux-image-2.6.22-4-686
Version: 2.6.22-6~bpo40+2
Severity: normal
I have a `RAID bus controller [0104]: VIA Technologies, Inc. VT6421 IDE RAID
Controller [1106:3249] (rev 50)' with one IDE controller onboard.
When I try to mount/umount a partition on an IDE drive (I tried one IBM and
one Seagate), the following appears in kern.log (more of output is included
by reportbug):
ata7.00: exception Emask 0x0 SAct 0x0 SErr 0x0 action 0x2
ata7.00: (BMDMA stat 0x4)
ata7.00: cmd ca/00:02:41:00:00/00:00:00:00:00/e0 tag 0 cdb 0x0 data 1024 out
res 51/84:00:42:00:00/00:00:00:00:00/e0 Emask 0x10 (ATA bus error)
ata7: soft resetting port
ata7.00: configured for UDMA/100
ata7: EH complete
Now, it could be just controller or hard drive failure, but I did the following tests:
1. An IDE DVD drive connected to the same controller works OK.
2. The same IDE drive connected to the same controller works OK in Windows
XP.
My kernel is tainted by nvidia driver, however, before reproducing the errors
I did `rmmod nvidia', so it shouldn't have interfered.
Here's sata_via initalisation:
sata_via 0000:05:01.0: version 2.2
ACPI: PCI Interrupt 0000:05:01.0[A] -> GSI 19 (level, low) -> IRQ 18
sata_via 0000:05:01.0: routed to hard irq line 11
scsi4 : sata_via
scsi5 : sata_via
scsi6 : sata_via
ata5: SATA max UDMA/133 cmd 0x0001d000 ctl 0x0001d00a bmdma 0x0001d400 irq 18
ata6: SATA max UDMA/133 cmd 0x0001d100 ctl 0x0001d10a bmdma 0x0001d408 irq 18
ata7: PATA max UDMA/133 cmd 0x0001d200 ctl 0x0001d20a bmdma 0x0001d410 irq 18
ata5: SATA link down (SStatus 0 SControl 310)
ata6: SATA link down (SStatus 0 SControl 310)
ata7.00: ATA-5: IC35L040AVER07-0, ER4OA45A, max UDMA/100
ata7.00: 80418240 sectors, multi 16: LBA
ata7.00: configured for UDMA/100
scsi 6:0:0:0: Direct-Access ATA IC35L040AVER07-0 ER4O PQ: 0 ANSI: 5
sd 6:0:0:0: [sdb] 80418240 512-byte hardware sectors (41174 MB)
sd 6:0:0:0: [sdb] Write Protect is off
sd 6:0:0:0: [sdb] Mode Sense: 00 3a 00 00
sd 6:0:0:0: [sdb] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
sd 6:0:0:0: [sdb] 80418240 512-byte hardware sectors (41174 MB)
sd 6:0:0:0: [sdb] Write Protect is off
sd 6:0:0:0: [sdb] Mode Sense: 00 3a 00 00
sd 6:0:0:0: [sdb] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
sdb: sdb1 sdb2 < sdb5 >
sd 6:0:0:0: [sdb] Attached SCSI disk
sd 6:0:0:0: Attached scsi generic sg1 type 0
-- Package-specific info:
** Version:
Linux version 2.6.22-4-686 (Debian 2.6.22-6~bpo40+2) (nobse@debian.org) (gcc version 4.1.2 20061115 (prerelease) (Debian 4.1.1-21)) #1 SMP Tue Feb 12 16:29:32 UTC 2008
** Tainted: P (1)
** Kernel log:
ata7.00: exception Emask 0x0 SAct 0x0 SErr 0x0 action 0x2
ata7.00: (BMDMA stat 0x4)
ata7.00: cmd ca/00:02:41:00:00/00:00:00:00:00/e0 tag 0 cdb 0x0 data 1024 out
res 51/84:00:42:00:00/00:00:00:00:00/e0 Emask 0x10 (ATA bus error)
ata7: soft resetting port
ata7.00: configured for UDMA/66
ata7: EH complete
ata7.00: exception Emask 0x0 SAct 0x0 SErr 0x0 action 0x2
ata7.00: (BMDMA stat 0x4)
ata7.00: cmd ca/00:02:41:00:00/00:00:00:00:00/e0 tag 0 cdb 0x0 data 1024 out
res 51/84:00:42:00:00/00:00:00:00:00/e0 Emask 0x10 (ATA bus error)
ata7: soft resetting port
ata7.00: configured for UDMA/66
sd 6:0:0:0: [sdb] Result: hostbyte=DID_OK driverbyte=DRIVER_SENSE,SUGGEST_OK
sd 6:0:0:0: [sdb] Sense Key : Aborted Command [current] [descriptor]
Descriptor sense data with sense descriptors (in hex):
72 0b 47 00 00 00 00 0c 00 0a 80 00 00 00 00 00
00 00 00 42
sd 6:0:0:0: [sdb] Add. Sense: Scsi parity error
end_request: I/O error, dev sdb, sector 65
Buffer I/O error on device sdb1, logical block 1
lost page write due to I/O error on sdb1
EXT3 FS on sdb1, <6>ata7: EH complete
sd 6:0:0:0: [sdb] 80418240 512-byte hardware sectors (41174 MB)
sd 6:0:0:0: [sdb] Write Protect is off
sd 6:0:0:0: [sdb] Mode Sense: 00 3a 00 00
sd 6:0:0:0: [sdb] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
sd 6:0:0:0: [sdb] 80418240 512-byte hardware sectors (41174 MB)
sd 6:0:0:0: [sdb] Write Protect is off
sd 6:0:0:0: [sdb] Mode Sense: 00 3a 00 00
sd 6:0:0:0: [sdb] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
internal journal
EXT3-fs: mounted filesystem with ordered data mode.
ata7.00: exception Emask 0x0 SAct 0x0 SErr 0x0 action 0x2
ata7.00: (BMDMA stat 0x4)
ata7.00: cmd ca/00:02:41:00:00/00:00:00:00:00/e0 tag 0 cdb 0x0 data 1024 out
res 51/84:00:42:00:00/00:00:00:00:00/e0 Emask 0x10 (ATA bus error)
ata7: soft resetting port
ata7.00: configured for UDMA/66
ata7: EH complete
ata7.00: limiting speed to UDMA/33:PIO4
ata7.00: exception Emask 0x0 SAct 0x0 SErr 0x0 action 0x2
ata7.00: (BMDMA stat 0x4)
ata7.00: cmd ca/00:02:41:00:00/00:00:00:00:00/e0 tag 0 cdb 0x0 data 1024 out
res 51/84:00:42:00:00/00:00:00:00:00/e0 Emask 0x10 (ATA bus error)
ata7: soft resetting port
ata7.00: configured for UDMA/33
ata7: EH complete
ata7.00: exception Emask 0x0 SAct 0x0 SErr 0x0 action 0x2
ata7.00: (BMDMA stat 0x4)
ata7.00: cmd ca/00:02:41:00:00/00:00:00:00:00/e0 tag 0 cdb 0x0 data 1024 out
res 51/84:00:42:00:00/00:00:00:00:00/e0 Emask 0x10 (ATA bus error)
ata7: soft resetting port
ata7.00: configured for UDMA/33
ata7: EH complete
ata7.00: exception Emask 0x0 SAct 0x0 SErr 0x0 action 0x2
ata7.00: (BMDMA stat 0x4)
ata7.00: cmd ca/00:02:41:00:00/00:00:00:00:00/e0 tag 0 cdb 0x0 data 1024 out
res 51/84:00:42:00:00/00:00:00:00:00/e0 Emask 0x10 (ATA bus error)
ata7: soft resetting port
ata7.00: configured for UDMA/33
ata7: EH complete
ata7.00: exception Emask 0x0 SAct 0x0 SErr 0x0 action 0x2
ata7.00: (BMDMA stat 0x4)
ata7.00: cmd ca/00:02:41:00:00/00:00:00:00:00/e0 tag 0 cdb 0x0 data 1024 out
res 51/84:00:42:00:00/00:00:00:00:00/e0 Emask 0x10 (ATA bus error)
ata7: soft resetting port
ata7.00: configured for UDMA/33
ata7: EH complete
ata7.00: exception Emask 0x0 SAct 0x0 SErr 0x0 action 0x2
ata7.00: (BMDMA stat 0x4)
ata7.00: cmd ca/00:02:41:00:00/00:00:00:00:00/e0 tag 0 cdb 0x0 data 1024 out
res 51/84:00:42:00:00/00:00:00:00:00/e0 Emask 0x10 (ATA bus error)
ata7: soft resetting port
ata7.00: configured for UDMA/33
sd 6:0:0:0: [sdb] Result: hostbyte=DID_OK driverbyte=DRIVER_SENSE,SUGGEST_OK
sd 6:0:0:0: [sdb] Sense Key : Aborted Command [current] [descriptor]
Descriptor sense data with sense descriptors (in hex):
72 0b 47 00 00 00 00 0c 00 0a 80 00 00 00 00 00
00 00 00 42
sd 6:0:0:0: [sdb] Add. Sense: Scsi parity error
end_request: I/O error, dev sdb, sector 65
Buffer I/O error on device sdb1, logical block 1
lost page write due to I/O error on sdb1
ata7: EH complete
sd 6:0:0:0: [sdb] 80418240 512-byte hardware sectors (41174 MB)
sd 6:0:0:0: [sdb] Write Protect is off
sd 6:0:0:0: [sdb] Mode Sense: 00 3a 00 00
sd 6:0:0:0: [sdb] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
sd 6:0:0:0: [sdb] 80418240 512-byte hardware sectors (41174 MB)
sd 6:0:0:0: [sdb] Write Protect is off
sd 6:0:0:0: [sdb] Mode Sense: 00 3a 00 00
sd 6:0:0:0: [sdb] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
apm: BIOS version 1.2 Flags 0x07 (Driver version 1.16ac)
apm: disabled on user request.
PCI: Setting latency timer of device 0000:01:00.0 to 64
NVRM: loading NVIDIA UNIX x86 Kernel Module 169.12 Thu Feb 14 17:53:07 PST 2008
usb 7-2.4: USB disconnect, address 4
usb 7-2.4: new full speed USB device using ehci_hcd and address 5
usb 7-2.4: configuration #1 chosen from 1 choice
** Loaded modules:
Module Size Used by
nvidia 7819584 24
ipt_recent 9048 2
nf_conntrack_ipv4 17964 2
xt_state 2560 2
nf_conntrack 60744 2 nf_conntrack_ipv4,xt_state
nfnetlink 5944 2 nf_conntrack_ipv4,nf_conntrack
xt_tcpudp 3232 2
iptable_filter 3104 1
ip_tables 12420 1 iptable_filter
x_tables 14564 4 ipt_recent,xt_state,xt_tcpudp,ip_tables
sr_mod 16580 0
nfs 224684 0
lockd 60584 1 nfs
nfs_acl 3616 1 nfs
sunrpc 158396 4 nfs,lockd,nfs_acl
autofs4 20612 2
ipv6 238500 32
psmouse 36272 0
parport_pc 33956 0
parport 34120 1 parport_pc
pcspkr 3232 0
rtc 12984 0
firewire_ohci 16768 0
firewire_core 39200 1 firewire_ohci
crc_itu_t 2240 1 firewire_core
r8169 29128 0
ahci 20868 0
snd_hda_intel 238712 1
ehci_hcd 31244 0
tsdev 8160 0
joydev 9696 0
usbvision 69288 0
uhci_hcd 23216 0
intel_agp 23316 0
agpgart 32136 2 nvidia,intel_agp
vfat 12224 1
fat 48636 1 vfat
reiserfs 220160 3
ext2 60520 1
dm_snapshot 17060 0
dm_mirror 21152 0
dm_mod 52384 5 dm_snapshot,dm_mirror
it87 17808 0
hwmon_vid 3040 1 it87
i2c_isa 4352 1 it87
eeprom 7344 0
i2c_i801 8752 0
sundance 22528 0
mii 5376 1 sundance
saa7134 121388 0
video_buf 23620 1 saa7134
compat_ioctl32 1472 1 saa7134
ir_kbd_i2c 8816 1 saa7134
i2c_core 23840 8 nvidia,usbvision,it87,i2c_isa,eeprom,i2c_i801,saa7134,ir_kbd_i2c
ir_common 34212 2 saa7134,ir_kbd_i2c
videodev 26816 2 usbvision,saa7134
v4l2_common 16832 3 usbvision,saa7134,videodev
v4l1_compat 12644 2 saa7134,videodev
snd_usb_audio 74624 1
snd_usb_lib 15520 1 snd_usb_audio
snd_cmipci 32704 0
gameport 15208 1 snd_cmipci
snd_pcm_oss 39456 0
snd_mixer_oss 15584 2 snd_pcm_oss
snd_pcm 72612 4 snd_hda_intel,snd_usb_audio,snd_cmipci,snd_pcm_oss
snd_page_alloc 10248 2 snd_hda_intel,snd_pcm
snd_opl3_lib 9952 1 snd_cmipci
snd_hwdep 8964 2 snd_usb_audio,snd_opl3_lib
snd_mpu401_uart 8256 1 snd_cmipci
snd_seq_dummy 3876 0
snd_seq_oss 29600 0
snd_seq_midi 8320 0
snd_seq_midi_event 7008 2 snd_seq_oss,snd_seq_midi
snd_seq 46576 6 snd_seq_dummy,snd_seq_oss,snd_seq_midi,snd_seq_midi_event
snd_timer 21284 3 snd_pcm,snd_opl3_lib,snd_seq
snd_rawmidi 22848 3 snd_usb_lib,snd_mpu401_uart,snd_seq_midi
snd_seq_device 7884 6 snd_opl3_lib,snd_seq_dummy,snd_seq_oss,snd_seq_midi,snd_seq,snd_rawmidi
snd 48548 16 snd_hda_intel,snd_usb_audio,snd_cmipci,snd_pcm_oss,snd_mixer_oss,snd_pcm,snd_opl3_lib,snd_hwdep,snd_mpu401_uart,snd_seq_oss,snd_seq,snd_timer,snd_rawmidi,snd_seq_device
soundcore 7680 2 snd
sata_via 11588 0
sd_mod 27328 1
ata_piix 13476 1
ide_cd 36608 0
cdrom 33056 2 sr_mod,ide_cd
usbhid 26048 0
usbmouse 5440 0
usbcore 125960 8 ehci_hcd,usbvision,uhci_hcd,snd_usb_audio,snd_usb_lib,usbhid,usbmouse
hid 25408 1 usbhid
sg 32796 0
nls_koi8_r 5376 1
nls_cp866 5376 1
ext3 121704 5
jbd 55528 1 ext3
mbcache 8516 2 ext2,ext3
ide_disk 16736 12
ata_generic 7716 0
libata 115760 4 ahci,sata_via,ata_piix,ata_generic
scsi_mod 137036 4 sr_mod,sd_mod,sg,libata
generic 4964 0 [permanent]
jmicron 3744 0 [permanent]
ide_core 114244 4 ide_cd,ide_disk,generic,jmicron
shpchp 31316 0
pci_hotplug 29408 1 shpchp
evdev 9472 1
** PCI devices:
00:00.0 Host bridge [0600]: Intel Corporation Unknown device [8086:29c0] (rev 02)
Subsystem: Giga-byte Technology Unknown device [1458:5000]
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort+ >SERR- <PERR-
Latency: 0
Capabilities: <access denied>
00:01.0 PCI bridge [0604]: Intel Corporation Unknown device [8086:29c1] (rev 02) (prog-if 00 [Normal decode])
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR-
Latency: 0, Cache Line Size: 32 bytes
Bus: primary=00, secondary=01, subordinate=01, sec-latency=0
I/O behind bridge: 0000a000-0000afff
Memory behind bridge: f4000000-f7ffffff
Prefetchable memory behind bridge: 00000000e0000000-00000000efffffff
Secondary status: 66MHz- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- <SERR- <PERR-
BridgeCtl: Parity- SERR- NoISA- VGA+ MAbort- >Reset- FastB2B-
Capabilities: <access denied>
00:1a.0 USB Controller [0c03]: Intel Corporation Unknown device [8086:2937] (rev 02) (prog-if 00 [UHCI])
Subsystem: Giga-byte Technology Unknown device [1458:5004]
Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
Latency: 0
Interrupt: pin A routed to IRQ 16
Region 4: I/O ports at e000 [size=32]
Capabilities: <access denied>
00:1a.1 USB Controller [0c03]: Intel Corporation Unknown device [8086:2938] (rev 02) (prog-if 00 [UHCI])
Subsystem: Giga-byte Technology Unknown device [1458:5004]
Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
Latency: 0
Interrupt: pin B routed to IRQ 20
Region 4: I/O ports at e100 [size=32]
Capabilities: <access denied>
00:1a.2 USB Controller [0c03]: Intel Corporation Unknown device [8086:2939] (rev 02) (prog-if 00 [UHCI])
Subsystem: Giga-byte Technology Unknown device [1458:5004]
Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
Latency: 0
Interrupt: pin C routed to IRQ 19
Region 4: I/O ports at e500 [size=32]
Capabilities: <access denied>
00:1a.7 USB Controller [0c03]: Intel Corporation Unknown device [8086:293c] (rev 02) (prog-if 20 [EHCI])
Subsystem: Giga-byte Technology Unknown device [1458:5006]
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
Latency: 0
Interrupt: pin C routed to IRQ 19
Region 0: Memory at fc105000 (32-bit, non-prefetchable) [size=1K]
Capabilities: <access denied>
00:1b.0 Audio device [0403]: Intel Corporation Unknown device [8086:293e] (rev 02)
Subsystem: Giga-byte Technology Unknown device [1458:a002]
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR-
Latency: 0, Cache Line Size: 32 bytes
Interrupt: pin A routed to IRQ 22
Region 0: Memory at fc100000 (64-bit, non-prefetchable) [size=16K]
Capabilities: <access denied>
00:1c.0 PCI bridge [0604]: Intel Corporation Unknown device [8086:2940] (rev 02) (prog-if 00 [Normal decode])
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR-
Latency: 0, Cache Line Size: 32 bytes
Bus: primary=00, secondary=02, subordinate=02, sec-latency=0
I/O behind bridge: 00009000-00009fff
Secondary status: 66MHz- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- <SERR- <PERR-
BridgeCtl: Parity- SERR- NoISA- VGA- MAbort- >Reset- FastB2B-
Capabilities: <access denied>
00:1c.4 PCI bridge [0604]: Intel Corporation Unknown device [8086:2948] (rev 02) (prog-if 00 [Normal decode])
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR-
Latency: 0, Cache Line Size: 32 bytes
Bus: primary=00, secondary=03, subordinate=03, sec-latency=0
I/O behind bridge: 0000b000-0000bfff
Memory behind bridge: fc000000-fc0fffff
Secondary status: 66MHz- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- <SERR- <PERR-
BridgeCtl: Parity- SERR- NoISA- VGA- MAbort- >Reset- FastB2B-
Capabilities: <access denied>
00:1c.5 PCI bridge [0604]: Intel Corporation Unknown device [8086:294a] (rev 02) (prog-if 00 [Normal decode])
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR-
Latency: 0, Cache Line Size: 32 bytes
Bus: primary=00, secondary=04, subordinate=04, sec-latency=0
I/O behind bridge: 0000c000-0000cfff
Memory behind bridge: f8000000-f9ffffff
Prefetchable memory behind bridge: 0000000080000000-00000000800fffff
Secondary status: 66MHz- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- <SERR- <PERR-
BridgeCtl: Parity- SERR- NoISA- VGA- MAbort- >Reset- FastB2B-
Capabilities: <access denied>
00:1d.0 USB Controller [0c03]: Intel Corporation Unknown device [8086:2934] (rev 02) (prog-if 00 [UHCI])
Subsystem: Giga-byte Technology Unknown device [1458:5004]
Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
Latency: 0
Interrupt: pin A routed to IRQ 21
Region 4: I/O ports at e200 [size=32]
Capabilities: <access denied>
00:1d.1 USB Controller [0c03]: Intel Corporation Unknown device [8086:2935] (rev 02) (prog-if 00 [UHCI])
Subsystem: Giga-byte Technology Unknown device [1458:5004]
Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
Latency: 0
Interrupt: pin B routed to IRQ 18
Region 4: I/O ports at e300 [size=32]
Capabilities: <access denied>
00:1d.2 USB Controller [0c03]: Intel Corporation Unknown device [8086:2936] (rev 02) (prog-if 00 [UHCI])
Subsystem: Giga-byte Technology Unknown device [1458:5004]
Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
Latency: 0
Interrupt: pin C routed to IRQ 19
Region 4: I/O ports at e400 [size=32]
Capabilities: <access denied>
00:1d.7 USB Controller [0c03]: Intel Corporation Unknown device [8086:293a] (rev 02) (prog-if 20 [EHCI])
Subsystem: Giga-byte Technology Unknown device [1458:5006]
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
Latency: 0
Interrupt: pin A routed to IRQ 21
Region 0: Memory at fc104000 (32-bit, non-prefetchable) [size=1K]
Capabilities: <access denied>
00:1e.0 PCI bridge [0604]: Intel Corporation 82801 PCI Bridge [8086:244e] (rev 92) (prog-if 01 [Subtractive decode])
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR-
Latency: 0
Bus: primary=00, secondary=05, subordinate=05, sec-latency=32
I/O behind bridge: 0000d000-0000dfff
Memory behind bridge: fa000000-fbffffff
Prefetchable memory behind bridge: 0000000080100000-00000000801fffff
Secondary status: 66MHz- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort+ <SERR- <PERR-
BridgeCtl: Parity- SERR- NoISA- VGA- MAbort- >Reset- FastB2B-
Capabilities: <access denied>
00:1f.0 ISA bridge [0601]: Intel Corporation Unknown device [8086:2916] (rev 02)
Subsystem: Giga-byte Technology Unknown device [1458:5001]
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR+ FastB2B-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
Latency: 0
Capabilities: <access denied>
00:1f.2 IDE interface [0101]: Intel Corporation Unknown device [8086:2920] (rev 02) (prog-if 8a [Master SecP PriP])
Subsystem: Giga-byte Technology Unknown device [1458:b002]
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
Status: Cap+ 66MHz+ UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
Latency: 0
Interrupt: pin B routed to IRQ 18
Region 0: I/O ports at 01f0 [size=8]
Region 1: I/O ports at 03f4 [size=1]
Region 2: I/O ports at 0170 [size=8]
Region 3: I/O ports at 0374 [size=1]
Region 4: I/O ports at f000 [size=16]
Region 5: I/O ports at fc00 [size=16]
Capabilities: <access denied>
00:1f.3 SMBus [0c05]: Intel Corporation Unknown device [8086:2930] (rev 02)
Subsystem: Giga-byte Technology Unknown device [1458:5001]
Control: I/O+ Mem+ BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
Status: Cap- 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
Interrupt: pin C routed to IRQ 19
Region 0: Memory at fc106000 (64-bit, non-prefetchable) [size=256]
Region 4: I/O ports at 0500 [size=32]
00:1f.5 IDE interface [0101]: Intel Corporation Unknown device [8086:2926] (rev 02) (prog-if 85 [Master SecO PriO])
Subsystem: Giga-byte Technology Unknown device [1458:b002]
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
Status: Cap+ 66MHz+ UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
Latency: 0
Interrupt: pin B routed to IRQ 18
Region 0: I/O ports at e700 [size=8]
Region 1: I/O ports at e800 [size=4]
Region 2: I/O ports at e900 [size=8]
Region 3: I/O ports at ea00 [size=4]
Region 4: I/O ports at eb00 [size=16]
Region 5: I/O ports at ec00 [size=16]
Capabilities: <access denied>
01:00.0 VGA compatible controller [0300]: nVidia Corporation Unknown device [10de:0611] (rev a2) (prog-if 00 [VGA])
Subsystem: LeadTek Research Inc. Unknown device [107d:2ab0]
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR-
Latency: 0
Interrupt: pin A routed to IRQ 16
Region 0: Memory at f6000000 (32-bit, non-prefetchable) [size=16M]
Region 1: Memory at e0000000 (64-bit, prefetchable) [size=256M]
Region 3: Memory at f4000000 (64-bit, non-prefetchable) [size=32M]
Region 5: I/O ports at a000 [size=128]
[virtual] Expansion ROM at f7000000 [disabled] [size=128K]
Capabilities: <access denied>
03:00.0 SATA controller [0106]: JMicron Technologies, Inc. JMicron 20360/20363 AHCI Controller [197b:2363] (rev 02) (prog-if 01 [AHCI 1.0])
Subsystem: Giga-byte Technology Unknown device [1458:b000]
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR-
Latency: 0, Cache Line Size: 32 bytes
Interrupt: pin A routed to IRQ 16
Region 5: Memory at fc000000 (32-bit, non-prefetchable) [size=8K]
Capabilities: <access denied>
03:00.1 IDE interface [0101]: JMicron Technologies, Inc. JMicron 20360/20363 AHCI Controller [197b:2363] (rev 02) (prog-if 85 [Master SecO PriO])
Subsystem: Giga-byte Technology Unknown device [1458:b000]
Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR-
Latency: 0
Interrupt: pin B routed to IRQ 17
Region 0: I/O ports at b000 [size=8]
Region 1: I/O ports at b100 [size=4]
Region 2: I/O ports at b200 [size=8]
Region 3: I/O ports at b300 [size=4]
Region 4: I/O ports at b400 [size=16]
Capabilities: <access denied>
04:00.0 Ethernet controller [0200]: Realtek Semiconductor Co., Ltd. RTL8111/8168B PCI Express Gigabit Ethernet controller [10ec:8168] (rev 01)
Subsystem: Giga-byte Technology Unknown device [1458:e000]
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR-
Latency: 0, Cache Line Size: 32 bytes
Interrupt: pin A routed to IRQ 17
Region 0: I/O ports at c000 [size=256]
Region 2: Memory at f9000000 (64-bit, non-prefetchable) [size=4K]
[virtual] Expansion ROM at 80000000 [disabled] [size=64K]
Capabilities: <access denied>
05:01.0 RAID bus controller [0104]: VIA Technologies, Inc. VT6421 IDE RAID Controller [1106:3249] (rev 50)
Subsystem: VIA Technologies, Inc. VT6421 IDE RAID Controller [1106:3249]
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
Latency: 32
Interrupt: pin A routed to IRQ 18
Region 0: I/O ports at d000 [size=16]
Region 1: I/O ports at d100 [size=16]
Region 2: I/O ports at d200 [size=16]
Region 3: I/O ports at d300 [size=16]
Region 4: I/O ports at d400 [size=32]
Region 5: I/O ports at d500 [size=256]
[virtual] Expansion ROM at 80100000 [disabled] [size=64K]
Capabilities: <access denied>
05:06.0 FireWire (IEEE 1394) [0c00]: Texas Instruments TSB43AB23 IEEE-1394a-2000 Controller (PHY/Link) [104c:8024] (prog-if 10 [OHCI])
Subsystem: Giga-byte Technology Unknown device [1458:1000]
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
Latency: 32 (500ns min, 1000ns max), Cache Line Size: 32 bytes
Interrupt: pin A routed to IRQ 19
Region 0: Memory at fb004000 (32-bit, non-prefetchable) [size=2K]
Region 1: Memory at fb000000 (32-bit, non-prefetchable) [size=16K]
Capabilities: <access denied>
-- System Information:
Debian Release: 4.0
APT prefers stable
APT policy: (600, 'stable')
Architecture: i386 (i686)
Shell: /bin/sh linked to /bin/bash
Kernel: Linux 2.6.22-4-686
Locale: LANG=ru_RU.KOI8-R, LC_CTYPE=ru_RU.KOI8-R (charmap=KOI8-R)
Versions of packages linux-image-2.6.22-4-686 depends on:
ii module-init-tools 3.3-pre4-2 tools for managing Linux kernel mo
ii yaird [linux-initramfs-tool] 0.0.12-18 Yet Another mkInitRD
Versions of packages linux-image-2.6.22-4-686 recommends:
pn libc6-i686 <none> (no description available)
-- debconf information:
linux-image-2.6.22-4-686/preinst/abort-install-2.6.22-4-686:
linux-image-2.6.22-4-686/preinst/lilo-has-ramdisk:
linux-image-2.6.22-4-686/preinst/failed-to-move-modules-2.6.22-4-686:
linux-image-2.6.22-4-686/preinst/elilo-initrd-2.6.22-4-686: true
linux-image-2.6.22-4-686/postinst/kimage-is-a-directory:
linux-image-2.6.22-4-686/postinst/old-system-map-link-2.6.22-4-686: true
linux-image-2.6.22-4-686/postinst/bootloader-test-error-2.6.22-4-686:
linux-image-2.6.22-4-686/postinst/create-kimage-link-2.6.22-4-686: true
linux-image-2.6.22-4-686/postinst/depmod-error-2.6.22-4-686: false
shared/kernel-image/really-run-bootloader: true
linux-image-2.6.22-4-686/preinst/bootloader-initrd-2.6.22-4-686: true
linux-image-2.6.22-4-686/prerm/would-invalidate-boot-loader-2.6.22-4-686: true
linux-image-2.6.22-4-686/preinst/abort-overwrite-2.6.22-4-686:
linux-image-2.6.22-4-686/postinst/depmod-error-initrd-2.6.22-4-686: false
linux-image-2.6.22-4-686/preinst/already-running-this-2.6.22-4-686:
linux-image-2.6.22-4-686/prerm/removing-running-kernel-2.6.22-4-686: true
linux-image-2.6.22-4-686/postinst/old-dir-initrd-link-2.6.22-4-686: true
linux-image-2.6.22-4-686/preinst/lilo-initrd-2.6.22-4-686: true
linux-image-2.6.22-4-686/preinst/initrd-2.6.22-4-686:
linux-image-2.6.22-4-686/postinst/old-initrd-link-2.6.22-4-686: true
linux-image-2.6.22-4-686/preinst/overwriting-modules-2.6.22-4-686: true
linux-image-2.6.22-4-686/postinst/bootloader-error-2.6.22-4-686:
--- End Message ---