--- Begin Message ---
- To: Debian Bug Tracking System <submit@bugs.debian.org>
- Subject: linux-image-2.6.21-1-powerpc: Suspend fails on PowerBook
- From: Mark Brown <broonie@sirena.org.uk>
- Date: Tue, 19 Jun 2007 13:00:32 +0100
- Message-id: <20070619120032.3895.53824.reportbug@localhost.localdomain>
Package: linux-image-2.6.21-1-powerpc
Version: 2.6.21-4
Severity: important
Since upgrading to this kernel version any attempt to suspend my laptop
has failed. The machine begins to suspend, complains that it cannot
suspend and then attempts to abort the suspend but fails to do so,
forcing a manual reset. Both aspects of this are a problem - the
failure to abort is a more serious issue for me since it can cause data
loss.
When I have access to something I can use to capture the console output
I will provie that, unfortunately I don't have anything right now.
The machine is:
processor : 0
cpu : 7447A, altivec supported
clock : 749.999000MHz
revision : 0.1 (pvr 8003 0101)
bogomips : 36.73
timebase : 18432000
platform : PowerMac
machine : PowerBook5,4
motherboard : PowerBook5,4 MacRISC3 Power Macintosh
detected as : 287 (PowerBook G4 15")
pmac flags : 0000001b
L2 cache : 512K unified
pmac-generation : NewWorld
-- Package-specific info:
** Version: Linux version 2.6.21-1-powerpc (Debian 2.6.21-4) (waldi@debian.org) (gcc version 4.1.3 20070518 (prerelease) (Debian 4.1.2-8)) #1 Sat May 26 14:30:26 CEST 2007
** Not tainted
** Kernel log:
Yenta: Routing CardBus interrupts to PCI
Yenta TI: socket 0001:10:13.0, mfunc 0x00001002, devctl 0x60
Yenta: ISA IRQ mask 0x0000, PCI irq 53
Socket status: 30000087
pcmcia: parent PCI bridge I/O window: 0x0 - 0x7fffff
pcmcia: parent PCI bridge Memory window: 0xf3000000 - 0xf3ffffff
pcmcia: parent PCI bridge Memory window: 0x80000000 - 0xafffffff
bcm43xx driver
PCI: Enabling device 0001:10:12.0 (0004 -> 0006)
bcm43xx: Chip ID 0x4306, rev 0x3
bcm43xx: Number of cores: 5
bcm43xx: Core 0: ID 0x800, rev 0x4, vendor 0x4243
bcm43xx: Core 1: ID 0x812, rev 0x5, vendor 0x4243
bcm43xx: Core 2: ID 0x80d, rev 0x2, vendor 0x4243
bcm43xx: Core 3: ID 0x807, rev 0x2, vendor 0x4243
bcm43xx: Core 4: ID 0x804, rev 0x9, vendor 0x4243
bcm43xx: PHY connected
bcm43xx: Detected PHY: Analog: 2, Type 2, Revision 2
bcm43xx: Detected Radio: ID: 2205017f (Manuf: 17f Ver: 2050 Rev: 2)
bcm43xx: Radio turned off
bcm43xx: Radio turned off
ieee1394: Initialized config rom entry `ip1394'
PCI: Enabling device 0001:10:1b.2 (0004 -> 0006)
ehci_hcd 0001:10:1b.2: EHCI Host Controller
ehci_hcd 0001:10:1b.2: new USB bus registered, assigned bus number 4
ehci_hcd 0001:10:1b.2: irq 63, io mem 0xa0000000
ehci_hcd 0001:10:1b.2: USB 2.0 started, EHCI 1.00, driver 10 Dec 2004
usb usb4: configuration #1 chosen from 1 choice
hub 4-0:1.0: USB hub found
hub 4-0:1.0: 5 ports detected
Bluetooth: Core ver 2.11
NET: Registered protocol family 31
Bluetooth: HCI device and connection manager initialized
Bluetooth: HCI socket layer initialized
PowerMac i2c bus pmu 2 registered
PowerMac i2c bus pmu 1 registered
PowerMac i2c bus mac-io 0 registered
PowerMac i2c bus uni-n 1 registered
PowerMac i2c bus uni-n 0 registered
sungem.c:v0.98 8/24/03 David S. Miller (davem@redhat.com)
PHY ID: 1410cc1, addr: 0
eth1: Sun GEM (PCI) 10/100/1000BaseT Ethernet 00:0d:93:c1:97:b6
eth1: Found Marvell 88E1111 PHY
PCI: Enabling device 0002:24:0e.0 (0000 -> 0002)
ohci1394: fw-host0: OHCI-1394 1.1 (PCI): IRQ=[40] MMIO=[f5000000-f50007ff] Max Packet=[4096] IR/IT contexts=[8/8]
Bluetooth: HCI USB driver ver 2.9
hdc: ATAPI 24X DVD-ROM DVD-R CD-R/RW drive, 2048kB Cache, (U)DMA
Uniform CD-ROM driver Revision: 3.20
usbcore: registered new interface driver hci_usb
snd-aoa-fabric-layout: found bus with layout 51
snd-aoa-fabric-layout: Using direct GPIOs
snd-aoa-codec-tas: found 'deq' node
snd-aoa-fabric-layout: can use this codec
snd-aoa-codec-tas: tas found, addr 0x35 on /pci@f2000000/mac-io@17/i2c@18000/deq@6a
ieee1394: Host added: ID:BUS[0-00:1023] GUID[000d93fffec197b6]
eth1394: eth2: IEEE-1394 IPv4 over 1394 Ethernet (fw-host0)
Adding 500644k swap on /dev/hda6. Priority:-1 extents:1 across:500644k
EXT3 FS on hda3, internal journal
SCSI subsystem initialized
snd-powermac no longer handles any machines with a layout-id property in the device-tree, use snd-aoa.
apm_emu: APM Emulation 0.5 initialized.
device-mapper: ioctl: 4.11.0-ioctl (2006-10-12) initialised: dm-devel@redhat.com
pcmcia: Detected deprecated PCMCIA ioctl usage from process: discover.
pcmcia: This interface will soon be removed from the kernel; please expect breakage unless you upgrade to new tools.
pcmcia: see http://www.kernel.org/pub/linux/utils/kernel/pcmcia/pcmcia.html for details.
audit(1182253431.182:2): audit_pid=1937 old=0 by auid=4294967295
NET: Registered protocol family 10
lo: Disabled Privacy Extensions
Installing knfsd (copyright (C) 1996 okir@monad.swb.de).
NFSD: Using /var/lib/nfs/v4recovery as the NFSv4 state recovery directory
NFSD: starting 90-second grace period
Bluetooth: L2CAP ver 2.8
Bluetooth: L2CAP socket layer initialized
Bluetooth: RFCOMM socket layer initialized
Bluetooth: RFCOMM TTY layer initialized
Bluetooth: RFCOMM ver 1.8
ADDRCONF(NETDEV_UP): eth1: link is not ready
bcm43xx: PHY connected
bcm43xx: Microcode rev 0x127, pl 0xe (2005-04-18 02:36:27)
bcm43xx: Radio turned on
bcm43xx: Radio enabled by hardware
bcm43xx: Chip initialized
bcm43xx: 30-bit DMA initialized
bcm43xx: Keys cleared
bcm43xx: Selected 802.11 core (phytype 2)
ADDRCONF(NETDEV_UP): eth0: link is not ready
bcm43xx: set security called, .level = 0, .enabled = 0, .encrypt = 0
SoftMAC: Open Authentication completed with 00:18:f8:fa:02:cb
ADDRCONF(NETDEV_CHANGE): eth0: link becomes ready
[drm] Initialized drm 1.1.0 20060810
[drm] Initialized radeon 1.25.0 20060524 on minor 0
agpgart: Putting AGP V2 device at 0000:00:0b.0 into 1x mode
agpgart: Putting AGP V2 device at 0000:00:10.0 into 1x mode
[drm] Setting GART location based on new memory map
[drm] Loading R300 Microcode
[drm] writeback test succeeded in 1 usecs
eth1: Link is up at 1000 Mbps, full-duplex.
eth1: Pause is disabled
ADDRCONF(NETDEV_CHANGE): eth1: link becomes ready
SoftMAC: Open Authentication completed with 00:18:f8:fa:02:cb
** Loaded modules:
Module Size Used by
binfmt_misc 13288 1
radeon 141640 2
drm 94328 3 radeon
rfcomm 44060 0
l2cap 24996 5 rfcomm
nfs 280008 0
nfsd 244524 17
exportfs 6272 1 nfsd
lockd 75032 3 nfs,nfsd
nfs_acl 4000 2 nfs,nfsd
sunrpc 195616 13 nfs,nfsd,lockd,nfs_acl
autofs4 24932 0
ipv6 287180 24
dm_snapshot 20320 0
dm_mirror 24212 0
dm_mod 66444 2 dm_snapshot,dm_mirror
cpufreq_userspace 4564 1
apm_emu 7820 1
sr_mod 19972 0
snd_powermac 48160 0
sbp2 24516 0
scsi_mod 177708 2 sr_mod,sbp2
eth1394 21124 0
snd_aoa_codec_tas 15104 2
snd_aoa_fabric_layout 13832 1
snd_aoa 20576 2 snd_aoa_codec_tas,snd_aoa_fabric_layout
snd_aoa_i2sbus 24356 1
snd_pcm_oss 52096 0
snd_mixer_oss 20384 1 snd_pcm_oss
snd_pcm 92004 3 snd_powermac,snd_aoa_i2sbus,snd_pcm_oss
snd_timer 25828 1 snd_pcm
snd_page_alloc 11208 1 snd_pcm
snd 67476 11 snd_powermac,snd_aoa_codec_tas,snd_aoa_fabric_layout,snd_aoa,snd_aoa_i2sbus,snd_pcm_oss,snd_mixer_oss,snd_pcm,snd_timer
soundcore 8900 1 snd
pcmcia 44080 0
snd_aoa_soundbus 7908 2 snd_aoa_fabric_layout,snd_aoa_i2sbus
ide_cd 47236 0
hci_usb 18364 2
cdrom 43164 2 sr_mod,ide_cd
ohci1394 41488 0
i2c_powermac 5984 0
bluetooth 62124 7 rfcomm,l2cap,hci_usb
sungem 34916 0
sungem_phy 12896 1 sungem
ehci_hcd 37196 0
ieee1394 110672 3 sbp2,eth1394,ohci1394
bcm43xx 441276 0
firmware_class 11168 2 pcmcia,bcm43xx
ieee80211softmac 32032 1 bcm43xx
yenta_socket 29740 1
rsrc_nonstatic 12704 1 yenta_socket
ieee80211 34661 2 bcm43xx,ieee80211softmac
ieee80211_crypt 6464 1 ieee80211
pcmcia_core 46968 3 pcmcia,yenta_socket,rsrc_nonstatic
uninorth_agp 11724 1
agpgart 40284 2 drm,uninorth_agp
tsdev 9120 0
ext3 152904 1
jbd 67880 1 ext3
mbcache 9540 1 ext3
ide_disk 18784 3
evdev 12448 8
** PCI devices:
0000:00:0b.0 Host bridge [0600]: Apple Computer Inc. UniNorth 2 AGP [106b:0034]
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV+ VGASnoop- ParErr- Stepping- SERR- FastB2B-
Status: Cap+ 66MHz+ UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort+ >SERR- <PERR-
Latency: 16, Cache Line Size: 32 bytes
Capabilities: <access denied>
0000:00:10.0 VGA compatible controller [0300]: ATI Technologies Inc RV350 [Mobility Radeon 9600 M10] [1002:4e50] (prog-if 00 [VGA])
Subsystem: ATI Technologies Inc RV350 [Mobility Radeon 9600 M10] [1002:4e50]
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
Status: Cap+ 66MHz+ UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
Latency: 255 (2000ns min), Cache Line Size: 32 bytes
Interrupt: pin A routed to IRQ 48
Region 0: Memory at b8000000 (32-bit, prefetchable) [size=128M]
Region 1: I/O ports at 0400 [size=256]
Region 2: Memory at b0000000 (32-bit, non-prefetchable) [size=64K]
Expansion ROM at f1000000 [disabled] [size=128K]
Capabilities: <access denied>
0001:10:0b.0 Host bridge [0600]: Apple Computer Inc. UniNorth 2 PCI [106b:0035]
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV+ VGASnoop- ParErr- Stepping- SERR- FastB2B-
Status: Cap- 66MHz+ UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort+ >SERR- <PERR-
Latency: 16, Cache Line Size: 32 bytes
0001:10:12.0 Network controller [0280]: Broadcom Corporation BCM4306 802.11b/g Wireless LAN Controller [14e4:4320] (rev 03)
Subsystem: Apple Computer Inc. AirPort Extreme [106b:004e]
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR-
Latency: 16
Interrupt: pin A routed to IRQ 52
Region 0: Memory at a0006000 (32-bit, non-prefetchable) [size=8K]
Capabilities: <access denied>
0001:10:13.0 CardBus bridge [0607]: Texas Instruments PCI1510 PC card Cardbus Controller [104c:ac56]
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
Latency: 168, Cache Line Size: 32 bytes
Interrupt: pin A routed to IRQ 53
Region 0: Memory at a0004000 (32-bit, non-prefetchable) [size=4K]
Bus: primary=10, secondary=11, subordinate=14, sec-latency=176
Memory window 0: 90000000-9ffff000 (prefetchable)
Memory window 1: f3000000-f33ff000
I/O window 0: 00001000-000011ff
I/O window 1: 00001400-000015ff
BridgeCtl: Parity- SERR- ISA- VGA- MAbort- >Reset+ 16bInt+ PostWrite+
16-bit legacy interface ports at 0001
0001:10:17.0 Unknown class [ff00]: Apple Computer Inc. KeyLargo/Intrepid Mac I/O [106b:003e]
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
Status: Cap- 66MHz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
Latency: 16, Cache Line Size: 32 bytes
Region 0: Memory at 80000000 (32-bit, non-prefetchable) [size=512K]
0001:10:18.0 USB Controller [0c03]: Apple Computer Inc. KeyLargo/Intrepid USB [106b:003f] (prog-if 10 [OHCI])
Control: I/O- Mem- BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
Status: Cap- 66MHz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
Interrupt: pin A routed to IRQ 27
0001:10:19.0 USB Controller [0c03]: Apple Computer Inc. KeyLargo/Intrepid USB [106b:003f] (prog-if 10 [OHCI])
Control: I/O- Mem- BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
Status: Cap- 66MHz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
Interrupt: pin A routed to IRQ 28
0001:10:1a.0 USB Controller [0c03]: Apple Computer Inc. KeyLargo/Intrepid USB [106b:003f] (prog-if 10 [OHCI])
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
Status: Cap- 66MHz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
Latency: 16 (750ns min, 21500ns max), Cache Line Size: 32 bytes
Interrupt: pin A routed to IRQ 29
Region 0: Memory at a0003000 (32-bit, non-prefetchable) [size=4K]
0001:10:1b.0 USB Controller [0c03]: NEC Corporation USB [1033:0035] (rev 43) (prog-if 10 [OHCI])
Subsystem: NEC Corporation Hama USB 2.0 CardBus [1033:0035]
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
Latency: 16 (250ns min, 10500ns max), Cache Line Size: 32 bytes
Interrupt: pin A routed to IRQ 63
Region 0: Memory at a0002000 (32-bit, non-prefetchable) [size=4K]
Capabilities: <access denied>
0001:10:1b.1 USB Controller [0c03]: NEC Corporation USB [1033:0035] (rev 43) (prog-if 10 [OHCI])
Subsystem: NEC Corporation Hama USB 2.0 CardBus [1033:0035]
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
Latency: 16 (250ns min, 10500ns max), Cache Line Size: 32 bytes
Interrupt: pin B routed to IRQ 63
Region 0: Memory at a0001000 (32-bit, non-prefetchable) [size=4K]
Capabilities: <access denied>
0001:10:1b.2 USB Controller [0c03]: NEC Corporation USB 2.0 [1033:00e0] (rev 04) (prog-if 20 [EHCI])
Subsystem: NEC Corporation USB 2.0 [1033:00e0]
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV+ VGASnoop- ParErr- Stepping- SERR- FastB2B-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
Latency: 16 (4000ns min, 8500ns max), Cache Line Size: 32 bytes
Interrupt: pin C routed to IRQ 63
Region 0: Memory at a0000000 (32-bit, non-prefetchable) [size=256]
Capabilities: <access denied>
0002:24:0b.0 Host bridge [0600]: Apple Computer Inc. UniNorth 2 Internal PCI [106b:0036]
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV+ VGASnoop- ParErr- Stepping- SERR- FastB2B-
Status: Cap- 66MHz+ UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort+ >SERR- <PERR-
Latency: 16, Cache Line Size: 32 bytes
0002:24:0d.0 Unknown class [ff00]: Apple Computer Inc. UniNorth/Intrepid ATA/100 [106b:003b]
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
Status: Cap- 66MHz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR+
Latency: 32, Cache Line Size: 32 bytes
Interrupt: pin ? routed to IRQ 39
Region 0: Memory at f5004000 (32-bit, non-prefetchable) [size=16K]
0002:24:0e.0 FireWire (IEEE 1394) [0c00]: Apple Computer Inc. UniNorth 2 FireWire [106b:0031] (rev 81) (prog-if 10 [OHCI])
Subsystem: Apple Computer Inc. iBook G4 2004 [106b:5811]
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
Latency: 64 (3000ns min, 6000ns max), Cache Line Size: 32 bytes
Interrupt: pin A routed to IRQ 40
Region 0: Memory at f5000000 (32-bit, non-prefetchable) [size=4K]
Capabilities: <access denied>
0002:24:0f.0 Ethernet controller [0200]: Apple Computer Inc. UniNorth 2 GMAC (Sun GEM) [106b:0032] (rev 80)
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV+ VGASnoop- ParErr- Stepping- SERR- FastB2B-
Status: Cap- 66MHz+ UDF- FastB2B+ ParErr- DEVSEL=slow >TAbort- <TAbort- <MAbort- >SERR- <PERR+
Latency: 16 (16000ns min, 16000ns max), Cache Line Size: 32 bytes
Interrupt: pin A routed to IRQ 41
Region 0: Memory at f5200000 (32-bit, non-prefetchable) [size=2M]
Expansion ROM at f5100000 [disabled] [size=1M]
-- System Information:
Debian Release: lenny/sid
APT prefers unstable
APT policy: (500, 'unstable')
Architecture: powerpc (ppc)
Kernel: Linux 2.6.21-1-powerpc
Locale: LANG=en_GB.UTF-8, LC_CTYPE=en_GB.UTF-8 (charmap=UTF-8)
Shell: /bin/sh linked to /bin/bash
Versions of packages linux-image-2.6.21-1-powerpc depends on:
ii mkvmlinuz 33 create a kernel to boot a PowerPC
ii module-init-tools 3.3-pre11-3 tools for managing Linux kernel mo
ii yaird [linux-initramfs-tool] 0.0.12-20 Yet Another mkInitRD
linux-image-2.6.21-1-powerpc recommends no packages.
-- debconf information:
linux-image-2.6.21-1-powerpc/preinst/lilo-has-ramdisk:
linux-image-2.6.21-1-powerpc/postinst/bootloader-error-2.6.21-1-powerpc:
linux-image-2.6.21-1-powerpc/preinst/overwriting-modules-2.6.21-1-powerpc: true
linux-image-2.6.21-1-powerpc/postinst/bootloader-test-error-2.6.21-1-powerpc:
linux-image-2.6.21-1-powerpc/preinst/initrd-2.6.21-1-powerpc:
linux-image-2.6.21-1-powerpc/preinst/failed-to-move-modules-2.6.21-1-powerpc:
linux-image-2.6.21-1-powerpc/preinst/abort-overwrite-2.6.21-1-powerpc:
* linux-image-2.6.21-1-powerpc/preinst/already-running-this-2.6.21-1-powerpc:
linux-image-2.6.21-1-powerpc/postinst/old-initrd-link-2.6.21-1-powerpc: true
shared/kernel-image/really-run-bootloader: true
linux-image-2.6.21-1-powerpc/preinst/bootloader-initrd-2.6.21-1-powerpc: true
linux-image-2.6.21-1-powerpc/prerm/removing-running-kernel-2.6.21-1-powerpc: true
linux-image-2.6.21-1-powerpc/postinst/old-dir-initrd-link-2.6.21-1-powerpc: true
linux-image-2.6.21-1-powerpc/postinst/depmod-error-initrd-2.6.21-1-powerpc: false
linux-image-2.6.21-1-powerpc/postinst/old-system-map-link-2.6.21-1-powerpc: true
linux-image-2.6.21-1-powerpc/preinst/elilo-initrd-2.6.21-1-powerpc: true
linux-image-2.6.21-1-powerpc/preinst/abort-install-2.6.21-1-powerpc:
linux-image-2.6.21-1-powerpc/postinst/create-kimage-link-2.6.21-1-powerpc: true
linux-image-2.6.21-1-powerpc/preinst/lilo-initrd-2.6.21-1-powerpc: true
linux-image-2.6.21-1-powerpc/prerm/would-invalidate-boot-loader-2.6.21-1-powerpc: true
linux-image-2.6.21-1-powerpc/postinst/depmod-error-2.6.21-1-powerpc: false
linux-image-2.6.21-1-powerpc/postinst/kimage-is-a-directory:
--- End Message ---